Abstract: Orthogonal Frequency Division Multiplexing
(OFDM) is an efficient method of data transmission for high speed
communication systems. However, the main drawback of OFDM
systems is that, it suffers from the problem of high Peak-to-Average
Power Ratio (PAPR) which causes inefficient use of the High Power
Amplifier and could limit transmission efficiency. OFDM consist of
large number of independent subcarriers, as a result of which the
amplitude of such a signal can have high peak values. In this paper,
we propose an effective reduction scheme that combines DCT and
SLM techniques. The scheme is composed of the DCT followed by
the SLM using the Riemann matrix to obtain phase sequences for the
SLM technique. The simulation results show PAPR can be greatly
reduced by applying the proposed scheme. In comparison with
OFDM, while OFDM had high values of PAPR –about 10.4dB our
proposed method achieved about 4.7dB reduction of the PAPR with
low complexities computation. This approach also avoids
randomness in phase sequence selection, which makes it simpler to
decode at the receiver. As an added benefit, the matrices can be
generated at the receiver end to obtain the data signal and hence it is
not required to transmit side information (SI).
Abstract: Fixed-bed slow pyrolysis experiments of rice husk
have been conducted to determine the effect of pyrolysis
temperature, heating rate, particle size and reactor length on the
pyrolysis product yields. Pyrolysis experiments were performed at
pyrolysis temperature between 400 and 600°C with a constant
heating rate of 60°C/min and particle sizes of 0.60-1.18 mm. The
optimum process conditions for maximum liquid yield from the rice
husk pyrolysis in a fixed bed reactor were also identified. The highest
liquid yield was obtained at a pyrolysis temperature of 500°C,
particle size of
1.18-1.80 mm, with a heating rate of 60°C/min in a 300 mm length
reactor. The obtained yield of, liquid, gas and solid were found be in
the range of 22.57-31.78 %, 27.75-42.26 % and 34.17-42.52 % (all
weight basics) respectively at different pyrolysis conditions. The
results indicate that the effects of pyrolysis temperature and particle
size on the pyrolysis yield are more significant than that of heating
rate and reactor length. The functional groups and chemical
compositions present in the liquid obtained at optimum conditions
were identified by Fourier Transform-Infrared (FT-IR) spectroscopy
and Gas Chromatography/ Mass Spectroscopy (GC/MS) analysis
respectively.
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: In this paper, we consider the problem for identifying the unknown source in the Poisson equation. A modified Tikhonov regularization method is presented to deal with illposedness of the problem and error estimates are obtained with an a priori strategy and an a posteriori choice rule to find the regularization parameter. Numerical examples show that the proposed method is effective and stable.
Abstract: Clustering is a very well known technique in data mining. One of the most widely used clustering techniques is the kmeans algorithm. Solutions obtained from this technique depend on the initialization of cluster centers and the final solution converges to local minima. In order to overcome K-means algorithm shortcomings, this paper proposes a hybrid evolutionary algorithm based on the combination of PSO, SA and K-means algorithms, called PSO-SA-K, which can find better cluster partition. The performance is evaluated through several benchmark data sets. The simulation results show that the proposed algorithm outperforms previous approaches, such as PSO, SA and K-means for partitional clustering problem.
Abstract: In this paper, we propose a method to extract the road
signs. Firstly, the grabbed image is converted into the HSV color space
to detect the road signs. Secondly, the morphological operations are
used to reduce noise. Finally, extract the road sign using the geometric
property. The feature extraction of road sign is done by using the color
information. The proposed method has been tested for the real
situations. From the experimental results, it is seen that the proposed
method can extract the road sign features effectively.
Abstract: This work concerns the topological optimization
problem for determining the optimal petroleum refinery
configuration. We are interested in further investigating and
hopefully advancing the existing optimization approaches and
strategies employing logic propositions to conceptual process
synthesis problems. In particular, we seek to contribute to this
increasingly exciting area of chemical process modeling by
addressing the following potentially important issues: (a) how the
formulation of design specifications in a mixed-logical-and-integer
optimization model can be employed in a synthesis problem to enrich
the problem representation by incorporating past design experience,
engineering knowledge, and heuristics; and (b) how structural
specifications on the interconnectivity relationships by space (states)
and by function (tasks) in a superstructure should be properly
formulated within a mixed-integer linear programming (MILP)
model. The proposed modeling technique is illustrated on a case
study involving the alternative processing routes of naphtha, in which
significant improvement in the solution quality is obtained.
