Abstract: Experimental data from an atmospheric air/water terrain slugging case has been made available by the Shell Amsterdam research center, and has been subject to numerical simulation and comparison with a one-dimensional two-phase slug tracking simulator under development at the Norwegian University of Science and Technology. The code is based on tracking of liquid slugs in pipelines by use of a Lagrangian grid formulation implemented in Cµ by use of object oriented techniques. An existing hybrid spatial discretization scheme is tested, in which the stratified regions are modelled by the two-fluid model. The slug regions are treated incompressible, thus requiring a single momentum balance over the whole slug. Upon comparison with the experimental data, the period of the simulated severe slugging cycle is observed to be sensitive to slug generation in the horizontal parts of the system. Two different slug initiation methods have been tested with the slug tracking code, and grid dependency has been investigated.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: The characteristics of fluid flow and phase separation
in an oil-water separator were numerically analysed as part of the
work presented herein. Simulations were performed for different
velocities and droplet diameters, and the way this parameters can
influence the separator geometry was studied.
The simulations were carried out using the software package
Fluent 6.2, which is designed for numerical simulation of fluid flow
and mass transfer. The model consisted of a cylindrical horizontal
separator. A tetrahedral mesh was employed in the computational
domain. The condition of two-phase flow was simulated with the
two-fluid model, taking into consideration turbulence effects using
the k-ε model.
The results showed that there is a strong dependency of phase
separation on mixture velocity and droplet diameter. An increase in
mixture velocity will bring about a slow down in phase separation
and as a consequence will require a weir of greater height. An
increase in droplet diameter will produce a better phase separation.
The simulations are in agreement with results reported in literature
and show that CFD can be a useful tool in studying a horizontal oilwater
separator.
Abstract: This paper describes the development of an
autonomous robot for painting the interior walls of buildings. The
robot consists of a painting arm with an end effector roller that scans
the walls vertically and a mobile platform to give horizontal feed to
paint the whole area of the wall. The painting arm has a planar twolink
mechanism with two joints. Joints are driven from a stepping
motor through a ball screw-nut mechanism. Four ultrasonic sensors
are attached to the mobile platform and used to maintain a certain
distance from the facing wall and to avoid collision with side walls.
When settled on adjusted distance from the wall, the controller starts
the painting process autonomously. Simplicity, relatively low weight
and short painting time were considered in our design. Different
modules constituting the robot have been separately tested then
integrated. Experiments have shown successfulness of the robot in its
intended tasks.
Abstract: The evaluation and measurement of human body
dimensions are achieved by physical anthropometry. This research
was conducted in view of the importance of anthropometric indices
of the face in forensic medicine, surgery, and medical imaging. The
main goal of this research is to optimization of facial feature point by
establishing a mathematical relationship among facial features and
used optimize feature points for age classification. Since selected
facial feature points are located to the area of mouth, nose, eyes and
eyebrow on facial images, all desire facial feature points are extracted
accurately. According this proposes method; sixteen Euclidean
distances are calculated from the eighteen selected facial feature
points vertically as well as horizontally. The mathematical
relationships among horizontal and vertical distances are established.
Moreover, it is also discovered that distances of the facial feature
follows a constant ratio due to age progression. The distances
between the specified features points increase with respect the age
progression of a human from his or her childhood but the ratio of the
distances does not change (d = 1 .618 ) . Finally, according to the
proposed mathematical relationship four independent feature
distances related to eight feature points are selected from sixteen
distances and eighteen feature point-s respectively. These four feature
distances are used for classification of age using Support Vector
Machine (SVM)-Sequential Minimal Optimization (SMO) algorithm
and shown around 96 % accuracy. Experiment result shows the
proposed system is effective and accurate for age classification.
Abstract: In this paper, a theoretical formula is presented to
predict the instantaneous folding force of the first fold creation in a
square column under axial loading. Calculations are based on analysis
of “Basic Folding Mechanism" introduced by Wierzbicki and
Abramowicz. For this purpose, the sum of dissipated energy rate under
bending around horizontal and inclined hinge lines and dissipated
energy rate under extensional deformations are equated to the work rate
of the external force on the structure. Final formula obtained in this
research, reasonably predicts the instantaneous folding force of the first
fold creation versus folding distance and folding angle and also predicts
the instantaneous folding force instead of the average value. Finally,
according to the calculated theoretical relation, instantaneous folding
force of the first fold creation in a square column was sketched
versus folding distance and was compared to the experimental results
which showed a good correlation.
Abstract: The Norwegian Military Academy (Army) has
initiated a project with the main ambition to explore possible avenues
to enhancing operational effectiveness through an increased use of
simulation-based training and exercises. Within a cost/benefit
framework, we discuss opportunities and limitations of vertical and
horizontal integration of the existing tactical training system. Vertical
integration implies expanding the existing training system to span the
full range of training from tactical level (platoon, company) to
command and staff level (battalion, brigade). Horizontal integration
means including other domains than army tactics and staff
procedures in the training, such as military ethics, foreign languages,
leadership and decision making. We discuss each of the integration
options with respect to purpose and content of training, "best
practice" for organising and conducting simulation-based training,
and suggest how to evaluate training procedures and measure
learning outcomes. We conclude by giving guidelines towards further
explorative work and possible implementation.
