Abstract: This study focuses on the effect of pin taper tool ratio on friction stir welding of magnesium alloy AZ31. Two pieces of AZ31 alloy with thickness of 6 mm were friction stir welded by using the conventional milling machine. The shoulder diameter used in this experiment is fixed at 18 mm. The taper pin ratio used are varied at 6:6, 6:5, 6:4, 6:3, 6:2 and 6:1. The rotational speeds that were used in this study were 500 rpm, 1000 rpm and 1500 rpm, respectively. The welding speeds used are 150 mm/min, 200 mm/min and 250 mm/min. Microstructure observation of welded area was studied by using optical microscope. Equiaxed grains were observed at the TMAZ and stir zone indicating fully plastic deformation. Tool pin diameter ratio 6/1 causes low heat input to the material because of small contact surface between tool surface and stirred materials compared to other tool pin diameter ratio. The grain size of stir zone increased with increasing of ratio of rotational speed to transverse speed due to higher heat input. It is observed that worm hole is produced when excessive heat input is applied. To evaluate the mechanical properties of this specimen, tensile test was used in this study. Welded specimens using taper pin ratio 6:1 shows higher tensile strength compared to other taper pin ratio up to 204 MPa. Moreover, specimens using taper pin ratio 6:1 showed better tensile strength with 500 rpm of rotational speed and 150mm/min welding speed.
Abstract: Problems of food security and the preservation of
reserved zones in the region of Central Asia under the conditions of
the climate change induced by the placement and construction of
large reservoirs are considered. The criteria for the optimum
placement and construction of reservoirs that entail the minimum
impact on the environment are established. The need for the
accounting of climatic parameters is shown by the calculation of the
water quantity required for the irrigation of agricultural lands.
Abstract: This research provides a systematic way to study and
better understand double nano-tubular structure of alunina (Al2O3) and
titania (TiO2). The TiO2 NT was prepared by immersing Al2O3
template in 0.02 M titanium fluoride (TiF4) solution (pH=3) at 25 °C
for 120 min, followed by annealing at 450 °C for 1 h to obtain anatase
TiO2 NT in the Al2O3 template. Large-scale development of film for
nanotube-based CO2 capture and conversion can potentially result in
more efficient energy harvesting. In addition, the production process
will be relatively environmentally friendly. The knowledge generated
by this research will significantly advance research in the area of
Al2O3, TiO2, CaO, and Ca2O3 nano-structure film fabrication and
applications for CO2 capture and conversion. This green energy source
will potentially reduce reliance on carbon-based energy resources and
increase interest in science and engineering careers.
Abstract: Social entrepreneurship is a new and exciting topic
that holds a great promise in helping alleviate the social problems of
the world. As a new subject, the meaning of the term is too broad and
this is counterproductive in trying to build understanding around the
concept. The purpose of this study is to identify and compare the
elements of social entrepreneurship as defined by seven international
organizations leading social entrepreneurship projects: Ashoka
Foundation, Skoll Foundation, Schwab Foundation and Yunus
Center; as well as from three other institutions fostering social
entrepreneurship: Global Social Benefit Institute, BRAC University,
and Socialab. The study used document analysis from Skoll
Foundation, Schwab Foundation, Yunus Center and Ashoka
Foundation; and open ended interview to experts from the Global
Social Benefit Institute at Santa Clara University in United States,
BRAC University from Bangladesh, and Socialab from Argentina.
The study identified three clearly differentiated schools of thought,
based on their views on revenue, scalability, replicability and
geographic location. While this study is by no means exhaustive, it
provides an indication of the patterns of ideas fostered by important
players in the field. By clearly identifying the similarities and
differences in the concept of social entrepreneurship, research and
practitioners are better equipped to build on the subject, and to
promote more adequate and accurate social policies to foster the
development of social entrepreneurship.
Abstract: This paper presents the trajectory tracking control of a
spatial redundant hybrid manipulator. This manipulator consists of
two parallel manipulators which are a variable geometry truss (VGT)
module. In fact, each VGT module with 3-degress of freedom (DOF)
is a planar parallel manipulator and their operational planes of these
VGT modules are arranged to be orthogonal to each other. Also, the
manipulator contains a twist motion part attached to the top of the
second VGT module to supply the missing orientation of the endeffector.
