Abstract: The surface water used in this study was collected from the Chao Praya River at the lower part at the Nonthaburi bridge. It was collected and used throughout the experiment. TOC (also known as DOC) in the range between 2.5 to 5.6 mg/l were investigated in this experiment. The use of conventional treatment methods such as FeCl3 and PAC showed that TOC removal was 65% using FeCl3 and 78% using PAC (powder activated carbon). The advanced oxidation process alone showed only 35% removal of TOC. Coupling advanced oxidation with a small amount of PAC (0.05g/L) increased efficiency by upto 55%. The combined BAC with advanced oxidation process and small amount of PAC demonstrated the highest efficiency of up to 95% of TOC removal and lower sludge production compared with other methods.
Abstract: In a lowland dipterocarp forest, we assessed the impact of canopy openness (CO) and the resultant changes under different logging systems using hemispherical photography. CO was assessed in a primary forest and two forests logged selectively using reduced impact logging. At one site, 3-m-wide strip cutting was conducted for line planting. From the comparison of CO among the three sites, we found significant changes caused by logging. However, no significant difference was observed between the two logged sites. Strip cutting treatment did not affect CO. One year after, significant canopy closure occurred in both of the logged sites. Canopy closure was significant regardless of the disturbance element, logging gap, skid trail, or strip cutting line. Significant establishment of seedlings within a year was observed in the strip cutting line. Seedling establishment seemed to contribute to rapid canopy closure and prospected to affect to the survival and growth of planted trees.
Abstract: The Euler-s equation of motion is extended to include
the viscosity stress tensor leading to the formulation of Navier–
Stokes type equation. The latter is linearized and applied to
investigate the rotational motion or vorticity in a viscous fluid.
Relations for the velocity of viscous waves and attenuation parameter
are obtained in terms of viscosity (μ) and the density (¤ü) of the fluid.
μ and ¤ü are measured experimentally as a function of temperature for
two different samples of light and heavy crude oil. These data
facilitated to determine the activation energy, velocity of viscous
wave and the attenuation parameter. Shear wave velocity in heavy oil
is found to be much larger than the light oil, whereas the attenuation
parameter in heavy oil is quite low in comparison to light one. The
activation energy of heavy oil is three times larger than light oil.
Abstract: The analytical solutions for geodesic acoustic
eigenmodes in tokamak plasmas with circular concentric magnetic
surfaces are found. In the frame of ideal magnetohydrodynamics the
dispersion relation taking into account the toroidal coupling between
electrostatic perturbations and electromagnetic perturbations with
poloidal mode number |m| = 2 is derived. In the absence of such
a coupling the dispersion relation gives the standard continuous
spectrum of geodesic acoustic modes. The analysis of the existence
of global eigenmodes for plasma equilibria with both off-axis
and on-axis maximum of the local geodesic acoustic frequency is
performed.
Abstract: This paper is a numerical investigation of a laminar
isothermal plane two dimensional wall jet. Special attention has been
paid to the effect of the inlet conditions at the nozzle exit on the
hydrodynamic and thermal characteristics of the flow. The
behaviour of various fluids evolving in both forced and mixed
convection regimes near a vertical plate plane is carried out. The
system of governing equations is solved with an implicit finite
difference scheme. For numerical stability we use a staggered non
uniform grid. The obtained results show that the effect of the Prandtl
number is significant in the plume region in which the jet flow is
governed by buoyant forces. Further for ascending X values, the
buoyancy forces become dominating, and a certain agreement
between the temperature profiles are observed, which shows that the
velocity profile has no longer influence on the wall temperature
evolution in this region. Fluids with low Prandtl number warm up
more importantly, because for such fluids the effect of heat diffusion
is higher.
Abstract: Missing data is a persistent problem in almost all
areas of empirical research. The missing data must be treated very
carefully, as data plays a fundamental role in every analysis.
Improper treatment can distort the analysis or generate biased results.
