Abstract: The reduction of hexavalent chromium by scrap iron
was investigated in continuous system, using long-term column
experiments, for aqueous Cr(VI) solutions having low buffering
capacities, over the Cr(VI) concentration range of 5 – 40 mg/L. The
results showed that the initial Cr(VI) concentration significantly
affects the reduction capacity of scrap iron. Maximum reduction
capacity of scrap iron was observed at the beginning of the column
experiments; the lower the Cr(VI) concentration, the greater the
experiment duration with maximum scrap iron reduction capacity.
However, due to passivation of active surface, scrap iron reduction
capacity continuously decreased in time, especially after Cr(VI)
breakthrough. The experimental results showed that highest
reduction capacity recorded until Cr(VI) breakthrough was 22.8 mg
Cr(VI)/g scrap iron, at CI = 5 mg/L, and decreased with increasing
Cr(VI) concentration. In order to assure total reduction of greater
Cr(VI) concentrations for a longer period of time, either the mass of
scrap iron filling, or the hydraulic retention time should be increased.
Abstract: The efficient operation of any biological treatment
process requires pre-treatment of incompatible pollutants such as
acids, bases, oil, toxic substances, etc. which hamper the treatment
of other major components which are otherwise degradable. The
pre-treatment of alkaline waste-waters, generated from various
industries like textile, paper & pulp, potato-processing industries,
etc., having a pH of 10 or higher, is essential. The pre-treatment,
i.e., neutralization of such alkaline waste-waters can be achieved by
chemical as well as biological means. However, the biological pretreatment
offers better package over the chemical means by being
safe and economical. The biological pre-treatment can be
accomplished by using a blend of microorganisms able to withstand
such harsh alkaline conditions. In the present study, for the proper
pre-treatment of alkaline waste-waters, a package of alkalophilic
bacteria is formulated to neutralise the alkaline pH of the industrial
waste-waters. The developed microbial package is cost-effective as
well as environmental friendly.
Abstract: Existing underground pipe jacking methods use a
reinforcing rod in a steel tube to obtain structural stiffness. However,
some problems such as inconvenience of works and expensive
materials resulted from limited working space and reinforcing works
are existed. To resolve these problems, a new pipe jacking method,
namely PST (Prestressed Segment Tunnel) method, was developed
which used joint to connect the steel segment and form erection
structure. For evaluating the flexural capacity of the PST method
structure, a experimental test was conducted. The parameters
considered in the test were span-to-depth ratio of segment, diameter of
steel tube at the corner, prestressing force, and welding of joint. The
flexural behaviours with the effect of load capacity in serviceability
state according to different parameters were examined.. The frame
with long segments could increase flexural stiffness and the specimen
with large diameter of concave corner showed excellent resistance
ability to the negative moment. In addition, welding of joints increased
the flexural capacity.
Abstract: The reliability of distributed systems and computer
networks have been modeled by a probabilistic network or a graph G.
Computing the residual connectedness reliability (RCR), denoted by
R(G), under the node fault model is very useful, but is an NP-hard
problem. Since it may need exponential time of the network size to
compute the exact value of R(G), it is important to calculate its tight
approximate value, especially its lower bound, at a moderate
calculation time. In this paper, we propose an efficient algorithm for
reliability lower bound of distributed systems with unreliable nodes.
We also applied our algorithm to several typical classes of networks
to evaluate the lower bounds and show the effectiveness of our
algorithm.
Abstract: One of the most important problems to solve is eye
location for a driver fatigue monitoring system. This paper presents an
efficient method to achieve fast and accurate eye location in grey level
images obtained in the real-word driving conditions. The structure of
eye region is used as a robust cue to find possible eye pairs. Candidates
of eye pair at different scales are selected by finding regions which
roughly match with the binary eye pair template. To obtain real one,
all the eye pair candidates are then verified by using support vector
machines. Finally, eyes are precisely located by using binary vertical
projection and eye classifier in eye pair images. The proposed method
is robust to deal with illumination changes, moderate rotations, glasses
wearing and different eye states. Experimental results demonstrate its
effectiveness.
Abstract: Erwinia carotovora var. carotovora is the main cause of soft rot in potatoes. Hyphaene thebaica was studied for biocontrol of E. carotovora which inhibited growth of E. carotovora on solid medium, a comparative study of classical and ultrasound-assisted extractions of Hyphaene thebaica fruit. The use of ultrasound decreased significant the total time of treatment and increase the total amount of crude extract. The crude extract was subjected to determine the in vitro, by a bioassay technique revealed that the treatment of paper disks with ultrasound extraction of Hyphaene thebaica reduced the growth of pathogen and produced inhibition zones up to 38mm in diameter. The antioxidant activity of ultrasound-ethanolic extract of Doum fruits (Hyphaene thebaica) was determined. Data obtained showed that the extract contains the secondary metabolites such as Tannins, Saponin, Flavonoids, Phenols, Steroids, Terpenoids, Glycosides and Alkaloids.
