Abstract: The use of optical technologies in the
telecommunications has been increasing due to its ability to transmit
large amounts of data over long distances. However, as in all systems
of data transmission, optical communication channels suffer from
undesirable and non-deterministic effects, being essential to know the
same. Thus, this research allows the assessment of these effects, as
well as their characterization and beneficial uses of these effects.
Abstract: Banda Sea Collision Zone (BSCZ) is the result of the
interaction and convergence of Indo-Australian plate, Eurasian plate
and Pacific plate. This location is located in eastern Indonesia. This
zone has a very high seismic activity. In this research, we will
calculate the rate (λ) and Mean Square Error (MSE). By this result,
we will classification earthquakes distribution in the BSCZ with the
point process approach. Chi-square is used to determine the type of
earthquakes distribution in the sub region of BSCZ. The data used in
this research is data of earthquakes with a magnitude ≥ 6 SR for the
period 1964-2013 and sourced from BMKG Jakarta. This research is
expected to contribute to the Moluccas Province and surrounding
local governments in performing spatial plan document related to
disaster management.
Abstract: Objective: Acute coronary syndrome is a clinical
condition encompassing ST segments elevation myocardial
infraction, Non ST segment is elevation myocardial infraction and un
stable angina is characterized by ruptured coronary plaque, stress and
myocardial injury. Angina pectoris is a pressure like pain in the chest
that is induced by exertion or stress and relived with in the minute
after cessation of effort or using sublingual nitroglycerin. The present
research was undertaken to study the drug utilization pattern of
antiplatelet drugs for the ischemic heart disease in a tertiary care
hospital. Method: The present study is retrospective drug utilization
study and study period is 6months. The data is collected from the
discharge case sheet of general medicine department from medical
department Rajiv Gandhi institute of medical sciences, Kadapa. The
tentative sample size fixed was 250 patients. Out of 250 cases 19
cases was excluded because of unrelated data. Results: A total of 250
prescriptions were collected for the study according to the inclusion
criteria 233 prescriptions were diagnosed with ischemic heart disease
17 prescriptions were excluded due to unrelated information. out of
233 prescriptions 128 are male (54.9%) and 105 patients are were
female (45%). According to the gender distribution, the prevalence of
ischemic heart disease in males are 90 (70.31%) and females are 39
(37.1%). In the same way the prevalence of ischemic heart disease
along with cerebrovascular disease in males are 39 (29.6%) and
females are 66 (62.6%). Conclusion: We found that 94.8% of drug
utilization of antiplatelet drugs was achieved in the Rajiv Gandhi
institute of medical sciences, Kadapa from 2011-2012.
Abstract: In this corporate world, the technology of Web
services has grown rapidly and its significance for the development
of web based applications gradually rises over time. The success of
Business to Business integration rely on finding novel partners and
their services in a global business environment. However, the
selection of the most suitable Web service from the list of services
with the identical functionality is more vital. The satisfaction level of
the customer and the provider’s reputation of the Web service are
primarily depending on the range it reaches the customer’s
requirements. In most cases, the customer of the Web service feels
that he is spending for the service which is undelivered. This is
because the customer always thinks that the real functionality of the
web service is not reached. This will lead to change of the service
frequently. In this paper, a framework is proposed to evaluate the
Quality of Service (QoS) and its cost that makes the optimal
correlation between each other. In addition, this research work
proposes some management decision against the functional deviancy
of the web service that is guaranteed at time of selection.
Abstract: The aim of this study is to examine, through
experimentation in the laboratory, the supercritical flow in the
presence of an obstacle in a rectangular channel. The supercritical
regime in the whole hydraulic channel is achieved by adding a
convergent. We will observe the influence of the obstacle shape and
dimension on the characteristics of the supercritical flow, mainly the
free-surface elevation and the velocity profile. The velocity
measurements have been conducted with the one dimension laser
anemometry technique.
Abstract: Manufacturing process has been considered as one of
the most important activity in business process. It correlates with
productivity and quality of the product so industries could fulfill
customer’s demand. With the increasing demand from customer,
industries must improve their manufacturing ability such as shorten
lead-time and reduce wastes on their process. Lean manufacturing
has been considered as one of the tools to waste elimination in
manufacturing or service industry. Workforce development is one
practice in lean manufacturing that can reduce waste generated from
operator such as waste of unnecessary motion. Anthropometric
approach is proposed to determine the recommended measurement in
operator’s work area. The method will get some dimensions from
Indonesia people that related to piston workstation. The result from
this research can be obtained new design for the work area
considering ergonomic aspect.
