Abstract: Three novel and significant contributions are made in
this paper Firstly, non-recursive formulation of Haar connection
coefficients, pioneered by the present authors is presented, which
can be computed very efficiently and avoid stack and memory
overflows. Secondly, the generalized approach for state analysis of
singular bilinear time-invariant (TI) and time-varying (TV) systems
is presented; vis-˜a-vis diversified and complex works reported by
different authors. Thirdly, a generalized approach for parameter
estimation of bilinear TI and TV systems is also proposed. The unified
framework of the proposed method is very significant in that the
digital hardware once-designed can be used to perform the complex
tasks of state analysis and parameter estimation of different types
of bilinear systems single-handedly. The simplicity, effectiveness and
generalized nature of the proposed method is established by applying
it to different types of bilinear systems for the two tasks.
Abstract: Freeze concentration freezes or crystallises the water
molecules out as ice crystals and leaves behind a highly concentrated
solution. In conventional suspension freeze concentration where ice
crystals formed as a suspension in the mother liquor, separation of
ice is difficult. The size of the ice crystals is still very limited which
will require usage of scraped surface heat exchangers, which is very
expensive and accounted for approximately 30% of the capital cost.
This research is conducted using a newer method of freeze
concentration, which is progressive freeze concentration. Ice crystals
were formed as a layer on the designed heat exchanger surface. In
this particular research, a helical structured copper crystallisation
chamber was designed and fabricated. The effect of two operating
conditions on the performance of the newly designed crystallisation
chamber was investigated, which are circulation flowrate and coolant
temperature. The performance of the design was evaluated by the
effective partition constant, K, calculated from the volume and
concentration of the solid and liquid phase. The system was also
monitored by a data acquisition tool in order to see the temperature
profile throughout the process. On completing the experimental
work, it was found that higher flowrate resulted in a lower K, which
translated into high efficiency. The efficiency is the highest at 1000
ml/min. It was also found that the process gives the highest
efficiency at a coolant temperature of -6 °C.
Abstract: This work is a proposed model of CMOS for which
the algorithm has been created and then the performance evaluation
of this proposition has been done. In this context, another commonly
used model called ZSTT (Zero Switching Time Transient) model is
chosen to compare all the vital features and the results for the
Proposed Equivalent CMOS are promising. In the end, the excerpts
of the created algorithm are also included
Abstract: Bloom filter is a probabilistic and memory efficient
data structure designed to answer rapidly whether an element is
present in a set. It tells that the element is definitely not in the set but
its presence is with certain probability. The trade-off to use Bloom
filter is a certain configurable risk of false positives. The odds of a
false positive can be made very low if the number of hash function is
sufficiently large. For spam detection, weight is attached to each set
of elements. The spam weight for a word is a measure used to rate the
e-mail. Each word is assigned to a Bloom filter based on its weight.
The proposed work introduces an enhanced concept in Bloom filter
called Bin Bloom Filter (BBF). The performance of BBF over
conventional Bloom filter is evaluated under various optimization
techniques. Real time data set and synthetic data sets are used for
experimental analysis and the results are demonstrated for bin sizes 4,
5, 6 and 7. Finally analyzing the results, it is found that the BBF
which uses heuristic techniques performs better than the traditional
Bloom filter in spam detection.
Abstract: Missing data yields many analysis challenges. In case of complex survey design, in addition to dealing with missing data, researchers need to account for the sampling design to achieve useful inferences. Methods for incorporating sampling weights in neural network imputation were investigated to account for complex survey designs. An estimate of variance to account for the imputation uncertainty as well as the sampling design using neural networks will be provided. A simulation study was conducted to compare estimation results based on complete case analysis, multiple imputation using a Markov Chain Monte Carlo, and neural network imputation. Furthermore, a public-use dataset was used as an example to illustrate neural networks imputation under a complex survey design
Abstract: Impurity metals such as manganese and cadmium
from high-tenor cobalt electrolyte solution were selectively removed
by solvent extraction method using Co-D2EHPA after converting the functional group of D2EHPA with Co2+ ions. The process parameters
such as pH, organic concentration, O/A ratio, kinetics etc. were
investigated and the experiments were conducted by batch tests in the laboratory bench scale. Results showed that a significant amount
of manganese and cadmium can be extracted using Co-D2EHPA for the optimum processing of cobalt electrolyte solution at equilibrium pH about 3.5. The McCabe-Thiele diagram, constructed from the
extraction studies showed that 100% impurities can be extracted through four stages for manganese and three stages for cadmium
using O/A ratio of 0.65 and 1.0, respectively. From the stripping study, it was found that 100% manganese and cadmium can be stripped from the loaded organic using 0.4 M H2SO4 in a single
contact. The loading capacity of Co-D2EHPA by manganese and cadmium were also investigated with different O/A ratio as well as
with number of stages of contact of aqueous and organic phases. Valuable information was obtained for the designing of an impurities
removal process for the production of pure cobalt with less trouble in the electrowinning circuit.
