Abstract: Speed sensorless systems are intensively studied during recent years; this is mainly due to their economical benefit and fragility of mechanical sensors and also the difficulty of installing this type of sensor in many applications. These systems suffer from instability problems and sensitivity to parameter mismatch at low speed operation. In this paper an analysis of adaptive observer stability with stator resistance estimation is given.
Abstract: A numerical study has been carried out to investigate
the heat transfer by natural convection of nanofluid taking Cu as
nanoparticles and the water as based fluid in a three dimensional
annulus enclosure filled with porous media (silica sand) between two
horizontal concentric cylinders with 12 annular fins of 2.4mm
thickness attached to the inner cylinder under steady state conditions.
The governing equations which used are continuity, momentum and
energy equations under an assumptions used Darcy law and
Boussinesq-s approximation which are transformed to dimensionless
equations. The finite difference approach is used to obtain all the
computational results using the MATLAB-7. The parameters affected
on the system are modified Rayleigh number (10 ≤Ra*≤ 1000), fin
length Hf (3, 7 and 11mm), radius ratio Rr (0.293, 0.365 and 0.435)
and the volume fraction(0 ≤ ¤ò ≤ 0 .35). It was found that the
average Nusselt number depends on (Ra*, Hf, Rr and φ). The results
show that, increasing of fin length decreases the heat transfer rate and
for low values of Ra*, decreasing Rr cause to decrease Nu while for
Ra*
greater than 100, decreasing Rr cause to increase Nu and adding
Cu nanoparticles with 0.35 volume fraction cause 27.9%
enhancement in heat transfer. A correlation for Nu in terms of Ra*,
Hf and φ, has been developed for inner hot cylinder.
Abstract: This paper presents the results of an analytical study
on the seismic response of a Multi-Span-Simply-Supported precast
bridge in Washington State. The bridge was built in the early 1960's
along Interstate 5 and was widened the first time in 1979 and the
second time in 2001. The primary objective of this research project
is to determine the seismic vulnerability of the bridge in order to
develop the required retrofit measure. The seismic vulnerability of
the bridge is evaluated using two seismic evaluation methods
presented in the FHWA Seismic Retrofitting Manual for Highway
Bridges, Method C and Method D2. The results of the seismic
analyses demonstrate that Method C and Method D2 vary markedly
in terms of the information they provide to the bridge designer
regarding the vulnerability of the bridge columns.
Abstract: Business rules and data warehouse are concepts and
technologies that impact a wide variety of organizational tasks. In
general, each area has evolved independently, impacting application
development and decision-making. Generating knowledge from data
warehouse is a complex process. This paper outlines an approach to
ease import of information and knowledge from a data warehouse
star schema through an inference class of business rules. The paper
utilizes the Oracle database for illustrating the working of the
concepts. The star schema structure and the business rules are stored
within a relational database. The approach is explained through a
prototype in Oracle-s PL/SQL Server Pages.
Abstract: This paper describes a code clone visualization method, called FC graph, and the implementation issues. Code clone detection tools usually show the results in a textual representation. If the results are large, it makes a problem to software maintainers with understanding them. One of the approaches to overcome the situation is visualization of code clone detection results. A scatter plot is a popular approach to the visualization. However, it represents only one-to-one correspondence and it is difficult to find correspondence of code clones over multiple files. FC graph represents correspondence among files, code clones and packages in Java. All nodes in FC graph are positioned using force-directed graph layout, which is dynami- cally calculated to adjust the distances of nodes until stabilizing them. We applied FC graph to some open source programs and visualized the results. In the author’s experience, FC graph is helpful to grasp correspondence of code clones over multiple files and also code clones with in a file.