Abstract: Web Usage Mining is the application of data mining
techniques to find usage patterns from web log data, so as to grasp
required patterns and serve the requirements of Web-based
applications. User’s expertise on the internet may be improved by
minimizing user’s web access latency. This may be done by
predicting the future search page earlier and the same may be prefetched
and cached. Therefore, to enhance the standard of web
services, it is needed topic to research the user web navigation
behavior. Analysis of user’s web navigation behavior is achieved
through modeling web navigation history. We propose this technique
which cluster’s the user sessions, based on the K-medoids technique.
Abstract: Value addition to agricultural produce is of possible
potential in reducing poverty, improving food security and
malnutrition, therefore the need to develop small and microenterprises
of sweet potato production. A study was carried out in Nigeria to determine the acceptability
of blends sweet potato (Ipomea batatas) and commodities yellow
maize (Zea mays), millet (Pennisetum glaucum), soybean (Glycine
max), bambara groundnut (Vigna subterranean), guinea corn
(Sorghum vulgare), wheat (Triticum aestivum), and roselle (Hibiscus
sabdariffa) through sensory evaluation. Sweet potato (Ipomea batatas) roots were processed using two
methods: oven and sun drying. The blends were also assessed in
terms of functional, chemical and color properties. Most acceptable blends include BAW (80:20 of sweet
potato/wheat), BBC (80:20 of sweet potato/guinea corn), AAB (60:40
of sweet potato/guinea corn), YTE (100% soybean), TYG (100%
sweet potato), KTN (100% wheat flour), XGP (80:20 of sweet
potato/soybean), XAX (60:40 of sweet potato/wheat), LSS (100%
Roselle), CHK (100% Guinea corn), and ABC (60:40% of sweet
potato/ yellow maize). In addition, carried out chemical analysis
revealed that sweet potato has high percentage of vitamins A and C,
potassium (K), manganese (Mn), calcium (Ca), magnesium (Mg) and
iron (Fe) and fibre content. There is also an increase of vitamin A and
Iron in the blended products.
Abstract: In this paper, de Laval rotor system has been
characterized by a hinge model and its transient response numerically
treated for a dynamic solution. The effect of the ensuing non-linear
disturbances namely rub and breathing crack is numerically
simulated. Subsequently, three analysis methods: Orbit Analysis, Fast
Fourier Transform (FFT), and Wavelet Transform (WT) are
employed to extract features of the vibration signal of the faulty
system. An analysis of the system response orbits clearly indicates
the perturbations due to the rotor-to-stator contact. The sensitivities
of WT to the variation in system speed have been investigated by
Continuous Wavelet Transform (CWT). The analysis reveals that
features of crack, rubs and unbalance in vibration response can be
useful for condition monitoring. WT reveals its ability to detect nonlinear
signal, and obtained results provide a useful tool method for
detecting machinery faults.
Abstract: Opportunistic Routing (OR) increases the
transmission reliability and network throughput. Traditional routing
protocols preselects one or more predetermined nodes before
transmission starts and uses a predetermined neighbor to forward a
packet in each hop. The opportunistic routing overcomes the
drawback of unreliable wireless transmission by broadcasting one
transmission can be overheard by manifold neighbors. The first
cooperation-optimal protocol for Multirate OR (COMO) used to
achieve social efficiency and prevent the selfish behavior of the
nodes. The novel link-correlation-aware OR improves the
performance by exploiting the miscellaneous low correlated forward
links. Context aware Adaptive OR (CAOR) uses active suppression
mechanism to reduce packet duplication. The Context-aware OR
(COR) can provide efficient routing in mobile networks. By using
Cooperative Opportunistic Routing in Mobile Ad hoc Networks
(CORMAN), the problem of opportunistic data transfer can be
tackled. While comparing to all the protocols, COMO is the best as it
achieves social efficiency and prevents the selfish behavior of the
nodes.
