Abstract: The aim of this investigation is to elaborate nearinfrared
methods for testing and recognition of chemical components
and quality in “Pannon wheat” allied (i.e. true to variety or variety
identified) milling fractions as well as to develop spectroscopic
methods following the milling processes and evaluate the stability of
the milling technology by different types of milling products and
according to sampling times, respectively. These wheat categories
produced under industrial conditions where samples were collected
versus sampling time and maximum or minimum yields. The changes
of the main chemical components (such as starch, protein, lipid) and
physical properties of fractions (particle size) were analysed by
dispersive spectrophotometers using visible (VIS) and near-infrared
(NIR) regions of the electromagnetic radiation. Close correlation
were obtained between the data of spectroscopic measurement
techniques processed by various chemometric methods (e.g. principal
component analysis [PCA], cluster analysis [CA]) and operation
condition of milling technology. It is obvious that NIR methods are
able to detect the deviation of the yield parameters and differences of
the sampling times by a wide variety of fractions, respectively. NIR
technology can be used in the sensitive monitoring of milling
technology.
Abstract: In this study, the experiments were carried out to
determine the best coolant for the quenching process among waterbased
silica, alumina, titania and copper oxide nanofluids (0.1 vol%).
A sphere made up off brass material was used in the experiments.
When the spherical test specimen was heated at high temperatures, it
was suddenly immersed into the nanofluids. All experiments were
carried out at saturated conditions and under atmospheric pressure.
After the experiments, the cooling curves were obtained by using the
temperature-time data of the specimen. The experimental results
showed that the cooling performance of test specimen depended on
the type of nanofluids. The silica nanoparticles enhanced the
performance of boiling heat transfer and it is the best coolant for the
quenching among other nanoparticles.
Abstract: Any signal transmitted over a channel is corrupted by noise and interference. A host of channel coding techniques has been proposed to alleviate the effect of such noise and interference. Among these Turbo codes are recommended, because of increased capacity at higher transmission rates and superior performance over convolutional codes. The multimedia elements which are associated with ample amount of data are best protected by Turbo codes. Turbo decoder employs Maximum A-posteriori Probability (MAP) and Soft Output Viterbi Decoding (SOVA) algorithms. Conventional Turbo coded systems employ Equal Error Protection (EEP) in which the protection of all the data in an information message is uniform. Some applications involve Unequal Error Protection (UEP) in which the level of protection is higher for important information bits than that of other bits. In this work, enhancement to the traditional Log MAP decoding algorithm is being done by using optimized scaling factors for both the decoders. The error correcting performance in presence of UEP in Additive White Gaussian Noise channel (AWGN) and Rayleigh fading are analyzed for the transmission of image with Discrete Cosine Transform (DCT) as source coding technique. This paper compares the performance of log MAP, Modified log MAP (MlogMAP) and Enhanced log MAP (ElogMAP) algorithms used for image transmission. The MlogMAP algorithm is found to be best for lower Eb/N0 values but for higher Eb/N0 ElogMAP performs better with optimized scaling factors. The performance comparison of AWGN with fading channel indicates the robustness of the proposed algorithm. According to the performance of three different message classes, class3 would be more protected than other two classes. From the performance analysis, it is observed that ElogMAP algorithm with UEP is best for transmission of an image compared to Log MAP and MlogMAP decoding algorithms.
Abstract: A sensory network consists of multiple detection
locations called sensor nodes, each of which is tiny, featherweight
and portable. A single path routing protocols in wireless sensor
network can lead to holes in the network, since only the nodes
present in the single path is used for the data transmission. Apart
from the advantages like reduced computation, complexity and
resource utilization, there are some drawbacks like throughput,
increased traffic load and delay in data delivery. Therefore, multipath
routing protocols are preferred for WSN. Distributing the traffic
among multiple paths increases the network lifetime. We propose a
scheme, for the data to be transmitted through a dominant path to
save energy. In order to obtain a high delivery ratio, a basic route
reconstruction protocol is utilized to reconstruct the path whenever a
failure is detected. A basic reconstruction routing (BRR) algorithm is
proposed, in which a node can leap over path failure by using the
already existing routing information from its neighbourhood while
the composed data is transmitted from the source to the sink. In order
to save the energy and attain high data delivery ratio, data is
transmitted along a multiple path, which is achieved by BRR
algorithm whenever a failure is detected. Further, the analysis of
how the proposed protocol overcomes the drawback of the existing
protocols is presented. The performance of our protocol is compared
to AOMDV and energy efficient node-disjoint multipath routing
protocol (EENDMRP). The system is implemented using NS-2.34.
