Abstract: The Yasuj city stream named the Beshar supply
water for different usages such as aquaculture farms , drinking,
agricultural and industrial usages. Fish processing plants
,Agricultural farms, waste water of industrial zones and hospitals
waste water which they are generate by human activity produce a
considerable volume of effluent and when they are released in to the
stream they can effect on the water quality and down stream aquatic
systems. This study was conducted to evaluate the effects of outflow
effluent from different human activity and point and non point
pollution sources on the water quality and health of the Beshar
river next to Yasuj. Yasuj is the biggest and most important city in
the Kohkiloye and Boyerahmad province . The Beshar River is one
of the most important aquatic ecosystems in the upstream of the
Karun watershed in south of Iran which is affected by point and non
point pollutant sources . This study was done in order to evaluate the
effects of human activities on the water quality and health of the
Beshar river. This river is approximately 190 km in length and
situated at the geographical positions of 51° 20' to 51° 48' E and 30°
18' to 30° 52' N it is one of the most important aquatic ecosystems of
Kohkiloye and Boyerahmad province in south-west Iran. In this
research project, five study stations were selected to examine water
pollution in the Beshar River systems. Human activity is now one of
the most important factors affecting on hydrology and water quality
of the Beshar river. Humans use large amounts of resources to sustain
various standards of living, although measures of sustainability are
highly variable depending on how sustainability is defined. The
Beshar river ecosystems are particularly sensitive and vulnerable to
human activities. The water samples were analyzed, then some
important water quality parameters such as pH, dissolve oxygen
(DO), Biochemical Oxygen Demand (BOD5), Chemical Oxygen
Demand (COD), Total Suspended Solids (TDS),Turbidity,
Temperature, Nitrates (NO3) and Phosphates (PO4) were estimated
at the two stations. The results show a downward trend in the water
quality at the down stream of the city. The amounts of
BOD5,COD,TSS,T,Turbidity, NO3 and PO4 in the down stream
stations were considerably more than the station 1. By contrast the
amounts of DO in the down stream stations were less than to the
station 1. However when effluent discharge consequence of human
activities are released into the Beshar river near the city, the quality
of river are decreases and the environmental problems of the river
during the next years are predicted to rise.
Abstract: The present investigation was aimed to develop methodology for the standardization of Marichyadi Vati and its raw materials. Standardization was carried using systematic Pharmacognostical and physicochemical parameters as per WHO guidelines. The detailed standardization of Marichyadi Vati, it is concluded that there are no major differences prevailed in the quality of marketed products and laboratory samples of Marichyadi Vati. However, market samples showed slightly better amount of Piperine than the laboratory sample by both methods. This is the first attempt to generate complete set of standards required for the Marichyadi Vati.
Abstract: Since water resources of desert Naein City are very
limited, a approach which saves water resources and meanwhile
meets the needs of the greenspace for water is to use city-s sewage
wastewater. Proper treatment of Naein-s sewage up to the standards
required for green space uses may solve some of the problems of
green space development of the city. The present paper closely
examines available statistics and information associated with city-s
sewage system, and determines complementary stages of sewage
treatment facilities of the city. In the present paper, population, per
capita water use, and required discharge for various greenspace
pieces including different plants are calculated. Moreover, in order to
facilitate the application of water resources, a Crude water
distribution network apart from drinking water distribution network is
designed, and a plan for mixing municipal wells- water with sewage
wastewater in proposed mixing tanks is suggested. Hence, following
greenspace irrigation reform and complementary plan, per capita
greenspace of the city will be increased from current amount of 13.2
square meters to 32 square meters.
Abstract: Many states are now committed to implementing
international human rights standards domestically. In terms of
practical governance, how might effectiveness be measured? A facevalue
answer can be found in domestic laws and institutions relating
to human rights. However, this article provides two further tools to
help states assess their status on the spectrum of robust to fragile
human rights governance. The first recognises that each state has its
own 'human rights history' and the ideal end stage is robust human
rights governance, and the second is developing criteria to assess
robustness. Although a New Zealand case study is used to illustrate
these tools, the widespread adoption of human rights standards by
many states inevitably means that the issues are relevant to other
countries. This is even though there will always be varying degrees of
similarity-difference in constitutional background and developed or
emerging human rights systems.
Abstract: Image coding based on clustering provides immediate
access to targeted features of interest in a high quality decoded
image. This approach is useful for intelligent devices, as well as for
multimedia content-based description standards. The result of image
clustering cannot be precise in some positions especially on pixels
with edge information which produce ambiguity among the clusters.