Abstract: The end panels of a large rectangular industrial duct,
which experience significant internal pressures, also experience
considerable transverse shear due to transfer of gravity loads to the
supports. The current design practice of such thin plate panels for
shear load is based on methods used for the design of plate girder
webs. The structural arrangements, the loadings and the resulting
behavior associated with the industrial duct end panels are, however,
significantly different from those of the web of a plate girder. The
large aspect ratio of the end panels gives rise to multiple bands of
tension fields, whereas the plate girder web design is based on one
tension field. In addition to shear, the industrial end panels are
subjected to internal pressure which in turn produces significant
membrane action. This paper reports a study which was undertaken
to review the current industrial analysis and design methods and to
propose a comprehensive method of designing industrial duct end
panels for shear resistance. In this investigation, a nonlinear finite element model was
developed to simulate the behavior of industrial duct end panel, along
with the associated edge stiffeners, subjected to transverse shear and
internal pressures. The model considered the geometric imperfections
and constitutive relations for steels. Six scale independent
dimensionless parameters that govern the behavior of such end panel
were identified and were then used in a parametric study. It was
concluded that the plate slenderness dominates the shear strength of
stockier end panels, and whereas, both the plate slenderness and the
aspect ratio influence the shear strength of slender end panels. Based
on these studies, this paper proposes design aids for estimating the
shear strength of rectangular duct end panels.
Abstract: Mechanical behavior of 6082T6 aluminum is
investigated at different temperatures. The strain rate sensitivity is
investigated at different temperatures on the grain size variants. The
sensitivity of the measured grain size variants on 3-D grain is
discussed. It is shown that the strain rate sensitivities are negative for
the grain size variants during the deformation of nanostructured
materials. It is also observed that the strain rate sensitivities vary in
different ways with the equivalent radius, semi minor axis radius,
semi major axis radius and major axis radius. From the obtained
results, it is shown that the variation of strain rate sensitivity with
temperature suggests that the strain rate sensitivity at the low and the
high temperature ends of the 6082T6 aluminum range is different.
The obtained results revealed transition at different temperature from
negative strain rate sensitivity as temperature increased on the grain
size variants.
Abstract: The myocardium is composed of specialized muscle
which relies mainly on fatty acid and sugar metabolism and it is
widely contribute to the heart functioning. The changes of the cardiac
energy-producing system during heart failure have been proved using
autoradiography techniques. This study focused on evaluating sugar
and fatty acid metabolism in myocardium as cardiac energy getting
system using heart-accumulated radiopharmaceuticals. Two sets of
autoradiographs of heart cross sections of Lewis male rats were
analyzed and the time- accumulation curve obtained with use of the
MATLAB image processing software to evaluate fatty acid and sugar
metabolic functions.
Abstract: Gladiolus is an important cash crop and is grown
mainly for its elegant spikes. Traditionally the gladiolus corms are
planted manually which is very tedious, time consuming and labor
intensive operation. So far, there is no planter available for planting
of gladiolus corms. With a view to mechanize the planting operation
of this horticultural crop, a prototype of 4-row gladiolus planter was
developed and its performance was evaluated in-situ condition. Cupchain
type metering device was used to place each single gladiolus
corm in furrow at required spacing while planting. Three levels of
corm spacing viz 15, 20 and 25 cm and four levels of forward speed
viz 1.0, 1.5, 2.0 and 2.5 km/h was taken as evaluation parameter for
the planter. The performance indicators namely corm spacing in each
row, coefficient of uniformity, missing index, multiple index, quality
of feed index, number of corms per meter length, mechanical damage
to the corms etc. were determined during the field test. The data was
statistically analyzed using Completely Randomized Design (CRD)
for testing the significance of the parameters. The result indicated
that planter was able to drop the corms at required nominal spacing
with minor variations. The highest deviation from the mean corm
spacing was observed as 3.53 cm with maximum coefficient of
variation as 13.88%. The highest missing and quality of feed indexes
were observed as 6.33% and 97.45% respectively with no multiples.
The performance of the planter was observed better at lower forward
speed and wider corm spacing. The field capacity of the planter was
found as 0.103 ha/h with an observed field efficiency of 76.57%.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: Selenium is an-antioxidant which is important for
human health enters food chain through crops. In Kenya Zea mays is
consumed by 96% of population hence is a cheap and convenient
method to provide selenium to large number of population. Several
soil factors are known to have antagonistic effects on selenium
speciation hence the uptake by Zea mays. There are no studies in
Kenya that has been done to determine the effects of soil
characteristics (pH, Tcarbon, CEC, Eh) affect accumulation of
selenium in Zea mays grains in Maize Belt in Kenya. About 100 Zea mays grain samples together with 100 soil samples
were collected from the study site put in separate labeled Ziplocs and
were transported to laboratories at room temperature for analysis.