Abstract: This paper proposes a simple model of economic geography within the Dixit-Stiglitz-Iceberg framework that may be used to analyze migration patterns among three cities. The cost–benefit tradeoffs affecting incentives for three types of migration, including echelon migration, are discussed. This paper develops a tractable, heterogeneous-agent, general equilibrium model, where agents share constant human capital, and explores the relationship between the benefits of echelon migration and gross human capital. Using Chinese numerical solutions, we study the manifestation of echelon migration and how it responds to changes in transportation cost and elasticity of substitution. Numerical results demonstrate that (i) there are positive relationships between a migration-s benefit-and-wage ratio, (ii) there are positive relationships between gross human capital ratios and wage ratios as to origin and destination, and (iii) we identify 13 varieties of human capital convergence among cities. In particular, this model predicts population shock resulting from the processes of migration choice and echelon migration.
Abstract: In this paper, an analytical approach for free vibration
analysis of four edges simply supported rectangular Kirchhoff plates
is presented. The method is based on wave approach. From wave
standpoint vibration propagate, reflect and transmit in a structure.
Firstly, the propagation and reflection matrices for plate with simply
supported boundary condition are derived. Then, these matrices are
combined to provide a concise and systematic approach to free
vibration analysis of a simply supported rectangular Kirchhoff plate.
Subsequently, the eigenvalue problem for free vibration of plates is
formulated and the equation of plate natural frequencies is
constructed. Finally, the effectiveness of the approach is shown by
comparison of the results with existing classical solution.
Abstract: The Kowsar dam supply water for different usages
such as drinking, industrial, agricultural and aquaculture farms
usages and located next to the city of Dehdashat in Kohgiluye and
Boyerahmad province in southern Iran. There are some towns and
villages on the Kowsar dam watersheds, which Dehdasht and
Choram are the most important and populated cities in this area. The
study was undertaken to assess the status of water quality in the
urban areas of the Kowsar dam. A total of 28 water samples were
collected from 6 stations on surface water and 1 station from
groundwater on the watershed of the Kowsar dam. All the samples
were analyzed for Cd concentration using standard procedures. The
results were compared with other national and international
standards. Among the analyzed samples, as the maximum value of
cadmium (1.131 μg/L) was observed on the station 2 at the winter
2009, all the samples analyzed were within the maximum admissible
limits by the United States Environmental Protection Agency, EU,
WHO, New Zealand , Australian, Iranian, and the Indian standards.
In general results of the present study have shown that Cd mean
values of stations No. 4, 1 and 2 with 0.5135, 0.0.4733 and 0.4573
μg/L respectively are higher than the other stations . Although Cd
level of all samples and stations have had normal values but this is
an indication of pollution potential and hazards because of human
activity and waste water of towns in the areas, which can effect on
human health implications in future. This research, therefore,
recommends the government and other responsible authorities to take
suitable improving measures in the Kowsar dam watershed-s.
Abstract: The present work demonstrates the design and simulation of a fuzzy control of an air conditioning system at different pressures. The first order Sugeno fuzzy inference system is utilized to model the system and create the controller. In addition, an estimation of the heat transfer rate and water mass flow rate injection into or withdraw from the air conditioning system is determined by the fuzzy IF-THEN rules. The approach starts by generating the input/output data. Then, the subtractive clustering algorithm along with least square estimation (LSE) generates the fuzzy rules that describe the relationship between input/output data. The fuzzy rules are tuned by Adaptive Neuro-Fuzzy Inference System (ANFIS). The results show that when the pressure increases the amount of water flow rate and heat transfer rate decrease within the lower ranges of inlet dry bulb temperatures. On the other hand, and as pressure increases the amount of water flow rate and heat transfer rate increases within the higher ranges of inlet dry bulb temperatures. The inflection in the pressure effect trend occurs at lower temperatures as the inlet air humidity increases.
Abstract: Sorting appears the most attention among all computational tasks over the past years because sorted data is at the heart of many computations. Sorting is of additional importance to parallel computing because of its close relation to the task of routing data among processes, which is an essential part of many parallel algorithms. Many parallel sorting algorithms have been investigated for a variety of parallel computer architectures. In this paper, three parallel sorting algorithms have been implemented and compared in terms of their overall execution time. The algorithms implemented are the odd-even transposition sort, parallel merge sort and parallel rank sort. Cluster of Workstations or Windows Compute Cluster has been used to compare the algorithms implemented. The C# programming language is used to develop the sorting algorithms. The MPI (Message Passing Interface) library has been selected to establish the communication and synchronization between processors. The time complexity for each parallel sorting algorithm will also be mentioned and analyzed.