Abstract: We describe a work with an evolutionary computing
algorithm for non photo–realistic rendering of a target image. The
renderings are produced by genetic programming. We have used two
different types of strokes: “empty triangle" and “filled triangle" in
color level. We compare both empty and filled triangular strokes to
find which one generates more aesthetic pleasing images. We found
the filled triangular strokes have better fitness and generate more
aesthetic images than empty triangular strokes.
Abstract: The study site was located in Ratchaburi Province,
Thailand. Four experimental plots in dry dipterocarp forest (DDF)
and four plots in mixed deciduous forest (MDF) were set up to
estimate the above-ground biomass of tree, sapling and bamboo. The
allometry equations were used to investigate above-ground biomass
of these vegetation. Seedling and other understory were determined
using direct harvesting method. Carbon storage in above-ground
biomass was calculated based on IPCC 2006.
The results showed that the above-ground biomass of DDF at
20-40% slope,
Abstract: The progress of concentrations of particular heavy metals was assessed in chosen localities in region Moravia, the Czech Republic, from 2007 to 2009. Particular metals were observed in localities with various types and characterization of zone. Pb, Ni, As and Cd were emphasized as a result of their toxicity and potential adverse health effect to the exposed population. The progress of metal concentrations and their health effects in the most polluted localities were examined. According to the results, the air pollution limit values were not exceeded. Based on the health risk assessment, the probability of developing tumorous diseases is acceptable, except for the increased probability of cancer risk from long-term exposure to As.
Abstract: This paper presents a tested research concept that
implements a complex evolutionary algorithm, genetic algorithm
(GA), in a multi-microcontroller environment. Parallel Distributed
Genetic Algorithm (PDGA) is employed in adaptive beam forming
technique to reduce power usage of adaptive antenna at WCDMA
base station. Adaptive antenna has dynamic beam that requires more
advanced beam forming algorithm such as genetic algorithm which
requires heavy computation and memory space. Microcontrollers are
low resource platforms that are normally not associated with GAs,
which are typically resource intensive. The aim of this project was to
design a cooperative multiprocessor system by expanding the role of
small scale PIC microcontrollers to optimize WCDMA base station
transmitter power. Implementation results have shown that PDGA
multi-microcontroller system returned optimal transmitted power
compared to conventional GA.
Abstract: This paper deals with behavior and capacity of
punching shear force for flat slabs produced from steel fiber
reinforced self compacting concrete (SFRSCC) by application
nonlinear finite element method. Nonlinear finite element analysis on
nine slab specimens was achieved by using ANSYS software. A
general description of the finite element method, theoretical modeling
of concrete and reinforcement are presented. The nonlinear finite
element analysis program ANSYS is utilized owing to its capabilities
to predict either the response of reinforced concrete slabs in the post
elastic range or the ultimate strength of a flat slabs produced from
steel fiber reinforced self compacting concrete (SFRSCC). In order to
verify the analytical model used in this research using test results of
the experimental data, the finite element analysis were performed
then a parametric study of the effect ratio of flexural reinforcement,
ratio of the upper reinforcement, and volume fraction of steel fibers
were investigated. A comparison between the experimental results
and those predicted by the existing models are presented. Results and
conclusions may be useful for designers, have been raised, and
represented.
Abstract: This study defines a methodology to compute unitary costs for freight transportation modes. The main objective was to gather relevant costs data to support the formulation and evaluation of railway, road, pipelines and port projects. This article will concentrate on the following steps: Compilation and analysis of relevant modal cost studies, Methodological adjustments to make cost figures comparable between studies, Definition of typology and scope of transportation modes, Analysis and validation of cost values for relevant freight transportation modes in Chile. In order to define the comparison methodology for the costs between the different transportation modes, it was necessary to consider that the relevant cost depends on who performs the comparison. Thus, for the transportation user (e.g. exporter) the pertinent costs are the mode tariffs, whereas from the operators perspective (e.g. rail manager), the pertinent costs are the operating costs of each mode.
Abstract: A preconditioned Jacobi (PJ) method is provided for solving fuzzy linear systems whose coefficient matrices are crisp Mmatrices and the right-hand side columns are arbitrary fuzzy number vectors. The iterative algorithm is given for the preconditioned Jacobi method. The convergence is analyzed with convergence theorems. Numerical examples are given to illustrate the procedure and show the effectiveness and efficiency of the method.
