Abstract: The current study describes a multi-objective optimization technique for positioning of houses in a residential neighborhood. The main task is the placement of residential houses in a favorable configuration satisfying a number of objectives. Solving the house layout problem is a challenging task. It requires an iterative approach to satisfy design requirements (e.g. energy efficiency, skyview, daylight, roads network, visual privacy, and clear access to favorite views). These design requirements vary from one project to another based on location and client preferences. In the Gulf region, the most important socio-cultural factor is the visual privacy in indoor space. Hence, most of the residential houses in this region are surrounded by high fences to provide privacy, which has a direct impact on other requirements (e.g. daylight and direction to favorite views). This investigation introduces a novel technique to optimally locate and orient residential buildings to satisfy a set of design requirements. The developed technique explores the search space for possible solutions. This study considers two dimensional house planning problems. However, it can be extended to solve three dimensional cases.
Abstract: A new stochastic algorithm called Probabilistic Global Search Johor (PGSJ) has recently been established for global optimization of nonconvex real valued problems on finite dimensional Euclidean space. In this paper we present convergence guarantee for this algorithm in probabilistic sense without imposing any more condition. Then, we jointly utilize this algorithm along with control
parameterization technique for the solution of constrained optimal control problem. The numerical simulations are also included to illustrate the efficiency and effectiveness of the PGSJ algorithm in the solution of control problems.
Abstract: The control of sprayer boom undesired vibrations pose a great challenge to investigators due to various disturbances and conditions. Sprayer boom movements lead to reduce of spread efficiency and crop yield. This paper describes the design of a novel control method for an active suspension system applying proportional-integral-derivative (PID) controller with an active force control (AFC) scheme integration of an iterative learning algorithm employed to a sprayer boom. The iterative learning as an intelligent method is principally used as a method to calculate the best value of the estimated inertia of the sprayer boom needed for the AFC loop. Results show that the proposed AFC-based scheme performs much better than the standard PID control technique. Also, this shows that the system is more robust and accurate.
Abstract: This paper considers a multi criteria cell formation
problem in Cellular Manufacturing System (CMS). Minimizing the
number of voids and exceptional elements in cells simultaneously are
two proposed objective functions. This problem is an Np-hard
problem according to the literature, and therefore, we can-t find the
optimal solution by an exact method. In this paper we developed two
ant algorithms, Ant Colony Optimization (ACO) and Max-Min Ant
System (MMAS), based on Data Envelopment Analysis (DEA). Both
of them try to find the efficient solutions based on efficiency concept
in DEA. Each artificial ant is considered as a Decision Making Unit
(DMU). For each DMU we considered two inputs, the values of
objective functions, and one output, the value of one for all of them.
In order to evaluate performance of proposed methods we provided
an experimental design with some empirical problem in three
different sizes, small, medium and large. We defined three different
criteria that show which algorithm has the best performance.
Abstract: Many algorithms are available for sorting the unordered elements. Most important of them are Bubble sort, Heap sort, Insertion sort and Shell sort. These algorithms have their own pros and cons. Shell Sort which is an enhanced version of insertion sort, reduces the number of swaps of the elements being sorted to minimize the complexity and time as compared to insertion sort. Shell sort improves the efficiency of insertion sort by quickly shifting values to their destination. Average sort time is O(n1.25), while worst-case time is O(n1.5). It performs certain iterations. In each iteration it swaps some elements of the array in such a way that in last iteration when the value of h is one, the number of swaps will be reduced. Donald L. Shell invented a formula to calculate the value of ?h?. this work focuses to identify some improvement in the conventional Shell sort algorithm. ''Enhanced Shell Sort algorithm'' is an improvement in the algorithm to calculate the value of 'h'. It has been observed that by applying this algorithm, number of swaps can be reduced up to 60 percent as compared to the existing algorithm. In some other cases this enhancement was found faster than the existing algorithms available.
