Abstract: Distributed Generation (DG) systems are considered an integral part in future distribution system planning. Appropriate size and location of distributed generation plays a significant role in minimizing power losses in distribution systems. Among the benefits of distributed generation is the reduction in active power losses, which can improve the system performance, reliability and power quality. In this paper, Artificial Bee Colony (ABC) algorithm is proposed to determine the optimal DG-unit size and location by loss sensitivity index in order to minimize the real power loss, total harmonic distortion (THD) and voltage sag index improvement. Simulation study is conducted on 69-bus radial test system to verify the efficacy of the proposed method.
Abstract: By hand pollination was conducted to evaluated different pollen sources and their affects on fruit set and quality of wax apple. The following parameters were recorded: fruit set, seed set, fruit characteristics. Results showed that fruit set percentage with seed were significantly high in ‘Long Red B’ when ‘Black’, ‘Thyto’ were used as pollen parents. Pollen of ‘Black’, ‘Thyto’ resulted in high fruit weight, fruit diameter, fruit length, bigger flesh thickness, better total soluble solids as compared with other pollens. The observation of pollen-growth in vitro revealed that pollen germination at 15% sucrose concentration are required for optimum pollen germination with the high pollen germination were found in ‘Black’, ‘Thyto’. From the result, we concluded that ‘Black’, ‘Thyto’ were proved to be good pollinizers in ‘Long Red B’. Therefore, artificial cross-pollination using ‘Black’, ‘Thyto’ as pollinizers were strongly recommended for ‘Long Red B’ cultivar in wax apple orchard.
Abstract: The present research study analyses the students’ satisfaction with university performance regarding the reliability dimension, ability of professors and staff to perform the promised services with quality to students in the post-graduate courses offered by Sri Venkateswara University in India. The research is done with the notion that the student compares the perceived performance with prior expectations. Customer satisfaction is seen as the outcome of this comparison. The sample respondents were administered with schedule based on stratified random technique for this study. Statistical techniques such as factor analysis, t-test and correlation analysis were used to accomplish the respective objectives of the study.
Abstract: This paper aims to introduce the allopatry of national college entrance examination which allow migrant students enter senior high schools and take college entrance exam where they live, identifies the reasons affect the implementation of this policy in the Chinese context. Most of China’s provinces and municipalities recently have announced new policies regarding national college entrance exams for non-local students. The paper conducts SWOT analysis reveals the opportunities, strength, weakness and challenges of the scheme, so as to discuss the implementation strategies from the perspectives of idea and institution. The research findings imply that the government should take a more positive attitude toward relaxing the allopatry of NCEE policy restrictions, and promote the reform household registration policy and NCEE policy with synchronous operations. Higher education institutions should explore the diversification of enrollment model; the government should issue the authority of universities and colleges to select elite migrant students beyond the restrictions of NCEE. To suit reform policies to local conditions, the big cities such as Beijing, Shanghai and Guangzhou should publish related compensate measures for children of migrant workers access to higher vocational colleges with tuition fee waivered.
Abstract: Understanding the behavior of airflow in a room is essential for building designers to provide the most efficient design of ventilation system, and having acceptable indoor air quality. This trend is the motive to solve the relationship between airflow parameters and thermal comfort. This paper investigates airflow characteristics, indoor air quality (IAQ), and the thermal comfort (TC) in a ventilated room with a displacement ventilation system using three dimensional CFD code [AirPak 2.0.6]. After validation of the code, a numerical study is executed for a typical room with dimensions of 5m by 3m by 3m height according to a variety of supply air velocities, supply air temperature and supply air relative humidity. The finite volume method and the indoor zero equation turbulence models are employed for solving the governing equations numerically. The temperature field and the mean age of air (MAA) in the modeled room for a displacement ventilation system are determined according to a variety of the above parameters. The variable air volume (VAV) systems with different supply air velocity are applicable to control room air temperature for a displacement ventilation system.
