Abstract: A human’s hand localization is revised by using radar cross section (RCS) measurements with a minimum root mean square (RMS) error matching algorithm on a touchless keypad mock-up model. RCS and frequency transfer function measurements are carried out in an indoor environment on the frequency ranged from 3.0 to 11.0 GHz to cover federal communications commission (FCC) standards. The touchless keypad model is tested in two different distances between the hand and the keypad. The initial distance of 19.50 cm is identical to the heights of transmitting (Tx) and receiving (Rx) antennas, while the second distance is 29.50 cm from the keypad. Moreover, the effects of Rx angles relative to the hand of human factor are considered. The RCS input parameters are compared with power loss parameters at each frequency. From the results, the performance of the RCS input parameters with the second distance, 29.50 cm at 3 GHz is better than the others.
Abstract: This study aims at being acquainted with the using the
body fat percentage (%BF) with body Mass Index (BMI) as input
parameters in fuzzy logic decision support system to predict properly
the lifted weight for students at weightlifting class lift according to
his abilities instead of traditional manner. The sample included 53
male students (age = 21.38 ± 0.71 yrs, height (Hgt) = 173.17 ± 5.28
cm, body weight (BW) = 70.34 ± 7.87.6 kg, Body mass index (BMI)
23.42 ± 2.06 kg.m-2, fat mass (FM) = 9.96 ± 3.15 kg and fat
percentage (% BF) = 13.98 ± 3.51 %.) experienced the weightlifting
class as a credit and has variance at BW, Hgt and BMI and FM. BMI
and % BF were taken as input parameters in FUZZY logic whereas
the output parameter was the lifted weight (LW). There were
statistical differences between LW values before and after using
fuzzy logic (Diff 3.55± 2.21, P > 0.001). The percentages of the LW
categories proposed by fuzzy logic were 3.77% of students to lift 1.0
fold of their bodies; 50.94% of students to lift 0.95 fold of their
bodies; 33.96% of students to lift 0.9 fold of their bodies; 3.77% of
students to lift 0.85 fold of their bodies and 7.55% of students to lift
0.8 fold of their bodies. The study concluded that the characteristic
changes in body composition experienced by students when
undergoing weightlifting could be utilized side by side with the
Fuzzy logic decision support system to determine the proper
workloads consistent with the abilities of students.
Abstract: By GEO5 FEM program with four rockfill slope
modeling and stability analysis was performed for S1, S2, S3 and
S4 slopes where landslides of the shalefills were limited. Effective
angle of internal friction (φ'°) 17°-22.5°, the effective cohesion (c')
from 0.5 to 1.8 kPa, saturated unit weight 1.78-2.43 g/cm3, natural
unit weight 1.9-2.35 g/cm3, dry unit weight 1.97-2.40 g/cm3, the
permeability coefficient of 1x10-4 - 6.5x10-4 cm/s. In cross-sections
of the slope, GEO 5 FEM program possible critical surface tension
was examined. Rockfill dump design was made to prevent sliding
slopes. Bulk material designated geotechnical properties using also
GEO5 programs FEM and stability program via a safety factor
determined and calculated according to the values S3 and S4 No.
slopes are stable S1 and S2 No. slopes were close to stable state
that has been found to be risk. GEO5 programs with limestone rock
fill dump through FEM program was found to exhibit stability.
Abstract: To increase the temperature contrast in thermal
images, the characteristics of the electrical conductivity and thermal
imaging modalities can be combined. In this experimental study, it is
objected to observe whether the temperature contrast created by the
tumor tissue can be improved just due to the current application
within medical safety limits. Various thermal breast phantoms are
developed to simulate the female breast tissue. In vitro experiments
are implemented using a thermal infrared camera in a controlled
manner. Since experiments are implemented in vitro, there is no
metabolic heat generation and blood perfusion. Only the effects and
results of the electrical stimulation are investigated. Experimental
study is implemented with two-dimensional models. Temperature
contrasts due to the tumor tissues are obtained. Cancerous tissue is
determined using the difference and ratio of healthy and tumor
images. 1 cm diameter single tumor tissue causes almost 40 °mC
temperature contrast on the thermal-breast phantom. Electrode
artifacts are reduced by taking the difference and ratio of background
(healthy) and tumor images. Ratio of healthy and tumor images show
that temperature contrast is increased by the current application.
