Abstract: Saturated hydraulic conductivity is one of the soil
hydraulic properties which is widely used in environmental studies
especially subsurface ground water. Since, its direct measurement is
time consuming and therefore costly, indirect methods such as
pedotransfer functions have been developed based on multiple linear
regression equations and neural networks model in order to estimate
saturated hydraulic conductivity from readily available soil
properties e.g. sand, silt, and clay contents, bulk density, and organic
matter. The objective of this study was to develop neural networks
(NNs) model to estimate saturated hydraulic conductivity from
available parameters such as sand and clay contents, bulk density,
van Genuchten retention model parameters (i.e. r
θ , α , and n) as well
as effective porosity. We used two methods to calculate effective
porosity: : (1) eff s FC φ =θ -θ , and (2) inf φ =θ -θ eff s , in which s
θ is
saturated water content, FC θ is water content retained at -33 kPa
matric potential, and inf θ is water content at the inflection point.
Total of 311 soil samples from the UNSODA database was divided
into three groups as 187 for the training, 62 for the validation (to
avoid over training), and 62 for the test of NNs model. A commercial
neural network toolbox of MATLAB software with a multi-layer
perceptron model and back propagation algorithm were used for the
training procedure. The statistical parameters such as correlation
coefficient (R2), and mean square error (MSE) were also used to
evaluate the developed NNs model. The best number of neurons in
the middle layer of NNs model for methods (1) and (2) were
calculated 44 and 6, respectively. The R2 and MSE values of the test
phase were determined for method (1), 0.94 and 0.0016, and for
method (2), 0.98 and 0.00065, respectively, which shows that method
(2) estimates saturated hydraulic conductivity better than method (1).
Abstract: Many multimedia communication applications require a
source to transmit messages to multiple destinations subject to quality
of service (QoS) delay constraint. To support delay constrained
multicast communications, computer networks need to guarantee an
upper bound end-to-end delay from the source node to each of
the destination nodes. This is known as multicast delay problem.
On the other hand, if the same message fails to arrive at each
destination node at the same time, there may arise inconsistency and
unfairness problem among users. This is related to multicast delayvariation
problem. The problem to find a minimum cost multicast
tree with delay and delay-variation constraints has been proven to
be NP-Complete. In this paper, we propose an efficient heuristic
algorithm, namely, Economic Delay and Delay-Variation Bounded
Multicast (EDVBM) algorithm, based on a novel heuristic function,
to construct an economic delay and delay-variation bounded multicast
tree. A noteworthy feature of this algorithm is that it has very high
probability of finding the optimal solution in polynomial time with
low computational complexity.
Abstract: In this paper, Economic Order Quantity (EOQ) based model for non-instantaneous Weibull distribution deteriorating items with power demand pattern is presented. In this model, the holding cost per unit of the item per unit time is assumed to be an increasing linear function of time spent in storage. Here the retailer is allowed a trade-credit offer by the supplier to buy more items. Also in this model, shortages are allowed and partially backlogged. The backlogging rate is dependent on the waiting time for the next replenishment. This model aids in minimizing the total inventory cost by finding the optimal time interval and finding the optimal order quantity. The optimal solution of the model is illustrated with the help of numerical examples. Finally sensitivity analysis and graphical representations are given to demonstrate the model.
Abstract: Defense and Aerospace environment is continuously
striving to keep up with increasingly sophisticated Information
Technology (IT) in order to remain effective in today-s dynamic and
unpredictable threat environment. This makes IT one of the largest
and fastest growing expenses of Defense. Hundreds of millions of
dollars spent a year on IT projects. But, too many of those millions
are wasted on costly mistakes. Systems that do not work properly,
new components that are not compatible with old ones, trendy new
applications that do not really satisfy defense needs or lost through
poorly managed contracts.
This paper investigates and compiles the effective strategies that
aim to end exasperation with low returns and high cost of
Information Technology acquisition for defense; it tries to show how
to maximize value while reducing time and expenditure.
