Abstract: A design of communication area for infrared
electronic-toll-collection systems to provide an extended
communication interval in the vehicle traveling direction and
regular boundary between contiguous traffic lanes is proposed.
By utilizing two typical low-cost commercial infrared LEDs with
different half-intensity angles Φ1/2 = 22◦ and 10◦, the radiation
pattern of the emitter is designed to properly adjust the spatial
distribution of the signal power. The aforementioned purpose
can be achieved with an LED array in a three-piece structure
with appropriate mounting angles. With this emitter, the influence
of the mounting parameters, including the mounting height and
mounting angles of the on-board unit and road-side unit, on the
system performance in terms of the received signal strength and
communication area are investigated. The results reveal that, for
our emitter proposed in this paper, the ideal ”long-and-narrow”
characteristic of the communication area is very little affected by
these mounting parameters. An optimum mounting configuration is
also suggested.
Abstract: In this paper, we provide complete end-to-end delay analyses including the relay nodes for instant messages. Message Session Relay Protocol (MSRP) is used to provide congestion control for large messages in the Instant Messaging (IM) service. Large messages are broken into several chunks. These chunks may traverse through a maximum number of two relay nodes before reaching destination according to the IETF specification of the MSRP relay extensions. We discuss the current solutions of sending large instant messages and introduce a proposal to reduce message flows in the IM service. We consider virtual traffic parameter i.e., the relay nodes are stateless non-blocking for scalability purpose. This type of relay node is also assumed to have input rate at constant bit rate. We provide a new scheduling policy that schedules chunks according to their previous node?s delivery time stamp tags. Validation and analysis is shown for such scheduling policy. The performance analysis with the model introduced in this paper is simple and straight forward, which lead to reduced message flows in the IM service.
Abstract: This paper presents a method for determining the
uniaxial tensile properties such as Young-s modulus, yield strength
and the flow behaviour of a material in a virtually non-destructive
manner. To achieve this, a new dumb-bell shaped miniature
specimen has been designed. This helps in avoiding the removal of
large size material samples from the in-service component for the
evaluation of current material properties. The proposed miniature
specimen has an advantage in finite element modelling with respect
to computational time and memory space. Test fixtures have been
developed to enable the tension tests on the miniature specimen in a
testing machine. The studies have been conducted in a chromium
(H11) steel and an aluminum alloy (AR66). The output from the
miniature test viz. load-elongation diagram is obtained and the finite
element simulation of the test is carried out using a 2D plane stress
analysis. The results are compared with the experimental results. It is
observed that the results from the finite element simulation
corroborate well with the miniature test results. The approach seems
to have potential to predict the mechanical properties of the
materials, which could be used in remaining life estimation of the
various in-service structures.
Abstract: This paper explores the knowledge and attitude of
women and men in decision making on pap smear screening. This
qualitative study recruited 52 respondents with 44 women and 8 men,
using the purposive sampling with snowballing technique through indepth
interviews. This study demonstrates several key findings:
Female respondents have better knowledge compared to male. Most
of the women perceived that pap smear screening is beneficial and
important, but to proceed with the test is still doubtful. Male
respondents were supportive in terms of sending their spouses to the
health facilities or give more freedom to their wives to choose and
making decision on their own health due to prominent reason that
women know best on their own health. It is expected that the results
from this study will provide useful guideline for healthcare providers
to prepare any action/intervention to provide an extensive education
to improve people-s knowledge and attitude towards pap smear.
Abstract: The Portuguese Constitution, in article 22, instituted
the general principle of tort liability of the State and other public law
entities.
Consequently, ordinary legislation established the tort liability of
the State into the Portuguese Legal Order, by means of Decree-Law
48051, of 1967.
This decree, which was criticised extensively, was amended by
virtue of Law 67/2007, of 31st December, establishing the regime for
tort liability arising from losses caused by third parties, due to the
acts of public management in relation to all the functions of the State,
i.e. i) administrative, ii) legislative, and iii) jurisdictional.
