Abstract: The present experimental investigation brings about
a comparative study of lactic acid production by pure strains of
Lactobacilli (1) L. delbreuckii (NCIM2025), (2) L. pentosus (NCIM
2912), (3) Lactobacillus sp.(NCIM 2734, (4) Lactobacillus sp.
(NCIM2084) and coculture of strain-1 and Stain-2 in solid bed of
wheat bran, under the influence of different nitrogen sources such as
baker-s yeast, meat extract and proteose peptone. Among the pure
cultures, strain-3 attained lowest pH value of 3.44, hence highest acid
formation 46.41 g/L, while the coculture attained an overall
maximum value 47.56 g/L lactic acid (pH 3.38) at 15 g/L and 20 g/L
level of baker-s yeast, respectively.
Abstract: The Bangnanglee Sub-district Administrative Office,
Thailand had initiated a policy to environmental protection with
encouraging household waste management in order to promote civil
responsibility for domestic hygienic. This research studied the
household behaviors on solid waste and wastewater management. A
sample population of 306 families answered a questionnaire. The
study showed that, on average, domestic activities had produced 1.93
kilograms of waste per household per day. It has been found that 79%
of the households made several attempts to reduce their own amount
of waste. 80% of the households stationed their own garbage bins.
71% managed their waste by selling recyclable products. As for the
rest of the waste, 51% burned them, while 29% disposed their waste
in the nearby public trashcans and other 13% have them buried. As
for wastewater, 60% of the households disposed it into the sewage,
whereas 30% disposed them right from their elevated house.
Abstract: Structured phospholipids from commercial soybean
lecithin with oil enriched omega-3 fatty acid form by product of tuna
canning is alternative procedure to provides the stability of omega-3
fatty acid structure and increase these bioactive function in
metabolism. Best treatment condition was obtain in 18 hours
acidolysis reaction with 30% enzyme concentration, which EPADHA
incorporation level was 127,47 mg/g and incorporation
percentage of EPA-DHA was 51,04% at phospholipids structure.
This structured phospolipids could reduce atherosclerosis risk in
male Sprague dawley rat. Provision of structured phospholipids has
significant effect (α = 0.05) on changes in lipid profile, intima-media
thickness of aorta rats (male Sprague dawley) fed atherogenic diet.
Structured phospholipids intake can lower total cholesterol 78.36
mg/dL, total triglycerides 94,57 mg/dL, LDL levels 87.08 mg/dL and
increased HDL level as much as 12,64 mg/dL in 10 weeks cares.
Structured phospholipids intake also can prevent the thickening of
the intima-media layer of the aorta.
Abstract: Mixed model assembly lines (MMAL) are a type of
production line where a variety of product models similar in product
characteristics are assembled. The effective design of these lines
requires that schedule for assembling the different products is
determined. In this paper we tried to fit the sequencing problem with
the main characteristics of make to order (MTO) environment. The
problem solved in this paper is a multiple objective sequencing
problem in mixed model assembly lines sequencing using weighted
Sum Method (WSM) using GAMS software for small problem and
an effective GA for large scale problems because of the nature of
NP-hardness of our problem and vast time consume to find the
optimum solution in large problems. In this problem three practically
important objectives are minimizing: total utility work, keeping a
constant production rate variation, and minimizing earliness and
tardiness cost which consider the priority of each customer and
different due date which is a real situation in mixed model assembly
lines and it is the first time we consider different attribute to
prioritize the customers which help the company to reduce the cost of
earliness and tardiness. This mechanism is a way to apply an advance
available to promise (ATP) in mixed model assembly line sequencing
which is the main contribution of this paper.
Abstract: Increasing the demand for effectively use of the
production facility requires the tools for sharing the manufacturing
facility through remote operation of the machining process. This
research introduces the methodology of machining technology for
direct remote operation of networked milling machine. The
integrated tools with virtual simulation, remote desktop protocol and
Setup Free Attachment for remote operation of milling process are
proposed. Accessing and monitoring of machining operation is
performed by remote desktop interface and 3D virtual simulations.
