Abstract: This paper studies the application of a variety of
sawdust materials in the production of lightweight insulating bricks.
First, the mineralogical and chemical composition of clays was determined. Next, ceramic bricks were fabricated with different
quantities of materials (3–6 and 9 wt. % for sawdust, 65 wt. % for grey clay, 24–27 and 30 wt. % for yellow clay and 2 wt% of tuff).
These bricks were fired at 800 and 950 °C. The effect of adding this sawdust on the technological behaviour of the brick was assessed by
drying and firing shrinkage, water absorption, porosity, bulk density
and compressive strength. The results have shown that the optimum
sintering temperature is 950 °C. Below this temperature, at 950 °C,
increased open porosity was observed, which decreased the compressive strength of the bricks. Based on the results obtained, the
optimum amounts of waste were 9 wt. % sawdust of eucalyptus, 24 wt. % shaping moisture and 1.6 particle size diameter. These percentages produced bricks whose mechanical properties were
suitable for use as secondary raw materials in ceramic brick
production.
Abstract: Safety Health and Environment Code of Practice (SHE
COP) was developed to help road transportation operators to manage
its operation in a systematic and safe manner. A study was conducted
to determine the effectiveness of SHE COP implementation during
non-OPS period. The objective of the study is to evaluate the
implementations of SHE COP among bus operators during wee hour
operations. The data was collected by completing a set of checklist
after observing the activities during pre departure, during the trip, and
upon arrival. The results show that there are seven widely practiced
SHE COP elements. 22% of the buses have average speed exceeding
the maximum permissible speed on the highways (90 km/h), with
13% of the buses were travelling at the speed of more than 100 km/h.
The statistical analysis shows that there is only one significant
association which relates speeding with prior presence of
enforcement officers.
Abstract: Turbulent forced convection flow in a 2-dimensional channel over periodic grooves is numerically investigated. Finite volume method is used to study the effect of turbulence model. The range of Reynolds number varied from 10000 to 30000 for the ribheight to channel-height ratio (B/H) of 2. The downstream wall is heated by a uniform heat flux while the upstream wall is insulated. The investigation is analyzed with different types of nanoparticles such as SiO2, Al2O3, and ZnO, with water as a base fluid are used. The volume fraction is varied from 1% to 4% and the nanoparticle diameter is utilized between 20nm to 50nm. The results revealed 114% heat transfer enhancement compared to the water in a grooved channel by using SiO2 nanoparticle with volume fraction and nanoparticle diameter of 4% and 20nm respectively.
Abstract: This paper describes the project and development of a
very low-cost and small electronic prototype, especially designed for
monitoring and controlling existing home automation alarm systems
(intruder, smoke, gas, flood, etc.), via TCP/IP, with a typical web
browser. Its use will allow home owners to be immediately alerted
and aware when an alarm event occurs, and being also able to
interact with their home automation alarm system, disarming, arming
and watching event alerts, with a personal wireless Wi-Fi PDA or
smartphone logged on to a dedicated predefined web page, and using
also a PC or Laptop.
Abstract: This paper is focused on issues of nonlinear dynamic process modeling and model-based predictive control of a fed-batch sugar crystallization process applying the concept of artificial neural networks as computational tools. The control objective is to force the operation into following optimal supersaturation trajectory. It is achieved by manipulating the feed flow rate of sugar liquor/syrup, considered as the control input. A feed forward neural network (FFNN) model of the process is first built as part of the controller structure to predict the process response over a specified (prediction) horizon. The predictions are supplied to an optimization procedure to determine the values of the control action over a specified (control) horizon that minimizes a predefined performance index. The control task is rather challenging due to the strong nonlinearity of the process dynamics and variations in the crystallization kinetics. However, the simulation results demonstrated smooth behavior of the control actions and satisfactory reference tracking.