Abstract: In this paper, based on the coupled-mode and carrier rate equations, derivation of a dynamic model and numerically analysis of a MQW chirped DFB-SOA all-optical flip-flop is done precisely. We have analyzed the effects of strains of QW and MQW and cross phase modulation (XPM) on the dynamic response, and rise and fall times of the DFB-SOA all optical flip flop. We have shown that strained MQW active region in under an optimized condition into a DFB-SOA with chirped grating can improve the switching ON speed limitation in such a of the device, significantly while the fall time is increased. The values of the rise times for such an all optical flip-flop, are obtained in an optimized condition, areas tr=255ps.
Abstract: A Rotary Disc Contactor with inner diameter of
9.1cm and maximum operating height of 40cm has been used to
investigate break up phenomenon. Water-Toluene, Water as
continuous phase and Toluene as dispersed phase, was selected as
chemical system in the experiments. The mentioned chemical system
has high interfacial tension so it was possible to form big drops
which permit accurate investigation on break up phenomenon as well
as the first and second critical rotor speeds.
In this study, Break up phenomenon has been studied as a function
of mother drop size, rotor speed and continuous phase height. Further
more; the effects of mother drop size and continuous phase height on
the first and second critical rotor speeds were investigated. Finally,
two modified correlations were proposed to estimate the first and
second critical speeds.
Abstract: Over the past years, the EMCCD has had a profound
influence on photon starved imaging applications relying on its unique
multiplication register based on the impact ionization effect in the
silicon. High signal-to-noise ratio (SNR) means high image quality.
Thus, SNR improvement is important for the EMCCD. This work
analyzes the SNR performance of an EMCCD with gain off and on. In
each mode, simplified SNR models are established for different
integration times. The SNR curves are divided into readout noise (or
CIC) region and shot noise region by integration time. Theoretical
SNR values comparing long frame integration and frame adding in
each region are presented and discussed to figure out which method is
more effective. In order to further improve the SNR performance,
pixel binning is introduced into the EMCCD. The results show that
pixel binning does obviously improve the SNR performance, but at the
expensive of the spatial resolution.
Abstract: Random Oracle Model (ROM) is an effective method
for measuring the practical security of cryptograph. In this paper, we
try to use it into information hiding system (IHS). Because IHS has its
own properties, the ROM must be modified if it is used into IHS.
Firstly, we fully discuss why and how to modify each part of ROM
respectively. The main changes include: 1) Divide the attacks that IHS
may be suffered into two phases and divide the attacks of each phase
into several kinds. 2) Distinguish Oracles and Black-boxes clearly. 3)
Define Oracle and four Black-boxes that IHS used. 4) Propose the
formalized adversary model. And 5) Give the definition of judge.
Secondly, based on ROM of IHS, the security against known original
cover attack (KOCA-KOCA-security) is defined. Then, we give an
actual information hiding scheme and prove that it is
KOCA-KOCA-secure. Finally, we conclude the paper and propose the
open problems of further research.
Abstract: The efficiency of chitosan beads processed from 4
marine animal shells; white leg shrimp (Litopenaeus vannamei), mud
crab (Scylla sp.), horseshoe crab (Carcinoscorpius rotundicauda),
and cuttlefish bone (Sepia sp.), for the adsorption experiments of
ammonia and formaldehyde were investigated. The porosities of
chitosan from the shells looked like beads were distinctly examined
under SEM. The original pores of those shells on the surface areas
compose of evenly fine pores. The shell beads of cuttlefish bone and
horseshoe crab show the larger probably even porosity, while on
those white leg shrimp and mud crab contain various large and fine
pores. The best adsorption at pH 9 in 18 mg/l ammonia at 2 hours
yield on cuttlefish bone, horseshoe crab, mud crab and white leg
shrimp with the average percent of 59.12, 51.45, 45.66 and 43.52,
respectively. Within 30 minutes the formaldehyde absorbers (at pH 5
in 8 μg/ml) revealed 46.27, 26.56, and 18.04 percent capacities in
cuttlefish bone, mud crab and white leg shrimp beads; while 22.44
percent in the horseshoe crab at pH 7. The adsorption capacities and
the amounts of beads showed a positive correlation. The adsorption
capacity relationship between pH and the gas concentrations were
affected by these qualities of chitosan beads.