Abstract: Group contribution methods such as the UNIFAC are
very useful to researchers and engineers involved in synthesis,
feasibility studies, design and optimization of separation processes.
They can be applied successfully to predict phase equilibrium and
excess properties in the development of chemical and separation
processes. The main focus of this work was to investigate the
possibility of absorbing selected volatile organic compounds (VOCs)
into polydimethylsiloxane (PDMS) using three selected UNIFAC
group contribution methods. Absorption followed by subsequent
stripping is the predominant available abatement technology of
VOCs from flue gases prior to their release into the atmosphere. The
original, modified and effective UNIFAC models were used in this
work. The thirteen selected VOCs that have been considered in this
research are: pentane, hexane, heptanes, trimethylamine, toluene,
xylene, cyclohexane, butyl acetate, diethyl acetate, chloroform,
acetone, ethyl methyl ketone and isobutyl methyl ketone. The
computation was done for solute VOC concentration of 8.55x10-8
which is well in the infinite dilution region. The results obtained in
this study compare very well with those published in literature
obtained through both measurements and predictions. The phase
equilibrium obtained in this study show that PDMS is a good
absorbent for the removal of VOCs from contaminated air streams
through physical absorption.
Abstract: We present a BeeBot, Binus Multi-client Intelligent Telepresence Robot, a custom-build robot system specifically designed for teleconference with multiple person using omni directional actuator. The robot is controlled using a computer networks, so the manager/supervisor can direct the robot to the intended person to start a discussion/inspection. People tracking and autonomous navigation are intelligent features of this robot. We build a web application for controlling the multi-client telepresence robot and open-source teleconference system used. Experimental result presented and we evaluated its performance.
Abstract: In this paper, we combine a probabilistic neural method with radial-bias functions in order to construct the lithofacies of the wells DF01, DF02 and DF03 situated in the Triassic province of Algeria (Sahara). Lithofacies is a crucial problem in reservoir characterization. Our objective is to facilitate the experts' work in geological domain and to allow them to obtain quickly the structure and the nature of lands around the drilling. This study intends to design a tool that helps automatic deduction from numerical data. We used a probabilistic formalism to enhance the classification process initiated by a Self-Organized Map procedure. Our system gives lithofacies, from well-log data, of the concerned reservoir wells in an aspect easy to read by a geology expert who identifies the potential for oil production at a given source and so forms the basis for estimating the financial returns and economic benefits.
Abstract: It has been defined that the “network is the system".
This implies providing levels of service, reliability, predictability and
availability that are commensurate with or better than those that
individual computers provide today. To provide this requires
integrated network management for interconnected networks of
heterogeneous devices covering both the local campus. In this paper
we are addressing a framework to effectively deal with this issue. It
consists of components and interactions between them which are
required to perform the service fault management. A real-world
scenario is used to derive the requirements which have been applied
to the component identification. An analysis of existing frameworks
and approaches with respect to their applicability to the framework is
also carried out.
Abstract: In IETF RFC 2002, Mobile-IP was developed to
enable Laptobs to maintain Internet connectivity while moving
between subnets. However, the packet loss that comes from
switching subnets arises because network connectivity is lost while
the mobile host registers with the foreign agent and this encounters
large end-to-end packet delays. The criterion to initiate a simple and
fast full-duplex connection between the home agent and foreign
agent, to reduce the roaming duration, is a very important issue to be
considered by a work in this paper. State-transition Petri-Nets of the
modeling scenario-based CIA: communication inter-agents procedure
as an extension to the basic Mobile-IP registration process was
designed and manipulated to describe the system in discrete events.
The heuristic of configuration file during practical Setup session for
registration parameters, on Cisco platform Router-1760 using IOS
12.3 (15)T and TFTP server S/W is created. Finally, stand-alone
performance simulations from Simulink Matlab, within each subnet
and also between subnets, are illustrated for reporting better end-toend
packet delays. Results verified the effectiveness of our Mathcad
analytical manipulation and experimental implementation. It showed
lower values of end-to-end packet delay for Mobile-IP using CIA
procedure-based early registration. Furthermore, it reported packets
flow between subnets to improve losses between subnets.