Abstract: The design requirements for successful human
accommodation in urban spaces are well known; and the range of
facilities available for meeting urban water quality and quantity
requirements is also well established. Their competing requirements
must be reconciled in order for urban spaces to be successful for
both. This paper outlines the separate human and water imperatives
and their interactions in urban spaces. Stormwater management
facilities- relative potential contributions to urban spaces are
contrasted, and design choices for achieving those potentials are
described. This study uses human success of urban space as the
evaluative criterion of stormwater amenity: human values call on
stormwater facilities to contribute to successful human spaces.
Placing water-s contribution under the overall idea of successful
urban space is an evolution from previous subjective evaluations.
The information is based on photographs and notes from
approximately 1,000 stormwater facilities and urban sites collected
during the last 35 years in North America and overseas, and the
author-s experience on multi-disciplinary design teams. This
conceptual study combines the disciplinary roles of engineering,
landscape architecture, and sociology in effecting successful urban
design.
Abstract: Unlike its conventional counterpart, Islamic principles
forbid Islamic banks to take any interest-related income and thus
makes deposits from depositors as an important source of fund for its
operational and financing. Consequently, the risk of deposit
withdrawal by depositors is an important aspect that should be wellmanaged
in Islamic banking. This paper aims to investigate factors
that influence depositors- withdrawal behavior in Islamic banks,
particularly in Malaysia, using the framework of theory of reasoned
action. A total of 368 respondents from Klang valley are involved in
the analysis. The paper finds that all the constructs variable i.e.
normative beliefs, subjective norms, behavioral beliefs, and attitude
towards behavior are perceived to be distinct by the respondents. In
addition, the structural equation model is able to verify the structural
relationships between subjective norms, attitude towards behavior
and behavioral intention. Subjective norms gives more influence to
depositors- decision on deposit withdrawal compared to attitude
towards behavior.
Abstract: A multi-board run-time reconfigurable (MRTR)
system for evolvable hardware (EHW) is introduced with the aim to
implement on hardware the bidirectional incremental evolution (BIE)
method. The main features of this digital intrinsic EHW solution rely
on the multi-board approach, the variable chromosome length
management and the partial configuration of the reconfigurable
circuit. These three features provide a high scalability to the solution.
The design has been written in VHDL with the concern of not being
platform dependant in order to keep a flexibility factor as high as
possible. This solution helps tackling the problem of evolving
complex task on digital configurable support.
Abstract: An appropriate method for fault identification and classification on extra high voltage transmission line using discrete wavelet transform is proposed in this paper. The sharp variations of the generated short circuit transient signals which are recorded at the sending end of the transmission line are adopted to identify the fault. The threshold values involve fault classification and these are done on the basis of the multiresolution analysis. A comparative study of the performance is also presented for Discrete Fourier Transform (DFT) based Artificial Neural Network (ANN) and Discrete Wavelet Transform (DWT). The results prove that the proposed method is an effective and efficient one in obtaining the accurate result within short duration of time by using Daubechies 4 and 9. Simulation of the power system is done using MATLAB.
Abstract: In This Article We establish moment inequality of
dependent random variables,furthermore some theorems of strong law
of large numbers and complete convergence for sequences of dependent
random variables. In particular, independent and identically
distributed Marcinkiewicz Law of large numbers are generalized to
the case of m0-dependent sequences.
Abstract: Vision-based intelligent vehicle applications often require large amounts of memory to handle video streaming and image processing, which in turn increases complexity of hardware and software. This paper presents an FPGA implement of a vision-based blind spot warning system. Using video frames, the information of the blind spot area turns into one-dimensional information. Analysis of the estimated entropy of image allows the detection of an object in time. This idea has been implemented in the XtremeDSP video starter kit. The blind spot warning system uses only 13% of its logic resources and 95k bits block memory, and its frame rate is over 30 frames per sec (fps).
Abstract: A Web-services based grid infrastructure is evolving to be readily available in the near future. In this approach, the Web services are inherited (encapsulated or functioned) into the same existing Grid services class. In practice there is not much difference between the existing Web and grid infrastructure. Grid services emerged as stateful web services. In this paper, we present the key components of web-services based grid and also how the resource discovery is performed on web-services based grid considering resource discovery, as a critical service, to be provided by any type of grid.