Capability of remote operation is supported by an auto setup
attachment with a reconfigurable pin type setup free technology
installed on the table of CNC milling machine to perform unattended
machining process. The system is designed using a computer server
and connected to a PC based controlled CNC machine for real time
monitoring. A client will access the server through internet
communication and virtually simulate the machine activity. The
result has been presented that combination between real time virtual
simulation and remote desktop tool is enabling to operate all machine
tool functions and as well as workpiece setup..
Abstract: The plastic flow of metal in the extrusion process is
an important factor in controlling the mechanical properties of the
extruded products. It is, however, difficult to predict the metal flow
in three dimensional extrusions of sections due to the involvement of
re-entrant corners. The present study is to find an upper bound
solution for the extrusion of triangular sectioned through taper dies
from round sectioned billet. A discontinuous kinematically
admissible velocity field (KAVF) is proposed. From the proposed
KAVF, the upper bound solution on non-dimensional extrusion
pressure is determined with respect to the chosen process parameters.
The theoretical results are compared with experimental results to
check the validity of the proposed velocity field. An extrusion setup
is designed and fabricated for the said purpose, and all extrusions are
carried out using circular billets. Experiments are carried out with
commercially available lead at room temperature.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: The fault detection and diagnosis of complicated
production processes is one of essential tasks needed to run the process
safely with good final product quality. Unexpected events occurred in
the process may have a serious impact on the process. In this work,
triangular representation of process measurement data obtained in an
on-line basis is evaluated using simulation process. The effect of using
linear and nonlinear reduced spaces is also tested. Their diagnosis
performance was demonstrated using multivariate fault data. It has
shown that the nonlinear technique based diagnosis method produced
more reliable results and outperforms linear method. The use of
appropriate reduced space yielded better diagnosis performance. The
presented diagnosis framework is different from existing ones in that it
attempts to extract the fault pattern in the reduced space, not in the
original process variable space. The use of reduced model space helps
to mitigate the sensitivity of the fault pattern to noise.
Abstract: Hydroxymethylfurfural (HMF) is formed by thermally
treating products rich in carbohydrates. HMF and other furan
derivatives are toxic.
The aim of the research was to establish the content of HMF in
gingerbread biscuits with honey and sugar syrup additives by using
three leavening agents— ammonium carbonate (NH4HCO3 and
(NH4)2CO3), baking powder, and baking soda (NaHCO3).
The content of HMF is significantly affected by the leavening
agent used. The content of HMF with honey where ammonium
carbonate was used as additive range from 5.7 to 27.3mg 100g-1, but
when sugar syrup is used the content varies from 2.3 to 7.4mg 100g-1.
When baking powder and baking soda are used as leavening agents,
the content of HMF exceeds 4mg 100g-1 in the event honey had been
added and the baking time had been longer (10 minutes at 180°C or
9 minutes at 200°C).
Abstract: The sand production problem has led researchers into making various attempts to understand the phenomenon. The generally accepted concept is that the occurrence of sanding is due to the in-situ stress conditions and the induced changes in stress that results in the failure of the reservoir sandstone during hydrocarbon production from wellbores. By using a hypothetical cased (perforated) well, an approach to the problem is presented here by using Finite Element numerical modelling techniques. In addition to the examination of the erosion problem, the influence of certain key parameters is studied in order to ascertain their effect on the failure and subsequent erosion process. The major variables investigated include: drawdown, perforation depth, and the erosion criterion. Also included is the determination of the optimal mud pressure for given operational and reservoir conditions. The improved understanding between parameters enables the choice of optimal values to minimize sanding during oil production.
Abstract: Tomato powder has good potential as substitute of tomato paste and other tomato products. In order to protect physicochemical properties and nutritional quality of tomato during dehydration process, investigation was carried out using different drying methods and pretreatments. Solar drier and continuous conveyor (tunnel) drier were used for dehydration where as calcium chloride (CaCl2), potassium metabisulphite (KMS), calcium chloride and potassium metabisulphite (CaCl2 +KMS), and sodium chloride (NaCl) selected for treatment.. lycopene content, dehydration ratio, rehydration ratio and non-enzymatic browning in addition to moisture, sugar and titrable acidity were studied. Results show that pre-treatment with CaCl2 and NaCl increased water removal and moisture mobility in tomato slices during drying of tomatoes. Where CaCl2 used along with KMS the NEB was recorded the least compared to other treatments and the best results were obtained while using the two chemicals in combination form. Storage studies in LDPE polymeric and metalized polyesters films showed less changes in the products packed in metallized polyester pouches and even after 6 months lycopene content did not decrease more than 20% as compared to the control sample and provide extension of shelf life in acceptable condition for 6 months. In most of the quality characteristics tunnel drier samples presented better values in comparison to solar drier.
