Abstract: This paper evaluate the multilevel modulation for
different techniques such as amplitude shift keying (M-ASK), MASK,
differential phase shift keying (M-ASK-Bipolar), Quaternary
Amplitude Shift Keying (QASK) and Quaternary Polarization-ASK
(QPol-ASK) at a total bit rate of 107 Gbps. The aim is to find a costeffective
very high speed transport solution. Numerical investigation
was performed using Monte Carlo simulations. The obtained results
indicate that some modulation formats can be operated at 100Gbps
in optical communication systems with low implementation effort
and high spectral efficiency.
Abstract: In this paper, the robust exponential stability problem of discrete-time uncertain stochastic neural networks with timevarying delays is investigated. By introducing a new augmented Lyapunov function, some delay-dependent stable results are obtained in terms of linear matrix inequality (LMI) technique. Compared with some existing results in the literature, the conservatism of the new criteria is reduced notably. Three numerical examples are provided to demonstrate the less conservatism and effectiveness of the proposed method.
Abstract: Three-dimensional simulation of harmonic up
generation in free electron laser amplifier operating simultaneously
with a cold and relativistic electron beam is presented in steady-state
regime where the slippage of the electromagnetic wave with respect
to the electron beam is ignored. By using slowly varying envelope
approximation and applying the source-dependent expansion to wave
equations, electromagnetic fields are represented in terms of the
Hermit Gaussian modes which are well suited for the planar wiggler
configuration. The electron dynamics is described by the fully threedimensional
Lorentz force equation in presence of the realistic planar
magnetostatic wiggler and electromagnetic fields. A set of coupled
nonlinear first-order differential equations is derived and solved
numerically. The fundamental and third harmonic radiation of the
beam is considered. In addition to uniform beam, prebunched
electron beam has also been studied. For this effect of sinusoidal
distribution of entry times for the electron beam on the evolution of
radiation is compared with uniform distribution. It is shown that
prebunching reduces the saturation length substantially. For
efficiency enhancement the wiggler is set to decrease linearly when
the radiation of the third harmonic saturates. The optimum starting
point of tapering and the slope of radiation in the amplitude of
wiggler are found by successive run of the code.
Abstract: A mathematical model for the hydrodynamic
lubrication of parabolic slider bearings with couple stress lubricants
is presented. A numerical solution for the mathematical model using
finite element scheme is obtained using three nodes isoparametric
quadratic elements. Stiffness integrals obtained from the weak form
of the governing equations were solved using Gauss Quadrature to
obtain a finite number of stiffness matrices. The global system of
equations was obtained for the bearing and solved using Gauss Seidel
iterative scheme. The converged pressure solution was used to obtain
the load capacity of the bearing. Parametric studies were carried out
and it was shown that the effect of couple stresses and profile
parameter are to increase the load carrying capacity of the parabolic
slider bearing. Numerical experiments reveal that the magnitude of
the profile parameter at which maximum load is obtained increases
with decrease in couple stress parameter. The results are presented in
graphical form.
Abstract: In this paper, the differential quadrature method is applied to simulate natural convection in an inclined cubic cavity using velocity-vorticity formulation. The numerical capability of the present algorithm is demonstrated by application to natural convection in an inclined cubic cavity. The velocity Poisson equations, the vorticity transport equations and the energy equation are all solved as a coupled system of equations for the seven field variables consisting of three velocities, three vorticities and temperature. The coupled equations are simultaneously solved by imposing the vorticity definition at boundary without requiring the explicit specification of the vorticity boundary conditions. Test results obtained for an inclined cubic cavity with different angle of inclinations for Rayleigh number equal to 103, 104, 105 and 106 indicate that the present coupled solution algorithm could predict the benchmark results for temperature and flow fields. Thus, it is convinced that the present formulation is capable of solving coupled Navier-Stokes equations effectively and accurately.
Abstract: This paper discusses a design of nonlinear observer by
a formal linearization method using an application of Chebyshev Interpolation
in order to facilitate processes for synthesizing a nonlinear
observer and to improve the precision of linearization.