Abstract: The presented work is motivated by a French law
regarding nuclear waste management. A new conceptual Accelerator
Driven System (ADS) designed for the Minor Actinides (MA)
transmutation has been assessed by numerical simulation. The
MUltiple Spallation Target (MUST) ADS combines high thermal power (up to 1.4 GWth) and high specific power. A 30 mA and 1
GeV proton beam is divided into three secondary beams transmitted on three liquid lead-bismuth spallation targets. Neutron and thermalhydraulic
simulations have been performed with the code MURE, based on the Monte-Carlo transport code MCNPX. A methodology has been developed to define characteristic of the MUST ADS concept according to a specific transmutation scenario. The reference
scenario is based on a MA flux (neptunium, americium and curium)
providing from European Fast Reactor (EPR) and a plutonium multireprocessing
strategy is accounted for. The MUST ADS reference
concept is a sodium cooled fast reactor. The MA fuel at equilibrium is mixed with MgO inert matrix to limit the core reactivity and
improve the fuel thermal conductivity. The fuel is irradiated over five
years. Five years of cooling and two years for the fuel fabrication are
taken into account. The MUST ADS reference concept burns about 50% of the initial MA inventory during a complete cycle. In term of
mass, up to 570 kg/year are transmuted in one concept. The methodology to design the MUST ADS and to calculate fuel
composition at equilibrium is precisely described in the paper. A detailed fuel evolution analysis is performed and the reference scenario is compared to a scenario where only americium transmutation is performed.
Abstract: Springback is a significant problem in the sheet metal
forming process. When the tools are released after the stage of
forming, the product springs out, because of the action of the internal
stresses. In many cases the deviation of form is too large and the
compensation of the springback is necessary. The precise prediction
of the springback of product is increasingly significant for the design
of the tools and for compensation because of the higher ratio of the
yield stress to the elastic modulus.
The main object in this paper was to study the effect of the
anisotropy on the springback for three directions of rolling: 0°, 45°
and 90°. At the same time, we highlighted the influence of three
different metallic materials: Aluminum, Steel and Galvanized steel.
The original of our purpose consist on tests which are ensured by
adapting a U-type stretching-bending device on a tensile testing
machine, where we studied and quantified the variation of the
springback according to the direction of rolling. We also showed the
role of lubrication in the reduction of the springback.
Moreover, in this work, we have studied important characteristics
in deep drawing process which is a springback. We have presented
defaults that are showed in this process and many parameters
influenced a springback.
Finally, our results works lead us to understand the influence of
grains orientation with different metallic materials on the springback
and drawing some conclusions how to concept deep drawing tools. In
addition, the conducted work represents a fundamental contribution
in the discussion the industry application.
Abstract: Traditionally, Internet has provided best-effort service to every user regardless of its requirements. However, as Internet becomes universally available, users demand more bandwidth and applications require more and more resources, and interest has developed in having the Internet provide some degree of Quality of Service. Although QoS is an important issue, the question of how it will be brought into the Internet has not been solved yet. Researches, due to the rapid advances in technology are proposing new and more desirable capabilities for the next generation of IP infrastructures. But neither all applications demand the same amount of resources, nor all users are service providers. In this way, this paper is the first of a series of papers that presents an architecture as a first step to the optimization of QoS in the Internet environment as a solution to a SMSE's problem whose objective is to provide public service to internet with certain Quality of Service expectations. The service provides new business opportunities, but also presents new challenges. We have designed and implemented a scalable service framework that supports adaptive bandwidth based on user demands, and the billing based on usage and on QoS. The developed application has been evaluated and the results show that traffic limiting works at optimum and so it does exceeding bandwidth distribution. However, some considerations are done and currently research is under way in two basic areas: (i) development and testing new transfer protocols, and (ii) developing new strategies for traffic improvements based on service differentiation.
Abstract: Careful design and selection of daylighting systems can greatly help in reducing not only artificial lighting use, but also decrease cooling energy consumption and, therefore, potential for downsizing air-conditioning systems. This paper aims to evaluate the energy performance of two types of top-light daylighting systems due to the integration of daylight together with artificial lighting in an existing examinaton hall in University Kebangsaan Malaysia, based on a hot and humid climate. Computer simulation models have been created for building case study (base case) and the two types of toplight daylighting designs for building energy performance evaluation using the VisualDOE 4.0 building energy simulation program. The finding revealed that daylighting through top-light systems is a very beneficial design strategy in reducing annual lighting energy consumption and the overall total annual energy consumption.
