Abstract: One promising way to achieve low temperature
combustion regime is the use of a large amount of cooled EGR. In
this paper, the effect of injection timing on low temperature
combustion process and emissions were investigated via three
dimensional computational fluid dynamics (CFD) procedures in a DI
diesel engine using high EGR rates. The results show when
increasing EGR from low levels to levels corresponding to reduced
temperature combustion, soot emission after first increasing, is
decreased beyond 40% EGR and get the lowest value at 58% EGR
rate. Soot and NOx emissions are simultaneously decreased at
advanced injection timing before 20.5 ºCA BTDC in conjunction
with 58% cooled EGR rate in compared to baseline case.
Abstract: Thermoacoustic instabilities in combustors have
remained a topic of investigation for over a few decades due to the
challenges it posses to the operation of low emission gas turbines.
For combustors burning liquid fuel, understanding the cause-andeffect
relationship between spray combustion dynamics and
thermoacoustic oscillations is imperative for the successful
development of any control methodology for its mitigation. The
paper presents some very unique operating characteristics of a
kerosene-fueled diffusion type combustor undergoing limit-cycle
oscillations. Combustor stability limits were mapped using three
different-sized injectors. The results show that combustor instability
depends on the characteristics of the fuel spray. A simple analytic
analysis is also reported in support of a plausible explanation for the
unique combustor behavior. The study indicates that high amplitude
acoustic pressure in the combustor may cause secondary breakdown
of fuel droplets resulting in premixed pre-vaporized type burning of
the diffusion type combustor.
Abstract: Many studies have emphasized the importance of
resistive exercise to maintain a healthy human body, particular in
prevention of weakening of physical strength. Recently, some studies
advocated that an application of vibration as a supplementary means in
a regular training was effective in encouraging physical strength. Aim
of the current study was, therefore, to identify if an application of
vibration in a resistive exercise was effective in encouraging physical
strength as that in a regular training. A 3-dimensional virtual lower
extremity model for a healthy male and virtual leg-press model were
generated and synchronized. Dynamic leg-press exercises on a slide
machine with/without extra load and on a footboard with vibration as
well as on a slide machine with extra load were analyzed. The results
of the current indicated that the application of the vibration on the
dynamic leg-press exercise might be not greatly effective in
encouraging physical strength, compared with the dynamic leg press
exercise with extra load. It was, however, thought that the application
of the vibration might be helpful to elderly individuals because the
reduced maximum muscle strength appeared by the effect of the
vibration may avoid a muscular spasm, which can be driven from a
high muscle strength sometimes produced during the leg-press
exercise with extra load.
Abstract: To investigate the applicability of the EDR-2 film for
clinical radiation dosimetry, percentage depth-doses, profiles and
distributions in open and dynamically wedged fields were measured
using film and compared with data from a Treatment Planning
system.The validity of the EDR2 film to measure dose in a plane
parallel to the beam was tested by irradiating 10 cm×10 cm and 4
cm×4 cm fields from a Siemens, primus linac with a 6MV beam and
a source-to-surface distance of 100 cm. The film was placed
Horizontally between solid water phantom blocks and marked
with pin holes at a depth of 10 cm from the incident beam surface.
The film measurement results, in absolute dose, were compared with
ion chamber measurements using a Welhoffer scanning water tank
system and Treatment Planning system. Our results indicate a
maximum underestimate of calculated dose of 8 % with Treatment
Planning system.
Abstract: Laboratory experiments have been performed to investigate photocatalytic detoxification by using TiO2 photocatalyst for treating dairy effluent. Various operational parameters such as catalyst concentration, initial concentration, angle of tilt of solar flat plate reactor and flow rate were investigated. Results indicated that the photocatalytic detoxification process can efficiently treat dairy effluent. Experimental runs with dairy wastewater can be used to identify the optimum operational parameters to perform wastewater degradation on large scale for recycling purpose. Also effect of two different types of reactors on degradation process was analyzed.
