Abstract: The knowledge of biodiesel density over large ranges
of temperature and pressure is important for predicting the behavior
of fuel injection and combustion systems in diesel engines, and for
the optimization of such systems. In this study, cottonseed oil was
transesterified into biodiesel and its density was measured at
temperatures between 288 K and 358 K and pressures between 0.1
MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg⋅m-
3. Experimental pressure-volume-temperature (pVT) cottonseed data
was used along with literature data relative to other 18 biodiesels, in
order to build a database used to test the correlation of density with
temperarure and pressure using the Goharshadi–Morsali–Abbaspour
equation of state (GMA EoS). To our knowledge, this is the first that
density measurements are presented for cottonseed biodiesel under
such high pressures, and the GMA EoS used to model biodiesel
density. The new tested EoS allowed correlations within 0.2 kg·m-3
corresponding to average relative deviations within 0.02%. The built
database was used to develop and test a new full predictive model
derived from the observed linear relation between density and degree
of unsaturation (DU), which depended from biodiesel FAMEs
profile. The average density deviation of this method was only about
3 kg.m-3 within the temperature and pressure limits of application.
These results represent appreciable improvements in the context of
density prediction at high pressure when compared with other
equations of state.
Abstract: The exposure to outdoor air pollution causes lung
cancer and increases the risk of bladder cancer. Because air pollution
in urban areas is mainly caused by transportation, it is necessary to
evaluate pollutant exhaust emissions from vehicles during their realworld
use. Nevertheless their evaluation and reduction is a key
problem, especially in the cities, that account for more than 50% of
world population.
A particular attention was given to the slope variability along the
streets during each journey performed by the instrumented vehicle.
In this paper we dealt with the problem of describing a
quantitatively approach for the reconstruction of GPS coordinates and
altitude, in the context of correlation study between driving cycles /
emission / geographical location, during an experimental campaign
realized with some instrumented cars.
Finally the slope analysis can be correlated to the emission and
consumption values in a specific road position, and it could be
evaluated its influence on their behaviour.
Abstract: The objective of the Economic Dispatch(ED) Problems
of electric power generation is to schedule the committed generating
units outputs so as to meet the required load demand at minimum
operating cost while satisfying all units and system equality and
inequality constraints. This paper presents a new method of ED
problems utilizing the Max-Min Ant System Optimization.
Historically, traditional optimizations techniques have been used,
such as linear and non-linear programming, but within the past
decade the focus has shifted on the utilization of Evolutionary
Algorithms, as an example Genetic Algorithms, Simulated Annealing
and recently Ant Colony Optimization (ACO). In this paper we
introduce the Max-Min Ant System based version of the Ant System.
This algorithm encourages local searching around the best solution
found in each iteration. To show its efficiency and effectiveness, the
proposed Max-Min Ant System is applied to sample ED problems
composed of 4 generators. Comparison to conventional genetic
algorithms is presented.
Abstract: Reduction of CO2 emissions has become a priority for
several countries due to increasing concerns about global warming
and climate change, especially in the developed countries. Residential
sector is considered one of the most important sectors for
considerable reduction of CO2 emissions since it represents a
significant amount of the total consumed energy in those countries. A
significant CO2 reduction cannot be achieved unless some initiatives
have been adopted in the policy of these countries. Introducing micro
combined heat and power (!CHP) systems into residential energy
systems is one of these initiatives, since such a technology offers
several advantages. Moreover, !CHP technology has the opportunity
to be operated not only by natural gas but it could also be operated by
renewable fuels. However, this technology can be operated by
different operation strategies. Each strategy has some advantages and
disadvantages.
This paper provides a review of different operation strategies of
such a technology used for residential energy systems, especially for
single dwellings. The review summarizes key points that outline the
trend of previous research carried out in this field.
