Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: We propose a new perspective on speech
communication using blind source separation. The original speech is
mixed with key signals which consist of the mixing matrix, chaotic
signals and a random noise. However, parts of the keys (the mixing
matrix and the random noise) are not necessary in decryption. In
practice implement, one can encrypt the speech by changing the noise
signal every time. Hence, the present scheme obtains the advantages
of a One Time Pad encryption while avoiding its drawbacks in key
exchange. It is demonstrated that the proposed scheme is immune
against traditional attacks.
Abstract: The peel of dragon fruit is a byproduct left over after consuming. Normally, the use of plants as antioxidant source must be dried before further process. Therefore, the aim of this study is interesting to dry the peel by heat pump dryer (45 ºC) and fluidized bed dryer (110 º C) compared with the sun drying method. The sample with initial moisture content of about 85-91% wet basis was dried down to about 10% wet basis where it took 620 and 25 min for heat pump dryer and fluidized bed dryer, respectively. However, the sun drying took about 900 min to dry the peel. After that, sample was evaluated antioxidant activity, -carotene and betalains contents. The results found that the antioxidant activity and betalains contents of dried peel obtained from heat pump and fluidized bed dryings were significantly higher than that sun drying (p 0.05). Moreover, the drying by heat pump provided the highest -carotene content.
Abstract: Robust nonlinear integrated navigation of GPS and
low cost MEMS is a hot topic of research these days. A robust filter
is required to cope up with the problem of unpredictable
discontinuities and colored noises associated with low cost sensors.
H∞ filter is previously used in Extended Kalman filter and Unscented
Kalman filter frame. Unscented Kalman filter has a problem of
Cholesky matrix factorization at each step which is a very unstable
operation. To avoid this problem in this research H∞ filter is
designed in Square root Unscented filter framework and found 50%
more robust towards increased level of colored noises.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: It is important for an autonomous mobile robot to know
where it is in any time in an indoor environment. In this paper, we
design a relative self-localization algorithm. The algorithm compare
the interest point in two images and compute the relative displacement
and orientation to determent the posture. Firstly, we use the SURF
algorithm to extract the interest points of the ceiling. Second, in order
to reduce amount of calculation, a replacement SURF is used to extract
orientation and description of the interest points. At last, according to
the transformation of the interest points in two images, the relative
self-localization of the mobile robot will be estimated greatly.
Abstract: We present a novel scheme to recognize isolated speech
signals using certain statistical parameters derived from those signals.
The determination of the statistical estimates is based on extracted
signal information rather than the original signal information in
order to reduce the computational complexity. Subtle details of
these estimates, after extracting the speech signal from ambience
noise, are first exploited to segregate the polysyllabic words from
the monosyllabic ones. Precise recognition of each distinct word is
then carried out by analyzing the histogram, obtained from these
information.
Abstract: In this study, fuzzy rule-based classifier is used for the
diagnosis of congenital heart disease. Congenital heart diseases are
defined as structural or functional heart disease. Medical data sets
were obtained from Pediatric Cardiology Department at Selcuk
University, from years 2000 to 2003. Firstly, fuzzy rules were
generated by using medical data. Then the weights of fuzzy rules
were calculated. Two different reasoning methods as “weighted vote
method" and “singles winner method" were used in this study. The
results of fuzzy classifiers were compared.
Abstract: This work deals with the design of the robotic assembly
system for the roller clamps. The task is characterized by high speed,
high yield and safety engagement. This paper describes the design of
different parts of an automated high speed machine to assemble the
parts of roller clamps. The roller clamp robotic assembly system
performs various processes in the assembly line which include clamp
body and roller feeding, inserting the roller into the clamp body, and
dividing the rejected clamp and successfully assembled clamp into
their own tray. The electrical/electronics design of the machine is
discussed. The target is to design a cost effective, minimum
maintenance and high speed machine for the industry applications.
Abstract: Text Mining is an important step of Knowledge
Discovery process. It is used to extract hidden information from notstructured
o semi-structured data. This aspect is fundamental because
much of the Web information is semi-structured due to the nested
structure of HTML code, much of the Web information is linked,
much of the Web information is redundant. Web Text Mining helps
whole knowledge mining process to mining, extraction and
integration of useful data, information and knowledge from Web
page contents.
In this paper, we present a Web Text Mining process able to
discover knowledge in a distributed and heterogeneous multiorganization
environment. The Web Text Mining process is based on
flexible architecture and is implemented by four steps able to
examine web content and to extract useful hidden information
through mining techniques. Our Web Text Mining prototype starts
from the recovery of Web job offers in which, through a Text Mining
process, useful information for fast classification of the same are
drawn out, these information are, essentially, job offer place and
skills.
Abstract: In this study the elastic-plastic stress distribution in
weld-bonded joint, fabricated from austenitic stainless steel (AISI
304) sheet of 1.00 mm thickness and Epoxy adhesive Araldite 2011,
subjected to axial loading is investigated. This is needed to improve
design procedures and welding codes, and saving efforts in the
cumbersome experiments and analysis. Therefore, a complete 3-D
finite element modelling and analysis of spot welded, bonded and
weld-bonded joints under axial loading conditions is carried out. A
comprehensive systematic experimental program is conducted to
determine many properties and quantities, of the base metals and the
adhesive, needed for FE modelling, such like the elastic – plastic
properties, modulus of elasticity, fracture limit, the nugget and heat
affected zones (HAZ) properties, etc. Consequently, the finite
element models developed, for each case, are used to evaluate
stresses distributions across the entire joint, in both the elastic and
plastic regions. The stress distribution curves are obtained,
particularly in the elastic regions and found to be consistent and in
excellent agreement with the published data. Furthermore, the
stresses distributions are obtained in the weld-bonded joint and
display the best results with almost uniform smooth distribution
compared to spot and bonded cases. The stress concentration peaks at
the edges of the weld-bonded region, are almost eliminated resulting
in achieving the strongest joint of all processes.