These three modules constitute totally 7-DOF hybrid
(parallel-parallel) redundant spatial manipulator. The forward
kinematics equations of this manipulator are obtained, then,
according to these equations, the inverse kinematics is solved based
on an optimization with the joint limit avoidance. The dynamic
equations are formed by using virtual work method. In order to test
the performance of the redundant manipulator and the controllers
presented, two different desired trajectories are followed by using the
computed force control method and a switching control method. The
switching control method is combined with the computed force
control method and genetic algorithm. In the switching control
method, the genetic algorithm is only used for fine tuning in the
compensation of the trajectory tracking errors.
Abstract: Introduction: Craniopharyngiomas (CPs) are rare epithelial tumors located mainly in the sellar/parasellar region. CPs have been classified histopathologically, genetically, clinically and prognostically into two distinctive subtypes: adamantinomatous and papillary variants. Aim: To examine the pattern of expression of both the β-catenin and epidermal growth factor receptor (EGFR) in surgically resected samples of adamantinomatous CP, and to asses for the possibility of using anti-EGFR in the management of ACP patients. Materials and methods: β-catenin and EGFR immunostaining was performed on paraffin-embedded tissue sections of 18 ACP cases. Result: 17 out of 18 cases (94%) of ACP exhibited strong nuclear/cytoplasmic expression of β-catenin, 15 (83%) of APC cases were positive for EGFR. Conclusion: Nuclear accumulation of β-catenin is a diagnostic hallmark of ACP. EGFR positivity in most cases of ACP could qualify the use of anti-EGFR therapy.
Abstract: Within Vietnam's system of higher education, its
schools of business play a vital role in supporting the country’s
economic objectives. However, the crucial contribution of soft skills
for maximal success within the business sector has to date not been
adequately recognized by its business schools. This being so, the
development of the business school curriculum in Vietnam has not
been able to 'catch up', so to say, with the burgeoning need of
students for a comprehensive soft skills program designed to meet the
national and global business objectives of their potential employers.
The burden of the present paper is first to reveal the results of our
survey in Vietnam which make explicit the extent to which major
Vietnamese industrial employers’ value the potential role that soft
skill competencies can play in maximizing business success. Our
final task will be to determine which soft skills employers discern as
best serving to maximize the economic interests of Vietnam within
the global marketplace. Semi-structured telephone interviews have
been conducted with the 15 representative Head Employers of
Vietnam's reputedly largest and most successful of the diverse
business enterprises across Vietnam. The findings of the study
indicate that all respondents highly value the increasing importance
of soft skills in business success. Our critical analysis of respondent
data reveals that 19 essential soft skills are deemed by employers as
integral to business workplace efficacy and should thus be integrated
into the formal business curriculum. We are confident that our study
represents the first comprehensive and specific survey yet undertaken
within the business sector in Vietnam which accesses and analyses
the opinions of representative employers from major companies
across the country in regard to the growing importance of 19 specific
soft skills essential for maximizing overall business success. Our
research findings also reveal that the integration into business school
curriculums nationwide of the soft skills we have identified is of
paramount importance to advance the national and global economic
interests of Vietnam.
Abstract: The technological paradigm of the disaster
management field, especially in the case of governmental
intervention strategies, is generally based on rapid and flexible
accommodation solutions. From various technical solution patterns
used to address the immediate housing needs of disaster victims, the
adaptive re-use of existing buildings can be considered to be both
low-cost and practical. However, there is a scarcity of analytical
methods to screen, select and adapt buildings to help decision makers
in cases of emergency. Following an extensive literature review, this
paper aims to highlight key points and problem areas associated with
the adaptive re-use of buildings within the disaster management
context. In other disciplines such as real estate management, the
adaptive re-use potential (ARP) of existing buildings is typically
based on the prioritization of a set of technical and non-technical
criteria which are then weighted to arrive at an economically viable
investment decision. After a disaster, however, the assessment of the
ARP of buildings requires consideration of different/additional layers
of analysis which stem from general disaster management principles
and the peculiarities of different types of disasters, as well as of their
victims. In this paper, a discussion of the development of an adaptive
re-use potential (ARP) assessment model is presented. It is thought
that governmental and non-governmental decision makers who are
required to take quick decisions to accommodate displaced masses
following disasters are likely to benefit from the implementation of
such a model.
