Abstract: In this paper, the noise maps for the area encircled by
the Second Ring Road in Riyadh city are developed based on real
measured data. Sound level meters, GPS receivers to determine
measurement position, a database program to manage the measured
data, and a program to develop the maps are used. A baseline noise
level has been established at each short-term site so subsequent
monitoring may be conducted to describe changes in Riyadh-s noise
environment. Short-term sites are used to show typical daytime and
nighttime noise levels at specific locations by short duration grab
sampling.
Abstract: The need to evaluate and understand the natural
drainage pattern in a flood prone, and fast developing environment is
of paramount importance. This information will go a long way to
help the town planners to determine the drainage pattern, road
networks and areas where prominent structures are to be located. This
research work was carried out with the aim of studying the Bayelsa
landscape topography using digitized topographic information, and to
model the natural drainage flow pattern that will aid the
understanding and constructions of workable drainages. To achieve
this, digitize information of elevation and coordinate points were
extracted from a global imagery map. The extracted information was
modeled into 3D surfaces. The result revealed that the average
elevation for Bayelsa State is 12 m above sea level. The highest
elevation is 28 m, and the lowest elevation 0 m, along the coastline.
In Yenagoa the capital city of Bayelsa were a detail survey was
carried out showed that average elevation is 15 m, the highest
elevation is 25 m and lowest is 3 m above the mean sea level. The
regional elevation in Bayelsa, showed a gradation decrease from the
North Eastern zone to the South Western Zone. Yenagoa showed an
observed elevation lineament, were low depression is flanked by high
elevation that runs from the North East to the South west. Hence,
future drainages in Yenagoa should be directed from the high
elevation, from South East toward the North West and from the
North West toward South East, to the point of convergence which is
at the center that flows from South East toward the North West.
Bayelsa when considered on a regional Scale, the flow pattern is from
the North East to the South West, and also North South. It is
recommended that in the event of any large drainage construction at
municipal scale, it should be directed from North East to the South
West or from North to South. Secondly, detail survey should be
carried out to ascertain the local topography and the drainage pattern
before the design and construction of any drainage system in any part
of Bayelsa.
Abstract: The rapid urbanization of cities has a bane in the form
road accidents that cause extensive damage to life and limbs. A
number of location based factors are enablers of road accidents in the
city. The speed of travel of vehicles is non-uniform among locations
within a city. In this study, the perception of vehicle users is captured
on a 10-point rating scale regarding the degree of variation in speed
of travel at chosen locations in the city. The average rating is used to
cluster locations using fuzzy c-means clustering and classify them as
low, moderate and high speed of travel locations. The high speed of
travel locations can be classified proactively to ensure that accidents
do not occur due to the speeding of vehicles at such locations. The
advantage of fuzzy c-means clustering is that a location may be a
part of more than one cluster to a varying degree and this gives a
better picture about the location with respect to the characteristic
(speed of travel) being studied.
Abstract: In the present paper, disc loaded interaction structure
for potential application in wideband Gyro-TWT amplifier has been
analyzed, taking all the space and modal harmonics into
consideration, for the eigenwave solutions. The analysis has been
restricted to azimuthally symmetric TE0,n mode. Dispersion
characteristics have been plotted by varying the structure parameters
and have been validated against HFSS simulation results. The
variation of eigenvalue with respect to different structure parameters
has also been presented. It has been observed that disc periodicity
plays very important role for wideband operation of disc-loaded
Gyro-TWT.
