Abstract: In this paper, we focus on the problem of driving and
herding a collection of autonomous actors to a given area. Then, a
new method based on multi-agent coordination is proposed for
solving the problem.
In our proposed method, we assume that the environment is
covered by sensors. When an event is occurred, sensors forward
information to a sink node. Based on received information, the sink
node will estimate the direction and the speed of movement of actors
and announce the obtained value to the actors. The actors coordinate
to reach the target location.
Abstract: Solar water heating (SWH) systems are gaining popularity in ASEAN in the midst of increasing number of affluent population in society and environmental concerns from seemingly unchanged reliance on fossil-based fuels. The penetration of these systems and technologies into ASEAN markets is a welcome development; however there is a need for the method of assessment of their thermal performances. This paper discusses the reasons for this need and a suitable method for thermal performance evaluation of SWH systems in ASEAN. The paper also calls on research to be focused on the establishment of reliable data to be entered into the performance rating software. The establishment of accredited solar systems testing facilities can help boost the competitiveness of ASEAN solar industry.
Abstract: In this paper, a clustering algorithm named KHarmonic
means (KHM) was employed in the training of Radial
Basis Function Networks (RBFNs). KHM organized the data in
clusters and determined the centres of the basis function. The popular
clustering algorithms, namely K-means (KM) and Fuzzy c-means
(FCM), are highly dependent on the initial identification of elements
that represent the cluster well. In KHM, the problem can be avoided.
This leads to improvement in the classification performance when
compared to other clustering algorithms. A comparison of the
classification accuracy was performed between KM, FCM and KHM.
The classification performance is based on the benchmark data sets:
Iris Plant, Diabetes and Breast Cancer. RBFN training with the KHM
algorithm shows better accuracy in classification problem.
Abstract: We consider the development of an eight order Adam-s
type method, with A-stability property discussed by expressing them
as a one-step method in higher dimension. This makes it suitable
for solving variety of initial-value problems. The main method and
additional methods are obtained from the same continuous scheme
derived via interpolation and collocation procedures. The methods
are then applied in block form as simultaneous numerical integrators
over non-overlapping intervals. Numerical results obtained using the
proposed block form reveals that it is highly competitive with existing
methods in the literature.
Abstract: This paper focuses on the 3D reconstruction of
the architectural design of Darul Ridzuan Museum. It has
concentrated on designing exterior part of the building according
to colored digital photo of the real museum. Besides viewing the
architecture, walkthroughs are generated for the user to control
it in an easier way. User can travel through the museum to get
the feel of the environment and to explore the design of the
museum as a whole; both exterior and interior. The result has
shown positive result in terms of realism, navigation, collision
detection, suitability, usability and user-s acceptance. In brief,
the 3D virtual museum has provided an alternative to present a
real museum.
Abstract: There has been a growing interest in the field of
bio-mimetic robots that resemble the shape of an insect or an aquatic
animal, among many others. One bio-mimetic robot serves the
purpose of exploring pipelines, spotting any troubled areas or
malfunctions and reporting its data. Moreover, the robot is able to
prepare for and react to any abnormal routes in the pipeline. In order
to move effectively inside a pipeline, the robot-s movement will
resemble that of a lizard. When situated in massive pipelines with
complex routes, the robot places fixed sensors in several important
spots in order to complete its monitoring. This monitoring task is to
prevent a major system failure by preemptively recognizing any minor
or partial malfunctions. Areas uncovered by fixed sensors are usually
impossible to provide real-time observation and examination, and thus
are dependant on periodical offline monitoring. This paper provides
the Monitoring System that is able to monitor the entire area of
pipelines–with and without fixed sensors–by using the bio-mimetic
robot.
Abstract: Application of wood in rural construction is diffused
all around the world since remote times. However, its inclusion in
structural design deserves strong support from broad knowledge of
material properties. The pertinent literature reveals the application of
optical methods in determining the complete field displacement on
bodies exhibiting regular as well as irregular surfaces. The use of
moiré techniques in experimental mechanics consists in analyzing the
patterns generated on the body surface before and after deformation.
The objective of this research work is to study the qualitative
deformation behavior of wooden testing specimens under specific
loading situations. The experiment setup follows the literature
description of shadow moiré methods. Results indicate strong
anisotropy influence of the generated displacement field. Important
qualitative as well as quantitative stress and strain distribution were
obtained wooden members which are applicable to rural
constructions.