Abstract: In this present study, experimental work was
conducted to study the effectiveness of newly innovated steel-CFRP
composite (CFRP laminates sandwiched between two steel strips) as
stirrups. A total numbers of eight concrete beams were tested under
four point loads. Each beam measured 1600 mm long, 160mm width
and 240 mm depth. The beams were reinforced with different shear
reinforcements; one without stirrups, one with steel stirrups and six
with different types and numbers of steel-CRFR stirrups. Test results
indicated that the steel-CFRP stirrups had enhanced the shear
strength capacity of beams. Moreover, the tests revealed that steel-
CFRP stirrups reached to their ultimate tensile strength unlike FRP
stirrups which rupture at much lower level than their ultimate
strength as werereported in various researches.
Abstract: In this paper we present a technique to speed up
ICA based on the idea of reducing the dimensionality of the data
set preserving the quality of the results. In particular we refer to
FastICA algorithm which uses the Kurtosis as statistical property
to be maximized. By performing a particular Johnson-Lindenstrauss
like projection of the data set, we find the minimum dimensionality
reduction rate ¤ü, defined as the ratio between the size k of the reduced
space and the original one d, which guarantees a narrow confidence
interval of such estimator with high confidence level. The derived
dimensionality reduction rate depends on a system control parameter
β easily computed a priori on the basis of the observations only.
Extensive simulations have been done on different sets of real world
signals. They show that actually the dimensionality reduction is very
high, it preserves the quality of the decomposition and impressively
speeds up FastICA. On the other hand, a set of signals, on which the
estimated reduction rate is greater than 1, exhibits bad decomposition
results if reduced, thus validating the reliability of the parameter β.
We are confident that our method will lead to a better approach to
real time applications.
Abstract: Unlike this study focused extensively on trading
behavior of option market, those researches were just taken their
attention to model-driven option pricing. For example, Black-Scholes
(B-S) model is one of the most famous option pricing models.
However, the arguments of B-S model are previously mentioned by
some pricing models reviewing. This paper following suggests the
importance of the dynamic character for option pricing, which is also
the reason why using the genetic algorithm (GA). Because of its
natural selection and species evolution, this study proposed a hybrid
model, the Genetic-BS model which combining GA and B-S to
estimate the price more accurate. As for the final experiments, the
result shows that the output estimated price with lower MAE value
than the calculated price by either B-S model or its enhanced one,
Gram-Charlier garch (G-C garch) model. Finally, this work would
conclude that the Genetic-BS pricing model is exactly practical.
Abstract: Video sensor networks operate on stringent requirements
of latency. Packets have a deadline within which they have
to be delivered. Violation of the deadline causes a packet to be
treated as lost and the loss of packets ultimately affects the quality
of the application. Network latency is typically a function of many
interacting components. In this paper, we propose ways of reducing
the forwarding latency of a packet at intermediate nodes. The
forwarding latency is caused by a combination of processing delay
and queueing delay. The former is incurred in order to determine the
next hop in dynamic routing. We show that unless link failures in a
very specific and unlikely pattern, a vast majority of these lookups
are redundant. To counter this we propose source routing as the
routing strategy. However, source routing suffers from issues related
to scalability and being impervious to network dynamics. We propose
solutions to counter these and show that source routing is definitely
a viable option in practical sized video networks. We also propose a
fast and fair packet scheduling algorithm that reduces queueing delay
at the nodes. We support our claims through extensive simulation on
realistic topologies with practical traffic loads and failure patterns.
Abstract: Brucellosis is a zoonotic disease; its symptoms and appearances are not exclusive in human and its traditional diagnosis is based on culture, serological methods and conventional PCR. For more sensitive, specific detection and differentiation of Brucella spp., the real time PCR method is recommended. This research has performed to determine the presence and prevalence of Brucella spp. and differentiation of Brucella abortus and Brucella melitensis in house mouse (Mus musculus) in west of Iran. A TaqMan analysis and single-step PCR was carried out in total 326 DNA of Mouse's spleen samples. From the total number of 326 samples, 128 (39.27%) gave positive results for Brucella spp. by conventional PCR, also 65 and 32 out of the 128 specimens were positive for B. melitensis, B. abortus, respectively. These results indicate a high presence of this pathogen in this area and that real time PCR is considerably faster than current standard methods for identification and differentiation of Brucella species. To our knowledge, this study is the first prevalence report of direct identification and differentiation of B. abortus and B. melitensis by real time PCR in mouse tissue samples in Iran.
