Abstract: The present paper discusses the basic concepts and the underlying principles of Multi-Agent Systems (MAS) along with an interdisciplinary exploitation of these principles. It has been found that they have been utilized for lots of research and studies on various systems spanning across diverse engineering and scientific realms showing the need of development of a proper generalized framework. Such framework has been developed for the Multi-Agent Systems and it has been generalized keeping in mind the diverse areas where they find application. All the related aspects have been categorized and a general definition has been given where ever possible.
Abstract: Water leakage is a serious problem in the maintenance of a waterworks facility. Monitoring the water flow rate is one way to locate leakage. However, conventional flowmeters such as the wet-type flowmeter and the clamp-on type ultrasonic flowmeter require additional construction for their installation and are therefore quite expensive. This paper proposes a novel estimation system for the flow rate in a water pipeline, which employs a vibration sensor. This assembly can be attached to any water pipeline without the need for additional high-cost construction. The vibration sensor is designed based on a condenser microphone. This sensor detects vibration caused by water flowing through a pipeline. It is possible to estimate the water flow rate by measuring the amplitude of the output signal from the vibration sensor. We confirmed the validity of the proposed sensing system experimentally.
Abstract: Excilamps are new UV sources with great potential
for application in wastewater treatment. In the present work, a XeBr
excilamp emitting radiation at 283 nm has been used for the
photodegradation of 4-chlorophenol within a range of concentrations
from 50 to 500 mg L-1. Total removal of 4-chlorophenol was
achieved for all concentrations assayed. The two main photoproduct
intermediates formed along the photodegradation process,
benzoquinone and hydroquinone, although not being completely
removed, remain at very low residual concentrations. Such
concentrations are insignificant compared to the 4-chlorophenol
initial ones and non-toxic. In order to simulate the process and scaleup,
a kinetic model has been developed and validated from the
experimental data.
Abstract: The policies governing the business of any
organization are well reflected in her business rules. The business
rules are implemented by data validation techniques, coded during
the software development process. Any change in business
policies results in change in the code written for data validation
used to enforce the business policies. Implementing the change in
business rules without changing the code is the objective of this
paper. The proposed approach enables users to create rule sets at
run time once the software has been developed. The newly defined
rule sets by end users are associated with the data variables for
which the validation is required. The proposed approach facilitates
the users to define business rules using all the comparison
operators and Boolean operators. Multithreading is used to
validate the data entered by end user against the business rules
applied. The evaluation of the data is performed by a newly
created thread using an enhanced form of the RPN (Reverse Polish
Notation) algorithm.
Abstract: Modern times call organizations to have an active role
in the social arena, through Corporate Social Responsibility (CSR).
The objective of this research was to test the hypothesis that there is a
positive relation between social performance and economic
performance, and if there is a positive correlation between social
performance and financial-economic performance. To test these
theories a measure of social performance, based on the Green Book
of Commission of the European Community, was used in a group of
nineteen Portuguese top companies, listed on the PSI 20 index,
through a period of five years, since 2005 to 2009. A clusters
analysis was applied to group companies by their social performance
and to compare and correlate their economic performance. Results
indicate that companies that had a better social performance are not
the ones who had a better economic performance, and suggest that
the middle path might provide a good relation CSR-Economic
performance, as a basis to a sustainable development.
Abstract: Modeling of a manufacturing system enables one to
identify the effects of key design parameters on the system performance and as a result to make correct decision. This paper
proposes a manufacturing system modeling approach using a spreadsheet model based on queuing network theory, in which a
static capacity planning model and stochastic queuing model are integrated. The model was used to improve the existing system utilization in relation to product design. The model incorporates few
parameters such as utilization, cycle time, throughput, and batch size.
The study also showed that the validity of developed model is good enough to apply and the maximum value of relative error is 10%, far
below the limit value 32%. Therefore, the model developed in this
study is a valuable alternative model in evaluating a manufacturing system
Abstract: The paper discusses European Lifelong Learning policy in the European enlargement to the Balkan. The European Lifelong Learning policy with Human Capital approach is researched in the country case of Macedonia. The paper argues that Human Capital approach focusing on instrumental and economic importance of learning for employability and economic growth needs to be complemented with Capability Approach for intrinsic and noneconomic needs of learning among the ethnic minorities. The paper identifies two dimensions of importance – minority languages and civic education – that the Capability Approach may develop to guarantee equal opportunities to all to benefit from European educational and lifelong learning development and to build an inclusive and socially just democracy in Macedonia.
Abstract: Key performance indicators (KPIs) are used for post
result evaluation in the construction industry, and they normally do
not have provisions for changes. This paper proposes a set of
dynamic key performance indicators (d-KPIs) which predicts the
future performance of the activity being measured and presents the
opportunity to change practice accordingly. Critical to the
predictability of a construction project is the ability to achieve
automated data collection. This paper proposes an effective way to
collect the process and engineering management data from an
integrated construction management system. The d-KPI matrix,
consisting of various indicators under seven categories, developed
from this study can be applied to close monitoring of the
development projects of aged-care facilities. The d-KPI matrix also
enables performance measurement and comparison at both project
and organization levels.