Abstract: Chess is one of the indoor games, which improves the
level of human confidence, concentration, planning skills and
knowledge. The main objective of this paper is to help the chess
players to improve their chess openings using data mining
techniques. Budding Chess Players usually do practices by analyzing
various existing openings. When they analyze and correlate
thousands of openings it becomes tedious and complex for them. The
work done in this paper is to analyze the best lines of Blackmar-
Diemer Gambit(BDG) which opens with White D4... using data
mining analysis. It is carried out on the collection of winning games
by applying association rules. The first step of this analysis is
assigning variables to each different sequence moves. In the second
step, the sequence association rules were generated to calculate
support and confidence factor which help us to find the best
subsequence chess moves that may lead to winning position.
Abstract: Determination of nano particle size is substantial since
the nano particle size exerts a significant effect on various properties
of nano materials. Accordingly, proposing non-destructive, accurate
and rapid techniques for this aim is of high interest. There are some
conventional techniques to investigate the morphology and grain size
of nano particles such as scanning electron microscopy (SEM),
atomic force microscopy (AFM) and X-ray diffractometry (XRD).
Vibrational spectroscopy is utilized to characterize different
compounds and applied for evaluation of the average particle size
based on relationship between particle size and near infrared spectra
[1,4] , but it has never been applied in quantitative morphological
analysis of nano materials. So far, the potential application of nearinfrared
(NIR) spectroscopy with its ability in rapid analysis of
powdered materials with minimal sample preparation, has been
suggested for particle size determination of powdered
pharmaceuticals. The relationship between particle size and diffuse
reflectance (DR) spectra in near infrared region has been applied to
introduce a method for estimation of particle size. Back propagation
artificial neural network (BP-ANN) as a nonlinear model was applied
to estimate average particle size based on near infrared diffuse
reflectance spectra. Thirty five different nano TiO2 samples with
different particle size were analyzed by DR-FTNIR spectrometry and
the obtained data were processed by BP- ANN.
Abstract: The Japanese integrative approach to social systems
can be observed in supply chain management as well as in the
relationship between public and private sectors. Both the Lean
Production System and the Developmental State Model are
characterized by efforts towards the achievement of mutual goals,
resulting in initiatives for capacity building which emphasize the
system level. In Brazil, although organizations undertake efforts to
build capabilities at the individual and organizational levels, the
system level is being neglected. Fieldwork data confirmed the findings
of other studies in terms of the lack of integration in supply chain
management in the Brazilian automobile industry. Moreover, due to
the absence of an active role of the Brazilian state in its relationship
with the private sector, automakers are not fully exploiting the
opportunities in the domestic and regional markets. For promoting a
higher level of economic growth as well as to increase the degree of
spill-over of technologies and techniques, a more integrative approach
is needed.
Abstract: The Major Depressive Disorder has been a burden of
medical expense in Taiwan as well as the situation around the world.
Major Depressive Disorder can be defined into different categories by
previous human activities. According to machine learning, we can
classify emotion in correct textual language in advance. It can help
medical diagnosis to recognize the variance in Major Depressive
Disorder automatically. Association language incremental is the
characteristic and relationship that can discovery words in sentence.
There is an overlapping-category problem for classification. In this
paper, we would like to improve the performance in classification in
principle of no overlapping-category problems. We present an
approach that to discovery words in sentence and it can find in high
frequency in the same time and can-t overlap in each category, called
Association Language Features by its Category (ALFC).
Experimental results show that ALFC distinguish well in Major
Depressive Disorder and have better performance. We also compare
the approach with baseline and mutual information that use single
words alone or correlation measure.
Abstract: In order to optimize annual IT spending and to reduce
the complexity of an entire system architecture, SOA trials have been
started. It is common knowledge that to design an SOA system we
have to adopt the top-down approach, but in reality silo systems are
being made, so these companies cannot reuse newly designed services,
and cannot enjoy SOA-s economic benefits. To prevent this situation,
we designed a generic SOA development process referred to as the
architecture of “mass customization."
To define the generic detail development processes, we did a case
study on an imaginary company. Through the case study, we could
define the practical development processes and found this could vastly
reduce updating development costs.