Abstract: Equipment miniaturisation offers several opportunities such as an increased surface-to-volume ratio and higher heat transfer coefficients. However, moving towards small-diameter channels demands extra attention to fouling, reliability and stable operation of the system. The present investigation explores possibilities to enhance the stability of the once-through micro evaporator by reducing its flow boiling induced pressure fluctuations. Experimental comparison shows that the measured reduction factor approaches a theoretically derived value. Pressure fluctuations are reduced by a factor of ten in the solid conical channel and a factor of 15 in the porous conical channel. This presumably leads to less backflow and therefore to a better flow control.
Abstract: Carrier mobility has become the most important
characteristic of high speed low dimensional devices. Due to
development of very fast switching semiconductor devices, speed of
computer and communication equipment has been increasing day by
day and will continue to do so in future. As the response of any
device depends on the carrier motion within the devices, extensive
studies of carrier mobility in the devices has been established
essential for the growth in the field of low dimensional devices.
Small-signal ac transport of degenerate two-dimensional hot
electrons in GaAs quantum wells is studied here incorporating
deformation potential acoustic, polar optic and ionized impurity
scattering in the framework of heated drifted Fermi-Dirac carrier
distribution. Delta doping is considered in the calculations to
investigate the effects of double delta doping on millimeter and submillimeter
wave response of two dimensional hot electrons in GaAs
nanostructures. The inclusion of delta doping is found to enhance
considerably the two dimensional electron density which in turn
improves the carrier mobility (both ac and dc) values in the GaAs
quantum wells thereby providing scope of getting higher speed
devices in future.
Abstract: Functional imaging procedures for the non-invasive assessment of tissue microcirculation are highly requested, but require a mathematical approach describing the trans- and intercapillary passage of tracer particles. Up to now, two theoretical, for the moment different concepts have been established for tracer kinetic modeling of contrast agent transport in tissues: pharmacokinetic compartment models, which are usually written as coupled differential equations, and the indicator dilution theory, which can be generalized in accordance with the theory of lineartime- invariant (LTI) systems by using a convolution approach. Based on mathematical considerations, it can be shown that also in the case of an open two-compartment model well-known from functional imaging, the concentration-time course in tissue is given by a convolution, which allows a separation of the arterial input function from a system function being the impulse response function, summarizing the available information on tissue microcirculation. Due to this reason, it is possible to integrate the open two-compartment model into the system-theoretic concept of indicator dilution theory (IDT) and thus results known from IDT remain valid for the compartment approach. According to the long number of applications of compartmental analysis, even for a more general context similar solutions of the so-called forward problem can already be found in the extensively available appropriate literature of the seventies and early eighties. Nevertheless, to this day, within the field of biomedical imaging – not from the mathematical point of view – there seems to be a trench between both approaches, which the author would like to get over by exemplary analysis of the well-known model.
Abstract: This study focuses on bureau management
technologies and information systems in developing countries.
Developing countries use such systems which facilitate executive and
organizational functions through the utilization of bureau
management technologies and provide the executive staff with
necessary information.
The concepts of data and information differ from each other in
developing countries, and thus the concepts of data processing and
information processing are different. Symbols represent ideas,
objects, figures, letters and numbers. Data processing system is an
integrated system which deals with the processing of the data related
to the internal and external environment of the organization in order
to make decisions, create plans and develop strategies; it goes
without saying that this system is composed of both human beings
and machines. Information is obtained through the acquisition and
the processing of data. On the other hand, data are raw
communicative messages. Within this framework, data processing
equals to producing plausible information out of raw data.
Organizations in developing countries need to obtain information
relevant to them because rapid changes in the organizational arena
require rapid access to accurate information. The most significant
role of the directors and managers who work in the organizational
arena is to make decisions. Making a correct decision is possible only
when the directors and managers are equipped with sound ideas and
appropriate information. Therefore, acquisition, organization and
distribution of information gain significance. Today-s organizations
make use of computer-assisted “Management Information Systems"
in order to obtain and distribute information.
