Abstract: Energy dissipation in drops has been investigated by
physical models. After determination of effective parameters on the
phenomenon, three drops with different heights have been
constructed from Plexiglas. They have been installed in two existing
flumes in the hydraulic laboratory. Several runs of physical models
have been undertaken to measured required parameters for
determination of the energy dissipation. Results showed that the
energy dissipation in drops depend on the drop height and discharge.
Predicted relative energy dissipations varied from 10.0% to 94.3%.
This work has also indicated that the energy loss at drop is mainly
due to the mixing of the jet with the pool behind the jet that causes
air bubble entrainment in the flow. Statistical model has been
developed to predict the energy dissipation in vertical drops denotes
nonlinear correlation between effective parameters. Further an
artificial neural networks (ANNs) approach was used in this paper to
develop an explicit procedure for calculating energy loss at drops
using NeuroSolutions. Trained network was able to predict the
response with R2 and RMSE 0.977 and 0.0085 respectively. The
performance of ANN was found effective when compared to
regression equations in predicting the energy loss.
Abstract: In this paper we propose a new knowledge model using
the Dempster-Shafer-s evidence theory for image segmentation and
fusion. The proposed method is composed essentially of two steps.
First, mass distributions in Dempster-Shafer theory are obtained from
the membership degrees of each pixel covering the three image
components (R, G and B). Each membership-s degree is determined by
applying Fuzzy C-Means (FCM) clustering to the gray levels of the
three images. Second, the fusion process consists in defining three
discernment frames which are associated with the three images to be
fused, and then combining them to form a new frame of discernment.
The strategy used to define mass distributions in the combined
framework is discussed in detail. The proposed fusion method is
illustrated in the context of image segmentation. Experimental
investigations and comparative studies with the other previous methods
are carried out showing thus the robustness and superiority of the
proposed method in terms of image segmentation.
Abstract: In a none-super-competitive environment the concepts
of closed system, management control remains to be the dominant
guiding concept to management. The merits of closed loop have been
the sources of most of the management literature and culture for
many decades. It is a useful exercise to investigate and poke into the
dynamics of the control loop phenomenon and draws some lessons to
use for refining the practice of management. This paper examines the
multitude of lessons abstracted from the behavior of the Input /output
/feedback control loop model, which is the core of control theory.
There are numerous lessons that can be learned from the insights this
model would provide and how it parallels the management dynamics
of the organization. It is assumed that an organization is basically a
living system that interacts with the internal and external variables. A
viable control loop is the one that reacts to the variation in the
environment and provide or exert a corrective action. In managing
organizations this is reflected in organizational structure and
management control practices. This paper will report findings that
were a result of examining several abstract scenarios that are
exhibited in the design, operation, and dynamics of the control loop
and how they are projected on the functioning of the organization.
Valuable lessons are drawn in trying to find parallels and new
paradigms, and how the control theory science is reflected in the
design of the organizational structure and management practices. The
paper is structured in a logical and perceptive format. Further
research is needed to extend these findings.
Abstract: Electronics Products that achieve high levels of integrated communications, computing and entertainment, multimedia features in small, stylish and robust new form factors are winning in the market place. Due to the high costs that an industry may undergo and how a high yield is directly proportional to high profits, IC (Integrated Circuit) manufacturers struggle to maximize yield, but today-s customers demand miniaturization, low costs, high performance and excellent reliability making the yield maximization a never ending research of an enhanced assembly process. With factors such as minimum tolerances, tighter parameter variations a systematic approach is needed in order to predict the assembly process. In order to evaluate the quality of upcoming circuits, yield models are used which not only predict manufacturing costs but also provide vital information in order to ease the process of correction when the yields fall below expectations. For an IC manufacturer to obtain higher assembly yields all factors such as boards, placement, components, the material from which the components are made of and processes must be taken into consideration. Effective placement yield depends heavily on machine accuracy and the vision of the system which needs the ability to recognize the features on the board and component to place the device accurately on the pads and bumps of the PCB. There are currently two methods for accurate positioning, using the edge of the package and using solder ball locations also called footprints. The only assumption that a yield model makes is that all boards and devices are completely functional. This paper will focus on the Monte Carlo method which consists in a class of computational algorithms (information processed algorithms) which depends on repeated random samplings in order to compute the results. This method utilized in order to recreate the simulation of placement and assembly processes within a production line.
