Abstract: Groundwater is one of the most important water resources in Fars province. Based on this study, 95 percent of the total annual water consumption in Fars is used for agriculture, whereas the percentages for domestic and industrial uses are 4 and 1 percent, respectively. Population growth, urban and industrial growth, and agricultural development in Fars have created a condition of water stress. In this province, farmers and other users are pumping groundwater faster than its natural replenishment rate, causing a continuous drop in groundwater tables and depletion of this resource. In this research variation of groundwater level , their effects and ways to help control groundwater levels in some plains of Fars were evaluated .Excessive exploitation of groundwater in Darab, Jahrom, Estahban, Arsanjan, Khir and Niriz plains of Fars caused the groundwater levels fall too fast or to unacceptable levels. The average drawdown of the water table in Arsanjan, Khir. Estahban and Niriz plain plains were 12,8, 9 and 6 meters during 16,11,11 and 13 years ago respectively. This not only reduces available water resources and well yields but also can saline water intrusion, reductions in river flow and in wetland areas , drying springs, and ground subsidence, considerable increase in pumping costs and a significant decline in crop yields as a result of the increasing salinity. Finally based on situation and condition of the aquifer some suggestions are recommended.
Abstract: The aim of this study was to compare the effects
of an altitude training camp on heart rate variability and
performance in elite triathletes. Ten athletes completed 20 days of live-high, train-low training at 1650m. Athletes
underwent pre and post 800-m swim time trials at sea-level, and two heart rate variability tests at 1650m on the first and
last day of the training camp. Based on their time trial results,
athletes were divided into responders and non-responders. Relative to the non-responders, the responders sympathetic-toparasympathetic
ratio decreased substantially after 20 days of altitude training (-0.68 ± 1.08 and -1.2 ± 0.96, mean ± 90%
confidence interval for supine and standing respectively). In
addition, sympathetic activity while standing was also
substantially lower post-altitude in the responders compared to the non-responders (-1869 ± 4764 ms2). Results indicate that
responders demonstrated a change to more vagal
predominance compared to non-responders.
Abstract: The purpose of this study is comparing and analysing
of the financial characteristics for development methods of the urban development project in the established area, focusing on the
multi-level replotting.
Analysis showed that the type of the lowest expenditure was
'combination type of group-land and multi-level replotting' and the type of the highest profitability was 'multi-level replotting type'. But
'multi-level replotting type' has still risk of amount of cost for the additional architecture. In addition, we subdivided standard amount
for liquidation of replotting and analysed income-expenditure flow.
Analysis showed that both of 'multi-level replotting type' and 'combination type of group-land and multi-level replotting' improved
profitability of project and property change ratio. However, when the
standard was under a certain amount, amount of original property for the replotting was increased exponentially, and profitability of project.
Abstract: Technology of thin film deposition is of interest in
many engineering fields, from electronic manufacturing to corrosion
protective coating. A typical deposition process, like that developed
at the University of Eindhoven, considers the deposition of a thin,
amorphous film of C:H or of Si:H on the substrate, using the
Expanding Thermal arc Plasma technique. In this paper a computing
procedure is proposed to simulate the flow field in a deposition
chamber similar to that at the University of Eindhoven and a
sensitivity analysis is carried out in terms of: precursor mass flow
rate, electrical power, supplied to the torch and fluid-dynamic
characteristics of the plasma jet, using different nozzles. To this
purpose a deposition chamber similar in shape, dimensions and
operating parameters to the above mentioned chamber is considered.
Furthermore, a method is proposed for a very preliminary evaluation
of the film thickness distribution on the substrate. The computing
procedure relies on two codes working in tandem; the output from
the first code is the input to the second one. The first code simulates
the flow field in the torch, where Argon is ionized according to the
Saha-s equation, and in the nozzle. The second code simulates the
flow field in the chamber. Due to high rarefaction level, this is a
(commercial) Direct Simulation Monte Carlo code. Gas is a mixture
of 21 chemical species and 24 chemical reactions from Argon plasma
and Acetylene are implemented in both codes. The effects of the
above mentioned operating parameters are evaluated and discussed
by 2-D maps and profiles of some important thermo-fluid-dynamic
parameters, as per Mach number, velocity and temperature. Intensity,
position and extension of the shock wave are evaluated and the
influence of the above mentioned test conditions on the film
thickness and uniformity of distribution are also evaluated.