A dynamic nonlinear system is linearized with respect to a linearization
function, and a measurement equation is transformed into
an augmented linear one by the formal linearization method which is
based on Chebyshev interpolation. To the linearized system, a linear
estimation theory is applied and a nonlinear observer is derived. To
show effectiveness of the observer design, numerical experiments
are illustrated and they indicate that the design shows remarkable
performances for nonlinear systems.
Abstract: The Swine flu outbreak in humans is due to a new
strain of influenza A virus subtype H1N1 that derives in part from
human influenza, avian influenza, and two separated strains of swine
influenza. It can be transmitted from human to human. A
mathematical model for the transmission of Swine flu is developed in
which the human populations are divided into two classes, the risk
and non-risk human classes. Each class is separated into susceptible,
exposed, infectious, quarantine and recovered sub-classes. In this
paper, we formulate the dynamical model of Swine flu transmission
and the repetitive contacts between the people are also considered.
We analyze the behavior for the transmission of this disease. The
Threshold condition of this disease is found and numerical results are
shown to confirm our theoretical predictions.
Abstract: This paper describes a one-dimensional numerical model for natural gas production from the dissociation of methane hydrate in hydrate-capped gas reservoir under depressurization and thermal stimulation. Some of the hydrate reservoirs discovered are overlying a free-gas layer, known as hydrate-capped gas reservoirs. These reservoirs are thought to be easiest and probably the first type of hydrate reservoirs to be produced. The mathematical equations that can be described this type of reservoir include mass balance, heat balance and kinetics of hydrate decomposition. These non-linear partial differential equations are solved using finite-difference fully implicit scheme. In the model, the effect of convection and conduction heat transfer, variation change of formation porosity, the effect of using different equations of state such as PR and ER and steam or hot water injection are considered. In addition distributions of pressure, temperature, saturation of gas, hydrate and water in the reservoir are evaluated. It is shown that the gas production rate is a sensitive function of well pressure.
Abstract: This paper aims to establish a delayed dynamical relationship between payoffs of players in a zero-sum game. By introducing Markovian chain and time delay in the network model, a delayed game network model with sector bounds and slope bounds restriction nonlinear function is first proposed. As a result, a direct dynamical relationship between payoffs of players in a zero-sum game can be illustrated through a delayed singular system. Combined with Finsler-s Lemma and Lyapunov stable theory, a sufficient condition guaranteeing the unique existence and stability of zero-sum game-s Nash equilibrium is derived. One numerical example is presented to illustrate the validity of the main result.
Abstract: In the present paper, a numerical investigation has
been carried out to classify and clarify the effects of paramount
parameters on turbulent impinging slot jets. The effects of nozzle-s
exit turbulent intensity, distance between nozzle and impinging plate
are studied at Reynolds number 5000 and 20000. In addition, the
effect of Mach number that is varied between 0.3-0.8 at a constant
Reynolds number 133000 is investigated to elucidate the effect of
compressibility in impinging jet upon a flat plate. The wall that is
located at the same level with nozzle-s exit confines the flow. A
compressible finite volume solver is implemented for simulation the
flow behavior. One equation Spalart-Allmaras turbulent model is
used to simulate turbulent flow at this study. Assessment of the
Spalart-Allmaras turbulent model at high nozzle to plate distance,
and giving enough insights to characterize the effect of Mach number
at high Reynolds number for the complex impinging jet flow are the
remarkable results of this study.
Abstract: Prediction of benzene transport in soil and volatilization from soil to the atmosphere is important for the preservation of human health and management of contaminated soils. The adequacy of a simple numerical model, assuming two-phase diffusion and equilibrium of liquid/solid adsorption, was investigated by experimental data of benzene concentration in a flux chamber (with headspace) where Andosol and sand were filled. Adsorption experiment for liquid phase was performed to determine an adsorption coefficient. Furthermore, adequacy of vapor phase adsorption was also studied through two runs of experiment using sand with different water content. The results show that the model adequately predicted benzene transport and volatilization from Andosol and sand with water content of 14.0%. In addition, the experiment additionally revealed that vapor phase adsorption should be considered in diffusion model for sand with very low water content.