Abstract: Medicinal plants are most suitable crops for ecological production systems because of their role in human health and the aim of sustainable agriculture to improve ecosystem efficiency and its products quality. Calculations include energy output (contents of energy in seed) and energy inputs (consumption of fertilizers, pesticides, labor, machines, fuel and electricity). The ratio of output of the production to inputs is called the energy outputs / inputs ratio or energy efficiency. One way to quantify essential parts of agricultural development is the energy flow method. The output / input energy ratio is proposed as the most comprehensive single factor in pursuing the objective of sustainability. Sylibum marianum L. is one of the most important medicinal plants in Iran and has effective role on health of growing population in Iran. The objective of this investigation was to find out energy efficiency in conventional and low input production system of Milk thistle. This investigation was carried out in the spring of 2005 – 2007 in the Research Station of Rangelands in Hamand - Damavand region of IRAN. This experiment was done in split-split plot based on randomized complete block design with 3 replications. Treatments were 2 production systems (Conventional and Low input system) in the main plots, 3 planting time (25 of March, 4 and 14 of April) in the sub plots and 2 seed types (Improved and Native of Khoozestan) in the sub-sub plots. Results showed that in conventional production system energy efficiency, because of higher inputs and less seed yield, was less than low input production system. Seed yield was 1199.5 and 1888 kg/ha in conventional and low input systems, respectively. Total energy inputs and out puts for conventional system was 10068544.5 and 7060515.9 kcal. These amounts for low input system were 9533885.6 and 11113191.8 kcal. Results showed that energy efficiency for seed production in conventional and low input system was 0.7 and 1.16, respectively. So, milk thistle seed production in low input system has 39.6 percent higher energy efficiency than conventional production system. Also, higher energy efficiency were found in sooner planting time (25 of March) and native seed of Khoozestan.
Abstract: The genetic algorithm (GA) based solution techniques
are found suitable for optimization because of their ability of
simultaneous multidimensional search. Many GA-variants have been
tried in the past to solve optimal power flow (OPF), one of the
nonlinear problems of electric power system. The issues like
convergence speed and accuracy of the optimal solution obtained
after number of generations using GA techniques and handling
system constraints in OPF are subjects of discussion. The results
obtained for GA-Fuzzy OPF on various power systems have shown
faster convergence and lesser generation costs as compared to other
approaches. This paper presents an enhanced GA-Fuzzy OPF (EGAOPF)
using penalty factors to handle line flow constraints and load
bus voltage limits for both normal network and contingency case
with congestion. In addition to crossover and mutation rate
adaptation scheme that adapts crossover and mutation probabilities
for each generation based on fitness values of previous generations, a
block swap operator is also incorporated in proposed EGA-OPF. The
line flow limits and load bus voltage magnitude limits are handled by
incorporating line overflow and load voltage penalty factors
respectively in each chromosome fitness function. The effects of
different penalty factors settings are also analyzed under contingent
state.
Abstract: This paper introduces a mixed integer programming model to find the optimum development plan for port Anzali. The model minimizes total system costs taking into account both port infrastructure costs and shipping costs. Due to the multipurpose function of the port, the model consists of 1020 decision variables and 2490 constraints. Results of the model determine the optimum number of berths that should be constructed in each period and for each type of cargo. In addition to, the results of sensitivity analysis on port operation quantity provide useful information for managers to choose the best scenario for port planning with the lowest investment risks. Despite all limitations-due to data availability-the model offers a straightforward decision tools to port planners aspiring to achieve optimum port planning steps.
Abstract: In the past few years, the use of wireless sensor networks (WSNs) potentially increased in applications such as intrusion detection, forest fire detection, disaster management and battle field. Sensor nodes are generally battery operated low cost devices. The key challenge in the design and operation of WSNs is to prolong the network life time by reducing the energy consumption among sensor nodes. Node clustering is one of the most promising techniques for energy conservation. This paper presents a novel clustering algorithm which maximizes the network lifetime by reducing the number of communication among sensor nodes. This approach also includes new distributed cluster formation technique that enables self-organization of large number of nodes, algorithm for maintaining constant number of clusters by prior selection of cluster head and rotating the role of cluster head to evenly distribute the energy load among all sensor nodes.
Abstract: For about two decades scientists have been
developing techniques for enhancing the quality of medical images
using Fourier transform, DWT (Discrete wavelet transform),PDE
model etc., Gabor wavelet on hexagonal sampled grid of the images
is proposed in this work. This method has optimal approximation
theoretic performances, for a good quality image. The computational
cost is considerably low when compared to similar processing in the
rectangular domain. As X-ray images contain light scattered pixels,
instead of unique sigma, the parameter sigma of 0.5 to 3 is found to
satisfy most of the image interpolation requirements in terms of high
Peak Signal-to-Noise Ratio (PSNR) , lower Mean Squared Error
(MSE) and better image quality by adopting windowing technique.
Abstract: In the last decade, carbohydrates have attracted great
attention as renewable resources for the chemical industry.