Abstract: The ductility is an important parameter in the nonlinear behavior of portal structures reinforced concrete. It may be explained by the ability of the structure to deform in the plastic range, or the geometric characteristics in the map may influence the overall ductility. Our study is based on the influence of geometric slenderness (Lx / Ly) on the overall ductility of these structures, a study is made on a structure has 05 floors with varying the column section of 900 cm², 1600 cm² and 1225 cm². A slight variation in global ductility is noticed as (Lx/Ly) varies; however, column sections can control satisfactorily the plastic behavior of buildings.
Abstract: The objective of this research is to mitigate and prevent
the alkali silica reactivity (ASR) in highway construction projects.
ASR is a deleterious reaction initiated when the silica content of the
aggregate reacts with alkali hydroxides in cement in the presence of
relatively high moisture content. The ASR results in the formation of
an expansive white colored gel-like material which forms the
destructive tensile stresses inside hardened concrete. In this research, different types of local aggregates available in the
State of Arkansas were mixed and mortar bars were poured according
to the ASTM specifications. Mortar bars expansion was measured
versus time and aggregates with potential ASR problems were
detected. Different types of supplementary cementitious materials
(SCMs) were used in remixing mortar bars with highly reactive
aggregates. Length changes for remixed bars proved that different
types of SCMs can be successfully used in reducing the expansive
effect of ASR. SCMs percentage by weight is highly dependent on
the SCM type. The result of this study will help avoiding future
losses due to ASR cracking in construction project and reduce the
maintenance, repair, and replacement budgets required for highways
network.
Abstract: While the feature sizes of recent Complementary Metal
Oxid Semiconductor (CMOS) devices decrease the influence of static
power prevails their energy consumption. Thus, power savings that
benefit from Dynamic Frequency and Voltage Scaling (DVFS) are
diminishing and temporal shutdown of cores or other microchip
components become more worthwhile. A consequence of powering off unused parts of a chip is that the
relative difference between idle and fully loaded power consumption
is increased. That means, future chips and whole server systems gain
more power saving potential through power-aware load balancing,
whereas in former times this power saving approach had only
limited effect, and thus, was not widely adopted. While powering
off complete servers was used to save energy, it will be superfluous
in many cases when cores can be powered down. An important
advantage that comes with that is a largely reduced time to respond
to increased computational demand. We include the above developments in a server power model
and quantify the advantage. Our conclusion is that strategies from
datacenters when to power off server systems might be used in the
future on core level, while load balancing mechanisms previously
used at core level might be used in the future at server level.
Abstract: Mumbai, being traditionally the epicenter of India's
trade and commerce, the existing major ports such as Mumbai and
Jawaharlal Nehru Ports (JN) situated in Thane estuary are also
developing its waterfront facilities. Various developments over the
passage of decades in this region have changed the tidal flux
entering/leaving the estuary. The intake at Pir-Pau is facing the
problem of shortage of water in view of advancement of shoreline,
while jetty near Ulwe faces the problem of ship scheduling due to
existence of shallower depths between JN Port and Ulwe Bunder. In
order to solve these problems, it is inevitable to have information
about tide levels over a long duration by field measurements.
However, field measurement is a tedious and costly affair;
application of artificial intelligence was used to predict water levels
by training the network for the measured tide data for one lunar tidal
cycle. The application of two layered feed forward Artificial Neural
Network (ANN) with back-propagation training algorithms such as
Gradient Descent (GD) and Levenberg-Marquardt (LM) was used to
predict the yearly tide levels at waterfront structures namely at Ulwe
Bunder and Pir-Pau. The tide data collected at Apollo Bunder, Ulwe,
and Vashi for a period of lunar tidal cycle (2013) was used to train,
validate and test the neural networks. These trained networks having
high co-relation coefficients (R= 0.998) were used to predict the tide
at Ulwe, and Vashi for its verification with the measured tide for the
year 2000 & 2013. The results indicate that the predicted tide levels
by ANN give reasonably accurate estimation of tide. Hence, the
trained network is used to predict the yearly tide data (2015) for
Ulwe. Subsequently, the yearly tide data (2015) at Pir-Pau was
predicted by using the neural network which was trained with the
help of measured tide data (2000) of Apollo and Pir-Pau. The analysis of measured data and study reveals that: The
measured tidal data at Pir-Pau, Vashi and Ulwe indicate that there is
maximum amplification of tide by about 10-20 cm with a phase lag
of 10-20 minutes with reference to the tide at Apollo Bunder
(Mumbai). LM training algorithm is faster than GD and with increase
in number of neurons in hidden layer and the performance of the
network increases. The predicted tide levels by ANN at Pir-Pau and
Ulwe provides valuable information about the occurrence of high and
low water levels to plan the operation of pumping at Pir-Pau and
improve ship schedule at Ulwe.