Abstract: The whole work is based on possibility to use Lego Mindstorms robotics systems to reduce costs. Lego Mindstorms consists of a wide variety of hardware components necessary to simulate, programme and test of robotics systems in practice. To programme algorithm, which simulates space using the ultrasonic sensor, was used development environment supplied with kit. Software Matlab was used to render values afterwards they were measured by ultrasonic sensor. The algorithm created for this paper uses theoretical knowledge from area of signal processing. Data being processed by algorithm are collected by ultrasonic sensor that scans 2D space in front of it. Ultrasonic sensor is placed on moving arm of robot which provides horizontal moving of sensor. Vertical movement of sensor is provided by wheel drive. The robot follows map in order to get correct positioning of measured data. Based on discovered facts it is possible to consider Lego Mindstorm for low-cost and capable kit for real-time modelling.
Abstract: With the presence of a uniform vertical magnetic field and suspended particles, thermocapillary instability in a horizontal liquid layer is investigated. The resulting eigenvalue is solved by the Galerkin technique for various basic temperature gradients. It is found that the presence of magnetic field always has a stability effect of increasing the critical Marangoni number.
Abstract: Response to the public health-related emergencies is analysed here for a rural university in South Africa. The structure of the designated emergency plan covers all the phases of the disaster management cycle. The plan contains elements of the vulnerability model and the technocratic model of emergency management. The response structures are vertically and horizontally integrated, while the planning contains elements of scenario-based and functional planning. The available number of medical professionals at the Rhodes University, along with the medical insurance rates, makes the staff and students potentially more medically vulnerable than the South African population. The main improvements of the emergency management are required in the tornado response and the information dissemination during health emergencies. The latter should involve the increased use of social media and e-mails, following the Taylor model of communication. Infrastructure must be improved in the telecommunication sector in the face of unpredictable electricity outages.
Abstract: Foundation of tower crane serves to ensure stability
against vertical and horizontal forces. If foundation stress is not
sufficient, tower crane may be subject to overturning, shearing or
foundation settlement. Therefore, engineering review of stable support
is a highly critical part of foundation design. However, there are not
many professionals who can conduct engineering review of tower
crane foundation and, if any, they have information only on a small
number of cranes in which they have hands-on experience. It is also
customary to rely on empirical knowledge and tower crane renter-s
recommendations rather than designing foundation on the basis of
engineering knowledge. Therefore, a foundation design automation
system considering not only lifting conditions but also overturning
risk, shearing and vertical force may facilitate production of foolproof
foundation design for experts and enable even non-experts to utilize
professional knowledge that only experts can access now. This study
proposes Automatic Design Algorithm for the Tower Crane
Foundations considering load and horizontal force.
Abstract: The main aim of this work is to establish the
capabilities of new green buildings to ascertain off-grid electricity
generation based on the integration of wind turbines in the
conceptual model of a rotating tower [2] in Dubai. An in depth
performance analysis of the WinWind 3.0MW [3] wind turbine is
performed. Data based on the Dubai Meteorological Services is
collected and analyzed in conjunction with the performance analysis
of this wind turbine. The mathematical model is compared with
Computational Fluid Dynamics (CFD) results based on a conceptual
rotating tower design model. The comparison results are further
validated and verified for accuracy by conducting experiments on a
scaled prototype of the tower design. The study concluded that
integrating wind turbines inside a rotating tower can generate enough
electricity to meet the required power consumption of the building,
which equates to a wind farm containing 9 horizontal axis wind
turbines located at an approximate area of 3,237,485 m2 [14].
Abstract: This work describes the aerodynamic characteristic for
aircraft wing model with and without bird feather like winglet. The
aerofoil used to construct the whole structure is NACA 653-218
Rectangular wing and this aerofoil has been used to compare the
result with previous research using winglet. The model of the
rectangular wing with bird feather like winglet has been fabricated
using polystyrene before design using CATIA P3 V5R13 software
and finally fabricated in wood. The experimental analysis for the
aerodynamic characteristic for rectangular wing without winglet,
wing with horizontal winglet and wing with 60 degree inclination
winglet for Reynolds number 1.66×105, 2.08×105 and 2.50×105 have
been carried out in open loop low speed wind tunnel at the
Aerodynamics laboratory in Universiti Putra Malaysia. The
experimental result shows 25-30 % reduction in drag coefficient and
10-20 % increase in lift coefficient by using bird feather like winglet
for angle of attack of 8 degree.