Abstract: This study was conducted to investigate the incidence
of pathogenic bacteria: Salmonella, Shigella, Escherichia coli O157
and Staphylococcus aureus in cakes and tarts collected from thirtyfive
confectionery producing and selling premises located within
Tripoli city, Libya. The results revealed an incidence of S. aureus
with 94.4 and 48.0 %, E. coli O157 with 14.7 and 4.0 % and Salmonella
sp. with 5.9 and 8.0 % in cakes and tarts samples respectively;
while Shigella was not detected in all samples. In order to determine
the source of these pathogenic bacteria, cotton swabs were taken
from the hands of workers on the production line, the surfaces of
preparation tables and cream whipping instruments. The results
showed that the cotton swabs obtained from the hands of workers
contained S. aureus and Salmonella sp. with an incidence of 42.9 and
2.9 %, the cotton swabs obtained from the surfaces of preparation
tables 22.9 and 2.9 % and the cotton swabs obtained from the cream
whipping instruments 14.3 and 0.0 % respectively; while E. coli
O157 and Shigella sp. were not detected in all swabs. Additionally,
other bacteria were isolated from the hands of workers and the Surfaces
of producing equipments included: Aeromonas sp., Pseudomonas
sp., E. coli, Klebsiella sp., Enterobacter sp., Citrobacter sp.,
Proteus sp., Serratia sp. and Acinetobacter sp. These results indicate
that some of the cakes and tarts might pose threat to consumer's
health. Meanwhile, occurrences of pathogenic bacteria on the hands
of those who are working in production line and the surfaces of
equipments reflect poor hygienic practices at most confectionery
premises examined in this study. Thus, firm and continuous surveillance
of these premises is needed to insure the consumer's health and
safety.
Abstract: The Bangalore City is facing the acute problem of
pollution in the atmosphere due to the heavy increase in the traffic
and developmental activities in recent years. The present study is an
attempt in the direction to assess trend of the ambient air quality
status of three stations, viz., AMCO Batteries Factory, Mysore Road,
GRAPHITE INDIA FACTORY, KHB Industrial Area, Whitefield
and Ananda Rao Circle, Gandhinagar with respect to some of the
major criteria pollutants such as Total Suspended particular matter
(SPM), Oxides of nitrogen (NOx), and Oxides of sulphur (SO2). The
sites are representative of various kinds of growths viz., commercial,
residential and industrial, prevailing in Bangalore, which are
contributing to air pollution. The concentration of Sulphur Dioxide
(SO2) at all locations showed a falling trend due to use of refined
petrol and diesel in the recent years. The concentration of Oxides of
nitrogen (NOx) showed an increasing trend but was within the
permissible limits. The concentration of the Suspended particular
matter (SPM) showed the mixed trend. The correlation between
model and observed values is found to vary from 0.4 to 0.7 for SO2,
0.45 to 0.65 for NOx and 0.4 to 0.6 for SPM. About 80% of data is
observed to fall within the error band of ±50%. Forecast test for the
best fit models showed the same trend as actual values in most of the
cases. However, the deviation observed in few cases could be
attributed to change in quality of petro products, increase in the
volume of traffic, introduction of LPG as fuel in many types of
automobiles, poor condition of roads, prevailing meteorological
conditions, etc.
Abstract: The objective of this work is to investigate the
turbulent reacting flow in a three dimensional combustor with
emphasis on the effect of inlet swirl flow through a numerical
simulation. Flow field is analyzed using the SIMPLE method which is
known as stable as well as accurate in the combustion modeling, and
the finite volume method is adopted in solving the radiative transfer
equation. In this work, the thermal and flow characteristics in a three
dimensional combustor by changing parameters such as equivalence
ratio and inlet swirl angle have investigated. As the equivalence ratio
increases, which means that more fuel is supplied due to a larger inlet
fuel velocity, the flame temperature increases and the location of
maximum temperature has moved towards downstream. In the mean
while, the existence of inlet swirl velocity makes the fuel and
combustion air more completely mixed and burnt in short distance.
Therefore, the locations of the maximum reaction rate and temperature
were shifted to forward direction compared with the case of no swirl.
Abstract: The dramatic increasing of sea-freight container
transportations and the developing trends for using containers in the
multimodal handling systems through the sea, rail, road and land in
nowadays market cause general managers of container terminals to
face challenges such as increasing demand, competitive situation,
new investments and expansion of new activities and need to use new
methods to fulfil effective operations both along quayside and within
the yard. Among these issues, minimizing the turnaround time of
vessels is considered to be the first aim of every container port
system. Regarding the complex structure of container ports, this
paper presents a simulation model that calculates the number of
trucks needed in the Iranian Shahid Rajaee Container Port for
handling containers between the berth and the yard. In this research,
some important criteria such as vessel turnaround time, gantry crane
utilization and truck utilization have been considered. By analyzing
the results of the model, it has been shown that increasing the number
of trucks to 66 units has a significant effect on the performance
indices of the port and can increase the capacity of loading and
unloading up to 10.8%.