Abstract: Magnetic Resonance Imaging Contrast Agents
(MRI-CM) are significant in the clinical and biological imaging as
they have the ability to alter the normal tissue contrast, thereby
affecting the signal intensity to enhance the visibility and detectability
of images. Superparamagnetic Iron Oxide (SPIO) nanoparticles,
coated with dextran or carboxydextran are currently available for
clinical MR imaging of the liver. Most SPIO contrast agents are
T2 shortening agents and Resovist (Ferucarbotran) is one of a
clinically tested, organ-specific, SPIO agent which has a low
molecular carboxydextran coating. The enhancement effect of
Resovist depends on its relaxivity which in turn depends on factors
like magnetic field strength, concentrations, nanoparticle properties,
pH and temperature. Therefore, this study was conducted to
investigate the impact of field strength and different contrast
concentrations on enhancement effects of Resovist. The study
explored the MRI signal intensity of Resovist in the physiological
range of plasma from T2-weighted spin echo sequence at three
magnetic field strengths: 0.47 T (r1=15, r2=101), 1.5 T (r1=7.4,
r2=95), and 3 T (r1=3.3, r2=160) and the range of contrast
concentrations by a mathematical simulation. Relaxivities of r1 and r2
(L mmol-1 Sec-1) were obtained from a previous study and the selected
concentrations were 0.05, 0.06, 0.07, 0.08, 0.09, 0.1, 0.2, 0.3, 0.4, 0.5,
0.6, 0.7, 0.8, 0.9, 1.0, 2.0, and 3.0 mmol/L. T2-weighted images were
simulated using TR/TE ratio as 2000 ms /100 ms. According to the
reference literature, with increasing magnetic field strengths, the
r1 relaxivity tends to decrease while the r2 did not show any
systematic relationship with the selected field strengths. In parallel,
this study results revealed that the signal intensity of Resovist at lower
concentrations tends to increase than the higher concentrations. The
highest reported signal intensity was observed in the low field strength
of 0.47 T. The maximum signal intensities for 0.47 T, 1.5 T and 3 T
were found at the concentration levels of 0.05, 0.06 and 0.05 mmol/L,
respectively. Furthermore, it was revealed that, the concentrations
higher than the above, the signal intensity was decreased
exponentially. An inverse relationship can be found between the field
strength and T2 relaxation time, whereas, the field strength was
increased, T2 relaxation time was decreased accordingly. However,
resulted T2 relaxation time was not significantly different between
0.47 T and 1.5 T in this study. Moreover, a linear correlation of
transverse relaxation rates (1/T2, s–1) with the concentrations of
Resovist can be observed. According to these results, it can conclude
that the concentration of SPIO nanoparticle contrast agents and the
field strengths of MRI are two important parameters which can affect the signal intensity of T2-weighted SE sequence. Therefore, when MR
imaging those two parameters should be considered prudently.
Abstract: This paper presents a fault-tolerant implementation for
adder schemes using the dual duplication code. To prove the
efficiency of the proposed method, the circuit is simulated in double
pass transistor CMOS 32nm technology and some transient faults are
voluntary injected in the Layout of the circuit. This fully differential
implementation requires only 20 transistors which mean that the
proposed design involves 28.57% saving in transistor count
compared to standard CMOS technology.
Abstract: The field of instrumentation electronics is undergoing
an explosive growth, due to its wide range of applications. The
proliferation of electrical devices in a close working proximity can
negatively influence each other’s performance. The degradation in
the performance is due to electromagnetic interference (EMI). This paper investigates the negative effects of electromagnetic
interference originating in the General Purpose Interface Bus (GPIB)
control-network of the AC-DC transfer measurement system.
Remedial measures of reducing measurement errors and failure of
range of industrial devices due to EMI have been explored. The ACDC
transfer measurement system was analysed for the commonmode
(CM) EMI effects. Further investigation of coupling path as
well as much accurate identification of noise propagation mechanism
has been outlined. To prevent the occurrence of common-mode
(ground loops) which was identified between the GPIB system
control circuit and the measurement circuit, a microcontroller-driven
GPIB switching isolator device was designed, prototyped,
programmed and validated. This mitigation technique has been
explored to reduce EMI effectively.