Abstract: Mobile marketing through mobile messaging service
has highly impressive growth as it enables e-business firms to
communicate with their customers effectively. Educational
institutions hence start using this service to enhance communication
with their students. Previous studies, however, have limited
understanding of applying mobile messaging service in education.
This study proposes a theoretical model to understand the drivers of
students- intentions to use the university-s mobile messaging service.
The model indicates that social influence, perceived control and
attitudes affect students- intention to use the university-s mobile
messaging service. It also provides five antecedents of students-
attitudes–perceived utility (information utility, entertainment utility,
and social utility), innovativeness, information seeking, transaction
specificity (content specificity, sender specificity, and time
specificity) and privacy concern. The proposed model enables
universities to understand what students concern about the use of a
mobile messaging service in universities and handle the service more
effectively. The paper discusses the model development and
concludes with limitations and implications of the proposed model.
Abstract: The paper contains a review of the literature in terms of the critical analysis of methodologies of university ranking systems. Furthermore, the initiatives supported by the European Commission (U-Map, U-Multirank) and CHE Ranking are described. Special attention is paid to the tendencies in the development of ranking systems. According to the author, the ranking organizations should abandon the classic form of ranking, namely a hierarchical ordering of universities from “the best" to “the worse". In the empirical part of this paper, using one of the method of cluster analysis called k-means clustering, the author presents university classifications of the top universities from the Shanghai Jiao Tong University-s (SJTU) Academic Ranking of World Universities (ARWU).
Abstract: Risk management is an essential fraction of project management, which plays a significant role in project success. Many failures associated with Web projects are the consequences of poor awareness of the risks involved and lack of process models that can serve as a guideline for the development of Web based applications. To circumvent this problem, contemporary process models have been devised for the development of conventional software. This paper introduces the WPRiMA (Web Project Risk Management Assessment) as the tool, which is used to implement RIAP, the risk identification architecture pattern model, which focuses upon the data from the proprietor-s and vendor-s perspectives. The paper also illustrates how WPRiMA tool works and how it can be used to calculate the risk level for a given Web project, to generate recommendations in order to facilitate risk avoidance in a project, and to improve the prospects of early risk management.
Abstract: In this paper, a fiber based Fabry-Perot interferometer
is proposed and demonstrated for a non-contact displacement
measurement. A piece of micro-prism which attached to the
mechanical vibrator is served as the target reflector. Interference
signal is generated from the superposition between the sensing beam
and the reference beam within the sensing arm of the fiber sensor.
This signal is then converted to the displacement value by using a
developed program written in visual Cµ programming with a
resolution of λ/8. A classical function generator is operated for
controlling the vibrator. By fixing an excitation frequency of 100 Hz
and varying the excitation amplitude range of 0.1 – 3 Volts, the
output displacements measured by the fiber sensor are obtained from
1.55 μm to 30.225 μm. A reference displacement sensor with a
sensitivity of ~0.4 μm is also employed for comparing the
displacement errors between both sensors. We found that over the
entire displacement range, a maximum and average measurement
error are obtained of 0.977% and 0.44% respectively.
Abstract: Cooperative organizations in Malaysia are going
through a phase of rapid growth. They are seen by the government as
another crucial vehicle to drive and boost up the country-s
economical development and growth. Hence, the issue of cooperative
governance is of great importance. Unlike literatures on corporate
governance for public listed companies-, literatures on governance
for social enterprises, in particular the cooperative organizations are
still at the early stage in Malaysia and very scant in number. This
paper will look into current practices as well as issues and challenges
related to cooperative governance. The need for a better solution
towards forming best practices of cooperative governance framework
appears imperative in deterring cases of mismanagement and fraud.
Abstract: Unsatisfactory effectiveness of software systems
development and enhancement projects is one of the main reasons
why in software engineering there are attempts being made to use
experiences coming from other engineering disciplines. In spite of
specificity of software product and process a belief had come out that
the execution of software could be more effective if these objects
were subject to measurement – as it is true in other engineering
disciplines for which measurement is an immanent feature. Thus
objective and reliable approaches to the measurement of software
processes and products have been sought in software engineering for
several dozens of years already. This may be proved, among others,
by the current version of CMMI for Development model. This paper
is aimed at analyzing the approach to the software processes and
products measurement proposed in the latest version of this very
model, indicating growing acceptance for this issue in software
engineering.