Abstract: Complexity, as a theoretical background has made it
easier to understand and explain the features and dynamic behavior
of various complex systems. As the common theoretical background
has confirmed, borrowing the terminology for design from the
natural sciences has helped to control and understand urban
complexity. Phenomena like self-organization, evolution and
adaptation are appropriate to describe the formerly inaccessible
characteristics of the complex environment in unpredictable bottomup
systems. Increased computing capacity has been a key element in
capturing the chaotic nature of these systems.
A paradigm shift in urban planning and architectural design has
forced us to give up the illusion of total control in urban
environment, and consequently to seek for novel methods for
steering the development. New methods using dynamic modeling
have offered a real option for more thorough understanding of
complexity and urban processes. At best new approaches may renew
the design processes so that we get a better grip on the complex
world via more flexible processes, support urban environmental
diversity and respond to our needs beyond basic welfare by liberating
ourselves from the standardized minimalism.
A complex system and its features are as such beyond human
ethics. Self-organization or evolution is either good or bad. Their
mechanisms are by nature devoid of reason. They are common in
urban dynamics in both natural processes and gas. They are features
of a complex system, and they cannot be prevented. Yet their
dynamics can be studied and supported.
The paradigm of complexity and new design approaches has been
criticized for a lack of humanity and morality, but the ethical
implications of scientific or computational design processes have not
been much discussed. It is important to distinguish the (unexciting)
ethics of the theory and tools from the ethics of computer aided
processes based on ethical decisions. Urban planning and architecture
cannot be based on the survival of the fittest; however, the natural
dynamics of the system cannot be impeded on grounds of being
“non-human".
In this paper the ethical challenges of using the dynamic models
are contemplated in light of a few examples of new architecture and
dynamic urban models and literature. It is suggested that ethical
challenges in computational design processes could be reframed
under the concepts of responsibility and transparency.
Abstract: In this paper stress and strain for two rotating thin
wall cylinder fitted together with initial interference and overlap are
computed. Also stress value for variation of initial interference is
calculated.
At first problem is considered without rotation and next angular
velocity increased from 0 to 50000 rev/min and stress in each stage
is calculated. The important point is that when stress become very
small in magnitude the angular velocity is critical and two cylinders
will separate. The critical speed i.e. speed of separation is calculated
in each step.
Abstract: In recent years there has been renewal of interest in the
relation between Green IT and Cloud Computing. The growing use of
computers in cloud platform has caused marked energy consumption,
putting negative pressure on electricity cost of cloud data center. This
paper proposes an effective mechanism to reduce energy utilization in
cloud computing environments. We present initial work on the
integration of resource and power management that aims at reducing
power consumption. Our mechanism relies on recalling virtualization
services dynamically according to user-s virtualization request and
temporarily shutting down the physical machines after finish in order
to conserve energy. Given the estimated energy consumption, this
proposed effort has the potential to positively impact power
consumption. The results from the experiment concluded that energy
indeed can be saved by powering off the idling physical machines in
cloud platforms.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.
Abstract: An advanced composite flywheel rotor consisting of
intra and inter hybrid rims was designed to optimally increase the energy capacity, and was manufactured using filament winding with
in-situ curing. The flywheel has recently attracted considerable attention from many investigators since it possesses great potential in
many energy storage applications, including electric utilities, hybrid or
electric automobiles, and space vehicles. In this investigation, a comprehensive study was conducted with the intent to implement
composites in high performance flywheel applications.The inner two
intra-hybrid rims (rims 1 and 2) were manufactured as a whole part
through continuous filament winding under in-situ curing conditions,
and so were the outer two rims (rims 3 and 4). The outer surface of rim
2 and the inner surface of rim 3 were CNC-tapered for press-fitting. Machined rims were finally press-fitted using a hydraulic press with a
maximum compressive force of approximately 1000 ton.