Abstract: This article developed an ion thruster optic system
sputter erosion depth numerical 3D model by IFE-PIC (Immersed
Finite Element-Particle-in-Cell) and Mont Carlo method, and
calculated the downstream surface sputter erosion rate of accelerator
grid; compared with LIPS-200 life test data. The results of the
numerical model are in reasonable agreement with the measured data.
Finally, we predicted the lifetime of the 20cm diameter ion thruster via
the erosion data obtained with the model. The ultimate result
demonstrated that under normal operating condition, the erosion rate
of the grooves wears on the downstream surface of the accelerator grid
is 34.6μm⁄1000h, which means the conservative lifetime until
structural failure occurring on the accelerator grid is 11500 hours.
Abstract: This study investigated the effects of thermal
treatment on Tualang honey sample in terms of honey colour and
heat-induced small metabolites. The heating process was carried out
in a temperature controlled water batch at 90oC for 4 hours. The
honey samples were put in cylinder tubes with the dimension of 1 cm
diameter and 10 cm length for homogenous heat transfer. The results
found that the thermal treatment produced not only
hydroxylmethylfurfural, but also other harmful substances such as
phthalic anhydride and radiolytic byproducts. The degradation of
honey protein was due to the detection of free amino acids such as
cysteine and phenylalanine in heat-treated honey samples. Sugar
dehydration was also occurred because fragmented di-galactose was
identified based on the presence of characteristic ions in the mass
fragmentation pattern. The honey colour was found getting darker as
the heating duration was increased up to 4 hours. Approximately, 60
mm PFund of increment was noticed for the honey colour with the
colour change rate of 14.8 mm PFund per hour. Based on the
principal component analysis, the score plot clearly shows that the
chemical profile of Tualang honey was significantly altered after 2
hours of heating at 90oC.
Abstract: In order to utilize results from global climate models,
dynamical and statistical downscaling techniques have been
developed. For dynamical downscaling, usually a limited area
numerical model is used, with associated high computational cost.
This research proposes dynamic equation for specific space-time
regional climate downscaling from the Educational Global Climate
Model (EdGCM) for Southeast Asia. The equation is for surface air
temperature. This equation provides downscaling values of surface
air temperature at any specific location and time without running a
regional climate model. In the proposed equations, surface air
temperature is approximated from ground temperature, sensible heat
flux and 2m wind speed. Results from the application of the equation
show that the errors from the proposed equations are less than the
errors for direct interpolation from EdGCM.
Abstract: Increase of emergency incidents and crisis situations
requires proactive crisis management of authorities and for its
solution. Application Business Continuity Management helps the
crisis management authorities to quickly and responsibly respond to
threats. It also helps effectively and efficiently planning powers and
resources. The main goal of this article is describing Military
Continuity Management System (MCMS) based on the principles of
Business Continuity Management System (BCMS) for dealing with
floods in the territory of the selected municipalities. There are
explained steps of loading, running and evaluating activities in the
software application MCMS. Software MCMS provides complete
control over the tasks, contribute a comprehensive and responsible
approach solutions to solution floods in the municipality.
Abstract: Ensuring of continuity of business is basic strategy of
every company. Continuity of organization activities includes
comprehensive procedures that help in solving unexpected situations
of natural and anthropogenic character (for example flood, blaze,
economic situations). Planning of continuity operations is a process
that helps identify critical processes and implement plans for the
security and recovery of key processes. The aim of this article is to
demonstrate application of system approach to managing business
continuity called business continuity management systems in military
issues. This article describes the life cycle of business continuity
management which is based on the established cycle PDCA (Plan-
Do-Check-Act). After this is carried out by activities which are
making by University of Defence during activation of forces and
means of the integrated rescue system in case of emergencies -
accidents at a nuclear power plant in Czech Republic. Activities of
various stages of deployment earmarked forces and resources are
managed and evaluated by using MCMS application (Military
Continuity Management System).