Abstract: The spin (ms) and orbital (mo) magnetic moment of
the antiferromagnetic NiO and MnO have been studied in the local
spin density approximation (LSDA+U) within full potential linear
muffin-tin orbital (FP-LMTO method with in the coulomb interaction
U varying from 0 to 10eV, exchange interaction J, from 0 to 1.0eV,
and volume compression VC in range of 0 to 80%. Our calculated
results shown that the spin magnetic moments and the orbital
magnetic moments increase linearly with increasing U and J. While
the interesting behaviour appears when volume compression is
greater than 70% for NiO and 50% for MnO at which ms collapses.
Further increase of volume compression to be at 80% leads to the
disappearance of both magnetic moments.
Abstract: De novo genome assembly is always fragmented. Assembly fragmentation is more serious using the popular next generation sequencing (NGS) data because NGS sequences are shorter than the traditional Sanger sequences. As the data throughput of NGS is high, the fragmentations in assemblies are usually not the result of missing data. On the contrary, the assembled sequences, called contigs, are often connected to more than one other contigs in a complicated manner, leading to the fragmentations. False connections in such complicated connections between contigs, named a contig graph, are inevitable because of repeats and sequencing/assembly errors. Simplifying a contig graph by removing false connections directly improves genome assembly. In this work, we have developed a tool, SIMGraph, to resolve ambiguous connections between contigs using NGS data. Applying SIMGraph to the assembly of a fungus and a fish genome, we resolved 27.6% and 60.3% ambiguous contig connections, respectively. These results can reduce the experimental efforts in resolving contig connections.
Abstract: Construction of tunnels is connected with high
uncertainty in the field of costs, construction period, safety and
impact on surroundings. Risk management became therefore a
common part of tunnel projects, especially after a set of fatal
collapses occurred in 1990's. Such collapses are caused usually by
combination of factors that can be divided into three main groups, i.e.
unfavourable geological conditions, failures in the design and
planning or failures in the execution.
This paper suggests a procedure enabling quantification of the
excavation risk related to extraordinary accidents using FTA and
ETA tools. It will elaborate on a common process of risk analysis and
enable the transfer of information and experience between particular
tunnel construction projects. Further, it gives a guide for designers,
management and other participants, how to deal with risk of such
accidents and how to make qualified decisions based on a
probabilistic approach.
Abstract: This paper presents a semi-supervised learning algorithm called Iterative-Cross Training (ICT) to solve the Web pages classification problems. We apply Inductive logic programming (ILP) as a strong learner in ICT. The objective of this research is to evaluate the potential of the strong learner in order to boost the performance of the weak learner of ICT. We compare the result with the supervised Naive Bayes, which is the well-known algorithm for the text classification problem. The performance of our learning algorithm is also compare with other semi-supervised learning algorithms which are Co-Training and EM. The experimental results show that ICT algorithm outperforms those algorithms and the performance of the weak learner can be enhanced by ILP system.
Abstract: In this work, we experimentally study heat transfer
from exhaust particulate air of detergent spray drying tower to water
by using coiled tube heat exchanger. Water flows in the coiled
tubes, where air loaded with detergent particles of 43 micrometers
in diameter flows within the shell. Four coiled tubes with different
coil pitches are used in a counter-current flow configuration. We
investigate heat transfer coefficients of inside and outside the heat
transfer surfaces through 400 experiments. The correlations between
Nusselt number and Reynolds number, Prandtl number, mass flow
rate of particulates to mass flow rate of air ratio and coiled tube
pitch parameter are proposed. The correlations procured can be used
to predicted heat transfer between tube and shell of the heat
exchanger.
Abstract: Rapid enlargement and physical development of cities
have facilitated the emergence of a number of city life crises and
decrease of environment quality. Subsequently, the need for noticing
the concept of quality and its improvement in urban environments,
besides quantitative issues, is obviously recognized. In the domain of
urban ideas the importance of taking these issues into consideration
is obvious not only in accordance to sustainable development
concepts and improvement of public environment quality, but also in
the enhancement of social and behavioral models.
The major concern of present article is to study the nature of urban
environment quality in urban development plans, which is important
not only in the concept and the aim of projects but also in their
execution procedure. As a result, this paper is going to utilize
planning capacities caused by environmental virtues in the planning
procedure of Moft Abad neighborhood. Thus, at the first step,
applying the Analytical Hierarchy Process (AHP), it has assessed
quantitative environmental issues. The present conditions of Moft
Abad state that “the neighborhood is generally suffering from the
lack of qualitative parameters, and the previously formed planning
procedures could not take the sustainable and developmental paths
which are aimed at environment quality virtues." The diminution of
economical and environmental virtues has resulted in the diminution
of residential and social virtues. Therefore, in order to enhance the
environment quality in Moft Abad, the present paper has tried to
supply the subject plans in order to make a safe, healthy, and lively
neighborhood.