Maize grains were analyzed for selenium while soil samples were
analyzed for pH, Cat Ion Exchange Capacity, total carbon, and
electrical conductivity. The mean selenium in Zea mays grains varied from 1.82 ± 0.76
mg/Kg to 11±0.86 mg/Kg. There was no significant difference
between selenium levels between different grain batches {χ (Df =76)
= 26.04 P= 1.00} The pH levels varied from 5.43± 0.58 to 5.85±
0.32. No significant correlations between selenium in grains and soil
pH (Pearson’s correlations = - 0.143), and between selenium levels in
grains and the four (pH, Tcarbon, CEC, Eh) soil chemical
characteristics {F (4,91) = 0.721 p = 0.579} was observed. It can be concluded that the soil chemical characteristics in the
study site did not significantly affect the accumulation of native
selenium in Zea mays grains.
Abstract: The modelling of physical phenomena, such as the
earth’s free oscillations, the vibration of strings, the interaction of
atomic particles, or the steady state flow in a bar give rise to Sturm-
Liouville (SL) eigenvalue problems. The boundary applications of
some systems like the convection-diffusion equation, electromagnetic
and heat transfer problems requires the combination of Dirichlet and
Neumann boundary conditions. Hence, the incorporation of Robin
boundary condition in the analyses of Sturm-Liouville problem. This
paper deals with the computation of the eigenvalues and
eigenfunction of generalized Sturm-Liouville problems with Robin
boundary condition using the finite element method. Numerical
solution of classical Sturm–Liouville problem is presented. The
results show an agreement with the exact solution. High results
precision is achieved with higher number of elements.
Abstract: Wind energy is rapidly emerging as the primary
source of electricity in the Philippines, although developing an
accurate wind resource model is difficult. In this study, Weather
Research and Forecasting (WRF) Model, an open source mesoscale
Numerical Weather Prediction (NWP) model, was used to produce a
1-year atmospheric simulation with 4 km resolution on the Ilocos
Region of the Philippines. The WRF output (netCDF) extracts the
annual mean wind speed data using a Python-based Graphical User
Interface. Lastly, wind resource assessment was produced using a
GIS software. Results of the study showed that it is more flexible to
use Python scripts than using other post-processing tools in dealing
with netCDF files. Using WRF Model, Python, and Geographic
Information Systems, a reliable wind resource map is produced.
Abstract: As a result of the ambiguity and complexity
surrounding anaerobic digester foaming, efforts have been made by
various researchers to understand the process of anaerobic digester
foaming so as to proffer a solution that can be universally applied
rather than site specific. All attempts ranging from experimental
analysis to comparative review of other process has not fully
explained the conditions and process of foaming in anaerobic
digester. Studying the current available knowledge on foam
formation and relating it to anaerobic digester process and operating
condition, this piece of work presents a succinct and enhanced
understanding of foaming in anaerobic digesters as well as
introducing a simple method to identify the onset of anaerobic
digester foaming based on analysis of historical data from a field
scale system.
Abstract: A geoelectric survey was carried out in some parts of
Angwan Gwari, an outskirt of Lapai Local Government Area on
Niger State which belongs to the Nigerian Basement Complex, with
the aim of evaluating the soil corrosivity, aquifer transmissivity and
protective capacity of the area from which aquifer characterisation
was made. The G41 Resistivity Meter was employed to obtain fifteen
Schlumberger Vertical Electrical Sounding data along profiles in a
square grid network. The data were processed using interpex 1-D
sounding inversion software, which gives vertical electrical sounding
curves with layered model comprising of the apparent resistivities,
overburden thicknesses, and depth. This information was used to
evaluate longitudinal conductance and transmissivities of the layers.
The results show generally low resistivities across the survey area
and an average longitudinal conductance variation from
0.0237Siemens in VES 6 to 0.1261Siemens in VES 15 with almost
the entire area giving values less than 1.0 Siemens. The average
transmissivity values range from 96.45 Ω.m2 in VES 4 to 299070
Ω.m2 in VES 1. All but VES 4 and VES14 had an average
overburden greater than 400 Ω.m2, these results suggest that the
aquifers are highly permeable to fluid movement within, leading to
the possibility of enhanced migration and circulation of contaminants
in the groundwater system and that the area is generally corrosive.