The simulation results show that the proposed protocol has high
delivery ratio with low energy consumption.
Abstract: The main function of Medium Access Control (MAC) is to share the channel efficiently between all nodes. In the real-time scenario, there will be certain amount of wastage in bandwidth due to back-off periods. More bandwidth will be wasted in idle state if the back-off period is very high and collision may occur if the back-off period is small. So, an optimization is needed for this problem. The main objective of the work is to reduce delay due to back-off period thereby reducing collision and increasing throughput. Here a method, called the virtual back-off algorithm (VBA) is used to optimize the back-off period and thereby it increases throughput and reduces collisions. The main idea is to optimize the number of transmission for every node. A counter is introduced at each node to implement this idea. Here counter value represents the sequence number. VBA is classified into two types VBA with counter sharing (VBA-CS) and VBA with no counter sharing (VBA-NCS). These two classifications of VBA are compared for various parameters. Simulation is done in NS-2 environment. The results obtained are found to be promising.
Abstract: In order to determine the impact of thermo priming on germination of soybean seeds, an experiment was conducted as a completely randomized design with three replications. The factors of studied included different time thermo priming (control, 5 and 10 minutes) through the placing seeds were exposed to oven. The results showed that the effect of thermo priming was significant on germination percentage, seedling dry weight and seedling vigour in P ≤ 0.05. Mean comparison showed that the highest germination percentage (77%), seedling dry weight (1.39 g) and seedling vigour (107.03) were achieved by 10 minutes thermo priming.
Abstract: Stress of slaughter animals starting long before until at the time of process of slaughtering which cause misery and decrease of meat quality. Meanwhile, determination of animal stress using hormonal such as cortisol is expensive and less practical so that portable stress indicator for cows based on Fourier Transform Infrared Spectroscopy (FTIR) must be provided. The aims of this research are to find out the comparison process of slaughter between Rope Casting Local (RCL) and Restraining Box Method (RBM) by measuring of cortisol and wavelength in FTIR methods. Thirty two of male Ongole crossbred cattle were used in this experiment. Blood sampling was taken from jugular vein when they were rested and repeated when slaughtered. All of blood samples were centrifuged at 3000 rpm for 20 minutes to get serum, and then divided into two parts for cortisol assayed using ELISA and for measuring the wavelength using FTIR. The serum then measured at the wavelength between 4000-400 cm-1 using MB3000 FTIR. Band data absorption in wavelength of FTIR is analyzed descriptively by using FTIR Horizon MBTM. For RCL, average of serum cortisol when the animals rested were 11.47 ± 4.88 ng/mL, when the time of slaughter were 23.27 ± 7.84 ng/mL. For RBM, level of cortisol when rested animals were 13.67 ± 3.41 ng/mL and 53.47 ± 20.25 ng/mL during the slaughter. Based on student t-Test, there were significantly different between RBM and RCL methods when beef cattle were slaughtered (P0.05). Result of FTIR with the various of wavelength such as methyl group (=CH3 ) 2986cm-1, methylene (=CH2 ) 2827 cm-1, hydroxyl (- OH) 3371 cm-1, carbonyl (ketones) (C=O) 1636 cm-1, carboxyl (COO-1) 1408 cm-1, glucosa 1057 cm-1, urea 1011 cm-1have been obtained. It can be concluded that the RCL slaughtered method is better than the RBM method based on the increase of cortisol as an indicator of stress in beef cattle (P
Abstract: Surf is an increasingly popular sport and its performance evaluation is often qualitative. This work aims at using a smartphone to collect and analyze the GPS and inertial sensors data in order to obtain quantitative metrics of the surfing performance. Two approaches are compared for detection of wave rides, computing the number of waves rode in a surfing session, the starting time of each wave and its duration. The first approach is based on computing the velocity from the Global Positioning System (GPS) signal and finding the velocity thresholds that allow identifying the start and end of each wave ride. The second approach adds information from the Inertial Measurement Unit (IMU) of the smartphone, to the velocity thresholds obtained from the GPS unit, to determine the start and end of each wave ride. The two methods were evaluated using GPS and IMU data from two surfing sessions and validated with similar metrics extracted from video data collected from the beach. The second method, combining GPS and IMU data, was found to be more accurate in determining the number of waves, start time and duration. This paper shows that it is feasible to use smartphones for quantification of performance metrics during surfing. In particular, detection of the waves rode and their duration can be accurately determined using the smartphone GPS and IMU.