Abstract: Imazu Bay plays an important role for endangered
species such as horseshoe crabs and black-faced spoonbills that stay in
the bay for spawning or the passing of winter. However, this bay is
semi-enclosed with slow water exchange, which could lead to
eutrophication under the condition of excess nutrient inflow to the bay.
Therefore, quantification of nutrient inflow is of great importance.
Generally, analysis of nutrient inflow to the bays takes into
consideration nutrient inflow from only the river, but that from
groundwater should not be ignored for more accurate results. The main
objective of this study is to estimate the amounts of nutrient inflow
from river and groundwater to Imazu Bay by analyzing water budget
in Zuibaiji River Basin and loads of T-N, T-P, NO3-N and NH4-N. The
water budget computation in the basin is performed using groundwater
recharge model and quasi three-dimensional two-phase groundwater
flow model, and the multiplication of the measured amount of nutrient
inflow with the computed discharge gives the total amount of nutrient
inflow to the bay. In addition, in order to evaluate nutrient inflow to the
bay, the result is compared with nutrient inflow from geologically
similar river basins. The result shows that the discharge is 3.50×107
m3/year from the river and 1.04×107 m3/year from groundwater. The
submarine groundwater discharge accounts for approximately 23 % of
the total discharge, which is large compared to the other river basins. It
is also revealed that the total nutrient inflow is not particularly large.
The sum of NO3-N and NH4-N loadings from groundwater is less than
10 % of that from the river because of denitrification in groundwater.
The Shin Seibu Sewage Treatment Plant located below the observation
points discharges treated water of 15,400 m3/day and plans to increase
it. However, the loads of T-N and T-P from the treatment plant are 3.9
mg/L and 0.19 mg/L, so that it does not contribute a lot to
eutrophication.
Abstract: There is an increasing demand for developing urban
land to provide better living conditions for all citizens in Afghanistan.
Most of the development will involve the acquisition of land. And the
current land acquisition method practiced by central government is
expropriation, which is a cash-based transaction method that imposes
heavy fiscal burden on local municipalities and central government,
and it does not protect ownership rights and social equity of
landowners besides it relocates the urban poor to remote areas with
limited access to jobs and public services. The questionnaire analysis,
backed by observations of different case studies in countries where
land readjustment is used as a collaborative land development tool
indicates that the method plays a key role in valuing landowners’
rights, giving other community members and stakeholders the
opportunity to collaboratively implement urban development
projects. The practice of the method is reducing the heavy fiscal
burden on the local and central governments and is a better option to
deal with the current development challenges in Afghanistan.
Abstract: Waste polyethylene (PE) is classified as waste low
density polyethylene (LDPE) and waste high density polyethylene
(HDPE) according to their densities. Pyrolysis of plastic waste may
have an important role in dealing with the enormous amounts of
plastic waste produced all over the world, by decreasing their
negative impact on the environment. This waste may be converted
into economically valuable hydrocarbons, which can be used both as
fuels and as feed stock in the petrochemical industry. End product
yields and properties depend on the plastic waste composition.
Pyrolytic biochar is one of the most important products of waste
plastics pyrolysis. In this study, HDPE and LDPE plastic wastes were
co-pyrolyzed together with waste olive pomace. Pyrolysis runs were
performed at temperature 700°C with heating rates of 5°C/min.
Higher pyrolysis oil and gas yields were observed by the using waste
olive pomace. The biochar yields of HDPE- olive pomace and LDPEolive
pomace were 6.37% and 7.26% respectively for 50% olive
pomace doses. The calorific value of HDPE-olive pomace and
LDPE-olive pomace of pyrolysis oil were 8350 and 8495 kCal.