Abstract: Colored Petri Nets (CPN) are very known kind of
high level Petri nets. With sound and complete semantics, rewriting
logic is one of very powerful logics in description and verification of
non-deterministic concurrent systems. Recently, CPN semantics are
defined in terms of rewriting logic, allowing us to built models by
formal reasoning. In this paper, we propose an automatic translation
of CPN to the rewriting logic language Maude. This tool allows
graphical editing and simulating CPN. The tool allows the user
drawing a CPN graphically and automatic translating the graphical
representation of the drawn CPN to Maude specification. Then,
Maude language is used to perform the simulation of the resulted
Maude specification. It is the first rewriting logic based environment
for this category of Petri Nets.
Abstract: High-frequency (HF) communications have been used by military organizations for more than 90 years. The opportunity of very long range communications without the need for advanced equipment makes HF a convenient and inexpensive alternative of satellite communications. Besides the advantages, voice and data transmission over HF is a challenging task, because the HF channel generally suffers from Doppler shift and spread, multi-path, cochannel interference, and many other sources of noise. In constructing an HF data modem, all these effects must be taken into account. STANAG 4539 is a NATO standard for high-speed data transmission over HF. It allows data rates up to 12800 bps over an HF channel of 3 kHz. In this work, an efficient implementation of STANAG 4539 on a single Texas Instruments- TMS320C6747 DSP chip is described. The state-of-the-art algorithms used in the receiver and the efficiency of the implementation enables real-time high-speed data / digitized voice transmission over poor HF channels.
Abstract: Post cracking behavior and load –bearing capacity of
the steel fiber reinforced high-strength concrete (SFRHSC) are
dependent on the number of fibers are crossing the weakest crack
(bridged the crack) and their orientation to the crack surface. Filling
the mould by SFRHSC, fibers are moving and rotating with the
concrete matrix flow till the motion stops in each internal point of the
concrete body. Filling the same mould from the different ends
SFRHSC samples with the different internal structures (and different
strength) can be obtained. Numerical flow simulations (using Newton
and Bingham flow models) were realized, as well as single fiber
planar motion and rotation numerical and experimental investigation
(in viscous flow) was performed. X-ray pictures for prismatic
samples were obtained and internal fiber positions and orientations
were analyzed. Similarly fiber positions and orientations in cracked
cross-section were recognized and were compared with numerically
simulated. Structural SFRHSC fracture model was created based on
single fiber pull-out laws, which were determined experimentally.
Model predictions were validated by 15x15x60cm prisms 4 point
bending tests.
Abstract: Purpose of this paper is two-folded. At first it explains
the major problems that are causing stagnation in brownfield
redevelopment. In addition, these problems given the context of the
present multi-actor built environment are becoming more complex to
observe. Therefore, this paper suggests also a prospective decisionmaking
approach that is the most appropriate to observe and react on
the given stagnation problems. Such an approach should be regarded
as prescriptive-interactive decision-making approach, a barely
established branch. This approach should offer models that have
prescriptive as well as an interactive component enabling them to
successfully cope with the multi-actor environment. Overall, this
paper provides up-to-date insight on the brownfield stagnation by
gradually introducing the nowadays major problems and offers a
prospective decision-making approach how these problems could be
tackled.
Abstract: The main aim of this paper is to develop and calibrate
an econometric model for modeling prices of long term electricity
futures contracts. The calibration of our model is performed on data
from EEX AG allowing us to capture the specific features of German
electricity market. The data sample contains several structural breaks
which have to be taken into account for modeling. We model the data
with an ARIMAX model which reveals high correlation between the
price of electricity futures contracts and prices of LT futures
contracts of fuels (namely coal, natural gas and crude oil). Besides
this, also a share price index of representative electricity companies
traded on Xetra, spread between 10Y and 1Y German bonds and
exchange rate between EUR and USD appeared to have significant
explanatory power over these futures contracts on EEX.
Abstract: Triglycerides and their derivatives are considered as viable alternatives for diesel fuels. Rice bran oil is used as diesel fuel. Highly viscous rice bran oil can be reduced by blending it with diesel fuel. The present research is aimed to investigate experimentally the performance, exhaust emission and combustion characteristics of a direct injection (DI) diesel engine, typically used in agricultural sector, over the entire load range when fuelled with rice bran oil and diesel fuel blends, RB10 (10% rice bran oil + 90% diesel fuel) to RB50. The performance, emission and combustion parameters of RB20 were found to be very close to neat diesel fuel (ND). The injector opening pressure (IOP) undoubtedly is of prime importance in diesel engine operation. Performance, emission and combustion characteristics with RB30 at enhanced IOPs are better than ND. Improved premixed heat release rate were noticed with RB30 when the IOP is enhanced.