Abstract: The effectiveness of a commercial bee attractant, synthetic honey bee queen mandibular pheromone (Fruit Boost®) for enhancing pollination of Gossypium hirsutum was evaluated in a transgenic (Bt) cotton crop. The study assessed the number of bee visitations to blossoms of plants treated with Fruit Boost® as well, as effects on fruit set, yield, and lint quality. Bee activity on plots sprayed with pheromone concentrations of 50 and 500 queen equivalents (QEQ) /ha did not differ significantly from water-only control, on the day of application or the subsequent day. Application of the pheromone did not increase fruit set, yield, or lint quality. Two consecutive pheromone applications, applied two days apart, were not significantly different from a single application for any parameter.
Abstract: Geophagic and cosmetic clays are among potential nanomaterial which occur naturally and are of various forms. The use of these nanoclays is a common practice in both rural and urban areas mostly due to tradition and medicinal reasons. These naturally occurring materials can be valuable sources of nanomaterial by serving as nanocomposites. The need to ascertain the safety of these materials is the motivation for this research. Physical Characterization based on the hue value and microbiological qualities of the nanoclays were carried out. The Microbial analysis of the clay samples showed considerable contamination with both bacteria and fungi with fungal contaminants taking the lead. This observation may not be unlikely due to the ability of fungi species to survive harsher growth conditions than bacteria. ‘Atike pupa’ showed no bacterial growth. The clay with the largest bacterial count was Calabash chalk (Igbanke), while that with the highest fungal count was ‘Eko grey’. The most commonly isolated bacteria in this study were Clostridium spp. and Corynebacterium spp. while fungi included Aspergillus spp. These results are an indication of the need to subject these clay materials to treatments such as heating before consumption or topical usage thereby ascertaining their safety.
Abstract: Drought stress is a critical environmental factor that adversely affects crop productivity and quality. Because of their immobile nature, plants have evolved mechanisms to sense and respond to drought stress. We identified a novel locus of Arabidopsis, designated DRA1 (drought responsive ankyrin1), whose disruption leads to increased drought-stress tolerance. DRA1 encodes a transmembrane protein with an ankyrin-repeat motif that has been implicated in diverse cellular processes such as signal transduction. RT-PCR analysis revealed that there were at least two splicing variants of DRA1 transcripts in wild-type plants. In response to drought stress, the levels of DRA1 transcripts retaining second and third introns were increased, whereas these introns were removed under unstressed conditions. These results suggest that DRA1 protein may negatively regulate plant drought tolerance and that the expression of DRA1is regulated in response to drought stress by alternative splicing.
Abstract: Constantly changing economic conditions require companies to design their production to be more economical, innovative, and flexible. Since workers have a decisive influence on cost, time, and quality, e.g. by monitoring indicators that determine quality, by developing processes more resistant to disturbances, or by monitoring environmental standards, a focus on personnel as a production factor is needed. This presupposes the efficient use and systematic enhancement of employees’ existing competences since greater consideration of these aspects in work planning will help to enhance competitiveness. The aim of the research project ‘Integrated Technology- and Competence-based Work Planning in Socio-Technical Systems’ is to develop a new work planning method that combines technology with work science by incorporating employees’ skills as a quality indicator. For employee competences to increase competitiveness, it is first of all necessary to assess how competences affect cost, time, and quality. A model for deriving predictions about the effects of competence-based parameters on these strategic business objectives is developed in this paper.
Abstract: Since the late 1970s, quality management has become an important tool for achieving a high quality of public e-administration services in many countries. Very important part of quality management in e-administration is measurement of quality indicators related to this sector. Therefore, this paper gives a description of e-administration, including statistics about it and other examples from many countries worldwide, as well as the explanation of quality management in public e-administration. The paper also gives a list and description of quality indicators relevant to e-administration, as part of quality management within the e-administration. Through a literature review and best practices, the paper aims to analyze quality indicators measurement and other parts of good quality management when it comes to the public e-administration and consequently to show the usefulness of quality management in public e-administration in order to provide services of high quality.