Carbohydrates are abundantly found in nature in the form of
monomers, oligomers and polymers, or as components of
biopolymers and other naturally occurring substances. As natural
products, they play important roles in conferring certain physical,
chemical, and biological properties to their carrier molecules.The
synthesis of this particular carbohydrate glycomonomer is part of our
work to obtain biodegradable polymers. Our current paper describes
the synthesis and characterization of a novel carbohydrate
glycomonomer starting from D-glucose, in several synthesis steps,
that involve the protection/deprotection of the D-glucose ring via
acetylation, tritylation, then selective deprotection of the aromaticaliphatic
protective group, in order to obtain 1,2,3,4-tetra-O-acetyl-
6-O-allyl-β-D-glucopyranose. The glycomonomer was then obtained
by the allylation in drastic conditions of 1,2,3,4-tetra-O-acetyl-6-Oallyl-
β-D-glucopyranose with allylic alcohol in the presence of
stannic chloride, in methylene chloride, at room temperature. The
proposed structure of the glycomonomer, 2,3,4-tri-O-acetyl-1,6-di-
O-allyl-β-D-glucopyranose, was confirmed by FTIR, NMR and
HPLC-MS spectrometry. This glycomonomer will be further
submitted to copolymerization with certain acrylic or methacrylic
monomers in order to obtain competitive plastic materials for
applications in the biomedical field.
Abstract: The aim of our research was to evaluate the effects of
physical exercise on lipid profile and anthropometric characteristics
in young subjects, diagnosed with metabolic syndrome (MS). The
study has been developed during 28 weeks on 20 young obese
patients which have undertaken an intermittent submaximal exercise
program. After 28 weeks of physical activity, the results show
significant effects on anthropometric characteristics and serum lipid
profile of research subjects. Additionally, the results of this study
confirms the major correlation between the variations of
intraabdominal adiposity, determined ultrasonographycally,
and the changes of serum lipid concentrations, a better
correlation than it is used abdominal circumference or body
weight index.
Abstract: Bubble columns have a variety of applications in
absorption, bio-reactions, catalytic slurry reactions, and coal
liquefaction; because they are simple to operate, provide good heat
and mass transfer, having less operational cost. The use of
Computational Fluid Dynamics (CFD) for bubble column becomes
important, since it can describe the fluid hydrodynamics on both local
and global scale. Euler- Euler two-phase fluid model has been used to
simulate two-phase (air and water) transient up-flow in bubble
column (15cm diameter) using FLUENT6.3. These simulations and
experiments were operated over a range of superficial gas velocities
in the bubbly flow and churn turbulent regime (1 to16 cm/s) at
ambient conditions. Liquid velocity was varied from 0 to 16cm/s. The
turbulence in the liquid phase is described using the standard k-ε
model. The interactions between the two phases are described
through drag coefficient formulations (Schiller Neumann). The
objectives are to validate CFD simulations with experimental data,
and to obtain grid-independent numerical solutions. Quantitatively
good agreements are obtained between experimental data for hold-up
and simulation values. Axial liquid velocity profiles and gas holdup
profiles were also obtained for the simulation.
Abstract: Although lighting systems powered by Photovoltaic
(PV) cells have existed for many years, they are not widely used,
especially in lighting for buildings, due to their high initial cost and
low conversion efficiency. One of the technical challenges facing PV
powered lighting systems has been how to use dc power generated by
the PV module to energize common light sources that are designed to
operate efficiently under ac power. Usually, the efficiency of the dc
light sources is very poor compared to ac light sources. Rapid
developments in LED lighting systems have made this technology a
potential candidate for PV powered lighting systems. This study
analyzed the efficiency of each component of PV powered lighting
systems to identify optimum system configurations for different
applications.
Abstract: This paper describes a newly designed decentralized
nonlinear control strategy to control a robot manipulator. Based on the
concept of the nonlinear state feedback theory and decentralized
concept is developed to improve the drawbacks in previous works
concerned with complicate intelligent control and low cost effective
sensor. The control methodology is derived in the sense of Lyapunov
theorem so that the stability of the control system is guaranteed. The
decentralized algorithm does not require other joint angle and velocity
information. Individual Joint controller is implemented using a digital
processor with nearly actuator to make it possible to achieve good
dynamics and modular. Computer simulation result has been
conducted to validate the effectiveness of the proposed control scheme
under the occurrence of possible uncertainties and different reference
trajectories. The merit of the proposed control system is indicated in
comparison with a classical control system.