Abstract: The development and application of wind power for
renewable energy has attracted growing interest in recent years. Renewable energy sources are attracting much alteration as they can
reduce both environmental damage and dependence on fossil fuels. With the growing need for sustainable energy supplies, a case is made
for decentralized, stand-alone power supplies (SAPS) as an alternative to power grids. In the era which traditional petroleum energy resource
decreasing and the green house affect significant increasing, the development and usage of regenerative resources is inevitable. Due to the contribution of the pioneers, the development of regenerative resources already has a remarkable achievement; however, in the view of economy and quantity, it is still a long road for regenerative energy
to replace traditional petroleum energy. In our prospective, in stead of
investigate larger regenerative energy equipment, it is much wiser to
think about the blind side and breakthrough of the current technique.
Abstract: Support Vector Machine (SVM) is a statistical
learning tool that was initially developed by Vapnik in 1979 and later
developed to a more complex concept of structural risk minimization
(SRM). SVM is playing an increasing role in applications to
detection problems in various engineering problems, notably in
statistical signal processing, pattern recognition, image analysis, and
communication systems. In this paper, SVM was applied to the
detection of SAR (synthetic aperture radar) images in the presence of
partially developed speckle noise. The simulation was done for single
look and multi-look speckle models to give a complete overlook and
insight to the new proposed model of the SVM-based detector. The
structure of the SVM was derived and applied to real SAR images
and its performance in terms of the mean square error (MSE) metric
was calculated. We showed that the SVM-detected SAR images have
a very low MSE and are of good quality. The quality of the
processed speckled images improved for the multi-look model.
Furthermore, the contrast of the SVM detected images was higher
than that of the original non-noisy images, indicating that the SVM
approach increased the distance between the pixel reflectivity levels
(the detection hypotheses) in the original images.
Abstract: Collected data must be organized to be utilized efficiently, and hierarchical classification of data is efficient approach to organize data. When data is classified to multiple categories or annotated with a set of labels, users request multi-labeled data by giving a set of labels. There are several interpretations of the data expressed by a set of labels. This paper discusses which data is expressed by a set of labels by introducing orders for sets of labels and shows that there are four types of orders, which are characterized by whether the labels of expressed data includes every label of the given set of labels within the range of the set. Desirable properties of the orders, data is also expressed by the higher set of labels and different sets of labels express different data, are discussed for the orders.
Abstract: According to investigating impact of complexity of
stereoscopic frame pairs on stereoscopic video coding and
transmission, a new rate control algorithm is presented. The proposed
rate control algorithm is performed on three levels: stereoscopic group
of pictures (SGOP) level, stereoscopic frame (SFrame) level and
frame level. A temporal-spatial frame complexity model is firstly
established, in the bits allocation stage, the frame complexity, position
significance and reference property between the left and right frames
are taken into account. Meanwhile, the target buffer is set according to
the frame complexity. Experimental results show that the proposed
method can efficiently control the bitrates, and it outperforms the fixed
quantization parameter method from the rate distortion perspective,
and average PSNR gain between rate-distortion curves (BDPSNR) is
0.21dB.
Abstract: Hyperglycaemia is a key factor that contributes to the
development of diabetes-related microvascular disease and a major
risk factor for endothelial dysfunction. In the current study, we have
explored glucose-induced abnormal intracellular calcium (Ca2+
i)
homeostasis in mouse microvessel endothelial cells (MMECs) in
high glucose (HG) (40mmol/L) versus control (low glucose, LG) (11
mmol/L). We demonstrated that the exposure of MMECs to HG for 3
days did not change basal Ca2+
i, however, there was a significant
increase of acetylcholine-induced Ca2+ entry. Western blots
illustrated that exposure to HG also increased STIM1 (Stromal
Interaction Molecule 1), but not Orai1 (the pore forming subunit),
protein expression levels. Although the link between HG-induced
changes in STIM1 expression, enhanced Ca2+ entry and endothelial
dysfunction requires further study, the current data are suggestive
that targeting these pathways may reduce the impact of HG on
endothelial function.