Abstract: Renewable energy is derived from natural processes
that are replenished constantly. Included in the definition is
electricity and heat generated from solar, wind, ocean, hydropower,
biomass, geothermal resources, and bio-fuels and hydrogen derived
from renewable resources. Each of these sources has unique
characteristics which influence how and where they are used. This
paper presents the modeling the simulation of solar and hydro hybrid
energy sources in MATLAB/SIMULINK environment. It simulates
all quantities of Hybrid Electrical Power system (HEPS) such as AC
output current of the inverter that injected to the load/grid, load
current, grid current. It also simulates power output from PV and
Hydraulic Turbine Generator (HTG), power delivered to or from grid
and finally power factor of the inverter for PV, HTG and grid. The
proposed circuit uses instantaneous p-q (real-imaginary) power
theory.
Abstract: This experimental study aims at studying the
conversion of macro-algae into bioethanol under several steps of
procedure: preparation, pre-treatment, fermentation, and distillation.
The main objective of this work was to investigate the role of buffer’s
type as a stabiliser of pH level and fermentation time on the yield of
ethanol. For this purpose, experiments were carried out on biomass
macro-algae to de-couple the pre-treatment and fermentation
processes from those associated with distillation process. β-
glucosidase was used as cellulose decomposer during hydrolysis step
and yeast was used during fermentation process. The species of
macro-algae utilised as energy feedstock was Ulva lactuca and it was
harvested from southern coast of Central of Java Island – Indonesia.
Experiments were conducted in a simple fermenter over a different
buffer: citrate buffer and acetic buffer, and over a range of
fermentation times between 5 to 20 days. The ethanol production was
found to be significantly affected by both variables. The optimum
time of fermentation was 10 days with citrate buffer; result in
0.88458% of ethanol, and the ethanol content after distillation
process was shown 0.985015%.
Abstract: Kuosheng nuclear power plant (NPP) is a BWR/6 type
NPP and located on the northern coast of Taiwan. First, Kuosheng
NPP TRACE model were developed in this research. In order to assess
the system response of Kuosheng NPP TRACE model, startup tests
data were used to evaluate Kuosheng NPP TRACE model. Second, the
overpressurization transient analysis of Kuosheng NPP TRACE model
was performed. Besides, in order to confirm the mechanical property
and integrity of fuel rods, FRAPTRAN analysis was also performed in
this study.
Abstract: A noble low NOx combustion technology, based on
partial oxidation combustion concept in a fuel rich combustion zone, is
successfully applied in this research. The burner is designed such that
a portion of fuel is heated and pre-vaporized in the furnace then
injected into a fuel rich combustion zone so that a partial oxidation
reaction occurs. The effects of equivalence ratio, thermal load, and
fuel distribution ratio on the emissions of NOx and CO are
experimentally investigated. This newly developed combustion
technology showed very low NOx emission level, about 12 ppm, when
light oil is used as a fuel.
Abstract: In this paper, the effect of WC-12Co particle
temperature in HVOF thermal spraying process on the coating
thickness has been studied. The statistical results show that the spray
distance and oxygen-to-fuel ratio are effective factors on particle
characterization and thickness of HVOF thermal spraying coatings.
Spray Watch diagnostic system, scanning electron microscopy
(SEM), X-ray diffraction and thickness measuring system were used
for this purpose.
Abstract: This paper presents a new method to design nonlinear
feedback linearization controller for PEMFCs (Polymer Electrolyte
Membrane Fuel Cells). A nonlinear controller is designed based on
nonlinear model to prolong the stack life of PEMFCs. Since it is
known that large deviations between hydrogen and oxygen partial
pressures can cause severe membrane damage in the fuel cell,
feedback linearization is applied to the PEMFC system so that the
deviation can be kept as small as possible during disturbances or load
variations. To obtain an accurate feedback linearization controller,
tuning the linear parameters are always important. So in proposed
study NSGA (Non-Dominated Sorting Genetic Algorithm)-II method
was used to tune the designed controller in aim to decrease the
controller tracking error. The simulation result showed that the
proposed method tuned the controller efficiently.