Abstract: Technology transfer of renewable energy technologies is very often unsuccessful in the developing world. Aside from challenges that have social, economic, financial, institutional and environmental dimensions, technology transfer has generally been misunderstood, and largely seen as mere delivery of high tech equipment from developed to developing countries or within the developing world from R&D institutions to society. Technology transfer entails much more, including, but not limited to: entire systems and their component parts, know-how, goods and services, equipment, and organisational and managerial procedures. Means to facilitate the successful transfer of energy technologies, including the sharing of lessons are subsequently extremely important for developing countries as they grapple with increasing energy needs to sustain adequate economic growth and development. Improving the success of technology transfer is an ongoing process as more projects are implemented, new problems are encountered and new lessons are learnt. Renewable energy is also critical to improve the quality of lives of the majority of people in developing countries. In rural areas energy is primarily traditional biomass. The consumption activities typically occur in an inefficient manner, thus working against the notion of sustainable development. This paper explores the implementation of technology transfer in the developing world (sub-Saharan Africa). The focus is necessarily on RETs since most rural energy initiatives are RETs-based. Additionally, it aims to highlight some lessons drawn from the cited RE projects and identifies notable differences where energy technology transfer was judged to be successful. This is done through a literature review based on a selection of documented case studies which are judged against the definition provided for technology transfer. This paper also puts forth research recommendations that might contribute to improved technology transfer in the developing world. Key findings of this paper include: Technology transfer cannot be complete without satisfying pre-conditions such as: affordability, maintenance (and associated plans), knowledge and skills transfer, appropriate know how, ownership and commitment, ability to adapt technology, sound business principles such as financial viability and sustainability, project management, relevance and many others. It is also shown that lessons are learnt in both successful and unsuccessful projects.
Abstract: Deep cold rolling (DCR) is a cold working process, which easily produces a smooth and work-hardened surface by plastic deformation of surface irregularities. In the present study, the influence of main deep cold rolling process parameters on the surface roughness and the hardness of AISI 4140 steel were studied by using fractional factorial design of experiments. The assessment of the surface integrity aspects on work material was done, in terms of identifying the predominant factor amongst the selected parameters, their order of significance and setting the levels of the factors for minimizing surface roughness and/or maximizing surface hardness. It was found that the ball diameter, rolling force, initial surface roughness and number of tool passes are the most pronounced parameters, which have great effects on the work piece-s surface during the deep cold rolling process. A simple, inexpensive and newly developed DCR tool, with interchangeable collet for using different ball diameters, was used throughout the experimental work presented in this paper.
Abstract: Numerical calculations of flow around a square cylinder are presented using the multi-relaxation-time lattice Boltzmann method at Reynolds number 150. The effects of upstream locations, downstream locations and blockage are investigated systematically. A detail analysis are given in terms of time-trace analysis of drag and lift coefficients, power spectra analysis of lift coefficient, vorticity contours visualizations and phase diagrams. A number of physical quantities mean drag coefficient, drag coefficient, Strouhal number and root-mean-square values of drag and lift coefficients are calculated and compared with the well resolved experimental data and numerical results available in open literature. The results had shown that the upstream, downstream and height of the computational domain are at least 7.5, 37.5 and 12 diameters of the cylinder, respectively.
Abstract: Dried soy protein hydrolysate powder was added to
the burger in order to enhance the oxidative stability as well as
decreases the microbial spoilage. The soybean bioactive compounds
(soy protein hydrolysate) as antioxidant and antimicrobial were added
at level of 1, 2 and 3 %.Chemical analysis and physical properties
were affected by protein hydrolysate addition. The TBA values were
significantly affected (P < 0.05) by the storage period and the level of
soy protein hydrolysate. All the tested soybean protein hydrolysate
additives showed strong antioxidant properties. Samples of soybean
protein hydrolysate showed the lowest (P < 0.05) TBA values at each
time of storage.
