Abstract: A robust wheel slip controller for electric vehicles is
introduced. The proposed wheel slip controller exploits the dynamics
of electric traction drives and conventional hydraulic brakes for
achieving maximum energy efficiency and driving safety. Due to
the control of single wheel traction motors in combination with a
hydraulic braking system, it can be shown, that energy recuperation
and vehicle stability control can be realized simultaneously. The
derivation of a sliding mode wheel slip controller accessing two
drivetrain actuators is outlined and a comparison to a conventionally
braked vehicle is shown by means of simulation.
Abstract: In a travelling wave thermoacoustic device, the
regenerator sandwiched between a pair of (hot and cold) heat
exchangers constitutes the so-called thermoacoustic core, where the
thermoacoustic energy conversion from heat to acoustic power takes
place. The temperature gradient along the regenerator caused by the
two heat exchangers excites and maintains the acoustic wave in the
resonator. The devices are called travelling wave thermoacoustic
systems because the phase angle difference between the pressure and
velocity oscillation is close to zero in the regenerator. This paper
presents the construction and testing of a thermoacoustic engine
equipped with a ceramic regenerator, made from a ceramic material
that is usually used as catalyst substrate in vehicles- exhaust systems,
with fine square channels (900 cells per square inch). The testing
includes the onset temperature difference (minimum temperature
difference required to start the acoustic oscillation in an engine), the
acoustic power output, thermal efficiency and the temperature profile
along the regenerator.
Abstract: The paper presents the potential for RES in Romania
and the results of the Romanian national research project “Romania
contribution to the European targets regarding the development of
renewable energy sources - PROMES". The objective of the project
is the development of energy generation from renewable energy
sources (RES) in Romania by drawing up scenarios and prognosis
harmonized with national and European targets, RES development
effects modeling (environmental, economic, social etc.), research of
the impact of the penetration of RES into the main, implementation
of an advanced software system tool for RES information recording
and communication, experimental research based on demonstrative
applications.
The expected results are briefly presented, as well as the social,
economic and environmental impact.
Abstract: The Long-range Energy and Alternatives Planning (LEAP) energy planning system has been developed for South Africa, for the 2005 base year and a limited number of plausible future scenarios that may have significant implications (negative or positive) in terms of environmental impacts. The system quantifies the national energy demand for the domestic, commercial, transport, industry and agriculture sectors, the supply of electricity and liquid fuels, and the resulting emissions. The South African National Energy Research Institute (SANERI) identified the need to develop an environmental assessment tool, based on the LEAP energy planning system, to provide decision-makers and stakeholders with the necessary understanding of the environmental impacts associated with different energy scenarios. A comprehensive analysis of indicators that are used internationally and in South Africa was done and the available data was accessed to select a reasonable number of indicators that could be utilized in energy planning. A consultative process was followed to determine the needs of different stakeholders on the required indicators and also the most suitable form of reporting. This paper demonstrates the application of Energy Environmental Sustainability Indicators (EESIs) as part of the developed tool, which assists with the identification of the environmental consequences of energy generation and use scenarios and thereby promotes sustainability, since environmental considerations can then be integrated into the preparation and adoption of policies, plans, programs and projects. Recommendations are made to refine the tool further for South Africa.
Abstract: This paper presents the results of the authors in designing, experimenting, assessing and transferring an innovative approach to energy education in secondary schools, aimed to enhance the quality of learning in terms of didactic curricula and pedagogic methods. The training is online delivered to youngsters via e-Books and portals specially designed for this purpose or by learning by doing via interactive games. An online educational methodology is available teachers.
Abstract: Plants are commonly known for its positive
correlation in reducing temperature. Since it can benefit buildings by
modifying the microclimate, it-s also believed capable of reducing
the internal temperature. Various experiments have been done in
Universiti Sains Malaysia, Penang to investigate the comparison in
thermal benefits between two rooms, one being a typical control
room (exposed wall) and the other a biofacade room (plant shaded
wall). The investigations were conducted during non-rainy season for
approximately a month. Climbing plant Psophocarpus
tetrogonobulus from legume species was selected as insulation for
the biofacade wall. Conclusions were made on whether the biofacade
can be used to tackle the energy efficiency, based on the parameters
taken into consideration.
Abstract: Nuclear energy sources have been widely used in the
past decades in order to power spacecraft subsystems. Nevertheless,
their use has attracted controversy because of the risk of harmful
material released into the atmosphere if an accident were to occur
during the launch phase of the mission, leading to the general
adoption of photovoltaic systems.
As compared to solar cells, wind turbines have a great advantage
on Mars, as they can continuously produce power both during dust
storms and at night-time: this paper focuses on the potential of a wind
energy conversion system (WECS) considering the atmospheric
conditions on Mars. Wind potential on Martian surface has been
estimated, as well as the average energy requirements of a Martian
probe or surface rover. Finally, the expected daily energy output of
the WECS has been computed on the basis of both the swept area of
the rotor and the equivalent wind speed at the landing site.