Abstract: Numerical integration of initial boundary problem for advection equation in 3 ℜ is considered. The method used is
conditionally stable semi-Lagrangian advection scheme with high order interpolation on unstructured mesh. In order to increase time step integration the BFECC method with limiter TVD correction is used. The method is adopted on parallel graphic processor unit environment using NVIDIA CUDA and applied in Navier-Stokes solver. It is shown that the calculation on NVIDIA GeForce 8800
GPU is 184 times faster than on one processor AMDX2 4800+ CPU. The method is extended to the incompressible fluid dynamics solver. Flow over a Cylinder for 3D case is compared to the experimental data.
Abstract: Segmentation of a color image composed of different
kinds of regions can be a hard problem, namely to compute for an
exact texture fields. The decision of the optimum number of
segmentation areas in an image when it contains similar and/or un
stationary texture fields. A novel neighborhood-based segmentation
approach is proposed. A genetic algorithm is used in the proposed
segment-pass optimization process. In this pass, an energy function,
which is defined based on Markov Random Fields, is minimized. In
this paper we use an adaptive threshold estimation method for image
thresholding in the wavelet domain based on the generalized
Gaussian distribution (GGD) modeling of sub band coefficients. This
method called Normal Shrink is computationally more efficient and
adaptive because the parameters required for estimating the threshold
depend on sub band data energy that used in the pre-stage of
segmentation. A quad tree is employed to implement the multi
resolution framework, which enables the use of different strategies at
different resolution levels, and hence, the computation can be
accelerated. The experimental results using the proposed
segmentation approach are very encouraging.
Abstract: The efficient use of available licensed spectrum is
becoming more and more critical with increasing demand and usage
of the radio spectrum. This paper shows how the use of spectrum as
well as dynamic spectrum management can be effectively managed
and spectrum allocation schemes in the wireless communication
systems be implemented and used, in future. This paper would be an
attempt towards better utilization of the spectrum. This research will
focus on the decision-making process mainly, with an
assumption that the radio environment has already been sensed and
the QoS requirements for the application have been specified either
by the sensed radio environment or by the secondary user itself. We
identify and study the characteristic parameters of Cognitive Radio
and use Genetic Algorithm for spectrum allocation. Performance
evaluation is done using MATLAB toolboxes.
Abstract: The present work deals with the structural analysis of
turbine blades and modeling of turbine blades. A common failure
mode for turbine machines is high cycle of fatigue of compressor and
turbine blades due to high dynamic stresses caused by blade vibration
and resonance within the operation range of the machinery. In this
work, proper damping system will be analyzed to reduce the
vibrating blade. The main focus of the work is the modeling of under
platform damper to evaluate the dynamic analysis of turbine-blade
vibrations. The system is analyzed using Bond graph technique. Bond
graph is one of the most convenient ways to represent a system from
the physical aspect in foreground. It has advantage of putting together
multi-energy domains of a system in a single representation in a
unified manner. The bond graph model of dry friction damper is
simulated on SYMBOLS-shakti® software. In this work, the blades
are modeled as Timoshenko beam. Blade Vibrations under different
working conditions are being analyzed numerically.
Abstract: Buildings with floating column are highly undesirable built in seismically active areas. Many urban multi-storey buildings today have floating column buildings which are adopted to accommodate parking at ground floor or reception lobbies in the first storey. The earthquake forces developed at different floor levels in a building need to be brought down along the height to the ground by the shortest path; any deviation or discontinuity in this load transfer path results in poor performance of the building. Floating column buildings are severely damaged during earthquake. Damage on this structure can be reduce by taking the effect of infill wall. This paper presents the effect of stiffness of infill wall to the damage occurred in floating column building when ground shakes. Modelling and analysis are carried out by non linear analysis programme IDARC-2D. Damage occurred in beams, columns, storey are studied by formulating modified Park & Ang model to evaluate damage indices. Overall structural damage indices in buildings due to shaking of ground are also obtained. Dynamic response parameters i.e. lateral floor displacement, storey drift, time period, base shear of buildings are obtained and results are compared with the ordinary moment resisting frame buildings. Formation of cracks, yield, plastic hinge, are also observed during analysis.