Abstract: Dhaka, the capital city of Bangladesh, is one of the
densely populated cities in the world. Due to rapid urbanization 60%
of its population lives in slum and squatter settlements. The reason
behind this poverty is low economic growth, inequitable distribution
of income, unequal distribution of productive assets, unemployment
and underemployment, high rate of population growth, low level of
human resource development, natural disasters, and limited access to
public services. Along with poverty, creating pressure on urban land,
shelter, plots, open spaces this creates environmental and ecological
degradation. These constraints are mostly resulted from the failures
of the government policies and measures and only Government can
solve this problem. This is now prime time to establish planning and
environmental management policy and sustainable urban
development for the city and for the urban slum dwellers which are
free from eviction, criminals, rent seekers and other miscreants.
Abstract: Modeling product configurations needs large amounts of knowledge about technical and marketing restrictions on the product. Previous attempts to automate product configurations concentrate on representations and management of the knowledge for specific domains in fixed and isolated computing environments. Since the knowledge about product configurations is subject to continuous change and hard to express, these attempts often failed to efficiently manage and exchange the knowledge in collaborative product development. In this paper, XML Topic Map (XTM) is introduced to represent and exchange the knowledge about product configurations in collaborative product development. A product configuration model based on XTM along with its merger and inference facilities enables configuration engineers in collaborative product development to manage and exchange their knowledge efficiently. A prototype implementation is also presented to demonstrate the proposed model can be applied to engineering information systems to exchange the product configuration knowledge.
Abstract: Li1.5Al0.5Ti1.5 (PO4)3(LATP) has received much
attention as a solid electrolyte for lithium batteries. In this study, the
LATP solid electrolyte is prepared by the co-precipitation method
using Li3PO4 as a Li source. The LATP is successfully prepared and
the Li ion conductivities of bulk (inner crystal) and total (inner crystal
and grain boundary) are 1.1 × 10-3 and 1.1 × 10-4 S cm-1, respectively.
These values are comparable to the reported values, in which Li2C2O4
is used as the Li source. It is conclude that the LATP solid electrolyte
can be prepared by the co-precipitation method using Li3PO4 as the Li
source and this procedure has an advantage in mass production over
previous procedure using Li2C2O4 because Li3PO4 is lower price
reagent compared with Li2C2O4.
Abstract: Raisin Concentrate (RC) are the most important
products obtained in the raisin processing industries. These RC
products are now used to make the syrups, drinks and confectionery
productions and introduced as natural substitute for sugar in food
applications. Iran is a one of the biggest raisin exporter in the world
but unfortunately despite a good raw material, no serious effort to
extract the RC has been taken in Iran. Therefore, in this paper, we
determined and analyzed affected parameters on extracting RC
process and then optimizing these parameters for design the
extracting RC process in two types of raisin (round and long)
produced in Khorasan region. Two levels of solvent (1:1 and 2:1),
three levels of extraction temperature (60°C, 70°C and 80°C), and
three levels of concentration temperature (50°C, 60°C and 70°C)
were the treatments. Finally physicochemical characteristics of the
obtained concentrate such as color, viscosity, percentage of reduction
sugar, acidity and the microbial tests (mould and yeast) were
counted. The analysis was performed on the basis of factorial in the
form of completely randomized design (CRD) and Duncan's multiple
range test (DMRT) was used for the comparison of the means.
Statistical analysis of results showed that optimal conditions for
production of concentrate is round raisins when the solvent ratio was
2:1 with extraction temperature of 60°C and then concentration
temperature of 50°C. Round raisin is cheaper than the long one, and
it is more economical to concentrate production. Furthermore, round
raisin has more aromas and the less color degree with increasing the
temperature of concentration and extraction. Finally, according to
mentioned factors the concentrate of round raisin is recommended.