Abstract: This research focus on the intrusion detection system (IDS) development which using artificial immune system (AIS) with population based incremental learning (PBIL). AIS have powerful distinguished capability to extirpate antigen when the antigen intrude into human body. The PBIL is based on past learning experience to adjust new learning. Therefore we propose an intrusion detection system call PBIL-AIS which combine two approaches of PBIL and AIS to evolution computing. In AIS part we design three mechanisms such as clonal selection, negative selection and antibody level to intensify AIS performance. In experimental result, our PBIL-AIS IDS can capture high accuracy when an intrusion connection attacks.
Abstract: Over last two decades, due to hostilities of environment
over the internet the concerns about confidentiality of information
have increased at phenomenal rate. Therefore to safeguard the information
from attacks, number of data/information hiding methods have
evolved mostly in spatial and transformation domain.In spatial domain
data hiding techniques,the information is embedded directly on
the image plane itself. In transform domain data hiding techniques the
image is first changed from spatial domain to some other domain and
then the secret information is embedded so that the secret information
remains more secure from any attack. Information hiding algorithms
in time domain or spatial domain have high capacity and relatively
lower robustness. In contrast, the algorithms in transform domain,
such as DCT, DWT have certain robustness against some multimedia
processing.In this work the authors propose a novel steganographic
method for hiding information in the transform domain of the gray
scale image.The proposed approach works by converting the gray
level image in transform domain using discrete integer wavelet
technique through lifting scheme.This approach performs a 2-D
lifting wavelet decomposition through Haar lifted wavelet of the cover
image and computes the approximation coefficients matrix CA and
detail coefficients matrices CH, CV, and CD.Next step is to apply the
PMM technique in those coefficients to form the stego image. The
aim of this paper is to propose a high-capacity image steganography
technique that uses pixel mapping method in integer wavelet domain
with acceptable levels of imperceptibility and distortion in the cover
image and high level of overall security. This solution is independent
of the nature of the data to be hidden and produces a stego image
with minimum degradation.
Abstract: Planning of economic activities development has various dimensions one of which determines adequate capacity of economic activities in provinces regarding the government-s goals. Paralleling planning goals of economic activities development including subjects being focused on the view statement is effective to better realize the statement's goals. Current paper presents a native framework for economic activities development in provincial level. Triple steps within the framework are concordant with the view statement-s goals achievement. At first step of the proposed framework, economic activities are being prioritized in terms of employment indices, and secondly economic activities regarding to the province's relative advantages are being recognized. In the third step, desirable capacity of economic activities is determined with regards to the government's goals and effective constraints in economic activities development. Development of economic activities related to the provinces- relative advantages, contributes on regional balance and on equal development of economic activities. Furthermore, results of the framework enable more confident investment, affect employment development and remove unemployment concern as the main goals of the view statement.
Abstract: To meet the demands of wireless sensor networks
(WSNs) where data are usually aggregated at a single source prior to
transmitting to any distant user, there is a need to establish a tree
structure inside any given event region. In this paper , a novel
technique to create one such tree is proposed .This tree preserves the
energy and maximizes the lifetime of event sources while they are
constantly transmitting for data aggregation. The term Decentralized
Lifetime Maximizing Tree (DLMT) is used to denote this tree.
DLMT features in nodes with higher energy tend to be chosen as data
aggregating parents so that the time to detect the first broken tree link
can be extended and less energy is involved in tree maintenance. By
constructing the tree in such a way, the protocol is able to reduce the
frequency of tree reconstruction, minimize the amount of data loss
,minimize the delay during data collection and preserves the energy.