Abstract: Phase locked loops for data links operating at 10 Gb/s
or faster are low phase noise devices designed to operate with a low
jitter reference clock. Characterization of their jitter transfer function
is difficult because the intrinsic noise of the device is comparable to
the random noise level in the reference clock signal. A linear model
is proposed to account for the intrinsic noise of a PLL. The intrinsic
noise data of a PLL for 10 Gb/s links is presented. The jitter transfer
function of a PLL in a test chip for 12.8 Gb/s data links was
determined in experiments using the 400 MHz reference clock as the
source of simultaneous excitations over a wide range of frequency.
The result shows that the PLL jitter transfer function can be
approximated by a second order linear model.
Abstract: Geographic Information System (GIS) is a computerbased
tool used extensively to solve various engineering problems
related to spatial data. In spite of growing popularity of GIS, its
complete potential to construction industry has not been realized. In
this paper, the summary of up-to-date work on spatial applications of
GIS technologies in construction industry is presented. GIS
technologies have the potential to solve space related problems of
construction industry involving complex visualization, integration of
information, route planning, E-commerce, cost estimation, etc. GISbased
methodology to handle time and space issues of construction
projects scheduling is developed and discussed in this paper.
Abstract: With the advantage of wireless network technology,
there are a variety of mobile applications which make the issue of
wireless sensor networks as a popular research area in recent years.
As the wireless sensor network nodes move arbitrarily with the
topology fast change feature, mobile nodes are often confronted with
the void issue which will initiate packet losing, retransmitting,
rerouting, additional transmission cost and power consumption.
When transmitting packets, we would not predict void problem
occurring in advance. Thus, how to improve geographic routing with
void avoidance in wireless networks becomes an important issue. In
this paper, we proposed a greedy geographical void routing algorithm
to solve the void problem for wireless sensor networks. We use the
information of source node and void area to draw two tangents to
form a fan range of the existence void which can announce voidavoiding
message. Then we use source and destination nodes to draw
a line with an angle of the fan range to select the next forwarding
neighbor node for routing. In a dynamic wireless sensor network
environment, the proposed greedy void avoiding algorithm can be
more time-saving and more efficient to forward packets, and improve
current geographical void problem of wireless sensor networks.
Abstract: In the traditional theory of non-uniform torsion the
axial displacement field is expressed as the product of the unit twist
angle and the warping function. The first one, variable along the
beam axis, is obtained by a global congruence condition; the second
one, instead, defined over the cross-section, is determined by solving
a Neumann problem associated to the Laplace equation, as well as for
the uniform torsion problem.
So, as in the classical theory the warping function doesn-t punctually
satisfy the first indefinite equilibrium equation, the principal aim of
this work is to develop a new theory for non-uniform torsion of
beams with axial symmetric cross-section, fully restrained on both
ends and loaded by a constant torque, that permits to punctually
satisfy the previous equation, by means of a trigonometric expansion
of the axial displacement and unit twist angle functions.
Furthermore, as the classical theory is generally applied with good
results to the global and local analysis of ship structures, two beams
having the first one an open profile, the second one a closed section,
have been analyzed, in order to compare the two theories.
Abstract: In the past years a lot of effort has been made in the
field of face detection. The human face contains important features
that can be used by vision-based automated systems in order to
identify and recognize individuals. Face location, the primary step of
the vision-based automated systems, finds the face area in the input
image. An accurate location of the face is still a challenging task.
Viola-Jones framework has been widely used by researchers in order
to detect the location of faces and objects in a given image. Face
detection classifiers are shared by public communities, such as
OpenCV. An evaluation of these classifiers will help researchers to
choose the best classifier for their particular need. This work focuses
of the evaluation of face detection classifiers minding facial
landmarks.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: This paper undertakes the problem of optimal
capacitor placement in a distribution system. The problem is how to
optimally determine the locations to install capacitors, the types and
sizes of capacitors to he installed and, during each load level,the
control settings of these capacitors in order that a desired objective
function is minimized while the load constraints,network constraints
and operational constraints (e.g. voltage profile) at different load
levels are satisfied. The problem is formulated as a combinatorial
optimization problem with a nondifferentiable objective function.
Four solution mythologies based on algorithms (GA),tabu search
(TS), and hybrid GA-SA algorithms are presented.The solution
methodologies are preceded by a sensitivity analysis to select the
candidate capacitor installation locations.