Abstract: The regional innovative competitiveness is an integrating characteristic of the innovative sphere of the region. It depends on a big variety of different parameters connected with all kinds of economic entities- activities. But management parameters shouldn't be irregular, so in order to avoid it, an institutional system should be formed. This system should carry out strategic management of factors having the greatest influence on the region's innovative development. This article is devoted to different aspects of organization of the region's development institutional mechanism, which is based on management of regional innovative competitiveness parameters. The base of the analysis is innovatively-active Russian regions which were compared according to the level of the innovative competitiveness. After that the most important parameters of successful innovative development of the region were revealed with the help of the correlation-regression analysis. The results of the research could be used for investigation of the region's innovative policy.
Abstract: This paper presents Faults Forecasting System (FFS)
that utilizes statistical forecasting techniques in analyzing process
variables data in order to forecast faults occurrences. FFS is
proposing new idea in detecting faults. Current techniques used in
faults detection are based on analyzing the current status of the
system variables in order to check if the current status is fault or not.
FFS is using forecasting techniques to predict future timing for faults
before it happens. Proposed model is applying subset modeling
strategy and Bayesian approach in order to decrease dimensionality
of the process variables and improve faults forecasting accuracy. A
practical experiment, designed and implemented in Okayama
University, Japan, is implemented, and the comparison shows that
our proposed model is showing high forecasting accuracy and
BEFORE-TIME.
Abstract: The experiment was conducted to evaluate
digestibility quantities of protein in Canola Meals (CMs) between
caecectomised and intact adult Rhode Island Red (RIR) cockerels
with using conventional addition method (CAM) for 7 d: a 4-d
adaptation and a 3-d experiment period on the basis of a completely
randomized design with 4 replicates. Results indicated that
caecectomy decreased (P
Abstract: Scatter behavior of fatigue life in die-cast AM60B
alloy was investigated. For comparison, those in rolled AM60B alloy
and die-cast A365-T5 aluminum alloy were also studied. Scatter
behavior of pore size was also investigated to discuss dominant
factors for fatigue life scatter in die-cast materials. Three-parameter
Weibull function was suitable to explain the scatter behavior of both
fatigue life and pore size. The scatter of fatigue life in die-cast
AM60B alloy was almost comparable to that in die-cast A365-T5
alloy, while it was significantly large compared to that in the rolled
AM60B alloy. Scatter behavior of pore size observed at fracture
nucleation site on the fracture surface was comparable to that
observed on the specimen cross-section and also to that of fatigue
life. Therefore, the dominant factor for large scatter of fatigue life in
die-cast alloys would be the large scatter of pore size. This
speculation was confirmed by the fracture mechanics fatigue life
prediction, where the pore observed at fatigue crack nucleation site
was assumed as the pre-existing crack.
Abstract: This paper aims to argue that religion and Faith-based
Organizations (FBOs) contribute to building democratic process
through the provision of education in Sierra Leone. Sierra Leone
experienced a civil war from 1991 to 2002 and about 70 percent of the
population lives in poverty. While the government has been in the
process of rebuilding the nation, many forms of Civil Society
Organizations (CSOs), including FBOs, have played a significant role
in promoting social development. Education plays an important role in
supporting people-s democratic movements through knowledge
acquisition, spiritual enlightenment and empowerment. This paper
discusses religious tolerance in Sierra Leone and how FBOs have
contributed to the provision of primary education in Sierra Leone. This
study is based on the author-s field research, which involved
interviews with teachers and development stakeholders, notably
government officials, Non-governmental Organizations (NGOs) and
FBOs, as well as questionnaires completed by pupils, parents and
teachers.