Abstract: The objective of this paper is to design a model of human vital sign prediction for decreasing prediction error by using two states mapping based time series neural network BP (back-propagation) model. Normally, lot of industries has been applying the neural network model by training them in a supervised manner with the error back-propagation algorithm for time series prediction systems. However, it still has a residual error between real value and prediction output. Therefore, we designed two states of neural network model for compensation of residual error which is possible to use in the prevention of sudden death and metabolic syndrome disease such as hypertension disease and obesity. We found that most of simulations cases were satisfied by the two states mapping based time series prediction model compared to normal BP. In particular, small sample size of times series were more accurate than the standard MLP model. We expect that this algorithm can be available to sudden death prevention and monitoring AGENT system in a ubiquitous homecare environment.
Abstract: The research focuses on the effects of polyphenols
extracted from Sambucus nigra fruit, using an experimental arterial
hypertension pattern, as well as their influence on the oxidative
stress. The results reveal the normalization of the reduced glutathion
concentration, as well as a considerable reduction in the
malondialdehide serum concentration by the polyphenolic protection.
The rat blood pressure values were recorded using a CODATM
system, which uses a non-invasive blood pressure measuring method.
All the measured blood pressure components revealed a biostatistically
significant (p
Abstract: In this paper, we propose a novel adaptive
spatiotemporal filter that utilizes image sequences in order to remove
noise. The consecutive frames include: current, previous and next
noisy frames. The filter proposed in this paper is based upon the
weighted averaging pixels intensity and noise variance in image
sequences. It utilizes the Appropriate Number of Consecutive Frames
(ANCF) based on the noisy pixels intensity among the frames. The
number of consecutive frames is adaptively calculated for each
region in image and its value may change from one region to another
region depending on the pixels intensity within the region. The
weights are determined by a well-defined mathematical criterion,
which is adaptive to the feature of spatiotemporal pixels of the
consecutive frames. It is experimentally shown that the proposed
filter can preserve image structures and edges under motion while
suppressing noise, and thus can be effectively used in image
sequences filtering. In addition, the AWA filter using ANCF is
particularly well suited for filtering sequences that contain segments
with abruptly changing scene content due to, for example, rapid
zooming and changes in the view of the camera.
Abstract: In this paper, a fragile watermarking scheme is proposed for color image specified object-s authentication. The color image is first transformed from RGB to YST color space, suitable for watermarking the color media. The T channel corresponds to the chrominance component of a color image andYS ÔèÑ T , therefore selected for embedding the watermark. The T channel is first divided into 2×2 non-overlapping blocks and the two LSBs are set to zero. The object that is to be authenticated is also divided into 2×2 nonoverlapping blocks and each block-s intensity mean is computed followed by eight bit encoding. The generated watermark is then embedded into T channel randomly selected 2×2 block-s LSBs using 2D-Torus Automorphism. Selection of block size is paramount for exact localization and recovery of work. The proposed scheme is blind, efficient and secure with ability to detect and locate even minor tampering applied to the image with full recovery of original work. The quality of watermarked media is quite high both subjectively and objectively. The technique is suitable for class of images with format such as gif, tif or bitmap.
Abstract: A number of mass spectrometry applications are already available as web-based and windows-based systems to calculate isotope pattern and to display the mass spectrum based on the specific molecular formula besides providing necessary information. These applications were evaluated and compared with our new alternative application called Theoretical Isotope Generator (TIG) in terms of its functionality and features provided to prove this new application is working better and performing well. TIG provides extra features than others, complete with several functionality such as drawing, normalizing and zooming the generated graph that convey with the molecular information in a number of formats by providing the details of the calculation and molecules. Thus, any chemist, students, lecturers and researchers from anywhere could use TIG to gain related information on molecules and their relative intensity.