Abstract: A numbers of important developments have led to an
increasing attractiveness for very high speed electrical machines
(either motor or generator). Specifically the increasing switching
speed of power electronics, high energy magnets, high strength
retaining materials, better high speed bearings and improvements in
design analysis are the primary drivers in a move to higher speed. The
design challenges come in the mechanical design both in terms of
strength and resonant modes and in the electromagnetic design
particularly in respect of iron losses and ac losses in the various
conducting parts including the rotor. This paper describes detailed
design work which has been done on a 50,000 rpm, 50kW permanent
magnet( PM) synchronous machine. It describes work on
electromagnetic and rotor eddy current losses using a variety of
methods including both 2D finite element analysis
Abstract: Two novel hydrodesulfurization (HDS) catalysts:
FeN4/C and FeN2/C, were prepared using an impregnation-pyrolysis
method. The two materials were investigated as catalysts for
hydrodesulfurization (HDS) and hydrodearomitization (HDA) of
model compounds. The turnover frequency of the two FeN catalysts
is comparable to (FeN4/C) or even higher (FeN2/C) than that of
MoNi/Al2O3. The FeN4/C catalyst also exhibited catalytic activity
toward HDA.
Abstract: The importance for manipulating an incorporated
scaffold and directing cell behaviors is well appreciated for tissue
engineering. Here, we developed newly nano-topographic oxidized
silicon nanosponges capable of being various chemical modifications
to provide much insight into the fundamental biology of how cells
interact with their surrounding environment in vitro. A wet etching
technique is exerted to allow us fabricated the silicon nanosponges in a
high-throughput manner. Furthermore, various organo-silane
chemicals enabled self-assembled on the surfaces by vapor deposition.
We have found that Chinese hamster ovary (CHO) cells displayed
certain distinguishable morphogenesis, adherent responses, and
biochemical properties while cultured on these chemical modified
nano-topographic structures in compared with the planar oxidized
silicon counterparts, indicating that cell behaviors can be influenced
by certain physical characteristic derived from nano-topography in
addition to the hydrophobicity of contact surfaces crucial for cell
adhesion and spreading. Of particular, there were predominant
nano-actin punches and slender protrusions formed while cells were
cultured on the nano-topographic structures. This study shed potential
applications of these nano-topographic biomaterials for controlling
cell development in tissue engineering or basic cell biology research.
Abstract: Determination of wellbore problems during a
production/injection process might be evaluated thorough
temperature log analysis. Other applications of this kind of log
analysis may also include evaluation of fluid distribution analysis
along the wellbore and identification of anomalies encountered
during production/injection process. While the accuracy of such
prediction is paramount, the common method of determination of a
wellbore temperature log includes use of steady-state energy balance
equations, which hardly describe the real conditions as observed in
typical oil and gas flowing wells during production operation; and
thus increase level of uncertainties. In this study, a practical method
has been proposed through development of a simplified semianalytical
model to apply for predicting temperature profile along the
wellbore. The developed model includes an overall heat transfer
coefficient accounting all modes of heat transferring mechanism,
which has been focused on the prediction of a temperature profile as
a function of depth for the injection/production wells. The model has
been validated with the results obtained from numerical simulation.
Abstract: Purpose of this paper is two-folded. At first it explains
the major problems that are causing stagnation in brownfield
redevelopment. In addition, these problems given the context of the
present multi-actor built environment are becoming more complex to
observe. Therefore, this paper suggests also a prospective decisionmaking
approach that is the most appropriate to observe and react on
the given stagnation problems. Such an approach should be regarded
as prescriptive-interactive decision-making approach, a barely
established branch. This approach should offer models that have
prescriptive as well as an interactive component enabling them to
successfully cope with the multi-actor environment. Overall, this
paper provides up-to-date insight on the brownfield stagnation by
gradually introducing the nowadays major problems and offers a
prospective decision-making approach how these problems could be
tackled.
Abstract: Food and fibre production in arid and semi-arid regions has emerged as one of the major challenges for various socio-economic and political reasons such as the food security and self-sufficiency. Productive use of the renewable water resources has risen on top ofthe decision-making agenda. For this reason, efficient operation and maintenance of modern irrigation and drainage schemes become part and parcel and indispensible reality in agricultural policy making arena. The aim of this paper is to investigate the complexity of operating and maintaining such schemes, mainly focussing on challenges which enhance and opportunities that impedsustainable food and fibre production. The methodology involved using secondary data complemented byroutine observations and stakeholders views on issues that influence the O&M in the Dez command area. The SPSS program was used as an analytical framework for data analysis and interpretation.Results indicate poor application efficiency in most croplands, much of which is attributed to deficient operation of conveyance and distribution canals. These in turn, are reportedly linked to inadequate maintenance of the pumping stations and hydraulic structures like turnouts,flumes and other control systems particularly in the secondary and tertiary canals. Results show that the aforementioned deficiencies have been the major impediment to establishing regular flow toward the farm gates which subsequently undermine application efficiency and tillage operationsat farm level. Results further show that accumulative impact of such deficiencies has been the major causes of poorcrop yield and quality that deem production system in these croplands uneconomic. Results further show that the present state might undermine the sustainability of agricultural system in the command area. The overall conclusion being that present water management is unlikely to be responsive to challenges that the sector faces. And in the absence of coherent measures to shift the status quo situation in favour of more productive resource use, it would be hard to fulfil the objectives of the National Economic and Socio-cultural Development Plans.