Abstract: Gas flaring is one of the most GHG emitting sources in the oil and gas industries. It is also a major way for wasting such an energy that could be better utilized and even generates revenue. Minimize flaring is an effective approach for reducing GHG emissions and also conserving energy in flaring systems. Integrating waste and flared gases into the fuel gas networks (FGN) of refineries is an efficient tool. A fuel gas network collects fuel gases from various source streams and mixes them in an optimal manner, and supplies them to different fuel sinks such as furnaces, boilers, turbines, etc. In this article we use fuel gas network model proposed by Hasan et al. as a base model and modify some of its features and add constraints on emission pollution by gas flaring to reduce GHG emissions as possible. Results for a refinery case study showed that integration of flare gas stream with waste and natural gas streams to construct an optimal FGN can significantly reduce total annualized cost and flaring emissions.
Abstract: This paper presents an analytical model to estimate
the cost of an optimized design of reinforced concrete isolated
footing base on structural safety. Flexural and optimized formulas for
square and rectangular footingare derived base on ACI building code
of design, material cost and optimization. The optimization
constraints consist of upper and lower limits of depth and area of
steel. Footing depth and area of reinforcing steel are to be minimized
to yield the optimal footing dimensions. Optimized footing materials
cost of concrete, reinforcing steel and formwork of the designed
sections are computed. Total cost factor TCF and other cost factors
are developed to generalize and simplify the calculations of footing
material cost. Numerical examples are presented to illustrate the
model capability of estimating the material cost of the footing for a
desired axial load.
Abstract: The myoelectric signal (MES) is one of the Biosignals
utilized in helping humans to control equipments. Recent approaches
in MES classification to control prosthetic devices employing pattern
recognition techniques revealed two problems, first, the classification
performance of the system starts degrading when the number of
motion classes to be classified increases, second, in order to solve the
first problem, additional complicated methods were utilized which
increase the computational cost of a multifunction myoelectric
control system. In an effort to solve these problems and to achieve a
feasible design for real time implementation with high overall
accuracy, this paper presents a new method for feature extraction in
MES recognition systems. The method works by extracting features
using Wavelet Packet Transform (WPT) applied on the MES from
multiple channels, and then employs Fuzzy c-means (FCM)
algorithm to generate a measure that judges on features suitability for
classification. Finally, Principle Component Analysis (PCA) is
utilized to reduce the size of the data before computing the
classification accuracy with a multilayer perceptron neural network.
The proposed system produces powerful classification results (99%
accuracy) by using only a small portion of the original feature set.
Abstract: The determination of sugars in foods is very
significant. Their relation in fact, can affect the chemical and
sensorial quality of the matrix (e.g., sweetness, pH, total acidity,
microbial stability, global acceptability) and can provide information
on food to optimize several selected technological processes. Three
stages of ripeness (green, yellow and red) of tomatoes (Lycopersicon
Esculentum cv. Elegance) at different harvest dates were evaluated.
Fruit from all harvests were exposed to different of ozone doses
(0.25, 0.50 and 1 mg O3/g tomatoes) and clean air for 5 day at 15
°C±2 and 90-95 % relative humidity. Then, fruits were submitted for
extraction and analysis after a day from the finish of exposure of each
stage. The concentrations of the glucose and fructose increased in the
tomatoes which were subjected to ozone treatments.
Abstract: This paper presents Qmulus- a Cloud Based GPS
Model. Qmulus is designed to compute the best possible route which
would lead the driver to the specified destination in the shortest time
while taking into account real-time constraints. Intelligence
incorporated to Qmulus-s design makes it capable of generating and
assigning priorities to a list of optimal routes through customizable
dynamic updates. The goal of this design is to minimize travel and
cost overheads, maintain reliability and consistency, and implement
scalability and flexibility. The model proposed focuses on
reducing the bridge between a Client Application and a Cloud
service so as to render seamless operations. Qmulus-s system
model is closely integrated and its concept has the potential to be
extended into several other integrated applications making it capable
of adapting to different media and resources.
Abstract: This paper presents the influence of distributed generation (DG) on congestion and locational marginal price (LMP) in an optimal power flow (OPF) based wholesale electricity market. The problem of optimal placement to manage congestion and reduce LMP is formulated for the objective of social welfare maximization. From competitive electricity market standpoint, DGs have great value when they reduce load in particular locations and at particular times when feeders are heavily loaded. The paper lies on the groundwork that solution to optimal mix of generation and transmission resources can be achieved by addressing congestion and corresponding LMP. Obtained as lagrangian multiplier associated with active power flow equation for each node, LMP gives the short run marginal cost (SRMC) of electricity. Specific grid locations are examined to study the influence of DG penetration on congestion and corresponding shadow prices. The influence of DG on congestion and locational marginal prices has been demonstrated in a modified IEEE 14 bus test system.