Abstract: This study presents the application of artificial
neural network for modeling the phenolic compound
migration through vertical soil column. A three layered feed
forward neural network with back propagation training
algorithm was developed using forty eight experimental data
sets obtained from laboratory fixed bed vertical column tests.
The input parameters used in the model were the influent
concentration of phenol(mg/L) on the top end of the soil
column, depth of the soil column (cm), elapsed time after
phenol injection (hr), percentage of clay (%), percentage of
silt (%) in soils. The output of the ANN was the effluent
phenol concentration (mg/L) from the bottom end of the soil
columns. The ANN predicted results were compared with the
experimental results of the laboratory tests and the accuracy of
the ANN model was evaluated.
Abstract: spherical porous carbon particles with
controllable porosity with a mean size of 2.5m have been
prepared using a spray drying method with organic particle
colloidal template. As a precursor, a mixing solution of carbon
nanopowder and polystyrene (PS) particles as a template was
used. The result showed that the particles with a good porous
structure could be obtained. The pore size and shape (spherical)
were identical to the initial template, giving a potential way for
further developments. The control of particle porosity was also
possible and reported in this paper, in which this control could
be achieved by means of PS concentration.
Abstract: The interaction among information and communication technology (ICT) industries is a recently ubiquitous phenomenon through fixed-mobile integration. To monitor the impact of interaction, previous research has mainly focused on measuring spillover effect among ICT industries using various methods. Among others, inter-industry analysis is one of the useful methods for examining spillover effect between industries. However, more complex ICT industries become, more important the impact within an industry is. Inter-industry analysis is limited in mirroring intra-relationships within an industry. Thus, this study applies the analytic network process (ANP) to measure the spillover effect, capturing all of the intra and inter-relationships. Using ANP-based intra and inter-industry analysis, the spillover effect is effectively measured, mirroring the complex structure of ICT industries. A main ICT industry and its linkages are also explored to show the current structure of ICT industries. The proposed approach is expected to allow policy makers to understand interactions of ICT industries and their impact.
Abstract: This paper presented the results of an experimental
investigation into the axial fatigue behavior of a 5086 aluminum
alloy which have several notch-aspect ratios a0/c0 and notch
thickness ratio a/t with semi-elliptical surface cracks. Tests were
conducted in la b air for stress levels of 50 % of their yield
strength. Experiments were carried out for various notch to
thickness ratios. Crack growth rates of test specimens both in
surface and depth directions were determined by using die
penetration method. Fuzzy Logic method was used to predict the
deep direction crack growth because the dept of the crack is
considerably difficult to measure.
Abstract: This paper reports on the results of experimental investigations on the performance of a jet pump operated under selected primary flows to optimize the related parameters. For this purpose a two-phase flow jet pump was used employing various profiles of nozzles as the primary device which was designed, fabricated and used along with the combination of mixing tube and diffuser. The profiles employed were circular, conical, and elliptical. The diameter of the nozzle used was 4 mm. The area ratio of the jet pump was 0.16. The test facility created for this purpose was an open loop continuous circulation system. Performance of the jet pump was obtained as iso-efficiency curves on characteristic curves drawn for various water flow rates. To perform the suction capability, evacuation test was conducted at best efficiency point for all the profiles.
Abstract: This paper present a new way to find the aerodynamic
characteristic equation of missile for the numerical trajectories
prediction more accurate. The goal is to obtain the polynomial
equation based on two missile characteristic parameters, angle of
attack (α ) and flight speed (ν ). First, the understudied missile is
modeled and used for flow computational model to compute
aerodynamic force and moment. Assume that performance range of
understudied missile where range -10< α
Abstract: In this paper, numerical simulation is used to
investigate the thermal performance of liquid cooling heatsink with
microchannels due to geometric arrangement. Commercial software
ICEPAK is utilized for the analysis. The considered parameters
include aspect ratio, porosity and the length and height of
microchannel. The aspect ratio varies from 3 to 16 and the length of
microchannel is 10mm, 14mm, and 18mm. The height of
microchannel is 2mm, 3mm and 4mm. It is found short channel have
better thermal efficiency than long channel at 490Pa. No matter the
length of channel the best aspect ratio is 4. It is also noted that pressure
difference at 2940Pa the best aspect ratio from 4 to 8, it means pressure
difference affect aspect ratio, effective thermal resistance at low
pressure difference but lower effective thermal resistance at high
pressure difference.