Abstract: To explore how the brain may recognise objects in its
general,accurate and energy-efficient manner, this paper proposes the
use of a neuromorphic hardware system formed from a Dynamic
Video Sensor (DVS) silicon retina in concert with the SpiNNaker
real-time Spiking Neural Network (SNN) simulator. As a first step
in the exploration on this platform a recognition system for dynamic
hand postures is developed, enabling the study of the methods used
in the visual pathways of the brain. Inspired by the behaviours of
the primary visual cortex, Convolutional Neural Networks (CNNs)
are modelled using both linear perceptrons and spiking Leaky
Integrate-and-Fire (LIF) neurons.
In this study’s largest configuration using these approaches, a
network of 74,210 neurons and 15,216,512 synapses is created and
operated in real-time using 290 SpiNNaker processor cores in parallel
and with 93.0% accuracy. A smaller network using only 1/10th of the
resources is also created, again operating in real-time, and it is able
to recognise the postures with an accuracy of around 86.4% - only
6.6% lower than the much larger system. The recognition rate of the
smaller network developed on this neuromorphic system is sufficient
for a successful hand posture recognition system, and demonstrates
a much improved cost to performance trade-off in its approach.
Abstract: Hybrid electric vehicles can reduce pollution and
improve fuel economy. Power-split hybrid electric vehicles (HEVs)
provide two power paths between the internal combustion engine
(ICE) and energy storage system (ESS) through the gears of an
electrically variable transmission (EVT). EVT allows ICE to operate
independently from vehicle speed all the time. Therefore, the ICE can
operate in the efficient region of its characteristic brake specific fuel
consumption (BSFC) map. The two-mode powertrain can operate in
input-split or compound-split EVT modes and in four different fixed
gear configurations. Power-split architecture is advantageous because
it combines conventional series and parallel power paths. This
research focuses on input-split and compound-split modes in the
two-mode power-split powertrain. Fuzzy Logic Control (FLC) for an
internal combustion engine (ICE) and PI control for electric machines
(EMs) are derived for the urban driving cycle simulation. These
control algorithms reduce vehicle fuel consumption and improve ICE
efficiency while maintaining the state of charge (SOC) of the energy
storage system in an efficient range.
Abstract: The paper develops a Non-Linear Model Predictive
Control (NMPC) of water quality in Drinking Water Distribution
Systems (DWDS) based on the advanced non-linear quality dynamics
model including disinfections by-products (DBPs). A special attention
is paid to the analysis of an impact of the flow trajectories prescribed
by an upper control level of the recently developed two-time scale
architecture of an integrated quality and quantity control in DWDS.
The new quality controller is to operate within this architecture in the
fast time scale as the lower level quality controller. The controller
performance is validated by a comprehensive simulation study based
on an example case study DWDS.
Abstract: Copper (I) oxide microparticles with the morphology
of cubic and hollow sphere were synthesized with the assistance of
surfactant as the shape controller. Both particles were then subjected
to study the catalytic activity and observed the results of shape effects
of catalysts on rate of catalytic reaction. The decolorizing reaction of
crystal violet and sodium hydroxide was chosen and measured the
decreasing of reactant with respect to times using spectrophotometer.