Abstract: Telemedicine is brought to life by contemporary changes of our world and summarizes the entire range of services that are at the crossroad of traditional healthcare and information technology. It is believed that eHealth can help in solving critical issues of rising costs, care for ageing and housebound population, staff shortage. It is a feasible tool to provide routine as well as specialized health service as it has the potential to improve both the access to and the standard of care. eHealth is no more an optional choice. It has already made quite a way but it still remains a fantastic challenge for the future requiring cooperation and coordination at all possible levels. The strategic objectives of this paper are: 1. To start with an attempt to clarify the mass of terms used nowadays; 2. To answer the question “Who needs eHealth"; 3. To focus on the necessity of bridging telemedicine and medical (health) informatics as well as on the dual relationship between them; as well as 4. To underline the need of networking in understanding, developing and implementing eHealth.
Abstract: A laboratory study on the influence of compactive
effort on expansive black cotton specimens treated with up to 8%
ordinary Portland cement (OPC) admixed with up to 8% bagasse ash
(BA) by dry weight of soil and compacted using the energies of the
standard Proctor (SP), West African Standard (WAS) or
“intermediate” and modified Proctor (MP) were undertaken. The
expansive black cotton soil was classified as A-7-6 (16) or CL using
the American Association of Highway and Transportation Officials
(AASHTO) and Unified Soil Classification System (USCS),
respectively. The 7day unconfined compressive strength (UCS)
values of the natural soil for SP, WAS and MP compactive efforts are
286, 401 and 515kN/m2 respectively, while peak values of 1019,
1328 and 1420kN/m2 recorded at 8% OPC/ 6% BA, 8% OPC/ 2% BA
and 6% OPC/ 4% BA treatments, respectively were less than the
UCS value of 1710kN/m2 conventionally used as criterion for
adequate cement stabilization. The soaked California bearing ratio
(CBR) values of the OPC/BA stabilized soil increased with higher
energy level from 2, 4 and 10% for the natural soil to Peak values of
55, 18 and 8% were recorded at 8% OPC/4% BA 8% OPC/2% BA
and 8% OPC/4% BA, treatments when SP, WAS and MP compactive
effort were used, respectively. The durability of specimens was
determined by immersion in water. Soils treatment at 8% OPC/ 4%
BA blend gave a value of 50% resistance to loss in strength value
which is acceptable because of the harsh test condition of 7 days
soaking period specimens were subjected instead of the 4 days
soaking period that specified a minimum resistance to loss in strength
of 80%. Finally An optimal blend of is 8% OPC/ 4% BA is
recommended for treatment of expansive black cotton soil for use as
a sub-base material.
Abstract: The objective of the paper is to develop the forecast
model for the HW flows. The methodology of the research included
6 modules: historical data, assumptions, choose of indicators, data
processing, and data analysis with STATGRAPHICS, and forecast
models. The proposed methodology was validated for the case study
for Latvia. Hypothesis on the changes in HW for time period of
2010-2020 have been developed and mathematically described with
confidence level of 95.0% and 50.0%. Sensitivity analysis for the
analyzed scenarios was done. The results show that the growth of
GDP affects the total amount of HW in the country. The total amount
of the HW is projected to be within the corridor of – 27.7% in the
optimistic scenario up to +87.8% in the pessimistic scenario with
confidence level of 50.0% for period of 2010-2020. The optimistic
scenario has shown to be the least flexible to the changes in the GDP
growth.