Abstract: Designing a simulated system and training it to optimize its tasks in simulated environment helps the designers to avoid problems that may appear when designing the system directly in real world. These problems are: time consuming, high cost, high errors percentage and low efficiency and accuracy of the system. The proposed system will investigate and improve the efficiency and accuracy of a simulated robot to choose correct behavior to perform its task. In this paper, machine learning, which uses genetic algorithm, is adopted. This type of machine learning is called genetic-based machine learning in which a distributed classifier system is used to improve the efficiency and accuracy of the robot. Consequently, it helps the robot to achieve optimal action.
Abstract: The purpose of Grid computing is to utilize
computational power of idle resources which are distributed in
different areas. Given the grid dynamism and its decentralize
resources, there is a need for an efficient scheduler for scheduling
applications. Since task scheduling includes in the NP-hard problems
various researches have focused on invented algorithms especially
the genetic ones. But since genetic is an inherent algorithm which
searches the problem space globally and does not have the efficiency
required for local searching, therefore, its combination with local
searching algorithms can compensate for this shortcomings. The aim
of this paper is to combine the genetic algorithm and GELS (GAGELS)
as a method to solve scheduling problem by which
simultaneously pay attention to two factors of time and number of
missed tasks. Results show that the proposed algorithm can decrease
makespan while minimizing the number of missed tasks compared
with the traditional methods.
Abstract: In order to enhance the usability of the human computer interface (HCI) on the touchscreen, this study explored the optimal tactile depth and effect of visual cues on the user-s tendency to touch the touchscreen icons. The experimental program was designed on the touchscreen in this study. Results indicated that the ratio of the icon size to the tactile depth was 1:0.106. There were significant effects of experienced users and novices on the tactile feedback depth (p < 0.01). In addition, the results proved that the visual cues provided a feedback that helped to guide the user-s touch icons accurately and increased the capture efficiency for a tactile recognition field. This tactile recognition field was 18.6 mm in length. There was consistency between the experienced users and novices under the visual cue effects. Finally, the study developed an applied design with touch feedback for touchscreen icons.
Abstract: Pollution emission levels of aircraft engines are a
nowadays high concern. Any technological advance that could reduce
emission levels is always welcome. In what concerns aircraft engines,
a possible solution for this problem could be the use of regenerators
and intercoolers. These components might reduce the specific fuel
consumption, increase efficiency and specific thrust and consequently
reduce the pollution levels of the engine. This is not a novel solution.
These heat exchangers are already is use in stationary engines. For
aircraft engines, the extra weight of the needed hardware could
overcome the fuel saved. This work compares a conventional engine
with configurations that use intercoolers and regenerators.
Abstract: In this study, the dispersed model is used to predict
gas phase concentration, liquid drop concentration. The venturi
scrubber efficiency is calculated by gas phase concentration. The
modified model has been validated with available experimental data
of Johnstone, Field and Tasler for a range of throat gas velocities,
liquid to gas ratios and particle diameters and is used to study the
effect of some design parameters on collection efficiency.
Abstract: An actual power plant, which is the power plant of Iron and Steel Factory at Misurata city in Libya , has been modeled using Matlab in order to compare its results to the actual results of the actual cycle. This paper concentrates on two factors:
a- The comparison between exergy losses in the actual cycle and the modeled cycle.
b- The effect of extracting pressure on temperature water at boiler inlet.
Closed heat exchangers used in this plant have been substituted by open heat exchangers in the current study of the modeled power plant and the required changes in the pressure have been considered. In the following investigation the two points mentioned above are taken in consideration.
Abstract: Heavy rainfall greatly affects the aerodynamic performance of the aircraft. There are many accidents of aircraft caused by aerodynamic efficiency degradation by heavy rain.