Abstract: Economic Dispatch (ED) is one of the most
challenging problems of power system since it is difficult to determine
the optimum generation scheduling to meet the particular load demand
with the minimum fuel costs while all constraints are satisfied. The
objective of the Economic Dispatch Problems (EDPs) of electric
power generation is to schedule the committed generating units
outputs so as to meet the required load demand at minimum operating
cost while satisfying all units and system equality and inequality
constraints. In this paper, an efficient and practical steady-state genetic
algorithm (SSGAs) has been proposed for solving the economic
dispatch problem. The objective is to minimize the total generation
fuel cost and keep the power flows within the security limits. To
achieve that, the present work is developed to determine the optimal
location and size of capacitors in transmission power system where,
the Participation Factor Algorithm and the Steady State Genetic
Algorithm are proposed to select the best locations for the capacitors
and determine the optimal size for them.
Abstract: Rice straw pellets are a promising fuel as a renewable
energy source. Financial analysis is needed to make a utilization
system using rise straw pellets financially feasible, considering all
regional conditions including stakeholders related to the collection and
storage, production, transportation and heat utilization. We conducted
the financial analysis of feasibility for a heat utilization system using
rice straw pellets which has been developed for the first time in
Nanporo, Hokkaido, Japan. Especially, we attempted to clarify the
effect of factors required for the system to be financial feasibility, such
as the heating energy demand and collection and storage method of
rice straw. The financial feasibility was found to improve when
increasing the heating energy demand and collecting wheat straw in
August separately from collection of rice straw in November because
the costs of storing rice straw and producing pellets were reduced.
However, the system remained financially unfeasible. This study
proposed a contractor program funded by a subsidy from Nanporo
local government where a contracted company, instead of farmers,
collects and transports rice straw in order to ensure the financial
feasibility of the system, contributing to job creation in the region.
Abstract: The global demand for continuous and eco-friendly
renewable energy as alternative to fossils fuels is large and ever
growing in nowadays. This paper will focus on capability of Vortex
Induced Vibration (VIV) phenomenon in generating alternative
energy for offshore platform application. In order to maximize the
potential of energy generation, the effects of lock in phenomenon and
different geometries of cylinder were studied in this project. VIV is
the motion induced on bluff body which creates alternating lift forces
perpendicular to fluid flow. Normally, VIV is unwanted in order to
prevent mechanical failure of the vibrating structures. But in this
project, instead of eliminating these vibrations, VIV will be exploited
to transform these vibrations into a valuable resource of energy.
Abstract: The fight against climate change and the replacement
of fossil energies nearing exhaustion gradually emerge as major
societal and economic challenges. It is possible to develop common
dates of low commercial value, and put on the local and international
market a new generation of products with high added values such as
bio ethanol. Besides its use in chemical synthesis, bio ethanol can be
blended with gasoline to produce a clean fuel while improving the
octane.
Abstract: The biomass-based fuels have become great concern in order to replace the petroleum-based fuels. Biofuels are a wide range of fuels referred to liquid, gas and solid fuels produced from biomass. Recently, higher chain alcohols such as 3-methyl-1-butanol and isobutanol have become a better candidate compared to bioethanol in order to replace gasoline as transportation fuel. Therefore, in this study, 3-methyl-1-butanol was produced through a fermentation process by yeast. Several types of yeast involved in this research including Saccharomyces cerevisiae, Kluyveromyces lactis GG799 and Pichia pastoris (KM71H, GS115 and X33). The result obtained showed that K. lactis GG799 gave the highest concentration of 3-methyl-1-butanol at 274 mg/l followed by S. cerevisiae, P. pastoris GS115, P. pastoris KM71H and P. pastoris X33 at 265 mg/l, 190 mg/l, 182 mg/l and 174 mg/l respectively. Based on the result, it proved that yeast have a potential in producing 3-methyl-1-butanol naturally.