In this paper, we compare and contrast various imputation techniques
on missing data sets and make an empirical evaluation of these
methods so as to construct quality software models. Our empirical
study is based on NASA-s two public dataset. KC4 and KC1. The
actual data sets of 125 cases and 2107 cases respectively, without
any missing values were considered. The data set is used to create
Missing at Random (MAR) data Listwise Deletion(LD), Mean
Substitution(MS), Interpolation, Regression with an error term and
Expectation-Maximization (EM) approaches were used to compare
the effects of the various techniques.
Abstract: Avoiding learning failures in mathematics e-learning environments caused by emotional problems in students with autism has become an important topic for combining of special education with information and communications technology. This study presents an adaptive emotional adjustment model in mathematics e-learning for students with autism, emphasizing the lack of emotional perception in mathematics e-learning systems. In addition, an emotion classification for students with autism was developed by inducing emotions in mathematical learning environments to record changes in the physiological signals and facial expressions of students. Using these methods, 58 emotional features were obtained. These features were then processed using one-way ANOVA and information gain (IG). After reducing the feature dimension, methods of support vector machines (SVM), k-nearest neighbors (KNN), and classification and regression trees (CART) were used to classify four emotional categories: baseline, happy, angry, and anxious. After testing and comparisons, in a situation without feature selection, the accuracy rate of the SVM classification can reach as high as 79.3-%. After using IG to reduce the feature dimension, with only 28 features remaining, SVM still has a classification accuracy of 78.2-%. The results of this research could enhance the effectiveness of eLearning in special education.
Abstract: A gene network gives the knowledge of the regulatory
relationships among the genes. Each gene has its activators and
inhibitors that regulate its expression positively and negatively
respectively. Genes themselves are believed to act as activators and
inhibitors of other genes. They can even activate one set of genes and
inhibit another set. Identifying gene networks is one of the most
crucial and challenging problems in Bioinformatics. Most work done
so far either assumes that there is no time delay in gene regulation or
there is a constant time delay. We here propose a Dynamic Time-
Lagged Correlation Based Method (DTCBM) to learn the gene
networks, which uses time-lagged correlation to find the potential
gene interactions, and then uses a post-processing stage to remove
false gene interactions to common parents, and finally uses dynamic
correlation thresholds for each gene to construct the gene network.
DTCBM finds correlation between gene expression signals shifted in
time, and therefore takes into consideration the multi time delay
relationships among the genes. The implementation of our method is
done in MATLAB and experimental results on Saccharomyces
cerevisiae gene expression data and comparison with other methods
indicate that it has a better performance.
Abstract: Nonlinear propagation of ion-acoustic waves in a selfgravitating
dusty plasma consisting of warm positive ions,
isothermal two-temperature electrons and negatively charged dust
particles having charge fluctuations is studied using the reductive
perturbation method. It is shown that the nonlinear propagation of
ion-acoustic waves in such plasma can be described by an uncoupled
third order partial differential equation which is a modified form of
the usual Korteweg-deVries (KdV) equation. From this nonlinear
equation, a new type of solution for the ion-acoustic wave is
obtained. The effects of two-temperature electrons, gravity and dust
charge fluctuations on the ion-acoustic solitary waves are discussed
with possible applications.
Abstract: The main objective developed in this paper is to find a
graphic technique for modeling, simulation and diagnosis of the
industrial systems. This importance is much apparent when it is about
a complex system such as the nuclear reactor with pressurized water
of several form with various several non-linearity and time scales. In
this case the analytical approach is heavy and does not give a fast
idea on the evolution of the system. The tool Bond Graph enabled us
to transform the analytical model into graphic model and the
software of simulation SYMBOLS 2000 specific to the Bond Graphs
made it possible to validate and have the results given by the
technical specifications. We introduce the analysis of the problem
involved in the faults localization and identification in the complex
industrial processes. We propose a method of fault detection applied
to the diagnosis and to determine the gravity of a detected fault. We
show the possibilities of application of the new diagnosis approaches
to the complex system control. The industrial systems became
increasingly complex with the faults diagnosis procedures in the
physical systems prove to become very complex as soon as the
systems considered are not elementary any more. Indeed, in front of
this complexity, we chose to make recourse to Fault Detection and
Isolation method (FDI) by the analysis of the problem of its control
and to conceive a reliable system of diagnosis making it possible to
apprehend the complex dynamic systems spatially distributed applied
to the standard pressurized water nuclear reactor.