In this Paper we have studied the heavy rain effects on the aerodynamic efficiency of cambered NACA 64-210 and symmetric
NACA 0012 airfoils. Our results show significant increase in drag and decrease in lift. We used preprocessing software gridgen for creation of geometry and mesh, used fluent as solver and techplot as postprocessor. Discrete phase modeling called DPM is used to model the rain particles using two phase flow approach. The rain particles are assumed to be inert.
Both airfoils showed significant decrease in lift and increase in drag in simulated rain environment. The most significant difference between these two airfoils was the NACA 64-210 more sensitivity than NACA 0012 to liquid water content (LWC). We believe that the results showed in this paper will be useful for the designer of the commercial aircrafts and UAVs, and will be helpful for training of the pilots to control the airplanes in heavy rain.
Abstract: In China, with the rapid urbanization and
industrialization, and highly accelerated economic development have
resulted in degradation of water resource. The water quality
deterioration usual result from eutrophication in most cases, so how to
dispose this type pollution water higher efficiently is an urgent task.
Hower, different with traditional technology, constructed wetlands are
effective treatment systems that can be very useful because they are
simple technology and low operational cost. A pilot-scale treatment
including constructed wetlands was constructed at XingYun Lake,
Yuxi, China, and operated as primary treatment measure before
eutrophic-lake water draining to riverine landscape. Water quality
indices were determined during the experiment, the results indicated
that treatment removal efficiencies were high for Nitrate nitrogen,
Chlorophyll–a and Algae, the final removal efficiency reached to
95.20%, 93.33% and 99.87% respectively, but the removal efficiency
of Total phosphorous and Total nitrogen only reach to 68.83% and
50.00% respectively.
Abstract: Laser Metal Deposition (LMD) is an additive manufacturing process with capabilities that include: producing new
part directly from 3 Dimensional Computer Aided Design (3D CAD)
model, building new part on the existing old component and repairing an existing high valued component parts that would have
been discarded in the past. With all these capabilities and its advantages over other additive manufacturing techniques, the
underlying physics of the LMD process is yet to be fully understood probably because of high interaction between the processing
parameters and studying many parameters at the same time makes it
further complex to understand. In this study, the effect of laser power
and powder flow rate on physical properties (deposition height and
deposition width), metallurgical property (microstructure) and
mechanical (microhardness) properties on laser deposited most
widely used aerospace alloy are studied. Also, because the Ti6Al4V
is very expensive, and LMD is capable of reducing buy-to-fly ratio
of aerospace parts, the material utilization efficiency is also studied.
Four sets of experiments were performed and repeated to establish repeatability using laser power of 1.8 kW and 3.0 kW, powder flow
rate of 2.88 g/min and 5.67 g/min, and keeping the gas flow rate and
scanning speed constant at 2 l/min and 0.005 m/s respectively. The
deposition height / width are found to increase with increase in laser
power and increase in powder flow rate. The material utilization is favoured by higher power while higher powder flow rate reduces
material utilization. The results are presented and fully discussed.
Abstract: Recent quasi-experimental evaluation of the Canadian Active Labour Market Policies (ALMP) by Human Resources and Skills Development Canada (HRSDC) has provided an opportunity to examine alternative methods to estimating the incremental effects of Employment Benefits and Support Measures (EBSMs) on program participants. The focus of this paper is to assess the efficiency and robustness of inverse probability weighting (IPW) relative to kernel matching (KM) in the estimation of program effects. To accomplish this objective, the authors compare pairs of 1,080 estimates, along with their associated standard errors, to assess which type of estimate is generally more efficient and robust. In the interest of practicality, the authorsalso document the computationaltime it took to produce the IPW and KM estimates, respectively.
Abstract: In this paper, we study the numerical method for solving second-order fuzzy differential equations using Adomian method under strongly generalized differentiability. And, we present an example with initial condition having four different solutions to illustrate the efficiency of the proposed method under strongly generalized differentiability.