Abstract: Gladiolus is an important cash crop and is grown
mainly for its elegant spikes. Traditionally the gladiolus corms are
planted manually which is very tedious, time consuming and labor
intensive operation. So far, there is no planter available for planting
of gladiolus corms. With a view to mechanize the planting operation
of this horticultural crop, a prototype of 4-row gladiolus planter was
developed and its performance was evaluated in-situ condition. Cupchain
type metering device was used to place each single gladiolus
corm in furrow at required spacing while planting. Three levels of
corm spacing viz 15, 20 and 25 cm and four levels of forward speed
viz 1.0, 1.5, 2.0 and 2.5 km/h was taken as evaluation parameter for
the planter. The performance indicators namely corm spacing in each
row, coefficient of uniformity, missing index, multiple index, quality
of feed index, number of corms per meter length, mechanical damage
to the corms etc. were determined during the field test. The data was
statistically analyzed using Completely Randomized Design (CRD)
for testing the significance of the parameters. The result indicated
that planter was able to drop the corms at required nominal spacing
with minor variations. The highest deviation from the mean corm
spacing was observed as 3.53 cm with maximum coefficient of
variation as 13.88%. The highest missing and quality of feed indexes
were observed as 6.33% and 97.45% respectively with no multiples.
The performance of the planter was observed better at lower forward
speed and wider corm spacing. The field capacity of the planter was
found as 0.103 ha/h with an observed field efficiency of 76.57%.
Abstract: This research was made during the 2015 growing
periods in the trial filed of "Research Station for Department of Field
Crops, Agricultural Faculty, Selcuk University" according to
“Randomized Blocks Design” with 3 replications. Research material
was the following pea lines; PS16, PS18, PS21, PS23, PS24, PS25,
PS36, PS47, PS49, PS51, PS54, PS58, PS67, PS69, PS71, PS73,
PS83, PS84, PS87 and PSKY and three cultivars and other 2
commercial varieties named as Bolero, Rondo and Ultrello. Some
agronomical characteristics such as plant height (cm) number of pod
per plant number of seed per pod number of seed per plant 100 seed
weight (g) and seed yield (kg ha-1) were determined. The highest seed
yield was obtained 2727.0 kg ha-1 in the PS71 line and the lowest
value was obtained 1238.0 kg ha-1 in the commercial variety of
Bolero. Results of the research implicated that the new developed
lines were superior compared with the control (commercial) varieties
by means of most of the characteristics. Nevertheless, similar
researches should be continued in different locations and years.
Abstract: The Com-Poisson (CMP) model is one of the most
popular discrete generalized linear models (GLMS) that handles
both equi-, over- and under-dispersed data. In longitudinal context,
an integer-valued autoregressive (INAR(1)) process that incorporates
covariate specification has been developed to model longitudinal
CMP counts. However, the joint likelihood CMP function is
difficult to specify and thus restricts the likelihood-based estimating
methodology. The joint generalized quasi-likelihood approach
(GQL-I) was instead considered but is rather computationally
intensive and may not even estimate the regression effects due
to a complex and frequently ill-conditioned covariance structure.
This paper proposes a new GQL approach for estimating the
regression parameters (GQL-III) that is based on a single score vector
representation. The performance of GQL-III is compared with GQL-I
and separate marginal GQLs (GQL-II) through some simulation
experiments and is proved to yield equally efficient estimates as
GQL-I and is far more computationally stable.
Abstract: A field experiment was conducted in the Agricultural
Research Station, at El-Ghoraieb, Assiut to study dry seed yield
performance of two locally adapted cultivars (‘Azmerly’ and ‘Cream
7’) and two line introductions (IT81D-1032 and IT82D-812) of
common cowpea (Vigna unguiculata (L.) Walp) grown at three
different within-row spaces (20, 30 and 40 cm) and two planting
dates in the summer (April 15th and 30th) and in the fall season (Aug.
12th and 27th) of two successive seasons. The data showed that total
dry-seed yield produced by plants grown at 20 cm was greater than at
30 cm in all cvs/lines in both years. Increases in 1000-seed weight
were detected in cv ‘Azmerly’ and line IT82D-812 when they were
grown at 30 cm as compared with 20 cm in the summer season.
However, in the fall season such increases were found in all cvs/lines.
Planting at 40 cm produced seeds of greater weight than planting at
30 cm for all cvs/lines in the fall season and also in cv. Cream 7 and
line IT82D-812 in the summer season, while all cvs/lines in the fall
Planting on April 15th in the summer and also planting on Aug. 12th
in the fall had plants which showed increases in 1000-seed weight
and total dry-seed yield. The greatest 1000-seed weight was found in
the line IT81D-1032 in the summer season and in the line IT82D-812
in the fall season. The sum up results revealed that ‘Azmerly’
produced greater dry-seed yield than ‘Cream 7’ and both of them
were superior to the line IT82D-812 and IT81D-1032 in the summer
season. In the fall, however, the line IT82D-812 produced greater
dry-seed yield than the other cultivars/lines.