Abstract: With the increasing complexity of cyberspace security, the cyber-attack attribution has become an important challenge of the security protection systems. The difficult points of cyber-attack attribution were forced on the problems of huge data handling and key data missing. According to this situation, this paper presented a reasoning method of cyber-attack attribution based on threat intelligence. The method utilizes the intrusion kill chain model and Bayesian network to build attack chain and evidence chain of cyber-attack on threat intelligence platform through data calculation, analysis and reasoning. Then, we used a number of cyber-attack events which we have observed and analyzed to test the reasoning method and demo system, the result of testing indicates that the reasoning method can provide certain help in cyber-attack attribution.
Abstract: Solid particle erosion has been identified as a critical wear phenomenon which takes place during operation of aeroengines in dusty environment. The present work discusses the erosion behavior of Ti-44.5Al-6.25Nb-0.8Mo-0.1B alloy (TNB-V4) which finds its application in low pressure gas turbines and can be used for high pressure compressors too. Prior to the erosion tests, the alloy was heat treated to improve the mechanical properties. Afterwards, specimens were eroded at impact angles of 30° and 90° at room and high temperatures (100 °C-400 °C). Volume loss and erosion behavior are studied through gravimetric analysis, whereas erosion mechanisms are characterized through scanning electron microscopy. The results indicate a clear difference in the erosion mechanism for different impact angles. The influence of the test temperature on the erosion behavior of the alloy is also discussed in the present contribution.
Abstract: Edge detection is one of the most important tasks in image processing. Medical image edge detection plays an important role in segmentation and object recognition of the human organs. It refers to the process of identifying and locating sharp discontinuities in medical images. In this paper, a neuro-fuzzy based approach is introduced to detect the edges for noisy medical images. This approach uses desired number of neuro-fuzzy subdetectors with a postprocessor for detecting the edges of medical images. The internal parameters of the approach are optimized by training pattern using artificial images. The performance of the approach is evaluated on different medical images and compared with popular edge detection algorithm. From the experimental results, it is clear that this approach has better performance than those of other competing edge detection algorithms for noisy medical images.
Abstract: In this paper, x-ray impact of Taguchi method and design of experiment philosophy to project relationship between various factors leading to output yield strength of rebar is studied. In bar mill of an integrated steel plant, there are two production lines called as line 1 and line 2. The metallic properties e.g. yield strength of finished product of the same material is varying for a particular grade material when rolled simultaneously in both the lines. A study has been carried out to set the process parameters at optimal level for obtaining equal value of yield strength simultaneously for both lines.
Abstract: Lightweight construction became more and more important over the last decades in several applications, e.g. in the automotive or aircraft sector. This is the result of economic and ecological constraints on the one hand and increasing safety and comfort requirements on the other hand. In the field of lightweight design, different approaches are used due to specific requirements towards the technical systems. The use of endless carbon fiber reinforced plastics (CFRP) offers the largest weight saving potential of sometimes more than 50% compared to conventional metal-constructions. However, there are very limited industrial applications because of the cost-intensive manufacturing of the fibers and production technologies. Other disadvantages of pure CFRP-structures affect the quality control or the damage resistance. One approach to meet these challenges is hybrid materials. This means CFRP and sheet metal are combined on a material level. Therefore, new opportunities for innovative process routes are realizable. Hybrid lightweight design results in lower costs due to an optimized material utilization and the possibility to integrate the structures in already existing production processes of automobile manufacturers. In recent and current research, the advantages of two-layered hybrid materials have been pointed out, i.e. the possibility to realize structures with tailored mechanical properties or to divide the curing cycle of the epoxy resin into two steps. Current research work at the Chair for Automotive Lightweight Design (LiA) at the Paderborn University focusses on production processes for fiber-metal-laminates. The aim of this work is the development and qualification of a large-scale production process for high-performance fiber-metal-laminates (FML) for industrial applications in the automotive or aircraft sector. Therefore, the prepreg-press-technology is used, in which pre-impregnated carbon fibers and sheet metals are formed and cured in a closed, heated mold. The investigations focus e.g. on the realization of short process chains and cycle times, on the reduction of time-consuming manual process steps, and the reduction of material costs. This paper gives an overview over the considerable steps of the production process in the beginning. Afterwards experimental results are discussed. This part concentrates on the influence of different process parameters on the mechanical properties, the laminate quality and the identification of process limits. Concluding the advantages of this technology compared to conventional FML-production-processes and other lightweight design approaches are carried out.