Abstract: Renewable water resources are crucial production
variables in arid and semi-arid regions where intensive agriculture is
practiced to meet ever-increasing demand for food and fiber. This is
crucial for the Dez and Moghan command areas where water delivery
problems and adverse environmental issues are widespread. This
paper aims to identify major problems areas using on-farm surveys of
200 farmers, agricultural extensionists and water suppliers which was
complemented by secondary data and field observations during 2010-
2011 cultivating season. The SPSS package was used to analyze and
synthesis data. Results indicated inappropriate canal operations in
both schemes, though there was no unanimity about the underlying
causes. Inequitable and inflexible distribution was found to be rooted
in deficient hydraulic structures particularly in the main and
secondary canals. The inadequacy and inflexibility of water
scheduling regime was the underlying causes of recurring pest and
disease spread which often led to the decline of crop yield and
quality, although these were not disputed, the water suppliers were
not prepared to link with the deficiencies in the operation of the main
and secondary canals. They rather attributed these to the prevailing
salinity; alkalinity, water table fluctuations and leaching of the
valuable agro-chemical inputs from the plants- route zone with farreaching
consequences. Examples of these include the pollution of
ground and surface resources due to over-irrigation at the farm level
which falls under the growers- own responsibility. Poor irrigation
efficiency and adverse environmental problems were attributed to
deficient and outdated farming practices that were in turn rooted in
poor extension programs and irrational water charges.
Abstract: Since DVB-RCS has been successively implemented, the mobile communication on the multi-beam satellite communication is attractive attention. And the DVB-RCS standard sets up to support mobility of a RCST. In the case of the spot-beam satellite system, the received signal strength does not differ largely between the center and the boundary of the beam. Thus, the RSS based handoff detection algorithm is not benefit to the satellite system as a terrestrial system. Therefore we propose an Adaptive handoff detection algorithm based on RCST mobility information. Our handoff detection algorithm not only can be used as centralized handoff detection algorithm but also removes uncertainties of handoff due to the variation of RSS. Performances were compared with RSS based handoff algorithm. Simulation results show that the proposed handoff detection algorithm not only achieved better handoff and link degradation rate, but also achieved better forward link spectral efficiency.
Abstract: Content-based Image Retrieval (CBIR) aims at searching image databases for specific images that are similar to a given query image based on matching of features derived from the image content. This paper focuses on a low-dimensional color based indexing technique for achieving efficient and effective retrieval performance. In our approach, the color features are extracted using the mean shift algorithm, a robust clustering technique. Then the cluster (region) mode is used as representative of the image in 3-D color space. The feature descriptor consists of the representative color of a region and is indexed using a spatial indexing method that uses *R -tree thus avoiding the high-dimensional indexing problems associated with the traditional color histogram. Alternatively, the images in the database are clustered based on region feature similarity using Euclidian distance. Only representative (centroids) features of these clusters are indexed using *R -tree thus improving the efficiency. For similarity retrieval, each representative color in the query image or region is used independently to find regions containing that color. The results of these methods are compared. A JAVA based query engine supporting query-by- example is built to retrieve images by color.
Abstract: Using of natural lighting has come into prominence in
constructed buildings, especially in last ten years, under scope of
energy efficiency. Natural lighting methods are one of the methods
that aim to take advantage of day light in maximum level and
decrease using of artificial lighting. Increasing of day light amount in
buildings by using suitable methods will give optimum result in
terms of comfort and energy saving when the daylight-artificial light
integration is ensured with a suitable control system. Using of natural
light in places that require lighting will ensure energy saving in great
extent. With this study, it is aimed to save energy used for purpose of
lighting. Under this scope, lighting of a scanning laboratory of a
hospital was realized by using a lighting automation containing
natural and artificial lighting. In natural lighting, light pipes were
used and in artificial lighting, dimmable power LED modules were
used. Necessity of lighting was followed with motion sensors. The
lighting automation containing natural and artificial light was ensured
with fuzzy logic control. At the scanning laboratory where this
application was realized, energy saving in lighting was obtained.