Abstract: Conventional materials like glass, wood or metals
replacement with polymer materials is still continuing. More simple
thus cheaper production is the main reason. However due to high
energy and petrochemical prices are polymer prices increasing too.
That´s why various kinds of fillers are used to make polymers
cheaper. Of course target is to maintain or improve properties of
these compounds. In this paper are solved rheology issues of
polymers compounded with vegetal origin fibers.
Abstract: A green design for assembly model is presented to
integrate design evaluation and assembly and disassembly sequence
planning by evaluating the three activities in one integrated model. For
an assembled product, an assembly sequence planning model is
required for assembling the product at the start of the product life cycle.
A disassembly sequence planning model is needed for disassembling
the product at the end. In a green product life cycle, it is important to
plan how a product can be disassembled, reused, or recycled, before
the product is actually assembled and produced. Given a product
requirement, there may be several design alternative cases to design
the same product. In the different design cases, the assembly and
disassembly sequences for producing the product can be different. In
this research, a new model is presented to concurrently evaluate the
design and plan the assembly and disassembly sequences. First, the
components are represented by using graph based models. Next, a
particle swarm optimization (PSO) method with a new encoding
scheme is developed. In the new PSO encoding scheme, a particle is
represented by a position matrix defining an assembly sequence and a
disassembly sequence. The assembly and disassembly sequences can
be simultaneously planned with an objective of minimizing the total of
assembly costs and disassembly costs. The test results show that the
presented method is feasible and efficient for solving the integrated
design evaluation and assembly and disassembly sequence planning
problem. An example product is implemented and illustrated in this
paper.
Abstract: Yogurts are prepared by fermenting milk with bacterial cultures consisting of a mixture of Streptococcus ssp. thermophilus and Lactobacillus delbrueckii ssp. bulgaricus. The main aim of this investigation was to develop a majority goat yogurt, with the addition of sheep milk in order to have a final product with good physicochemical quality properties and sensorial attributes. Four types of yogurts were prepared presenting the following proportion of goat and sheep milk respectively: C100 – 100%; C80 – 80%/20%; C60 – 60%/40%; C50 – 50%/50%. The goat milk was from the Serrana Jarmelista breed and the sheep milk from the Serra da Estrela breed. The inclusion of sheep milk improved attractiveness to consumers, and it also improved the nutritional value of the product, mainly the fatty acid and mineral contents. The C50 yogurt was preferred by 28% of the panellists, followed by the C100 with 16% and the commercial cow yogurt was 40% of preferences.
Abstract: In this study, oxidative steam reforming of methanol (OSRM) over a Au/CeO2–Fe2O3 catalyst prepared by a depositionprecipitation (DP) method was studied to produce hydrogen in order to feed a Proton Exchange Membrane Fuel Cell (PEMFC). The support (CeO2, Fe2O3, and CeO2–Fe2O3) were prepared by precipitation and co-precipitation methods. The impact of the support composition on the catalytic performance was studied by varying the Ce/(Ce+Fe) atomic ratio, it was found that the 1%Au/CF(0.25) calcined at 300 °C exhibited the highest catalytic activity in the whole temperature studied. In addition, the effect of Au content was investigated and 3%Au/CF(0.25) exhibited the highest activity under the optimum condition in the temperature range of 200 °C to 400 °C. The catalysts were characterized by various techniques: XRD, TPR, XRF, and UV-vis.
Abstract: Reactive powder concretes (RPC) are characterized by
particle diameter not exceeding 600 μm and having very high
compressive and tensile strengths. This paper describes a new
generation of micro concrete, which has an initial, as well as a final,
high physicomechanical performance. To achieve this, we replaced
the Portland cement (15% by weight) by materials rich in Silica (Slag
and Dune Sand).
The results obtained from tests carried out on RPC show that
compressive and tensile strengths increase when adding the additions,
thus improving the compactness of mixtures via filler and pozzolanic
effect.
With a reduction of the aggregate phase in the RPC and the
abundance of dune sand (south Algeria) and slag (industrial byproduct
of blast furnace), the use of the RPC will allow Algeria to
fulfil economical as well as ecological requirements.