Abstract: Various solar energy technologies exist and they have
different application techniques in the generation of electrical power.
The widespread use of photovoltaic (PV) modules in such
technologies has been limited by relatively high costs and low
efficiencies. The efficiency of PV panels decreases as the operating
temperatures increase. This is due to the affect of solar intensity and
ambient temperature. In this work, Computational Fluid Dynamics
(CFD) was used to model the heat transfer from a standard PV panel
and thus determine the rate of dissipation of heat. To accurately
model the specific climatic conditions of the United Arab Emirates
(UAE), a case study of a new build green building in Dubai was
used. A finned heat pipe arrangement is proposed and analyzed to
determine the improved heat dissipation and thus improved
performance efficiency of the PV panel. A prototype of the
arrangement is built for experimental testing to validate the CFD
modeling and proof of concept.
Abstract: The fault current levels through the electric devices
have a significant impact on failure probability. New fault current
results in exceeding the rated capacity of circuit breaker and switching
equipments and changes operation characteristic of overcurrent relay.
In order to solve these problems, SFCL (Superconducting Fault
Current Limiter) has rising as one of new alternatives so as to improve
these problems. A fault current reduction differs depending on
installed location. Therefore, a location of SFCL is very important.
Also, SFCL decreases the fault current, and it prevents surrounding
protective devices to be exposed to fault current, it then will bring a
change of reliability. In this paper, we propose method which
determines the optimal location when SFCL is installed in power
system. In addition, the reliability about the power system which
SFCL was installed is evaluated. The efficiency and effectiveness of
this method are also shown by numerical examples and the reliability
indices are evaluated in this study at each load points. These results
show a reliability change of a system when SFCL was installed.
Abstract: The changing economic climate has made global
manufacturing a growing reality over the last decade, forcing
companies from east and west and all over the world to
collaborate beyond geographic boundaries in the design,
manufacture and assemble of products. The ISO10303 and
ISO14649 Standards (STEP and STEP-NC) have been
developed to introduce interoperability into manufacturing
enterprises so as to meet the challenge of responding to
production on demand. This paper describes and illustrates a
STEP compliant CAD/CAPP/CAM System for the manufacture
of rotational parts on CNC turning centers. The information
models to support the proposed system together with the data
models defined in the ISO14649 standard used to create the NC
programs are also described. A structured view of a STEP
compliant CAD/CAPP/CAM system framework supporting the
next generation of intelligent CNC controllers for turn/mill
component manufacture is provided. Finally a proposed
computational environment for a STEP-NC compliant system
for turning operations (SCSTO) is described. SCSTO is the
experimental part of the research supported by the specification
of information models and constructed using a structured
methodology and object-oriented methods. SCSTO was
developed to generate a Part 21 file based on machining
features to support the interactive generation of process plans
utilizing feature extraction. A case study component has been
developed to prove the concept for using the milling and turning
parts of ISO14649 to provide a turn-mill CAD/CAPP/CAM
environment.
Abstract: The focus of this paper is to construct daily time series
exchange rate forecast models of Samoan Tala/USD and Tala/AUD
during the year 2008 to 2012 with neural network The performance
of the models was measured by using varies error functions such as
Root Square mean error (RSME), Mean absolute error (MAE), and
Mean absolute percentage error (MAPE). Our empirical findings
suggest that AR (1) model is an effective tool to forecast the
Tala/USD and Tala/AUD.
Abstract: The performance of modified Fenton (MF) treatment
to promote PAH oxidation in artificially contaminated soil was
investigated in packed soil column with a hydrogen peroxide (H2O2)
delivery system simulating in situ injection. Soil samples were spiked
with phenanthrene (low molecular weight PAH) and fluoranthene
(high molecular weight PAH) to an initial concentration of 500
mg/kg dried soil each. The effectiveness of process parameters
H2O2/soil, iron/soil, chelating agent/soil weight ratios and reaction
time were studied using a 24 three level factorial design experiments.
Statistically significant quadratic models were developed using
Response Surface Methodology (RSM) for degrading PAHs from the
soil samples. Optimum operating condition was achieved at mild
range of H2O2/soil, iron/soil and chelating agent/soil weight ratios,
indicating cost efficient method for treating highly contaminated
lands.