Abstract: The aerodynamics characteristics of a blended-wing body (BWB) aircraft were obtained in Universiti Teknologi MARA low speed wind tunnel. The scaled-down of BWB model consisted of a canard as its horizontal stabilizer. There were four canards with different aspect ratio used in the experiments. Canard setting angles were varied from -20q to 20q. All tests were conducted at velocity of 35 m/s, with Mach number 0.1. At low angles of attacks, the increment of lift slope for various canards aspect ratio is small and almost constant. Higher canard aspect ratio will cause higher drag. However, canard has a high effect to the moment at zero lift, CM,0.The visualization using mini tuff was performed to observe the airflow at the upper surface of canard. KeywordsAerodynamics,blended-wing body, canard, wind tunnel.
Abstract: The main objective of seismic rehabilitation in the
foundations is decreasing the range of horizontal and vertical
vibrations and omitting high frequencies contents under the seismic
loading. In this regard, the advantages of micropiles network is
utilized. Reduction in vibration range of foundation can be achieved
by using high dynamic rigidness module such as deep foundations. In
addition, natural frequency of pile and soil system increases in regard
to rising of system rigidness. Accordingly, the main strategy is
decreasing of horizontal and vertical seismic vibrations of the
structure. In this case, considering the impact of foundation, pile and
improved soil foundation is a primary concern. Therefore, in this
paper, effective factors are studied on the seismic rehabilitation of
foundations applying network micropiles in sandy soils with
nonlinear reaction.
Abstract: Character segmentation is an important preprocessing
step for text recognition. In degraded documents, existence of
touching characters decreases recognition rate drastically, for any
optical character recognition (OCR) system. In this paper we have
proposed a complete solution for segmenting touching characters in
all the three zones of printed Gurmukhi script. A study of touching
Gurmukhi characters is carried out and these characters have been
divided into various categories after a careful analysis. Structural
properties of the Gurmukhi characters are used for defining the
categories. New algorithms have been proposed to segment the
touching characters in middle zone, upper zone and lower zone.
These algorithms have shown a reasonable improvement in
segmenting the touching characters in degraded printed Gurmukhi
script. The algorithms proposed in this paper are applicable only to
machine printed text. We have also discussed a new and useful
technique to segment the horizontally overlapping lines.
Abstract: This paper presents probabilistic horizontal seismic
hazard assessment of Naghan, Iran. It displays the probabilistic
estimate of Peak Ground Horizontal Acceleration (PGHA) for the
return period of 475, 950 and 2475 years. The output of the
probabilistic seismic hazard analysis is based on peak ground
acceleration (PGA), which is the most common criterion in designing
of buildings. A catalogue of seismic events that includes both
historical and instrumental events was developed and covers the
period from 840 to 2009. The seismic sources that affect the hazard
in Naghan were identified within the radius of 200 km and the
recurrence relationships of these sources were generated by Kijko
and Sellevoll. Finally Peak Ground Horizontal Acceleration (PGHA)
has been prepared to indicate the earthquake hazard of Naghan for
different hazard levels by using SEISRISK III software.
Abstract: A satured liquid is warmed until boiling in a parallelepipedic boiler. The heat is supplied in a liquid through the horizontal bottom of the boiler, the other walls being adiabatic. During the process of boiling, the liquid evaporates through its free surface by deforming it. This surface which subdivides the boiler into two regions occupied on both sides by the boiled liquid (broth) and its vapor which surmounts it. The broth occupying the region and its vapor the superior region. A two- fluids model is used to describe the dynamics of the broth, its vapor and their interface. In this model, the broth is treated as a monophasic fluid (homogeneous model) and form with its vapor adiphasic pseudo fluid (two-fluid model). Furthermore, the interface is treated as a zone of mixture characterized by superficial void fraction noted α* . The aim of this article is to describe the dynamics of the interface between the boiled fluid and its vapor within a boiler. The resolution of the problem allowed us to show the evolution of the broth and the level of the liquid.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: Data stream analysis is the process of computing
various summaries and derived values from large amounts of data
which are continuously generated at a rapid rate. The nature of a
stream does not allow a revisit on each data element. Furthermore,
data processing must be fast to produce timely analysis results. These
requirements impose constraints on the design of the algorithms to
balance correctness against timely responses. Several techniques
have been proposed over the past few years to address these
challenges. These techniques can be categorized as either dataoriented
or task-oriented. The data-oriented approach analyzes a
subset of data or a smaller transformed representation, whereas taskoriented
scheme solves the problem directly via approximation
techniques. We propose a hybrid approach to tackle the data stream
analysis problem. The data stream has been both statistically
transformed to a smaller size and computationally approximated its
characteristics. We adopt a Monte Carlo method in the approximation
step. The data reduction has been performed horizontally and
vertically through our EMR sampling method. The proposed method
is analyzed by a series of experiments. We apply our algorithm on
clustering and classification tasks to evaluate the utility of our
approach.