Decision Support System which is closely related to practice is an
information system that facilitates the director-s task of making
decisions. Decision Support System integrates human intelligence,
information technology and software in order to solve the complex
problems. With the support of the computer technology and software
systems, Decision Support System produces information relevant to
the decision to be made by the director and provides the executive
staff with supportive ideas about the decision.
Artificial Intelligence programs which transfer the studies and
experiences of the people to the computer are called expert systems.
An expert system stores expert information in a limited area and can
solve problems by deriving rational consequences.
Bureau management technologies and information systems in
developing countries create a kind of information society and
information economy which make those countries have their places
in the global socio-economic structure and which enable them to play
a reasonable and fruitful role; therefore it is of crucial importance to
make use of information and management technologies in order to
work together with innovative and enterprising individuals and it is
also significant to create “scientific policies" based on information
and technology in the fields of economy, politics, law and culture.
Abstract: The effect of seed inoculation by VA- mycorrhiza and
different levels of phosphorus fertilizer on growth and yield of
sunflower (Azargol cultivar) was studied in experiment farm of
Islamic Azad University, Karaj Branch during 2008 growing season.
The experiment treatments were arranged in factorial based on a
complete randomized block design with three replications. Four
phosphorus fertilizer levels of 25%, 50% 75% and 100% P
recommended with two levels of Mycorrhiza: with and without
Mycorrhiza (control) were assigned in a factorial combination.
Results showed that head diameter, number of seeds in head, seed
yield and oil yield were significantly higher in inoculated plants than
in non-inoculated plants. Head diameter, number of seeds in head,
1000 seeds weight, biological yield, seed yield and oil yield increased
with increasing P level above 75% P recommended in non-inoculated
plants, whereas no significant difference was observed between 75%
and 100% P recommended. The positive effect of mycorrhizal
inoculation decreased with increasing P levels due to decreased
percent root colonization at higher P levels. According to the results
of this experiment, application of mycorrhiza in present of 50% P
recommended had an appropriate performance and could increase
seed yield and oil production to an acceptable level, so it could be
considered as a suitable substitute for chemical phosphorus fertilizer
in organic agricultural systems.
Abstract: These days wireless local area networks has become
very popular, when the initial IEEE802.11 is the standard for
providing wireless connectivity to automatic machinery, equipment
and stations that require rapid deployment, which may be portable,
handheld or which may be mounted on moving vehicles within a
local area. IEEE802.11 Wireless local area network is a sharedmedium
communication network that transmits information over
wireless links for all IEEE802.11 stations in its transmission range to
receive. When a user is moving from one location to another, how
the other user knows about the required station inside WLAN. For
that we designed and implemented a system to locate a mobile user
inside the wireless local area network based on RSSI with the help of
four specially designed architectures. These architectures are based
on statistical or we can say manual configuration of mapping and
radio map of indoor and outdoor location with the help of available
Sniffer based and cluster based techniques. We found a better
location of a mobile user in WLAN. We tested this work in indoor
and outdoor environments with different locations with the help of
Pamvotis, a simulator for WLAN.
Abstract: Heavy metal pollution is an environmental concern.
Phytoremediation is a low-cost, environmental-friendly approach to
solve this problem. Mustard has the potential in reducing heavy metal
contents in soils. Among mustard (Brassica juncea (L.) Czern &
Coss) genotypes in Sri Lanka, accessions 7788, 8831 and 5088 give
significantly a high yield. Therefore, present study was conducted to
quantify the phytoextractive potential among these local mustard
accessions and to assess the interaction of heavy metals, Pb, Co, Mn
on phytoextraction. A pot experiment was designed with acid washed
sand (quartz) and a series of heavy metal solutions of 0, 25, 50, 75
and 100 μg/g. Experiment was carried out with factorial
experimental design. Mustard accessions were tolerant to heavy
metals and could be successfully used in removal of Pb, Co and Mn
and they are capable of accumulating significant quantities of heavy
metals in vegetative and reproductive organs. The order of the
accumulative potential of Pb, Co and Mn in mustard accessions is,
root > shoot >seed.