Abstract: Resistance spot welding process comprises of electric,
thermal and mechanical phenomenon, which makes this process
complex and highly non-linear and thus, it becomes difficult to model
it. In order to obtain good weld nugget during spot welding, hit and
trial welds are usually done which is very costly. Therefore the
numerical simulation research has been conducted to understand the
whole process. In this paper three different cases were analyzed by
varying the tip contact area and it was observed that, with the
variation of tip contact area the nugget formation at the faying
surface is affected. The tip contact area of the welding electrode
becomes large with long welding cycles. Therefore in order to
maintain consistency of nugget formation during the welding process,
the current compensation in control feedback is required. If the
contact area of the welding electrode tip is reduced, a large amount of
current flows through the faying surface, as a result of which
sputtering occurs.
Abstract: In this paper, the local grid refinement is focused by
using a nested grid technique. The Cartesian grid numerical method is
developed for simulating unsteady, viscous, incompressible flows
with complex immersed boundaries. A finite volume method is used in
conjunction with a two-step fractional-step procedure. The key aspects
that need to be considered in developing such a nested grid solver are
imposition of interface conditions on the inter-block and accurate
discretization of the governing equation in cells that are with the
inter-block as a control surface. A new interpolation procedure is
presented which allows systematic development of a spatial
discretization scheme that preserves the spatial accuracy of the
underlying solver. The present nested grid method has been tested by
two numerical examples to examine its performance in the two
dimensional problems. The numerical examples include flow past a
circular cylinder symmetrically installed in a Channel and flow past
two circular cylinders with different diameters. From the numerical
experiments, the ability of the solver to simulate flows with
complicated immersed boundaries is demonstrated and the nested grid
approach can efficiently speed up the numerical solutions.
Abstract: Plasma Wind Tunnels (PWT) are extensively used for screening and qualification of re-entry Thermel Protection System (TPS) materials. Proper design of a supersonic diffuser for plasma wind tunnel is of importance for achieving good pressurerecovery (thereby reducing vacuum pumping requirement & run time costs) and isolating downstream stream fluctuations from propagating costs) and isolating downstream stream fluctuationnts the details of a rapid design methodology successfully employed for designing supersonic diffuser for high power (several megawatts)plasma wind tunnels and numerical performance analysis of a diffuser configuration designed for one megawatt power rated plasma wind tunnel(enthalpy ~ 30 MJ/kg) using FLUENT 6.3® solver for different diffuser operating sub-atmospheric back-pressures.
Abstract: Following harvest, fresh produce needs to be cooled
immediately in a room where the air temperature and the relative air
humidity are controlled to maintain the produce quality. In this paper,
an experimental study for forced air cooling of fresh produce
(cauliflower) is performed using a pilot developed within our
laboratory. Furthermore, a numerical simulation of spherical
produces, taking into account the aerodynamic aspect and also the
heat transfer in the produce and in the air, was carried out using a
finite element method. At the end of this communication,
experimental results are presented and compared with the simulation.
Abstract: Natural gas flow contains undesirable solid particles,
liquid condensation, and/or oil droplets and requires reliable
removing equipment to perform filtration. Recent natural gas
processing applications are demanded compactness and reliability of
process equipment. Since conventional means are sophisticated in
design, poor in efficiency, and continue lacking robust, a supersonic
nozzle has been introduced as an alternative means to meet such
demands.
A 3-D Convergent-Divergent Nozzle is simulated using
commercial Code for pressure ratio (NPR) varies from 1.2 to 2. Six
different shapes of nozzle are numerically examined to illustrate the
position of shock-wave as such spot could be considered as a
benchmark of particle separation. Rectangle, triangle, circular,
elliptical, pentagon, and hexagon nozzles are simulated using Fluent
Code with all have same cross-sectional area.
The simple one-dimensional inviscid theory does not describe the
actual features of fluid flow precisely as it ignores the impact of
nozzle configuration on the flow properties. CFD Simulation results,
however, show that nozzle geometry influences the flow structures
including location of shock wave.
The CFD analysis predicts shock appearance when p01/pa>1.2 for
almost all geometry and locates at the lower area ratio (Ae/At).
Simulation results showed that shock wave in Elliptical nozzle has
the farthest distance from the throat among the others at relatively
small NPR. As NPR increases, hexagon would be the farthest. The
numerical result is compared with available experimental data and
has shown good agreement in terms of shock location and flow
structure.