Abstract: We propose a novel prioritized limited
processor-sharing (PS) rule and a simulation algorithm for the performance evaluation of this rule. The performance measures of practical interest are evaluated using this algorithm. Suppose that there
are two classes and that an arriving (class-1 or class-2) request encounters n1 class-1 and n2 class-2 requests (including the arriving
one) in a single-server system. According to the proposed rule, class-1
requests individually and simultaneously receive m / (m * n1+ n2) of the service-facility capacity, whereas class-2 requests receive 1 / (m *n1 + n2) of it, if m * n1 + n2 ≤ C. Otherwise (m * n1 + n2 > C), the arriving request will be queued in the corresponding class waiting
room or rejected. Here, m (1) denotes the priority ratio, and C ( ∞), the service-facility capacity. In this rule, when a request arrives at [or
departs from] the system, the extension [shortening] of the remaining
sojourn time of each request receiving service can be calculated using
the number of requests of each class and the priority ratio. Employing
a simulation program to execute these events and calculations enables
us to analyze the performance of the proposed prioritized limited PS
rule, which is realistic in a time-sharing system (TSS) with a
sufficiently small time slot. Moreover, this simulation algorithm is
expanded for the evaluation of the prioritized limited PS system with
N 3 priority classes.
Abstract: The flow field in a centrifugal fan is highly complex
with flow reversal taking place on the suction side of impeller and
diffuser vanes. Generally performance of the centrifugal fan could be
enhanced by judiciously introducing splitter vanes so as to improve
the diffusion process. An extensive numerical whole field analysis on
the effect of splitter vanes placed in discrete regions of suspected
separation points is possible using CFD. This paper examines the
effect of splitter vanes corresponding to various geometrical
locations on the impeller and diffuser. The analysis shows that the
splitter vanes located near the diffuser exit improves the static
pressure recovery across the diffusing domain to a larger extent. Also
it is found that splitter vanes located at the impeller trailing edge and
diffuser leading edge at the mid-span of the circumferential distance
between the blades show a marginal improvement in the static
pressure recovery across the fan. However, splitters provided near to
the suction side of the impeller trailing edge (25% of the
circumferential gap between the impeller blades towards the suction
side), adversely affect the static pressure recovery of the fan.
Abstract: The heterotrophic seedling growth can be defined as a
product of two components: (1) the weight of mobilized seed reserve,
and (2) conversion efficiency of utilized seed reserve to seedling
tissue. The first component can be further divided into (1) initial seed
weight, and (2) the fraction of seed reserve, which is mobilized. The
objective of this study was the identification of the sensitive seedling
growth component(s) in response to drought and salinity stresses.
Two experiments were separately conducted using various salinity
levels (osmotic pressure) of 0, 0.25, 0.50, 0.75, 1, 1.25 and 1.5 MPa
created using NaCl as first experiment and by polyethylene glycol
(drought stress) of 0, 0.2, 0.4, 0.6, 0.8, 1, 1.2 and 1.4 MPa in second
experiment. Seeds of five crops species (Hordeum vulgare, Brassica
napus, Zea mays, Medicago sativa and Medicago scutellata) were
used in each experiment. In both experiments, seedling growth,
fraction of seed reserve utilization and weight of mobilized seed
reserve decreased with increasing drought and salt intensity.
However, drought and salinity stresses had no effect on the
conversion efficiency. It was concluded that the sensitive component
of seedling growth is the weight of mobilized seed reserve.
Abstract: In this paper we report the technique of optical
induction of 2 and 3-dimensional (2D and 3D) photonic lattices in
photorefractive materials based on diffraction grating self replication
-Talbot effect. 1D and 2D different rotational symmery diffraction
masks with the periods of few tens micrometers and 532 nm cw laser
beam were used in the experiments to form an intensity modulated
light beam profile. A few hundred micrometric scale replications of
mask generated intensity structures along the beam propagation axis
were observed. Up to 20 high contrast replications were detected for
1D annular mask with 30
Abstract: A self-association model has been used to understand
the concentration dependence of free energy of mixing (GM), heat of
mixing (HM), entropy of mixing (SM), activity (a) and microscopic
structures, such as concentration fluctuation in long wavelength limit
(Scc(0)) and Warren-Cowley short range order parameter ( 1
α )for Cu-
Tl molten alloys at 1573K. A comparative study of surface tension of
the alloys in the liquid state at that temperature has also been carried
out theoretically as function of composition in the light of Butler-s
model, Prasad-s model and quasi-chemical approach. Most of the
computed thermodynamic properties have been found in agreement
with the experimental values. The analysis reveals that the Cu-Tl
molten alloys at 1573K represent a segregating system at all
concentrations with moderate interaction. Surface tensions computed
from different approaches have been found to be comparable to each
other showing increment with the composition of copper.