Abstract: The quality of short term load forecasting can improve the efficiency of planning and operation of electric utilities. Artificial Neural Networks (ANNs) are employed for nonlinear short term load forecasting owing to their powerful nonlinear mapping capabilities. At present, there is no systematic methodology for optimal design and training of an artificial neural network. One has often to resort to the trial and error approach. This paper describes the process of developing three layer feed-forward large neural networks for short-term load forecasting and then presents a heuristic search algorithm for performing an important task of this process, i.e. optimal networks structure design. Particle Swarm Optimization (PSO) is used to develop the optimum large neural network structure and connecting weights for one-day ahead electric load forecasting problem. PSO is a novel random optimization method based on swarm intelligence, which has more powerful ability of global optimization. Employing PSO algorithms on the design and training of ANNs allows the ANN architecture and parameters to be easily optimized. The proposed method is applied to STLF of the local utility. Data are clustered due to the differences in their characteristics. Special days are extracted from the normal training sets and handled separately. In this way, a solution is provided for all load types, including working days and weekends and special days. The experimental results show that the proposed method optimized by PSO can quicken the learning speed of the network and improve the forecasting precision compared with the conventional Back Propagation (BP) method. Moreover, it is not only simple to calculate, but also practical and effective. Also, it provides a greater degree of accuracy in many cases and gives lower percent errors all the time for STLF problem compared to BP method. Thus, it can be applied to automatically design an optimal load forecaster based on historical data.
Abstract: IEEE 802.16 is a new wireless technology standard, it
has some advantages, including wider coverage, higher bandwidth,
and QoS support. As the new wireless technology for last mile
solution, there are designed two models in IEEE 802.16 standard. One
is PMP (point to multipoint) and the other is Mesh. In this paper we
only focus on IEEE 802.16 Mesh model. According to the IEEE
802.16 standard description, Mesh model has two scheduling modes,
centralized and distributed. Considering the pros and cons of the two
scheduling, we present the combined scheduling QoS framework that
the BS (Base Station) controls time frame scheduling and selects the
shortest path from source to destination directly. On the other hand, we
propose the Expedited Queue mechanism to cut down the transmission
time. The EQ mechanism can reduce a lot of end-to-end delay in our
QoS framework. Simulation study has shown that the average delay is
smaller than contrasts. Furthermore, our proposed scheme can also
achieve higher performance.
Abstract: An attempt has been made to investigate the
machinability of zirconia toughened alumina (ZTA) inserts while
turning AISI 4340 steel. The insert was prepared by powder
metallurgy process route and the machining experiments were
performed based on Response Surface Methodology (RSM) design
called Central Composite Design (CCD). The mathematical model of
flank wear, cutting force and surface roughness have been developed
using second order regression analysis. The adequacy of model has
been carried out based on Analysis of variance (ANOVA) techniques.
It can be concluded that cutting speed and feed rate are the two most
influential factor for flank wear and cutting force prediction. For
surface roughness determination, the cutting speed & depth of cut
both have significant contribution. Key parameters effect on each
response has also been presented in graphical contours for choosing
the operating parameter preciously. 83% desirability level has been
achieved using this optimized condition.
Abstract: Design and implementation of a novel B-ACOSD CFAR algorithm is presented in this paper. It is proposed for detecting radar target in log-normal distribution environment. The BACOSD detector is capable to detect automatically the number interference target in the reference cells and detect the real target by an adaptive threshold. The detector is implemented as a System on Chip on FPGA Altera Stratix II using parallelism and pipelining technique. For a reference window of length 16 cells, the experimental results showed that the processor works properly with a processing speed up to 115.13MHz and processing time0.29 ┬Ás, thus meets real-time requirement for a typical radar system.
Abstract: It is important to remove manganese from water
because of its effects on human and the environment. Human
activities are one of the biggest contributors for excessive manganese
concentration in the environment. The proposed method to remove
manganese in aqueous solution by using adsorption as in carbon
nanotubes (CNT) at different parameters: The parameters are CNT
dosage, pH, agitation speed and contact time. Different pHs are pH
6.0, pH 6.5, pH 7.0, pH 7.5 and pH 8.0, CNT dosages are 5mg,
6.25mg, 7.5mg, 8.75mg or 10mg, contact time are 10 min, 32.5 min,
55 min, 87.5 min and 120 min while the agitation speeds are 100rpm,
150rpm, 200rpm, 250rpm and 300rpm. The parameters chosen for
experiments are based on experimental design done by using Central
Composite Design, Design Expert 6.0 with 4 parameters, 5 levels and
2 replications. Based on the results, condition set at pH 7.0, agitation
speed of 300 rpm, 7.5mg and contact time 55 minutes gives the
highest removal with 75.5%. From ANOVA analysis in Design
Expert 6.0, the residual concentration will be very much affected by
pH and CNT dosage. Initial manganese concentration is 1.2mg/L
while the lowest residual concentration achieved is 0.294mg/L,
which almost satisfy DOE Malaysia Standard B requirement.
Therefore, further experiments must be done to remove manganese
from model water to the required standard (0.2 mg/L) with the initial
concentration set to 0.294 mg/L.