Even with a good enhancement operator based on PDE, the quality of
the decoded image will highly depend on the clustering process. In
this paper, we introduce an ambiguity cluster in image coding to
represent pixels with vagueness properties. The presence of such
cluster allows preserving some details inherent to edges as well for
uncertain pixels. It will also be very useful during the decoding phase
in which an anisotropic diffusion operator, such as Perona-Malik,
enhances the quality of the restored image. This work also offers a
comparative study to demonstrate the effectiveness of a fuzzy
clustering technique in detecting the ambiguity cluster without losing
lot of the essential image information. Several experiments have been
carried out to demonstrate the usefulness of ambiguity concept in
image compression. The coding results and the performance of the
proposed algorithms are discussed in terms of the peak signal-tonoise
ratio and the quantity of ambiguous pixels.
Abstract: Cloud Computing is an approach that provides computation and storage services on-demand to clients over the network, independent of device and location. In the last few years, cloud computing became a trend in information technology with many companies that transfer their business processes and applications in the cloud. Cloud computing with service oriented architecture has contributed to rapid development of Geographic Information Systems. Open Geospatial Consortium with its standards provides the interfaces for hosted spatial data and GIS functionality to integrated GIS applications. Furthermore, with the enormous processing power, clouds provide efficient environment for data intensive applications that can be performed efficiently, with higher precision, and greater reliability. This paper presents our work on the geospatial data services within the cloud computing environment and its technology. A cloud computing environment with the strengths and weaknesses of the geographic information system will be introduced. The OGC standards that solve our application interoperability are highlighted. Finally, we outline our system architecture with utilities for requesting and invoking our developed data intensive applications as a web service.
Abstract: The growing interest in the issue of intangible assets not only in the scientific community but also in some professional bodies internationally can be explained by several points of view. From the business perspective, enterprises are increasingly motivated by external and internal forces to measure and proactively manage their intangibles. With respect to the issue of intangibles, goodwill has been debated in many countries throughout the world. Despite the numerous efforts and the existence of international accounting standards there is not yet a common accepted accounting treatment for goodwill. This study attempts on the one hand to impress the accounting treatment of goodwill internationally, on the other hand analyses the major subjects in relation to the accounting treatment of goodwill in Greece, since 2005, year where the international accounting standards have been in use for the Greek listed companies. The results indicate that the accounting treatment for the goodwill in Greece, despite the effort for accounting harmonization in Europe from 2005, sustains many differences especially for the no listed companies.
Abstract: The seismic rehabilitation designs of two reinforced
concrete school buildings, representative of a wide stock of similar
edifices designed under earlier editions of the Italian Technical
Standards, are presented in this paper. The mutual retrofit solution
elaborated for the two buildings consists in the incorporation of a
dissipative bracing system including pressurized fluid viscous springdampers
as passive protective devices. The mechanical parameters,
layouts and locations selected for the constituting elements of the
system; the architectural renovation projects developed to properly
incorporate the structural interventions and improve the appearance
of the buildings; highlights of the installation works already
completed in one of the two structures; and a synthesis of the
performance assessment analyses carried out in original and
rehabilitated conditions, are illustrated. The results of the analyses
show a remarkable enhancement of the seismic response capacities of
both structures. This allows reaching the high performance objectives
postulated in the retrofit designs with much lower costs and
architectural intrusion as compared to traditional rehabilitation
interventions designed for the same objectives.
Abstract: Antiseismic property of telecommunication equipment
is very important for the grasp of the damage and the restoration after
earthquake. Telecommunication business operators are regulating
seismic standard for their equipments. These standards are organized
to simulate the real seismic situations and usually define the minimum
value of first natural frequency of the equipments or the allowable
maximum displacement of top of the equipments relative to bottom.
Using the finite element analysis, natural frequency can be obtained
with high accuracy but the relative displacement of top of the
equipments is difficult to predict accurately using the analysis.
Furthermore, in the case of simulating the equipments with access
floor, predicting the relative displacement of top of the equipments
become more difficult.
In this study, using enormous experimental datum, an empirical
formula is suggested to forecast the relative displacement of top of the
equipments. Also it can be known that which physical quantities are
related with the relative displacement.
Abstract: Many corporations are seriously concerned about
security of networks and therefore, their network supervisors are still
reluctant to install WLANs. In this regards, the IEEE802.11i standard
was developed to address the security problems, even though the
mistrust of the wireless LAN technology is still existing. The thought
was that the best security solutions could be found in open standards
based technologies that can be delivered by Virtual Private
Networking (VPN) being used for long time without addressing any
security holes for the past few years. This work, addresses this issue
and presents a simulated wireless LAN of IEEE802.11g protocol, and
analyzes impact of integrating Virtual Private Network technology to
secure the flow of traffic between the client and the server within the
LAN, using OPNET WLAN utility. Two Wireless LAN scenarios
have been introduced and simulated. These are based on normal
extension to a wired network and VPN over extension to a wired
network. The results of the two scenarios are compared and indicate
the impact of improving performance, measured by response time
and load, of Virtual Private Network over wireless LAN.