Abstract: Operators of vessel traffic service (VTS) center provides three different types of services; namely information service, navigational assistance and traffic organization to vessels. To provide these services, operators monitor vessel traffic through computer interface and provide navigational advice based on the information integrated from multiple sources, including automatic identification system (AIS), radar system, and closed circuit television (CCTV) system. Therefore, this information is crucial in VTS operation. However, what information the VTS operator actually need to efficiently and properly offer services is unclear. The aim of this study is to investigate into information requirements for VTS operation. To achieve this aim, field observation was carried out to elicit the information requirements for VTS operation. The study revealed that the most frequent and important tasks were handling arrival vessel report, potential conflict control and abeam vessel report. Current location and vessel name were used in all tasks. Hazard cargo information was particularly required when operators handle arrival vessel report. The speed, the course, and the distance of two or several vessels were only used in potential conflict control. The information requirements identified in this study can be utilized in designing a human-computer interface that takes into consideration what and when information should be displayed, and might be further used to build the foundation of a decision support system for VTS.
Abstract: In this paper, we consider CCL-N (Cooperative Cross Layer Network) topology based on the cross layer (both centralized and distributed) environment to form network communities. Various performance metrics related to the IEEE 802.16 networks are discussed to design CCL-N Topology. In CCL-N topology, nodes are classified as master nodes (Master Base Station [MBS]) and serving nodes (Relay Station [RS]). Nodes communities are organized based on the networking terminologies. Based on CCL-N Topology, various simulation analyses for both transparent and non-transparent relays are tabulated and throughput efficiency is calculated. Weighted load balancing problem plays a challenging role in IEEE 802.16 network. CoTS (Concurrent Transmission Scheduling) Scheme is formulated in terms of three aspects – transmission mechanism based on identical communities, different communities and identical node communities. CoTS scheme helps in identifying the weighted load balancing problem. Based on the analytical results, modularity value is inversely proportional to that of the error value. The modularity value plays a key role in solving the CoTS problem based on hop count. The transmission mechanism for identical node community has no impact since modularity value is same for all the network groups. In this paper three aspects of communities based on the modularity value which helps in solving the problem of weighted load balancing and CoTS are discussed.
Abstract: An online advertisement system and its implementation
for the Yioop open source search engine are presented. This system
supports both selling advertisements and displaying them within
search results. The selling of advertisements is done using a system
to auction off daily impressions for keyword searches. This is an
open, ascending price auction system in which all accepted bids will
receive a fraction of the auctioned day’s impressions. New bids in
our system are required to be at least one half of the sum of all
previous bids ensuring the number of accepted bids is logarithmic
in the total ad spend on a keyword for a day. The mechanics of
creating an advertisement, attaching keywords to it, and adding it
to an advertisement inventory are described. The algorithm used to
go from accepted bids for a keyword to which ads are displayed at
search time is also presented. We discuss properties of our system
and compare it to existing auction systems and systems for selling
online advertisements.
Abstract: There is a requirement for registered edible seed pumpkin suitable for eating in Turkey. A total of 81 genotypes collected from the researchers in 2005 originated from Eskisehir, Konya, Nevsehir, Tekirdag, Sakarya, Kayseri and Kirsehir provinces were utilized. The used genetic materials were brought to S5 generation by the research groups among 2006 and 2010 years. In this research, S5 stage reached in the genotype given some of the morphological features, and selection of promising genotypes generated scale were made. Results showed that the A-1 (420), A-7 (410), A-8 (420), A-32 (420), B-17 (410), B-24 (410), B-25 (420), B-33 (400), C-24 (420), C-25 (410), C-26 (410) and C-30 (420) genotypes are expected to be promising varieties.