Abstract: In the present study, a steady-state simulation model
has been developed to evaluate the system performance of a
transcritical carbon dioxide heat pump system for simultaneous water
cooling and heating. Both the evaporator (including both two-phase
and superheated zone) and gas cooler models consider the highly
variable heat transfer characteristics of CO2 and pressure drop. The
numerical simulation model of transcritical CO2 heat pump has been
validated by test data obtained from experiments on the heat pump
prototype. Comparison between the test results and the model
prediction for system COP variation with compressor discharge
pressure shows a modest agreement with a maximum deviation of
15% and the trends are fairly similar. Comparison for other operating
parameters also shows fairly similar deviation between the test
results and the model prediction. Finally, the simulation results are
presented to study the effects of operating parameters such as,
temperature of heat exchanger fluid at the inlet, discharge pressure,
compressor speed on system performance of CO2 heat pump, suitable
in a dairy plant where simultaneous cooling at 4oC and heating at
73oC are required. Results show that good heat transfer properties of
CO2 for both two-phase and supercritical region and efficient
compression process contribute a lot for high system COPs.
Abstract: A parallel computational fluid dynamics code has been
developed for the study of aerodynamic heating problem in hypersonic
flows. The code employs the 3D Navier-Stokes equations as the basic
governing equations to simulate the laminar hypersonic flow. The cell
centered finite volume method based on structured grid is applied for
spatial discretization. The AUSMPW+ scheme is used for the inviscid
fluxes, and the MUSCL approach is used for higher order spatial
accuracy. The implicit LU-SGS scheme is applied for time integration
to accelerate the convergence of computations in steady flows. A
parallel programming method based on MPI is employed to shorten
the computing time. The validity of the code is demonstrated by
comparing the numerical calculation result with the experimental data
of a hypersonic flow field around a blunt body.
Abstract: In this research work, investigations are carried out on
Continuous Wave (CW) Nd:YAG laser welding system after
preliminary experimentation to understand the influencing parameters
associated with laser welding of AISI 304. The experimental
procedure involves a series of laser welding trials on AISI 304
stainless steel sheets with various combinations of process parameters
like beam power, beam incident angle and beam incident angle. An
industrial 2 kW CW Nd:YAG laser system, available at Welding
Research Institute (WRI), BHEL Tiruchirappalli, is used for
conducting the welding trials for this research. After proper tuning of
laser beam, laser welding experiments are conducted on AISI 304
grade sheets to evaluate the influence of various input parameters on
weld bead geometry i.e. bead width (BW) and depth of penetration
(DOP). From the laser welding results, it is noticed that the beam
power and welding speed are the two influencing parameters on
depth and width of the bead. Three dimensional finite element
simulation of high density heat source have been performed for laser
welding technique using finite element code ANSYS for predicting
the temperature profile of laser beam heat source on AISI 304
stainless steel sheets. The temperature dependent material properties
for AISI 304 stainless steel are taken into account in the simulation,
which has a great influence in computing the temperature profiles.
The latent heat of fusion is considered by the thermal enthalpy of
material for calculation of phase transition problem. A Gaussian
distribution of heat flux using a moving heat source with a conical
shape is used for analyzing the temperature profiles. Experimental
and simulated values for weld bead profiles are analyzed for stainless
steel material for different beam power, welding speed and beam
incident angle. The results obtained from the simulation are
compared with those from the experimental data and it is observed
that the results of numerical analysis (FEM) are in good agreement
with experimental results, with an overall percentage of error
estimated to be within ±6%.
Abstract: Laser Profiler (LP) data from aerial laser surveys have
been increasingly used as topographical inputs to numerical
simulations of flooding and inundation in river basins. LP data has
great potential for reproducing topography, but its effective usage has
not yet been fully established. In this study, flooding and inundation
are simulated numerically using LP data for the Jobaru River basin of
Japan’s Saga Plain. The analysis shows that the topography is
reproduced satisfactorily in the computational domain with urban and
agricultural areas requiring different grid sizes. A 2-D numerical
simulation shows that flood flow behavior changes as grid size is
varied.