Abstract: Green supply chain management is an increasingly recognized practice among companies that are seeking to improve environmental performance. Of particular concern is how to arouse organizational awareness and put green activities into practice in
order to enhance manufacturing performances. This paper investigates the correlation of green supply chain practices and
manufacturing performances in Malaysian certified MS ISO 14000 manufacturing firms. The findings shows that green supply chain
practices which that can be denominated product recycling, environmental compliance and optimization have significant influence to some of the manufacturing performances.
Abstract: The objective of the present work is to conduct
investigations leading to a more complete explanation of single phase
natural convective heat transfer in an enclosure with fin utilizing
nano fluids. The nano fluid used, which is composed of Aluminum
oxide nano particles in suspension of Ethylene glycol, is provided at
various volume fractions. The study is carried out numerically for a
range of Rayleigh numbers, fin heights and aspect ratio. The flow and
temperature distributions are taken to be two-dimensional. Regions
with the same velocity and temperature distributions are identified as
symmetry of sections. One half of such a rectangular region is chosen
as the computational domain taking into account the symmetry about
the fin. Transport equations are modeled by a stream functionvorticity
formulation and are solved numerically by finite-difference
schemes. Comparisons with previously published works on the basis
of special cases are done. Results are presented in the form of
streamline, vector and isotherm plots as well as the variation of local
Nusselt number along the fin under different conditions.
Abstract: An active suspension system has been proposed to
improve the ride comfort. A quarter-car 2 degree-of-freedom (DOF)
system is designed and constructed on the basis of the concept of a
four-wheel independent suspension to simulate the actions of an
active vehicle suspension system. The purpose of a suspension
system is to support the vehicle body and increase ride comfort. The
aim of the work described in the paper was to illustrate the
application of fuzzy logic technique to the control of a continuously
damping automotive suspension system. The ride comfort is
improved by means of the reduction of the body acceleration caused
by the car body when road disturbances from smooth road and real
road roughness.
The paper describes also the model and controller used in the
study and discusses the vehicle response results obtained from a
range of road input simulations. In the conclusion, a comparison of
active suspension fuzzy control and Proportional Integration
derivative (PID) control is shown using MATLAB simulations.
Abstract: The objective of this research seeks to transmit a distance training model to the community in the upper northeastern region. The group sampling consists of 60 community leaders in the municipality of sub-district Kumphawapi, Kumphawapi Disrict, Udonthani Province. The research tools rely on the following instruments, they are : 1) the achievement test of community leaders- training and 2) the satisfaction questionnaires of community leaders. The statistics used in data analysis takes the statistical mean, percentage, standard deviation, and statistical T-test. The resulted findings reveal : 1) the efficiency of the distance training developed by the researcher for the community leaders joining in the training received the average score between in-training and post-training period higher than the setup criterion, 2) the two groups of participants in the training achieved higher knowledge than their pre-training state, 3) the comparison of the achievements between the two group presented no different results, 4) the community leaders obtained the high-to-highest satisfaction.
Abstract: The objectives of this study are to determine the
effects of soil cover type on characteristics of leachates generated
from landfill lysimeters. Four lysimeters with diameter and height
of 0.15 and 3.00 m, respectively, were prepared. Three lysimeters
were filled with municipal waste and three different cover soil types
i.e. sandy loam soil, silty loam soil and clay soil while another
lysimeter was filled solely with municipal waste. The study was
conducted in the rainy season. Leachate quantities were measured
every day and leachate characteristics were determined once a week.