The counts of all determined microbiological indicators were
significantly (P < 0.05) affected by the addition of the soybean
protein hydrolysate. Decreasing trends of different extent were also
observed in samples of the treatments for total viable counts,
Coliform, Staphylococcus aureus, yeast and molds. Storage period
was being significantly (P < 0.05) affected on microbial counts in all
samples Staphylococcus aureus were the most sensitive microbe
followed by Coliform group of the sample containing protein
hydrolysate, while molds and yeast count showed a decreasing trend
but not significant (P < 0.05) until the end of the storage period
compared with control sample. Sensory attributes were also
performed, added protein hydrolysate exhibits beany flavor which
was clear about samples of 3% protein hydrolysate.
Abstract: The main aim of this study was to examine whether
people understand indicative conditionals on the basis of syntactic
factors or on the basis of subjective conditional probability. The
second aim was to investigate whether the conditional probability of
q given p depends on the antecedent and consequent sizes or derives
from inductive processes leading to establish a link of plausible cooccurrence
between events semantically or experientially associated.
These competing hypotheses have been tested through a 3 x 2 x 2 x 2
mixed design involving the manipulation of four variables: type of
instructions (“Consider the following statement to be true", “Read the
following statement" and condition with no conditional statement);
antecedent size (high/low); consequent size (high/low); statement
probability (high/low). The first variable was between-subjects, the
others were within-subjects. The inferences investigated were Modus
Ponens and Modus Tollens. Ninety undergraduates of the Second
University of Naples, without any prior knowledge of logic or
conditional reasoning, participated in this study.
Results suggest that people understand conditionals in a syntactic
way rather than in a probabilistic way, even though the perception of
the conditional probability of q given p is at least partially involved in
the conditionals- comprehension. They also showed that, in presence
of a conditional syllogism, inferences are not affected by the
antecedent or consequent sizes. From a theoretical point of view these
findings suggest that it would be inappropriate to abandon the idea
that conditionals are naturally understood in a syntactic way for the
idea that they are understood in a probabilistic way.
Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: In this work, we first give in what fields Fp, the cubic
root of unity lies in F*p, in Qp and in K*p where Qp and K*p denote
the sets of quadratic and non-zero cubic residues modulo p. Then we
use these to obtain some results on the classification of the Bachet
elliptic curves y2 ≡ x3 +a3 modulo p, for p ≡ 1 (mod 6) is prime.
Abstract: This paper presents a low-voltage low-power differential linear transconductor with near rail-to-rail input swing. Based on the current-mirror OTA topology, the proposed transconductor combines the Flipped Voltage Follower (FVF) technique to linearize the transconductor behavior that leads to class- AB linear operation and the virtual transistor technique to lower the effective threshold voltages of the transistors which offers an advantage in terms of low supply requirement. Design of the OTA has been discussed. It operates at supply voltages of about ±0.8V. Simulation results for 0.18μm TSMC CMOS technology show a good input range of 1Vpp with a high DC gain of 81.53dB and a total harmonic distortion of -40dB at 1MHz for an input of 1Vpp. The main aim of this paper is to present and compare new OTA design with high transconductance, which has a potential to be used in low voltage applications.
Abstract: The aim of this work is to analyze a viscous flow in
the axisymmetric nozzle taken into account the mesh size both in the
free stream and into the boundary layer. The resolution of the Navier-
Stokes equations is realized by using the finite volume method to
determine the supersonic flow parameters at the exit of convergingdiverging
nozzle. The numerical technique uses the Flux Vector
Splitting method of Van Leer. Here, adequate time stepping
parameter, along with CFL coefficient and mesh size level is selected
to ensure numerical convergence. The effect of the boundary layer
thickness is significant at the exit of the nozzle. The best solution is
obtained with using a very fine grid, especially near the wall, where
we have a strong variation of velocity, temperature and shear stress.
This study enabled us to confirm that the determination of boundary
layer thickness can be obtained only if the size of the mesh is lower
than a certain value limits given by our calculations.
Abstract: This paper addresses the problem of forbidden states in
non safe Petri Nets. In the system, for preventing it from entering the
forbidden states, some linear constraints can be assigned to them.