Abstract: The heavy metal contamination of the technogenous
sediments and soils at the investigated dump-field show irregular
planar distribution. Also the heavy metal content in the surface water,
drainage water and in the groundwater was studied both in the dry as
well as during the rainy periods. The cementation process causes
substitution of iron by copper. Natural installation and development
of plant species was observed at the old mine waste dumps, specific
to the local chemical conditions such as low content of essential
nutrients and high content of heavy metals. The individual parts of
the plant tissues (roots, branches/stems, leaves/needles, flowers/
fruits) are contaminated by heavy metals and tissues are damaged
differently, respectively.
Abstract: Automated operations based on voice commands will become more and more important in many applications, including robotics, maintenance operations, etc. However, voice command recognition rates drop quite a lot under non-stationary and chaotic noise environments. In this paper, we tried to significantly improve the speech recognition rates under non-stationary noise environments. First, 298 Navy acronyms have been selected for automatic speech recognition. Data sets were collected under 4 types of noisy environments: factory, buccaneer jet, babble noise in a canteen, and destroyer. Within each noisy environment, 4 levels (5 dB, 15 dB, 25 dB, and clean) of Signal-to-Noise Ratio (SNR) were introduced to corrupt the speech. Second, a new algorithm to estimate speech or no speech regions has been developed, implemented, and evaluated. Third, extensive simulations were carried out. It was found that the combination of the new algorithm, the proper selection of language model and a customized training of the speech recognizer based on clean speech yielded very high recognition rates, which are between 80% and 90% for the four different noisy conditions. Fourth, extensive comparative studies have also been carried out.
Abstract: The Model for Knowledge Base of Computational Objects
(KBCO model) has been successfully applied to represent the
knowledge of human like Plane Geometry, Physical, Calculus. However,
the original model cannot easyly apply in inorganic chemistry
field because of the knowledge specific problems. So, the aim of
this article is to introduce how we extend the Computional Object
(Com-Object) in KBCO model, kinds of fact, problems model, and
inference algorithms to develop a program for solving problems
in inorganic chemistry. Our purpose is to develop the application
that can help students in their study inorganic chemistry at schools.
This application was built successful by using Maple, C# and WPF
technology. It can solve automatically problems and give human
readable solution agree with those writting by students and teachers.
Abstract: As computer network technology becomes
increasingly complex, it becomes necessary to place greater
requirements on the validity of developing standards and the
resulting technology. Communication networks are based on large
amounts of protocols. The validity of these protocols have to be
proved either individually or in an integral fashion. One strategy for
achieving this is to apply the growing field of formal methods.
Formal methods research defines systems in high order logic so that
automated reasoning can be applied for verification. In this research
we represent and implement a formerly announced multicast protocol
in Prolog language so that certain properties of the protocol can be
verified. It is shown that by using this approach some minor faults in
the protocol were found and repaired. Describing the protocol as
facts and rules also have other benefits i.e. leads to a process-able
knowledge. This knowledge can be transferred as ontology between
systems in KQML format. Since the Prolog language can increase its
knowledge base every time, this method can also be used to learn an
intelligent network.
Abstract: Because support interference corrections are not properly
understood, engineers mostly rely on expensive dummy measurements
or CFD calculations. This paper presents a method based on uncorrected wind tunnel measurements and fast calculation techniques
(it is a hybrid method) to calculate wall interference, support interference and residual interference (when e.g. a support member
closely approaches the wind tunnel walls) for any type of wind tunnel and support configuration. The method provides with a simple formula
for the calculation of the interference gradient. This gradient is
based on the uncorrected measurements and a successive calculation
of the slopes of the interference-free aerodynamic coefficients. For the latter purpose a new vortex-lattice routine is developed that corrects
the slopes for viscous effects. A test case of a measurement on a wing proves the value of this hybrid method as trends and orders of
magnitudes of the interference are correctly determined.
Abstract: In biological and biomedical research motif finding tools are important in locating regulatory elements in DNA sequences. There are many such motif finding tools available, which often yield position weight matrices and significance indicators. These indicators, p-values and E-values, describe the likelihood that a motif alignment is generated by the background process, and the expected number of occurrences of the motif in the data set, respectively. The various tools often estimate these indicators differently, making them not directly comparable. One approach for comparing motifs from different tools, is computing the E-value as the product of the p-value and the number of possible alignments in the data set. In this paper we explore the combinatorics of the motif alignment models OOPS, ZOOPS, and ANR, and propose a generic algorithm for computing the number of possible combinations accurately. We also show that using the wrong alignment model can give E-values that significantly diverge from their true values.