The cumulative leachate quantity from the lysimeter filled solely
with municipal waste was found to be around 27% higher than the
lysimeters using cover soils. There were no any differences of the
cumulative leachate amounts generated from the lysimeters using
three types of soils. The comparison of the total mass of pollutants
generated from all lysimeters showed that the lysimeter filled solely
with municipal waste generated the maximum quantities of
pollutants. Among the lysimeters using different types of soils, the
lysimeter using sandy loam soil generated the lowest amount of most
of pollutants, compared with the lysimeters using silty loam and clay
soils. It can be concluded that in term of pollutant attenuation in the
leachate, a sandy loam is the most suitable soil to be used as a cover
soil in the landfill.
Abstract: Polymer melt compressibility and mold surface roughness, which are generally ignored during the filling stage of the conventional injection molding, may become increasingly significant in micro injection molding where the parts become smaller. By employing the 2.5D generalized Hele-Shaw model, we presented here the effects of polymer compressibility and mold surface roughness on mold-filling in a micro-thickness cavity. To elucidate the effects of surface roughness, numerical investigations were conducted using a cavity flat plate which has two halves with different surface roughness. This allows the comparison of flow field on two different halves under identical processing conditions but with different roughness. Results show that polymer compressibility and mold surface roughness have effects on mold filling in micro injection molding. There is in shrinkage reduction as the density is increased due to polymer melt compressibility during the filling stage.
Abstract: Simulation of occlusal function during laboratory
material-s testing becomes essential in predicting long-term
performance before clinical usage. The aim of the study was to assess
the influence of chamfer preparation depth on failure risk of heat
pressed ceramic crowns with and without zirconia framework by
means of finite element analysis. 3D models of maxillary central
incisor, prepared for full ceramic crowns with different depths of the
chamfer margin (between 0.8 and 1.2 mm) and 6-degree tapered
walls together with the overlying crowns were generated using
literature data (Fig. 1, 2). The crowns were designed with and
without a zirconia framework with a thickness of 0.4 mm. For all
preparations and crowns, stresses in the pressed ceramic crown,
zirconia framework, pressed ceramic veneer, and dentin were
evaluated separately. The highest stresses were registered in the
dentin. The depth of the preparations had no significant influence on
the stress values of the teeth and pressed ceramics for the studied
cases, only for the zirconia framework. The zirconia framework
decreases the stress values in the veneer.
Abstract: Bacterial magnetic nanoparticles have great useful potential in biotechnological and biomedical applications. In this study, a liquid growth medium was modified for cultivation a fastidious magnetotactic bacterium that has been isolated from Anzali
lagoon, Iran in our previous research. These modifications include
change in vitamin, mineral, carbon sources and etcetera. In our
experience, the serum bottles and designed air-tight laboratory bottles
were used to create microaerobic conditions in order to development
of a method for scale-up experiment. This information may serve as a
guide to green chemistry based biological protocols for the synthesis
of magnetic nanoparticles with control over the chemical
composition, morphology and size.
Abstract: In this research, a latent class vector model for pairwise data is formulated. As compared to the basic vector model, this model yields consistent estimates of the parameters since the number of parameters to be estimated does not increase with the number of subjects. The result of the analysis reveals that the model was stable and could classify each subject to the latent classes representing the typical scales used by these subjects.
Abstract: Recently, the design is becoming important in product development. The technology which is a strong point of Japan is immediately caught up by the foreign countries, and the price competition begins. Therefore companies tend to plan differentiation of products by the design or a color. The purpose of my work was to consider the optimal color for using by product development. We needed to clarify the thing leading to color preference for this purpose. Two kinds of investigations were made. By the first investigation, we found out that a geographical factor difference existed in color preference. Then, investigation which regarded the difference as latitude was conducted. However, the result expected from the difference in latitude was not obtained. It seems that it is necessary to set up difference of latitude a little more greatly, or to reexamine by other geographical factors.