Abstract: Power quality is used to describe the degree of consistency of electrical energy expected from generation source to point of use. The term power quality refers to a wide variety of electromagnetic phenomena that characterize the voltage and current at a given time and at a given location on the power system. Power quality problems can be defined as problem that results in failure of customer equipments, which manifests itself as an economic burden to users, or produces negative impacts on the environment. Voltage stability, power factor, harmonics pollution, reactive power and load unbalance are some of the factors that affect the consistency or the quality level. This research proposal proposes to investigate and analyze the causes and effects of power quality to homes and industries in Sarawak. The increasing application of electronics equipment used in the industries and homes has caused a big impact on the power quality. Many electrical devices are now interconnected to the power network and it can be observed that if the power quality of the network is good, then any loads connected to it will run smoothly and efficiently. On the other hand, if the power quality of the network is bad, then loads connected to it will fail or may cause damage to the equipments and reduced its lifetime. The outcome of this research will enable better and novel solutions of poor power quality to small industries and reduce damage of electrical devices and products in the industries.
Abstract: Knowledge is increasingly recognised in this, the
knowledge era, as a strategic resource, by public sector organisations,
in view of the public sector reform initiatives. People and knowledge
play a vital role in attaining improved organisational performance
and high service quality. Many government departments in the public
sector have started to realise the importance of knowledge
management in streamlining their operations and processes. This
study focused on knowledge management in the public healthcare
service organisations, where the concept of service provider
competitiveness pales to insignificance, considering the huge
challenges emanating from the healthcare and public sector reforms.
Many government departments are faced with challenges of
improving organisational performance and service delivery,
improving accountability, making informed decisions, capturing the
knowledge of the aging workforce, and enhancing partnerships with
stakeholders.
The purpose of this paper is to examine the knowledge
management practices of the Gauteng Department of Health in South
Africa, in order to understand how knowledge management practices
influence improvement in organisational performance and healthcare
service delivery. This issue is explored through a review of literature
on dominant views on knowledge management and healthcare service
delivery, as well as results of interviews with, and questionnaire
responses from, the general staff of the Gauteng Department of
Health. Web-based questionnaires, face-to-face interviews and
organisational documents were used to collect data. The data were
analysed using both the quantitative and qualitative methods. The
central question investigated was: To what extent can the conditions
required for successful knowledge management be observed, in order
to improve organisational performance and healthcare service
delivery in the Gauteng Department of Health.
The findings showed that the elements of knowledge management
capabilities investigated in this study, namely knowledge creation,
knowledge sharing and knowledge application, have a positive,
significant relationship with all measures of organisational
performance and healthcare service delivery. These findings thus
indicate that by employing knowledge management principles, the
Gauteng Department of Health could improve its ability to achieve its
operational goals and objectives, and solve organisational and
healthcare challenges, thereby improving organisational performance
and enhancing healthcare service delivery in Gauteng.
Abstract: Customer audits are generally used to ensure customer
that supplier is continuously able to meet his requirements while
supplying him required products and services. However, customer
audits can be considered as a very useful quality control tool for
suppliers as well. In our paper, we analyzed the process of customer
audits realized in Czech companies from both perspectives: a
supplier´s viewpoint and customer´s viewpoint. At the end, we tried
to emphasize some areas that should not be omitted during the audit
process.
Abstract: A new Meta heuristic approach called "Randomized gravitational emulation search algorithm (RGES)" for solving large size set covering problems has been designed. This algorithm is found upon introducing randomization concept along with the two of the four primary parameters -velocity- and -gravity- in physics. A new heuristic operator is introduced in the domain of RGES to maintain feasibility specifically for the set covering problem to yield best solutions. The performance of this algorithm has been evaluated on a large set of benchmark problems from OR-library. Computational results showed that the randomized gravitational emulation search algorithm - based heuristic is capable of producing high quality solutions. The performance of this heuristic when compared with other existing heuristic algorithms is found to be excellent in terms of solution quality.
Abstract: The freezing point of milk is in important indicator of
the milk quality. The freezing point of milk is determined primarily
to prove milk adulteration with water and to determine the amount of
water in it. Chemical composition and properties of milk, thermal
treatment and presence of any substance can influence freezing point
of product. There are different substances, which can be added to
milk with main purpose to prolong shelf-life of raw milk. There are
detergent, preservatives, formaldehyde, hydrogen peroxide,
antibiotics, sodium carbonate, and hydrogen peroxide. Therefore the
aim of the present study was to determine freezing point of milk,
skimmed milk, pasteurized milk and milk with different substances
(formaldehyde, antibiotics, sodium carbonate, hydrogen peroxide,
disinfectant, and detergent) in different concentrations. The thermal
treatment and different undesirable substances presence in milk have
significant influence on freezing point of it.