Abstract: The aim of this study was to develop a dynamic cardiac phantom for quality control in myocardial scintigraphy. The dynamic heart phantom constructed only contained the left ventricle, made of elastic material (latex), comprising two cavities: one internal and one external. The data showed a non-significant variation in the values of left ventricular ejection fraction (LVEF) obtained by varying the heart rate. It was also possible to evaluate the ejection fraction (LVEF) through different arrays of image acquisition and to perform an intercomparison of LVEF by two different scintillation cameras. The results of the quality control tests were satisfactory, showing that they can be used as parameters in future assessments. The new dynamic heart phantom was demonstrated to be effective for use in LVEF measurements. Therefore, the new heart simulator is useful for the quality control of scintigraphic cameras.
Abstract: The objective of this paper is to develop a neural
network-based residual generator to detect the fault in the actuators
for a specific communication satellite in its attitude control system
(ACS). First, a dynamic multilayer perceptron network with dynamic
neurons is used, those neurons correspond a second order linear
Infinite Impulse Response (IIR) filter and a nonlinear activation
function with adjustable parameters. Second, the parameters from the
network are adjusted to minimize a performance index specified by
the output estimated error, with the given input-output data collected
from the specific ACS. Then, the proposed dynamic neural network
is trained and applied for detecting the faults injected to the wheel,
which is the main actuator in the normal mode for the communication
satellite. Then the performance and capabilities of the proposed
network were tested and compared with a conventional model-based
observer residual, showing the differences between these two
methods, and indicating the benefit of the proposed algorithm to
know the real status of the momentum wheel. Finally, the application
of the methods in a satellite ground station is discussed.
Abstract: A new mechanism responsible for structural life
consumption due to resonant fatigue in turbine blades, or vanes, is
presented and explained. A rotating blade or vane in a gas turbine can
change its contour due to erosion and/or material build up, in any of
these instances, the surface pressure distribution occurring on the
suction and pressure sides of blades-vanes can suffer substantial
modification of their pressure and temperatures envelopes and flow
characteristics. Meanwhile, the relative rotation between the blade
and duct vane while the pressurized gas flows and the consequent
wake crossings, will induce a fluctuating thrust force or lift that will
excite the blade.
An actual totally used up set of vane-blade components in a HP
turbine power stage in a gas turbine is analyzed. The blade suffered
some material erosion mostly at the trailing edge provoking a
peculiar surface pressure envelope which evolved as the relative
position between the vane and the blade passed in front of each other.
Interestingly preliminary modal analysis for this eroded blade
indicates several natural frequencies within the aeromechanic power
spectrum, moreover, the highest frequency component is 94% of one
natural frequency indicating near resonant condition.
Independently of other simultaneously occurring fatigue cycles
(such as thermal, centrifugal stresses).
Abstract: CO2 is the primary anthropogenic greenhouse gas,
accounting for 77% of the human contribution to the greenhouse
effect in 2004. In the recent years, global concentration of CO2 in the
atmosphere is increasing rapidly. CO2 emissions have an impact on
global climate change. Anthropogenic CO2 is emitted primarily from
fossil fuel combustion. Carbon capture and storage (CCS) is one
option for reducing CO2 emissions. There are three major approaches
for CCS: post-combustion capture, pre-combustion capture and
oxyfuel process. Post-combustion capture offers some advantages as
existing combustion technologies can still be used without radical
changes on them.
There are several post combustion gas separation and capture
technologies being investigated, namely; (a) absorption, (b)
cryogenic separation, (c) membrane separation (d) micro algal biofixation
and (e) adsorption. Apart from establishing new techniques,
the exploration of capture materials with high separation performance
and low capital cost are paramount importance. However, the
application of adsorption from either technology, require easily
regenerable and durable adsorbents with a high CO2 adsorption
capacity. It has recently been reported that the cost of the CO2
capture can be reduced by using this technology. In this paper, the
research progress (from experimental results) in adsorbents for CO2
adsorption, storage, and separations were reviewed and future
research directions were suggested as well.