Abstract: EcoDam is an adenine-N6 DNA methyltransferase
that methylates the GATC sites in the Escherichia coli genome.
DNA-adenine methylation is not present in higher eukaryotes
including humans. These observations raise the possibility that dam
inhibitors may be used as anti-microbial agents. Polyphosphate
(Poly(P)) is an important metabolite and signaling molecule in
prokaryotes and eukaryotes. Here, by using gel retardation
experiments to investigate the competition of DNA binding by
EcoDam in the presence of polyphosphate, we found that Poly (P)
strongly interferes with DNA binding by EcoDam, while same
concentration of monophosphate does not. In addition, we
demonstrated that Poly (P) binding inhibits the activity of EcoDam
and our results suggest that Poly (P) led to strong inhibition of the
EcoDam catalytic activity, while monophosphate had only moderate
effect.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: Evolvable hardware (EHW) refers to a selfreconfiguration
hardware design, where the configuration is under
the control of an evolutionary algorithm (EA). A lot of research has
been done in this area several different EA have been introduced.
Every time a specific EA is chosen for solving a particular problem,
all its components, such as population size, initialization, selection
mechanism, mutation rate, and genetic operators, should be selected
in order to achieve the best results. In the last three decade a lot of
research has been carried out in order to identify the best parameters
for the EA-s components for different “test-problems". However
different researchers propose different solutions. In this paper the
behaviour of mutation rate on (1+λ) evolution strategy (ES) for
designing logic circuits, which has not been done before, has been
deeply analyzed. The mutation rate for an EHW system modifies
values of the logic cell inputs, the cell type (for example from AND
to NOR) and the circuit output. The behaviour of the mutation has
been analyzed based on the number of generations, genotype
redundancy and number of logic gates used for the evolved circuits.
The experimental results found provide the behaviour of the mutation
rate to be used during evolution for the design and optimization of
logic circuits. The researches on the best mutation rate during the last
40 years are also summarized.
Abstract: This paper invites to dialogue and reflections on
innovation and entrepreneurship by presenting concepts of innovation
leading to the introduction of a complex theoretical framework;
Cooperative Innovation (CO-IN). CO-IN is a didactic model
enhancing and scaffolding processes of cooperation creating
innovation drawing on a Scandinavian tradition.
CO-IN is based on a cross-sectorial and multidisciplinary
approach. We introduce the concept of complementarity to help
capture the validity of diversity and we suggest the concept of “the
space in between" to understand the creation of identity as a
collective mind. We see dialogue and the use of multi modal
techniques as essential tools for conceptualizations giving possibility
for clarification of the complexity and diversity leading to decision
making based on knowledge as commons.
We introduce the didactic design and present our empirical
findings from an innovation workshop in Argentina. In a final
paragraph we reflect on the design as a support of the development of
common ground, collective mind and collective action and the
creation of knowledge as commons to facilitate innovation and
entrepreneurship.
Abstract: The overriding goal of software engineering is to
provide a high quality system, application or a product. To achieve
this goal, software engineers must apply effective methods coupled
with modern tools within the context of a mature software process
[2]. In addition, it is also must to assure that high quality is realized.
Although many quality measures can be collected at the project
levels, the important measures are errors and defects. Deriving a
quality measure for reusable components has proven to be
challenging task now a days. The results obtained from the study are
based on the empirical evidence of reuse practices, as emerged from
the analysis of industrial projects. Both large and small companies,
working in a variety of business domains, and using object-oriented
and procedural development approaches contributed towards this
study. This paper proposes a quality metric that provides benefit at
both project and process level, namely defect removal efficiency
(DRE).
Abstract: In order to survive in a rapidly changing business environment, Malaysian business firms must improve their own business practices and procedures. This paper describes the impact of Critical Success Factors (CSFs) during the Enterprise Resource Planning (ERP) system implementations using the responses from 151 organizations that completed or are in the process of completing an ERP implementation and identifying the key benefits of ERP implementation in the firm. The importance of these factors was investigated within Malaysian companies using questionnaire survey method. Our results provide advice to management on how best to utilize their limited resources to choose those CSFs that are most likely to have an impact upon the implementation of the ERP system.
Abstract: A model of (4, 4) single-walled boron-nitride nanotube as a representative of armchair boron-nitride nanotubes studied. At first the structure optimization performed and then Nuclear Magnetic Resonance parameters (NMR) by Density Functional Theory (DFT) method at 11B and 15N nuclei calculated. Resulted parameters evaluation presents electrostatic environment heterogeneity along the nanotube and especially at the ends but the nuclei in a layer feel the same electrostatic environment. All of calculations carried out using Gaussian 98 Software package.
Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: In this paper, the implementation of low power,
high throughput convolutional filters for the one dimensional
Discrete Wavelet Transform and its inverse are presented. The
analysis filters have already been used for the implementation of a
high performance DWT encoder [15] with minimum memory
requirements for the JPEG 2000 standard. This paper presents the
design techniques and the implementation of the convolutional filters
included in the JPEG2000 standard for the forward and inverse DWT
for achieving low-power operation, high performance and reduced
memory accesses. Moreover, they have the ability of performing
progressive computations so as to minimize the buffering between
the decomposition and reconstruction phases. The experimental
results illustrate the filters- low power high throughput characteristics
as well as their memory efficient operation.