Abstract: Climate change and poverty are global issues which cannot be waved aside in welfare of the ever increasing population. The causes / consequences are far more elaborate in developing countries, including Nigeria, which poses threats to the existence of man and his environment. The dominant role of agriculture makes it obvious that even minor climate deteriorations can cause devastating socio-economic consequences. Policies to curb the climate change by reducing the consumption of fossil fuels like oil, gas or carbon compounds have significant economical impacts on the producers/suppliers of these fuels. Thus a unified political narrative that advances both agendas is needed, because their components of an environmental coin that needs to be addressed. The developed world should maintain a low-carbon growth & real commitment of 0.7% of gross national income, as aid to developing countries & renewable energy approach should be emphasized, hence global poverty combated.
Abstract: Combustion phenomenon will be accomplished
effectively by the development of low emission combustor. One of the
significant factors influencing the entire Combustion process is the
mixing between a swirling angular jet (Primary Air) and the
non-swirling inner jet (fuel). To study this fundamental flow, the
chamber had to be designed in such a manner that the combustion
process to sustain itself in a continuous manner and the temperature of
the products is sufficiently below the maximum working temperature
in the turbine. This study is used to develop the effective combustion
with low unburned combustion products by adopting the concept of
high swirl flow and motility of holes in the secondary chamber. The
proper selection of a swirler is needed to reduce emission which can be
concluded from the emission of Nox and CO2. The capture of CO2 is
necessary to mitigate CO2 emissions from natural gas. Thus the
suppression of unburned gases is a meaningful objective for the
development of high performance combustor without affecting turbine
blade temperature.
Abstract: The use of biodiesel in conventional diesel engines results in substantial reduction of unburned hydrocarbon, carbon monoxide and particulate matters. The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio engine when fueled with Karanja (Pongamia) methyl ester and its 10-50 % blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of karanja methyl ester as a biofuel has been established in this study. The useful brake power obtained is similar to diesel fuel for all loads. Experiment has been conducted at a fixed engine speed of 1500 rpm, variable load and at compression ratios of 17.5:1 and 18.5:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for pongamia oil methyl ester when compared to that of diesel. The brake thermal efficiency for pongamia oil methyl ester blends and diesel has been calculated and the blend B20 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions. PME as an oxygenated fuel generated more complete combustion, which means increased torque and power. This is also supported with higher thermal efficiencies of the PME blends. NOx is slightly increased due to the higher combustion temperature and the presence of fuel oxygen with the blend at full load. PME as a new Biodiesel and its blends can be used in diesel engines without any engine modification.
Abstract: Biomass is renewable and sustainable. As an energy source, it will not release extra carbon dioxide into the atmosphere. Hence, tremendous efforts have been made to develop technologies capable of transforming biomass into suitable forms of bio-fuel. One of the viable technologies is gasifying biomass in supercritical water (SCW), a green medium for reactions. While previous studies overwhelmingly selected glucose as a model compound for biomass, the present study adopted fructose for the sake of comparison. The gasification of fructose in SCW was investigated experimentally to evaluate the applicability of supercritical water processes to biomass gasification. Experiments were conducted with an autoclave reactor. Gaseous product mainly consists of H2, CO, CO2, CH4 and C2H6. The effect of two major operating parameters, the reaction temperature (673-873 K) and the dosage of oxidizing agent (0-0.5 stoichiometric oxygen), on the product gas composition, yield and heating value was also examined, with the reaction pressure fixed at 25 MPa.
Abstract: This paper presents the findings from a numerical simulation of the flow in 37-rod fuel assembly models spaced by a double-wire trapezoidal wrapping as applied to the BREST-OD-300 experimental nuclear reactor. Data on a high static pressure distribution within the models, and equations for determining the fuel bundle flow friction factors have been obtained. Recommendations are provided on using the closing turbulence models available in the ANSYS Fluent. A comparative analysis has been performed against the existing empirical equations for determining the flow friction factors. The calculated and experimental data fit has been shown.
An analysis into the experimental data and results of the numerical simulation of the BREST-OD-300 fuel rod assembly hydrodynamic performance are presented.