Abstract: The implementation of Super-Ultra Low Emission
Vehicle standards requires more efficient exhaust gas purification. To
increase the efficiency of exhaust gas purification, an the adsorbent
capable of holding hydrocarbons up to 250-300 ОС should be
developed. The possibility to design such adsorbents by modification
of zeolites of mordenite type, ZSM-5 and NaY, using different
metals cations has been studied.
It has been shown that introducing Cr, Cs, Zn, Ni, Co, Li, Mn in
zeolites results in modification of the toluene TPD and toluene
sorption capacity.
5%LiZSM-5 zeolite exhibits the most attractive TPD curve, with
toluene desorption temperature ranging from 250 to 350ОС. The
sorption capacity of 5%Li-ZSM-5 is 0.4 mmol/g. NaY zeolite has the
highest sorption capacity, up to 2 mmol/g, and holds toluene up to
350ОС, but at 120ОС toluene desorption starts, which is not desirable,
since the adsorbent of cold start hydrocarbons should retain them
until 250-300ОС. Therefore 5%LiZSM-5 zeolite was found to be the
most promising to control the cold-start hydrocarbon emissions
among the samples studied.
Abstract: As computer network technology becomes
increasingly complex, it becomes necessary to place greater
requirements on the validity of developing standards and the
resulting technology. Communication networks are based on large
amounts of protocols. The validity of these protocols have to be
proved either individually or in an integral fashion. One strategy for
achieving this is to apply the growing field of formal methods.
Formal methods research defines systems in high order logic so that
automated reasoning can be applied for verification. In this research
we represent and implement a formerly announced multicast protocol
in Prolog language so that certain properties of the protocol can be
verified. It is shown that by using this approach some minor faults in
the protocol were found and repaired. Describing the protocol as
facts and rules also have other benefits i.e. leads to a process-able
knowledge. This knowledge can be transferred as ontology between
systems in KQML format. Since the Prolog language can increase its
knowledge base every time, this method can also be used to learn an
intelligent network.
Abstract: The demand for new telecommunication services requiring higher capacities, data rates and different operating modes have motivated the development of new generation multi-standard wireless transceivers. A multi-standard design often involves extensive system level analysis and architectural partitioning, typically requiring extensive calculations. In this research, a decimation filter design tool for wireless communication standards consisting of GSM, WCDMA, WLANa, WLANb, WLANg and WiMAX is developed in MATLAB® using GUIDE environment for visual analysis. The user can select a required wireless communication standard, and obtain the corresponding multistage decimation filter implementation using this toolbox. The toolbox helps the user or design engineer to perform a quick design and analysis of decimation filter for multiple standards without doing extensive calculation of the underlying methods.
Abstract: Ethical Education is a compulsorily optional subject in
primary and secondary schools. The Ethical Education objective is
the education of a personality with one´s own identity, with
interiorized ethical standards, with mature moral judgement and
therefore with the behaviour determined by one´s own beliefs; with a
positive attitude to himself/herself and other people and that is why
he/she is able to cooperate and to initiate cooperation. In the paper we
describe the contents and the principles of Ethical education. We also
shows that Ethical education is subject supported primary socialpathological
prevention and education to citizenship. In this context
we try to show that ethical education contributes to the education of
good people who are aware of the necessity to respect social norms
and are able to assume responsibility for their own behaviour in any
situation at present and in the future.
Abstract: In the current Grid environment, efficient workload
management presents a significant challenge, for which there are
exorbitant de facto standards encompassing resource discovery,
brokerage, and data transfer, among others. In addition, the real-time
resource status, essential for an optimal resource allocation strategy,
is often not readily accessible. To address these issues and provide a
cleaner abstraction of the Grid with the potential of generalizing into
arbitrary resource-sharing environment, this paper proposes a new
Condor-based pilot mechanism applied in the PanDA architecture,
PanDA-PF WMS, with the goal of providing a more generic yet
efficient resource allocating strategy. In this architecture, the PanDA
server primarily acts as a repository of user jobs, responding to pilot
requests from distributed, remote resources. Scheduling decisions are
subsequently made according to the real-time resource information
reported by pilots. Pilot Factory is a Condor-inspired solution for a
scalable pilot dissemination and effectively functions as a resource
provisioning mechanism through which the user-job server, PanDA,
reaches out to the candidate resources only on demand.