Abstract: The turbulent mixing of coolant streams of different
temperature and density can cause severe temperature fluctuations in
piping systems in nuclear reactors. In certain periodic contraction
cycles these conditions lead to thermal fatigue. The resulting aging
effect prompts investigation in how the mixing of flows over a sharp
temperature/density interface evolves. To study the fundamental
turbulent mixing phenomena in the presence of density gradients,
isokinetic (shear-free) mixing experiments are performed in a square
channel with Reynolds numbers ranging from 2-500 to 60-000.
Sucrose is used to create the density difference. A Wire Mesh Sensor
(WMS) is used to determine the concentration map of the flow in the
cross section. The mean interface width as a function of velocity,
density difference and distance from the mixing point are analyzed
based on traditional methods chosen for the purposes of
atmospheric/oceanic stratification analyses. A definition of the
mixing layer thickness more appropriate to thermal fatigue and based
on mixedness is devised. This definition shows that the thermal
fatigue risk assessed using simple mixing layer growth can be
misleading and why an approach that separates the effects of large
scale (turbulent) and small scale (molecular) mixing is necessary.
Abstract: Saudi Arabia is an arid country which depends on
costly desalination plants to satisfy the growing residential water
demand. Prediction of water demand is usually a challenging task
because the forecast model should consider variations in economic
progress, climate conditions and population growth. The task is
further complicated knowing that Mecca city is visited regularly by
large numbers during specific months in the year due to religious
occasions. In this paper, a neural networks model is proposed to
handle the prediction of the monthly and yearly water demand for
Mecca city, Saudi Arabia. The proposed model will be developed
based on historic records of water production and estimated visitors-
distribution. The driving variables for the model include annuallyvarying
variables such as household income, household density, and
city population, and monthly-varying variables such as expected
number of visitors each month and maximum monthly temperature.
Abstract: As a result of urbanization, the unpredictable growth of industry and transport, production of chemicals, military activities, etc. the concentration of anthropogenic toxicants spread in nature exceeds all the permissible standards. Most dangerous among these contaminants are organic compounds having great persistence, bioaccumulation, and toxicity along with our awareness of their prominent occurrence in the environment and food chain. Among natural ecological tools, plants still occupying above 40% of the world land, until recently, were considered as organisms having only a limited ecological potential, accumulating in plant biomass and partially volatilizing contaminants of different structure. However, analysis of experimental data of the last two decades revealed the essential role of plants in environment remediation due to ability to carry out intracellular degradation processes leading to partial or complete decomposition of carbon skeleton of different structure contaminants. Though, phytoremediation technologies still are in research and development, their various applications have been successfully used. The paper aims to analyze mechanisms of organic contaminants uptake and detoxification in plants, being the less studied issue in evaluation and exploration of plants potential for environment remediation.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: Developing countries are facing a problem of slums and there appears to be no fool proof solution to eradicate them. For improving the quality of life there are three approaches of slum development and In-situ up-gradation approach is found to be the best one, while the relocation approach has proved to be failure. Factors responsible for failure of relocation projects are needed to be assessed, which is the basic aim of the paper. Factors responsible for failure of relocation projects are loss of livelihood, security of tenure and inefficiency of the Government. These factors are traced out & mapped from the examples of Western & Indian cities. National habitat, Resettlement policy emphasized relationship between shelter and work place. SRA has identified 55 slums for relocation due reservation of land uses, security of tenure and non- notified status of slums. The policy guidelines have been suggested for successful relocation projects. KeywordsLivelihood, Relocation, Slums, Urban poor.
Abstract: The main goal of this paper is to show a possibility, how to solve numerically elliptic boundary value problems arising in 2D linear elasticity by using the fictitious domain method (FDM) and the Total-FETI domain decomposition method. We briefly mention the theoretical background of these methods and demonstrate their performance on a benchmark.
Abstract: In this paper, some practical solid transportation models are formulated considering per trip capacity of each type of conveyances with crisp and rough unit transportation costs. This is applicable for the system in which full vehicles, e.g. trucks, rail coaches are to be booked for transportation of products so that transportation cost is determined on the full of the conveyances. The models with unit transportation costs as rough variables are transformed into deterministic forms using rough chance constrained programming with the help of trust measure. Numerical examples are provided to illustrate the proposed models in crisp environment as well as with unit transportation costs as rough variables.