Abstract: Software Reusability is primary attribute of software
quality. There are metrics for identifying the quality of reusable
components but the function that makes use of these metrics to find
reusability of software components is still not clear. These metrics if
identified in the design phase or even in the coding phase can help us
to reduce the rework by improving quality of reuse of the component
and hence improve the productivity due to probabilistic increase in
the reuse level. In this paper, we have devised the framework of
metrics that uses McCabe-s Cyclometric Complexity Measure for
Complexity measurement, Regularity Metric, Halstead Software
Science Indicator for Volume indication, Reuse Frequency metric
and Coupling Metric values of the software component as input
attributes and calculated reusability of the software component. Here,
comparative analysis of the fuzzy, Neuro-fuzzy and Fuzzy-GA
approaches is performed to evaluate the reusability of software
components and Fuzzy-GA results outperform the other used
approaches. The developed reusability model has produced high
precision results as expected by the human experts.
Abstract: Mostly transforms are used for speech data
compressions which are lossy algorithms. Such algorithms are
tolerable for speech data compression since the loss in quality is not
perceived by the human ear. However the vector quantization (VQ)
has a potential to give more data compression maintaining the same
quality. In this paper we propose speech data compression algorithm
using vector quantization technique. We have used VQ algorithms
LBG, KPE and FCG. The results table shows computational
complexity of these three algorithms. Here we have introduced a new
performance parameter Average Fractional Change in Speech
Sample (AFCSS). Our FCG algorithm gives far better performance
considering mean absolute error, AFCSS and complexity as
compared to others.
Abstract: Urbanization has been found to impact stormwater
runoff quantity and quality. A study catchment with mixed land use,
residential and industrial were investigated and the water quality
discharged from the catchment were sampled and tested for four
basic water quality parameters; BOD5, NH3-N, NO3-N and P. One
dry weather flow and several stormwater runoff were sampled.
Results were compared to the USEPA stormwater quality benchmark
values and the Interim National Water Quality Standards for
Malaysia (INWQS). The concentration of the parameters was found
to vary significantly between storms and the pollutant of concern was
found to be NO3-N.
Abstract: Heavy metal transfer in soil profiles is a major
environmental concern because even slow transport through the soil
may eventually lead to deterioration of groundwater quality. The use
of sewage sludge and effluents from wastewater treatment plants for
irrigation of agricultural lands is on the rise particularly in peri-urban
area of developing countries. In this study soil samples under sludge
application and wastewater irrigation were studied and soil samples
were collected in the soil profiles from the surface to 100 cm in
depth. For this purpose, three plots were made in a treatment plant in
south of Tehran-Iran. First plot was irrigated just with effluent from
wastewater treatment plant, second plot with simulated heavy metals
concentration equal 50 years irrigation and in third plot sewage
sludge and effluent was used. Trace metals concentration (Cd, Cu)
were determined for soil samples. The results indicate movement of
metals was observed, but the most concentration of metals was found
in topsoil samples. The most of Cadmium concentration was
measured in the topsoil of plot 3, 4.5mg/kg and Maximum cadmium
movement was observed in 0-20 cm. The most concentration of
copper was 27.76mg/kg, and maximum percolation in 0-20 cm.
Metals (Cd, Cu) were measured in leached water. Preferential flow
and metal complexation with soluble organic apparently allow
leaching of heavy metals.
Abstract: Celiac disease is an immune-mediated disease, triggered in genetically susceptible individuals by ingested gluten from wheat, rye, barley and other closely related cereal grains. The only effective treatment is a strict gluten free diet for life. Latvian producers do not offer gluten-free products. In this research, use of extruded maize flour was tested for substituting rice, maize or buckwheat flour in gluten-free bread formulations at different ratios. Also the influence of extruded maize flour on the quality parameters of gluten-free bread was investigated. The aim of research was to study the influence of extruded maize flour on gluten-free bread quality. Addition of extruded maize flour affect gluten-free bread crumb color, structure of crumb, weight loss and dry off of bread.