Abstract: Using the finite element analyses, this paper discusses the effects of temperature-dependent material properties on the stress and temperature fields in a cracked metal plate under the electric current load. The practical and complicated results are obtained when the temperature-dependent material properties are adopted in the analysis. If the simplified (temperature-independent) material properties are used, incorrect results will be obtained.
Abstract: Text data mining is a process of exploratory data
analysis. Classification maps data into predefined groups or classes.
It is often referred to as supervised learning because the classes are
determined before examining the data. This paper describes proposed
radial basis function Classifier that performs comparative crossvalidation
for existing radial basis function Classifier. The feasibility
and the benefits of the proposed approach are demonstrated by means
of data mining problem: direct Marketing. Direct marketing has
become an important application field of data mining. Comparative
Cross-validation involves estimation of accuracy by either stratified
k-fold cross-validation or equivalent repeated random subsampling.
While the proposed method may have high bias; its performance
(accuracy estimation in our case) may be poor due to high variance.
Thus the accuracy with proposed radial basis function Classifier was
less than with the existing radial basis function Classifier. However
there is smaller the improvement in runtime and larger improvement
in precision and recall. In the proposed method Classification
accuracy and prediction accuracy are determined where the
prediction accuracy is comparatively high.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: The research titled “Developing of Thai Classical Music Ensemble in Rattanakosin Period" aimed 1) to study the history of Thai Classical Music Ensemble in Rattanakosin Period and 2) to analyze changing in each period of Rattanakosin Era. This is the historical and documentary research. The data was collected by in-depth interview those musicians, and academic music experts and field study. The focus group discussion was conducted to analyze and conclude the findings. The research found that the history of Thai Classical Music Ensemble in Rattanakosin Period derived from the Ayutthaya period. Thai classical music ensemble consisted of “Wong Pipat", “Wong Mahori", “Wong Kreang Sai". “Wong Kubmai", “Wong Krongkak", “Brass Band", and “Kan Band" which were used to ceremony, ritual, drama, performs and entertainment. Changed of the Thai music in the early Rattanakosin Period were passed from the Ayutthaya Period and the influence of the western civilization. New Band formed in Thai Music were “Orchestra" and “Contemporary Band". The role of Thai music was changed from the ceremonial rituals to entertainment. Development of the Thai music during the reign of King Rama 1 to King Rama 7, was improved from the court. But after the revolution, the musical patronage of the court was maintained by the Government. Thai Classical Music Ensemble were performed to be standard pattern.
Abstract: The mixing behaviors of dry and wet granular
materials in gas fluidized bed systems were investigated
computationally using the combined Computational Fluid Dynamics
and Discrete Element Method (CFD-DEM). Dry particles were
observed to mix fairly rapidly during the fluidization process due to
vigorous relative motions between particles induced by the flow of
gas. In contrast, due to the presence of strong cohesive forces arising
from capillary liquid bridges between wet particles, the mixing
efficiencies of wet granular materials under similar operating
conditions were observed to be reduced significantly.
Abstract: One part of the total employee-s reward is apart from basic wages or salary, employee-s benefits and intangible elements also so called contingent (variable) pay. Contingent pay is connected to performance, contribution, capcompetency or skills of individual employees, and to team-s or company-wide performance or to combination of few of the mentioned possibilities. Main aim of this article is to define, based on available information, contingent pay, describe reasons for its implementation and arguments for and against this type of remuneration, but also bring information not only about its extent and level of utilization by organizations of the Czech Republic operating in the field of environmental protection, but also mention their practical experience with this type of remuneration.
Abstract: In this research, a latent class vector model for pairwise data is formulated. As compared to the basic vector model, this model yields consistent estimates of the parameters since the number of parameters to be estimated does not increase with the number of subjects. The result of the analysis reveals that the model was stable and could classify each subject to the latent classes representing the typical scales used by these subjects.