Abstract: Interaction effects of xanthan gum (XG), carboxymethyl
cellulose (CMC), and locust bean gum (LBG) on the flow properties
of oil-in-water emulsions were investigated by a mixture design
experiment. Blends of XG, CMC and LBG were prepared according
to an augmented simplex-centroid mixture design (10 points) and used
at 0.5% (wt/wt) in the emulsion formulations. An appropriate
mathematical model was fitted to express each response as a function
of the proportions of the blend components that are able to
empirically predict the response to any blend of combination of the
components. The synergistic interaction effect of the ternary
XG:CMC:LBG blends at approximately 33-67% XG levels was
shown to be much stronger than that of the binary XG:LBG blend at
50% XG level (p < 0.05). Nevertheless, an antagonistic interaction
effect became significant as CMC level in blends was more than 33%
(p < 0.05). Yield stress and apparent viscosity (at 10 s-1) responses
were successfully fitted with a special quartic model while flow
behaviour index and consistency coefficient were fitted with a full
quartic model (R2
adjusted ≥ 0.90). This study found that a mixture
design approach could serve as a valuable tool in better elucidating
and predicting the interaction effects beyond the conventional twocomponent
blends.
Abstract: This paper describes a practical approach to design
and develop a hybrid learning with acceleration feedback control
(HLC) scheme for input tracking and end-point vibration suppression
of flexible manipulator systems. Initially, a collocated proportionalderivative
(PD) control scheme using hub-angle and hub-velocity
feedback is developed for control of rigid-body motion of the system.
This is then extended to incorporate a further hybrid control scheme
of the collocated PD control and iterative learning control with
acceleration feedback using genetic algorithms (GAs) to optimize the
learning parameters. Experimental results of the response of the
manipulator with the control schemes are presented in the time and
frequency domains. The performance of the HLC is assessed in terms
of input tracking, level of vibration reduction at resonance modes and
robustness with various payloads.
Abstract: The class of geometric deformable models, so-called
level sets, has brought tremendous impact to medical imagery. In
this paper we present yet another application of level sets to medical
imaging. The method we give here will in a way modify the speed
term in the standard level sets equation of motion. To do so we
build a potential based on the distance and the gradient of the
image we study. In turn the potential gives rise to the force field:
F~F(x, y) = P
∀(p,q)∈I
((x, y) - (p, q)) |ÔêçI(p,q)|
|(x,y)-(p,q)|
2 . The direction
and intensity of the force field at each point will determine the
direction of the contour-s evolution. The images we used to test
our method were produced by the Univesit'e de Sherbrooke-s PET
scanners.
Abstract: In this research, Response Surface Methodology (RSM) is used to investigate the effect of four controllable input variables namely: discharge current, pulse duration, pulse off time and applied voltage Surface Roughness (SR) of on Electrical Discharge Machined surface. To study the proposed second-order polynomial model for SR, a Central Composite Design (CCD) is used to estimation the model coefficients of the four input factors, which are alleged to influence the SR in Electrical Discharge Machining (EDM) process. Experiments were conducted on AISI D2 tool steel with copper electrode. The response is modeled using RSM on experimental data. The significant coefficients are obtained by performing Analysis of Variance (ANOVA) at 5% level of significance. It is found that discharge current, pulse duration, and pulse off time and few of their interactions have significant effect on the SR. The model sufficiency is very satisfactory as the Coefficient of Determination (R2) is found to be 91.7% and adjusted R2-statistic (R2 adj ) 89.6%.
Abstract: The objective of this project is to produce computer
assisted instruction(CAI) for welding and brazing in order to
determine the efficiency of the instruction package and the study
accomplishment of learner by studying through computer assisted
instruction for welding and brazing it was examined through the
target group surveyed from the 30 students studying in the two year
of 5-year-academic program, department of production technology
education, faculty of industrial education and technology, king
mongkut-s university of technology thonburi. The result of the
research indicated that the media evaluated by experts and subject
matter quality evaluation of computer assisted instruction for welding
and brazing was in line for the good criterion. The mean of score
evaluated before the study, during the study and after the study was
34.58, 83.33 and 83.43, respectively. The efficiency of the lesson was
83.33/83.43 which was higher than the expected value, 80/80. The
study accomplishment of the learner, who utilizes computer assisted
instruction for welding and brazing as a media, was higher and equal
to the significance statistical level of 95%. The value was 1.669
which was equal to 35.36>1.669. It could be summarized that
computer assisted instruction for welding and brazing was the
efficient media to use for studying and teaching.