Then these constraints can be enforced on the system using control
places. But when the number of constraints in the system is large, a
large number of control places must be added to the model of system.
This concept complicates the model of system. There are some
methods for reducing the number of constraints in safe Petri Nets.
But there is no a systematic method for non safe Petri Nets. In this
paper we propose a method for reducing the number of constraints in
non safe Petri Nets which is based on solving an integer linear
programming problem.
Abstract: This article deals with the conceptual modeling under uncertainty. First, the division of information systems with their definition will be described, focusing on those where the construction of a conceptual model is suitable for the design of future information system database. Furthermore, the disadvantages of the traditional approach in creating a conceptual model and database design will be analyzed. A comprehensive methodology for the creation of a conceptual model based on analysis of client requirements and the selection of a suitable domain model is proposed here. This article presents the expert system used for the construction of a conceptual model and is a suitable tool for database designers to create a conceptual model.
Abstract: Human always tried to create a suitable situation for their life according to environmental conditions. In fact, geography has an important role in the shape of our living area. Iran also as a four-season country has different climate type: hot and humid, hot and dry, mid and humid, and cold; therefore, we can find different architecture styles in Iran. Gilan-s traditional architecture is a suitable sample of sustainable construction in Iran. Because the main factors of every dwelling are the climatic, social, economic and cultural effects which demonstrate the interaction between environment and people settlement. This paper was determined the interaction between environmental factors and the rural dwellings in the Gilan province. Also, traditional village (city) of Masouleh as a rare sample of rural and sustainable architecture was introduced.
Abstract: The evolution of current modeling specifications gives rise to the problem of generating automated test cases from a variety of application tools. Past endeavours on behavioural testing of UML statecharts have not systematically leveraged the potential of existing graph theory for testing of objects. Therefore there exists a need for a simple, tool-independent, and effective method for automatic test generation. An architecture, codenamed ACUTE-J (Automated stateChart Unit Testing Engine for Java), for automating the unit test generation process is presented. A sequential approach for converting UML statechart diagrams to JUnit test classes is described, with the application of existing graph theory. Research byproducts such as a universal XML Schema and API for statechart-driven testing are also proposed. The result from a Java implementation of ACUTE-J is discussed in brief. The Chinese Postman algorithm is utilised as an illustration for a run-through of the ACUTE-J architecture.
Abstract: The aim of this paper is to provide a better
understanding of the implementation of Project Management
practices by UiTM contractors to ensure project success. A
questionnaire survey was administered to 120 UiTM contractors in
Malaysia. The purpose of this method was to gather information on
the contractors- project background and project management skills. It
was found that all of the contractors had basic knowledge and
understanding of project management skills. It is suggested that a
reasonable project plan and an appropriate organizational structure
are influential factors for project success. It is recommended that the
contractors need to have an effective program of work and up to date
information system are emphasized.
Abstract: In order to study of hydropriming and halopriming on
germination and early growth stage of wheat (Triticum aestivum) an
experiment was carried out in laboratory of the Department of
Agronomy and Plant breeding, Shahrood University of Technology.
Seed treatments consisted of T1: control (untreated seeds), T2:
soaking in distilled water for 18 h (hydropriming). T3: soaking in -
1.2 MPa solution of CaSO4 for 36 h (halopriming). Germination and
early seedling growth were studied using distilled water (control) and
under osmotic potentials of -0.4, -0.8 and -1.2 MPa for NaCl and
polyethylene glycol (PEG 6000), respectively. Results showed that
Hydroprimed seeds achieved maximum germination seedling dry
weight, especially during the higher osmotic potentials. Minimum
germination was recorded at untreated seeds (control) followed by
osmopriming. Under high osmotic potentials, hydroprimed seeds had
higher GI (germination index) as compared to haloprimed or
untreated seeds. Interaction effect of seed treatment and osmotic
potential significantly affected the seedling vigour index (SVI).