The result revealed that morphology of crystal had no effect on the
catalytic activity for crystal violet reaction but contributed to total
surface area predominantly.
Abstract: In this study, the pedestrian simulation VISWALK
integration and application platform ant algorithms written program
made to construct a renovation engineering schedule planning mode.
The use of simulation analysis platform construction site when the user
running the simulation, after calculating the user walks in the case of
construction delays, the ant algorithm to find out the minimum delay
time schedule plan, and add volume and unit area deactivated loss of
business computing, and finally to the owners and users of two
different positions cut considerations pick out the best schedule
planning. To assess and validate its effectiveness, this study
constructed the model imported floor of a shopping mall floor
renovation engineering cases. Verify that the case can be found from
the mode of the proposed project schedule planning program can
effectively reduce the delay time and the user's walking mall loss of
business, the impact of the operation on the renovation engineering
facilities in the building to a minimum.
Abstract: Aluminium matrix composites with alumina
reinforcements give superior mechanical & physical properties. Their
applications in several fields like automobile, aerospace, defense,
sports, electronics, bio-medical and other industrial purposes are
becoming essential for the last several decades. In the present work,
fabrication of hybrid composite was done by Stir casting technique
using Al 6061 as a matrix with alumina and silicon carbide (SiC) as
reinforcement materials. The weight percentage of alumina is varied
from 2 to 4% and the silicon carbide weight percentage is maintained
constant at 2%. Hardness and wear tests are performed in the as cast
and heat treated conditions. Age hardening treatment was performed
on the specimen with solutionizing at 550°C, aging at two
temperatures (150 and 200°C) for different time durations. Hardness
distribution curves are drawn and peak hardness values are recorded.
Hardness increase was very sensitive with respect to the decrease in
aging temperature. There was an improvement in wear resistance of
the peak aged material when aged at lower temperature. Also
increase in weight percent of alumina, increases wear resistance at
lower temperature but opposite behavior was seen when aged at
higher temperature.
Abstract: This paper addresses a cutting edge method of
business demand forecasting, based on an empirical probability
function when the historical behavior of the data is random.
Additionally, it presents error determination based on the numerical
method technique ‘propagation of errors.’ The methodology was
conducted characterization and process diagnostics demand planning
as part of the production management, then new ways to predict its
value through techniques of probability and to calculate their mistake
investigated, it was tools used numerical methods. All this based on
the behavior of the data. This analysis was determined considering
the specific business circumstances of a company in the sector of
communications, located in the city of Bogota, Colombia. In
conclusion, using this application it was possible to obtain the
adequate stock of the products required by the company to provide its
services, helping the company reduce its service time, increase the
client satisfaction rate, reduce stock which has not been in rotation
for a long time, code its inventory, and plan reorder points for the
replenishment of stock.
Abstract: This study examines the feasibility of indirect solar
desalination in oil producing countries in the Middle East and North
Africa (MENA) region. It relies on value engineering (VE) and costbenefit
with sensitivity analyses to identify optimal coupling
configurations of desalination and solar energy technologies. A
comparative return on investment was assessed as a function of water
costs for varied plant capacities (25,000 to 75,000 m3/day), project
lifetimes (15 to 25 years), and discount rates (5 to 15%) taking into
consideration water and energy subsidies, land cost as well as
environmental externalities in the form of carbon credit related to
greenhouse gas (GHG) emissions reduction. The results showed
reverse osmosis (RO) coupled with photovoltaic technologies (PVs)
as the most promising configuration, robust across different prices for
Brent oil, discount rates, as well as different project lifetimes.