Abstract: This work presents an approach for the measurement
of mutual inductance on near field inductive coupling. The mutual
inductance between inductive circuits allows the simulation of energy
transfer from reader to tag, that can be used in RFID and powerless
implantable devices. It also allows one to predict the maximum
voltage in the tag of the radio-frequency system.
Abstract: The wireless sensor networks have been extensively
deployed and researched. One of the major issues in wireless sensor
networks is a developing energy-efficient clustering protocol.
Clustering algorithm provides an effective way to prolong the lifetime
of a wireless sensor networks. In the paper, we compare several
clustering protocols which significantly affect a balancing of energy
consumption. And we propose an Energy-Efficient Distributed
Unequal Clustering (EEDUC) algorithm which provides a new way of
creating distributed clusters. In EEDUC, each sensor node sets the
waiting time. This waiting time is considered as a function of residual
energy, number of neighborhood nodes. EEDUC uses waiting time to
distribute cluster heads. We also propose an unequal clustering
mechanism to solve the hot-spot problem. Simulation results show that
EEDUC distributes the cluster heads, balances the energy
consumption well among the cluster heads and increases the network
lifetime.
Abstract: Cosmic showers, during the transit through space, produce
sub - products as a result of interactions with the intergalactic
or interstellar medium which after entering earth generate secondary
particles called Extensive Air Shower (EAS). Detection and analysis
of High Energy Particle Showers involve a plethora of theoretical and
experimental works with a host of constraints resulting in inaccuracies
in measurements. Therefore, there exist a necessity to develop a
readily available system based on soft-computational approaches
which can be used for EAS analysis. This is due to the fact that soft
computational tools such as Artificial Neural Network (ANN)s can be
trained as classifiers to adapt and learn the surrounding variations. But
single classifiers fail to reach optimality of decision making in many
situations for which Multiple Classifier System (MCS) are preferred
to enhance the ability of the system to make decisions adjusting
to finer variations. This work describes the formation of an MCS
using Multi Layer Perceptron (MLP), Recurrent Neural Network
(RNN) and Probabilistic Neural Network (PNN) with data inputs
from correlation mapping Self Organizing Map (SOM) blocks and
the output optimized by another SOM. The results show that the setup
can be adopted for real time practical applications for prediction
of primary energy and location of EAS from density values captured
using detectors in a circular grid.
Abstract: Wireless Sensor networks have a wide spectrum of civil and military applications that call for secure communication such as the terrorist tracking, target surveillance in hostile environments. For the secure communication in these application areas, we propose a method for generating a hierarchical key structure for the efficient group key management. In this paper, we apply A* algorithm in generating a hierarchical key structure by considering the history data of the ratio of addition and eviction of sensor nodes in a location where sensor nodes are deployed. Thus generated key tree structure provides an efficient way of managing the group key in terms of energy consumption when addition and eviction event occurs. A* algorithm tries to minimize the number of messages needed for group key management by the history data. The experimentation with the tree shows efficiency of the proposed method.
Abstract: This paper describes the experimental efficiency of a
compact organic Rankine cycle (ORC) system with a compact
rotary-vane-type expander. The compact ORC system can be used for
power generation from low-temperature heat sources such as waste
heat from various small-scale heat engines, fuel cells, electric devices,
and solar thermal energy. The purpose of this study is to develop an
ORC system with a low power output of less than 1 kW with a hot
temperature source ranging from 60°C to 100°C and a cold
temperature source ranging from 10°C to 30°C. The power output of
the system is rather less due to limited heat efficiency. Therefore, the
system should have an economically optimal efficiency. In order to
realize such a system, an efficient and low-cost expander is
indispensable. An experimental ORC system was developed using the
rotary-vane-type expander which is one of possible candidates of the
expander. The experimental results revealed the expander
performance for various rotation speeds, expander efficiencies, and
thermal efficiencies. Approximately 30 W of expander power output
with 48% expander efficiency and 4% thermal efficiency with a
temperature difference between the hot and cold sources of 80°C was
achieved.
Abstract: The special and unique advantages of explosive
forming, has developed its use in different industries. Considering the
important influence of improving the current explosive forming
techniques on increasing the efficiency and control over the
explosive forming procedure, the effects of air and water as the
energy-conveying medium, and also their differences will be
illustrated in this paper. Hence, a large number of explosive forming
tests have been conducted on two sizes of thin walled cylindrical
shells by using air and water as the working medium. Comparative
diagrams of the maximum radial deflection of work-pieces of the
same size, as a function of the scaled distance, show that for the
points with the same values of scaled distance, the maximum radial
deformation caused by the under water explosive loading is 4 to 5
times more than the deflection of the shells under explosive forming,
while using air. Results of this experimental research have also been
compared with other studies which show that using water as the
energy conveying media increases the efficiency up to 4.8 times. The
effect of the media on failure modes of the shells, and the necking
mechanism of the walls of the specimens, while being explosively
loaded, are also discussed in this issue. Measuring the tested
specimens shows that, the increase in the internal volume has been
accompanied by necking of the walls, which finally results in the
radial rupture of the structure.