Abstract: Cantilever L-shaped walls are known to be relatively economical as retaining solution. The design starts by proportioning the wall dimensions for which the stability is checked for. A ratio between the lengths of the base and the stem, falling between 0.5 to 0.7 ensure in most case the stability requirements, however, the displacement pattern of the wall in terms of rotations and translations, and the lateral pressure profile, do not have the same figure for all wall’s proportioning, as it is usually assumed. In the present work the results of a numerical analysis are presented, different wall geometries were considered. The results show that the proportioning governs the equilibrium between the instantaneous rotation and the translation of the wall-toe, also, the lateral pressure estimation based on the average value between the at-rest and the active pressure, recommended by most design standards, is found to be not applicable for all walls.
Abstract: The Institute of Product Development is dealing
with the development, design and dimensioning of micro components
and systems as a member of the Collaborative Research
Centre 499 “Design, Production and Quality Assurance of
Molded micro components made of Metallic and Ceramic Materials".
Because of technological restrictions in the miniaturization
of conventional manufacturing techniques, shape and
material deviations cannot be scaled down in the same proportion
as the micro parts, rendering components with relatively
wide tolerance fields. Systems that include such components
should be designed with this particularity in mind, often requiring
large clearance. On the end, the output of such systems
results variable and prone to dynamical instability. To save
production time and resources, every study of these effects
should happen early in the product development process and
base on computer simulation to avoid costly prototypes. A
suitable method is proposed here and exemplary applied to a
micro technology demonstrator developed by the CRC499. It
consists of a one stage planetary gear train in a sun-planet-ring
configuration, with input through the sun gear and output
through the carrier. The simulation procedure relies on ordinary
Multi Body Simulation methods and subsequently adds
other techniques to further investigate details of the system-s
behavior and to predict its response. The selection of the relevant
parameters and output functions followed the engineering
standards for regular sized gear trains. The first step is to
quantify the variability and to reveal the most critical points of
the system, performed through a whole-mechanism Sensitivity
Analysis. Due to the lack of previous knowledge about the system-s
behavior, different DOE methods involving small and
large amount of experiments were selected to perform the SA.
In this particular case the parameter space can be divided into
two well defined groups, one of them containing the gear-s profile
information and the other the components- spatial location.
This has been exploited to explore the different DOE techniques
more promptly. A reduced set of parameters is derived for
further investigation and to feed the final optimization process,
whether as optimization parameters or as external perturbation
collective. The 10 most relevant perturbation factors and 4 to 6
prospective variable parameters are considered in a new, simplified
model. All of the parameters are affected by the mentioned
production variability. The objective functions of interest
are based on scalar output-s variability measures, so the
problem becomes an optimization under robustness and reliability constrains. The study shows an initial step on the development
path of a method to design and optimize complex micro
mechanisms composed of wide tolerated elements accounting
for the robustness and reliability of the systems- output.
Abstract: After the development of the Internet a suitable
discipline for trading goods electronically has been emerged.
However, this type of markets is not still mature enough in order to
become independent and get closer to seller/buyer-s needs.
Furthermore, the buyable and sellable goods in these markets still
don-t have essential standards for being well-defined. In this paper,
we will present a model for development of a market which can
contain goods with variable definitions and we will also investigate
its characteristics. Besides, by noticing the fact that people have
different discriminations, it-s figured out that the significance of each
attribute of a specific product may vary from different people-s view
points. Consequently we-ll present a model for weighting and
accordingly different people-s view points could be satisfied. These
two aspects will be discussed completely throughout this paper.
Abstract: The move towards internationalization of accounting encountered a great boost, when in 2002 EU delegated the IASB to provide the accounting standards to be applied inside its frontiers. Among the incentives of the standardization of accounting on the international level, is the reduction of the cost of capital. Romania made the move towards IFRS before EU, when the country was not yet a member of it. Even if this made Romania a special case, it was scarcely approached. The leak of real data is usually the reason for avoiding. The novelty of this paper is that it offers an insight from the reality of Romanian companies and their view regarding the IFRS. The paper is based on a survey that the authors made among the companies listed on the first two tiers of the Bucharest Stock Exchange (BSE), which are basically, the most important companies in the country.
Abstract: Transferring patient information between medical care
sites is necessary to deliver better patient care and to reduce medical
cost. So developing of electronic medical records is an important trend
for the world.The Continuity of Care Document (CCD) is product of
collaboration between CDA and CCR standards. In this study, we will
develop a system to generate medical records with entry level based on
CCD template module.