Abstract: Cognitive Dissonance can be conceived both as a concept related to the tendency to avoid internal contradictions in certain situations, and as a higher order theory about information processing in the human mind. In the last decades, this last sense has been strongly surpassed by the former, as nearly all experiment on the matter discuss cognitive dissonance as an output of motivational contradictions. In that sense, the question remains: is cognitive dissonance a process intrinsically associated with the way that the mind processes information, or is it caused by such specific contradictions? Objective: To evaluate the effects of cognitive dissonance in the absence of rewards or any mechanisms to manipulate motivation. Method: To solve this question, we introduce a new task, the hypothetical social arrays paradigm, which was applied to 50 undergraduate students. Results: Our findings support the perspective that the human mind shows a tendency to avoid internal dissonance even when there are no rewards or punishment involved. Moreover, our findings also suggest that this principle works outside the conscious level.
Abstract: Age at first marriage is a basic temporal term that is
culturally constructed for marriage relationship between an adult
male and an adult female intended to have sex, to reproduce and to
adapt to environment from one generation to another around the
world. Cross-cultural evidences suggest that age at first marriage for
both male and female not only varies across the cultures, but also
varies among the subcultures of the same society. The purpose of the
study was to compare age at first marriage for husband and wife
including age differences between them between Muslim and Santal
communities in rural Bangladesh. For this we hypothesized that (1)
there were significant differences in age at first marriage and age
interval between husband and wife between Muslim and Santal
communities in rural Bangladesh. In so doing, 288 couples (145 pairs
of couples for Muslim and 143 pairs of couples for Santal) were
selected by cluster random sampling from the Kalna village situated
in the Tanore Upazila of Rajshahi district, Bangladesh, whose
current mean age range was 36.59 years for husband and 28.85 years
for wife for the Muslim and 31.74 years for husband and 25.21 years
for wife for the Santal respectively. The results of Independent
Sample t test showed that mean age at first marriage for the Muslim
samples was 23.05 years for husbands and 15.11 years for wives,
while mean age at first marriage for the Santal samples was 20.71
years for husbands and 14.34 years for wives respectively that were
significantly different at p0.05) among the selected husbands
and wives between the two communities. This study recommends
that further cross-cultural researches should be done on the causeeffect
relationships between socio-cultural factors and age at
marriage between the two communities in Bangladesh.
Abstract: Since supply chains highly impact the financial
performance of companies, it is important to optimize and analyze
their Key Performance Indicators (KPI). The synergistic combination
of Particle Swarm Optimization (PSO) and Monte Carlo simulation is
applied to determine the optimal reorder point of warehouses in
supply chains. The goal of the optimization is the minimization of the
objective function calculated as the linear combination of holding and
order costs. The required values of service levels of the warehouses
represent non-linear constraints in the PSO. The results illustrate that
the developed stochastic simulator and optimization tool is flexible
enough to handle complex situations.
Abstract: The manufacturing transmission line tower parts has
being generated hazardous waste which is required proper disposal
of waste for protection of land pollution. Manufacturing Process in
the manufacturing of steel angle, plates, pipes, channels are passes
through conventional, semi automatic and CNC machines for
cutting, marking, punching, drilling, notching, bending operations.
All fabricated material Coated with thin layer of Zinc in Galvanizing
plant where molten zinc is used for coating. Prior to Galvanizing,
chemical like 33% concentrated HCl Acid, ammonium chloride and
d-oil being used for pretreatment of iron. The bath of water with
sodium dichromate is used for cooling and protection of the
galvanized steel. For the heating purpose the furnace oil burners are
used. These above process the Zinc dross, Zinc ash, ETP sludge and
waste pickled acid generated as hazardous waste. The RPG has
made captive secured land fill site, since 1997 since then it was
using for disposal of hazardous waste after completion of SLF
(Secured land fill) site. The RPG has raised height from ground
level then now it is being used for disposal of waste as he designed
the SLF after in creasing height of from GL it is functional without
leach ate or adverse impacts in the environment.