Abstract: Natural ventilation is an important means to improve indoor thermal comfort and reduce the energy consumption. A solar chimney system is an enhancing natural draft device, which uses solar radiation to heat the air inside the chimney, thereby converting the thermal energy into kinetic energy. The present study considered some parameters such as chimney width and solar intensity, which were believed to have a significant effect on space ventilation. Fluent CFD software was used to predict buoyant air flow and flow rates in the cavities. The results were compared with available published experimental and theoretical data from the literature. There was an acceptable trend match between the present results and the published data for the room air change per hour, ACH. Further, it was noticed that the solar intensity has a more significant effect on ACH.
Abstract: The rapidly increasing costs of power line extensions
and fossil fuel, combined with the desire to reduce carbon dioxide
emissions pushed the development of hybrid power system suited for
remote locations, the purpose in mind being that of autonomous local
power systems. The paper presents the suggested solution for a “high
penetration" hybrid power system, it being determined by the
location of the settlement and its “zero policy" on carbon dioxide
emissions. The paper focuses on the technical solution and the power
flow management algorithm of the system, taking into consideration
local conditions of development.
Abstract: Renewable energy sources have gained ultimate urgency due to the need of the preservation of the environment for a sustainable development. Pyrolysis is an ultimate promising process in the recycling and acquisition of precious chemicals from wastes. Here, the co-pyrolysis of hazelnut shell with ultra-high molecular weight polyethylene was carried out catalytically and noncatalytically at 500 and 650 ºC. Potassium dichromate was added in certain amounts to act as a catalyst. The liquid, solid and gas products quantities were determined by gravimetry. As a main result, remarkable increases in gasification were observed by using this catalyst for pure components and their blends especially at 650 ºC. The increase in gas product quantity was compensated mainly with the decreases in the solid products and additionally in some cases liquid products quantities. These observations may stem from mainly the activation of carbon-carbon bonds rather than carbon-hydrogen bonds via potassium dichromate. Also, the catalytic effect of potassium dichromate on HS: PEO and HS: UHMWPE co-pyrolysis was compared.
Abstract: During recent years, attention in 'Green Computing'
has moved research into energy-saving techniques for home
computers to enterprise systems' Client and Server machines. Saving
energy or reduction of carbon footprints is one of the aspects of
Green Computing. The research in the direction of Green Computing
is more than just saving energy and reducing carbon foot prints. This
study provides a brief account of Green Computing. The emphasis of
this study is on current trends in Green Computing; challenges in the
field of Green Computing and the future trends of Green Computing.
Abstract: Delamination between layers in composite materials is a major structural failure. The delamination resistance is quantified by the critical strain energy release rate (SERR). The present investigation deals with the strain energy release rate of two woven fabric composites. Materials used are made of two types of glass fiber (360 gsm and 600 gsm) of plain weave and epoxy as matrix. The fracture behavior is studied using the mode I, double cantilever beam test and the mode II, end notched flexure test, in order to determine the energy required for the initiation and growth of an artificial crack. The delamination energy of these two materials is compared in order to study the effect of weave and reinforcement on mechanical properties. The fracture mechanism is also analyzed by means of scanning electron microscopy (SEM). It is observed that the plain weave fabric composite with lesser strand width has higher inter laminar fracture properties compared to the plain weave fabric composite with more strand width.
Abstract: In this paper, we consider a multi user multiple input
multiple output (MU-MIMO) based cooperative reporting system for
cognitive radio network. In the reporting network, the secondary
users forward the primary user data to the common fusion center
(FC). The FC is equipped with linear equalizers and an energy
detector to make the decision about the spectrum. The primary user
data are considered to be a digital video broadcasting - terrestrial
(DVB-T) signal. The sensing channel and the reporting channel are
assumed to be an additive white Gaussian noise and an independent
identically distributed Raleigh fading respectively. We analyzed the
detection probability of MU-MIMO system with linear equalizers and
arrived at the closed form expression for average detection
probability. Also the system performance is investigated under
various MIMO scenarios through Monte Carlo simulations.
Abstract: In this paper, a theoretical formula is presented to
predict the instantaneous folding force of the first fold creation in a
square column under axial loading. Calculations are based on analysis
of “Basic Folding Mechanism" introduced by Wierzbicki and
Abramowicz. For this purpose, the sum of dissipated energy rate under
bending around horizontal and inclined hinge lines and dissipated
energy rate under extensional deformations are equated to the work rate
of the external force on the structure. Final formula obtained in this
research, reasonably predicts the instantaneous folding force of the first
fold creation versus folding distance and folding angle and also predicts
the instantaneous folding force instead of the average value. Finally,
according to the calculated theoretical relation, instantaneous folding
force of the first fold creation in a square column was sketched
versus folding distance and was compared to the experimental results
which showed a good correlation.