Abstract: This paper presents the combination of different precipitation data sets and the distributed hydrological model, in order to examine the flood runoff reproductivity of scattered observation catchments. The precipitation data sets were obtained from observation using rain-gages, satellite based estimate (TRMM), and numerical weather prediction model (NWP), then were coupled with the super tank model. The case study was conducted in three basins (small, medium, and large size) located in Central Vietnam. Calculated hydrographs based on ground observation rainfall showed best fit to measured stream flow, while those obtained from TRMM and NWP showed high uncertainty of peak discharges. However, calculated hydrographs using the adjusted rainfield depicted a promising alternative for the application of TRMM and NWP in flood modeling for scattered observation catchments, especially for the extension of forecast lead time.
Abstract: Vehicular communications play a substantial role in providing safety in transportation by means of safety message exchange. Researchers have proposed several solutions for securing safety messages. Protocols based on a fixed key infrastructure are more efficient in implementation and maintain stronger security in comparison with dynamic structures. These protocols utilize zone partitioning to establish distinct key infrastructure under Certificate Authority (CA) supervision in different regions. Secure anonymous broadcasting (SAB) is one of these protocols that preserves most of security aspects but it has some deficiencies in practice. A very important issue is region change of a vehicle for its mobility. Changing regions leads to change of CA and necessity of having new key set to resume communication. In this paper, we propose solutions for informing vehicles about region change to obtain new key set before entering next region. This hinders attackers- intrusion, packet loss and lessons time delay. We also make key request messages secure by confirming old CA-s public key to the message, hence stronger security for safety message broadcasting is attained.
Abstract: This paper presents the design of a low power second-order continuous-time sigma-delta modulator for low power
applications. The loop filter of this modulator has been implemented based on the nonlinear transconductance-capacitor (Gm-C) by employing current-mode technique. The nonlinear transconductance uses floating gate MOS (FG-MOS) transistors that operate in weak inversion region. The proposed modulator features low power consumption (
Abstract: Due to the excess of a vehicle operation through its life, some elements may face failure and deteriorate with time. This leads us to carry out maintenance, repair, tune up or full overhaul. After a certain period, the vehicle elements deteriorations increase with time which causes a very high increase of doing the maintenance operations and their costs. However, the logic decision at this point is to replace the current vehicle by a new one with minimum failure and maximum income. The importance of studying vehicle replacement problems come from the increase of stopping days due to many deteriorations in the vehicle parts. These deteriorations increase year after year causing an increase of operating costs and decrease the vehicle income. Vehicle replacement aims to determine the optimum time to keep, maintain, overhaul, renew and replace vehicles. This leads to an improvement in vehicle income, total operating costs, maintenance cost, fuel and oil costs, ton-kilometers, vehicle and engine performance, vehicle noise, vibration, and pollution. The aim of this paper is to find the optimum replacement policies of Kuwait Passenger Transport Company (KPTCP) fleet of busses. The objective of these policies is to maximize the busses pure profits. The dynamic programming (D.P.) technique is used to generate the busses optimal replacement policies
Abstract: Several recent studies have shown that the
transparency of financial reporting have a significant influence on investor-s decisions. Thus, regulation authorities and professional
organizations (IFAC) have emphasized the role of XBRL (eXtensible Business Reporting Language) and interactive data as a means of
promoting transparency and monitoring corporate reporting. In this
context, this paper has as objective the analysis of interactive reporting through XBRL and its use as a support in the process of
taking decisions in corporate governance, namely the potential of interactive reports in XBRL to increase the transparency and
monitoring process of corporate governance.
Abstract: The database reverse engineering problems and
solving processes are getting mature, even though, the academic
community is facing the complex problem of knowledge transfer,
both in university and industrial contexts. This paper presents a new
CASE tool developed at the University of Jordan which addresses an
efficient support of this transfer, namely UJ-CASE-TOOL. It is a
small and self-contained application exhibiting representative
problems and appropriate solutions that can be understood in a
limited time. It presents an algorithm that describes the developed
academic CASE tool which has been used for several years both as
an illustration of the principles of database reverse engineering and
as an exercise aimed at academic and industrial students.