Environmental externalities and subsidies analysis revealed that a
16% reduction in existing subsidy on water tariffs would ensure
economic viability. Additionally, while land costs affect investment
attractiveness, the viability of RO coupled with PV remains possible
for a land purchase cost
Abstract: The Economic Lot Scheduling Problem (ELSP) is a
valuable mathematical model that can support decision-makers to
make scheduling decisions. The basic period approach is effective for
solving the ELSP. The assumption for applying the basic period
approach is that a product must use its maximum production rate to be
produced. However, a product can lower its production rate to reduce
the average total cost when a facility has extra idle time. The past
researches discussed how a product adjusts its production rate under
the common cycle approach. To the best of our knowledge, no studies
have addressed how a product lowers its production rate under the
basic period approach. This research is the first paper to discuss this
topic. The research develops a simple fixed rate approach that adjusts
the production rate of a product under the basic period approach to
solve the ELSP. Our numerical example shows our approach can find a
better solution than the traditional basic period approach. Our
mathematical model that applies the fixed rate approach under the
basic period approach can serve as a reference for other related
researches.
Abstract: The system for analyzing and eliciting public
grievances serves its main purpose to receive and process all sorts of
complaints from the public and respond to users. Due to the more
number of complaint data becomes big data which is difficult to store
and process. The proposed system uses HDFS to store the big data
and uses MapReduce to process the big data. The concept of cache
was applied in the system to provide immediate response and timely
action using big data analytics. Cache enabled big data increases the
response time of the system. The unstructured data provided by the
users are efficiently handled through map reduce algorithm. The
processing of complaints takes place in the order of the hierarchy of
the authority. The drawbacks of the traditional database system used
in the existing system are set forth by our system by using Cache
enabled Hadoop Distributed File System. MapReduce framework
codes have the possible to leak the sensitive data through
computation process. We propose a system that add noise to the
output of the reduce phase to avoid signaling the presence of
sensitive data. If the complaints are not processed in the ample time,
then automatically it is forwarded to the higher authority. Hence it
ensures assurance in processing. A copy of the filed complaint is sent
as a digitally signed PDF document to the user mail id which serves
as a proof. The system report serves to be an essential data while
making important decisions based on legislation.
Abstract: To mitigate the urban heat island effect has become a
global issue when we are faced with the challenge of climate change.
Through literature review, plant photosynthesis can reduce the carbon
dioxide and mitigate the urban heat island effect to a degree. Because
there are not enough open space and parks, green roof has become an
important policy in Taiwan.
We selected elementary school buildings in northern New Taipei
City as research subjects since elementary schools are asked with
priority to build green roof and important educational place to promote
green roof concept. Testo175-H1 recording device was used to record
the temperature and humidity differences between roof surface and
interior space below roof with and without green roof in the long-term.
We also use questionnaires to investigate the awareness of comfort
level of green roof and sensation of teachers and students of the
elementary schools.
The results indicated that the temperature of roof without greening
was higher than that with greening by about 2°C. But sometimes
during noontime, the temperature of green roof was higher than that of
non-green roof probably because of the character of the accumulation
and dissipation of heat of greening. The temperature of the interior
space below green roof was normally lower than that without green
roof by about 1°C, showing that green roof could lower the
temperature. The humidity of the green roof was higher than the one
without greening also indicated that green roof retained water better.
Teachers liked to combine green roof concept in the curriculum,
and students wished all classes can take turns to maintain the green
roof. Teachers and students whose school had integrated green roof
concept in the curriculum were more willing to participate in the
maintenance work of green roof. Teachers and students who may have
access to and touch the green roof can be more aware of the green roof
benefit. We suggest architects to increase the accessibility and
visibility of green roof, such as use it as a part of the activity space.
This idea can be a reference to the green roof curriculum design.
Abstract: The objective of this paper is to present the process of
change in management accounting in Romania, a former communist
country from Eastern Europe. In order to explain this process, we used
the contingency and institutional theories. We focused on the
following directions: the presentation of the scientific context and
motivation of this research and the case study. We presented the state
of the art in the process of change in the management accounting from
the international and national perspective. We also described the
evolution of management accounting in Romania in the context of
economic and political changes. An important moment was the fall of
communism in 1989. This represents a starting point for a new
economic environment and for new management accounting.
Accordingly, we developed a case study which presented this
evolution. The conclusion of our research was that the changes in the
management accounting system of the company analysed occurred in
the same time with the institutionalisation of some elements (e.g.
degree of competition, training and competencies in management
accounting). The management accounting system was modelled by the
contingencies specific to this company (e.g. environment, industry,
strategy).