Abstract: The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.
Abstract: Surplus electricity can be converted into potential energy via pumped hydroelectric storage for future usage. Similarly, thermo-electric energy storage (TEES) uses heat pumps equipped with thermal storage to convert electrical energy into thermal energy; the stored energy is then converted back into electrical energy when necessary using a heat engine. The greatest advantage of this method is that, unlike pumped hydroelectric storage and compressed air energy storage, TEES is not restricted by geographical constraints. In this study, performance variation of the TEES according to the changes in cold-side storage temperature was investigated by simulation method.
Abstract: In this paper, we employ a directed hypergraph model
to investigate the extent to which environmental variability influences
the set of available biochemical reactions within a living cell.
Such an approach avoids the limitations of the usual complex
network formalism by allowing for the multilateral relationships (i.e.
connections involving more than two nodes) that naturally occur
within many biological processes. More specifically, we extend the
concept of network reciprocity to complex hyper-networks, thus
enabling us to characterise a network in terms of the existence
of mutual hyper-connections, which may be considered a proxy
for metabolic network complexity. To demonstrate these ideas, we
study 115 metabolic hyper-networks of bacteria, each of which
can be classified into one of 6 increasingly varied habitats.
In particular, we found that reciprocity increases significantly
with increased environmental variability, supporting the view that
organism adaptability leads to increased complexities in the resultant
biochemical networks.
Abstract: The purposes of the study are to investigate the problems that the translators encountered when translating English idioms into Thai and study the strategies they applied in solving the problems. The original English version and the Thai translated version of each of two works of fiction were purposively selected for the study. The first was Mr. Maybe, written by Jane Green and translated by Montharat Songphao. The second was The Trials of Tiffany Trott, written by Isabel Wolff and translated by Jitraporn Notoda. Thirty idioms of two translated works of fiction were, then, analyzed. Questionnaires and interviews with the translators of each novel were conducted to obtain the best possible information.
The results indicated that the only type of problem that occurred was cultural problems, and these were solved differently by the two translators
Abstract: In recent years many finite elements have been
developed for plate bending analysis. The formulated elements are
based on the strain based approach. This approach leads to the
representation of the displacements by higher order polynomial terms
without the need for the introduction of additional internal and
unnecessary degrees of freedom. Good convergence can also be
obtained when the results are compared with those obtained from the
corresponding displacement based elements, having the same total
number of degrees of freedom. Furthermore, the plate bending
elements are free from any shear locking since they converge to the
Kirchhoff solution for thin plates contrarily for the corresponding
displacement based elements. In this paper the efficiency of the strain
based approach compared to well known displacement formulation is
presented. The results obtained by a new formulated plate bending
element based on the strain approach and Kirchhoff theory are
compared with some others elements. The good convergence of the
new formulated element is confirmed.
Abstract: The analysis and design of thin shell structures is a topic of interest in a variety of engineering applications. In structural mechanics problems the analyst seeks to determine the distribution of stresses throughout the structure to be designed. It is also necessary to calculate the displacements of certain points of the structure to ensure that specified allowable values are not exceeded. In this paper a comparative study between displacement and strain based finite elements applied to the analysis of some thin shell structures is presented. The results obtained from some examples show the efficiency and the performance of the strain based approach compared to the well known displacement formulation.
Abstract: The work presented in this paper was performed for a workstation of an assembly section in a company that manufactures radio modules and air conditioning for cars. After performing a workstation analysis and a questionnaire to the operators it was possible to understand the need to investigate the risk of musculoskeletal disorders originated from both the handling of loads as the incorrect dimensioning of the workstation. Regarding the handling of loads the NIOSH Equation was used and it was verified that there was no risk of musculoskeletal disorders. As the operators expressed their lack of satisfaction regarding back pains due to posture adopted they were established the appropriate dimensions (to satisfy 97.5% of the population and using the table of anthropometric data of the Portuguese population) for the workstation and it was proposed the availability of a chair for the workers.
Abstract: Sustainable urban waterfront development is one of the
most interesting phenomena of urban renewal in the last decades.
However, there are still many cities whose visual image is
compromised due to the lack of a sustainable urban waterfront
development, which consequently affects the place of those cities
globally. This paper aims to reimagine the role of waterfront areas in
city design, with a particular focus on Egypt, so that they provide
attractive, sustainable urban environments while promoting the
continued aesthetic development of the city overall. This aim will be
achieved by determining the main principles of a sustainable urban
waterfront and its applications. This paper concentrates on
sustainability assessment rating systems. A number of international
case-studies, wherein a city has applied the basic principles for a
sustainable urban waterfront and have made use of sustainability
assessment rating systems, have been selected as examples which can
be applied to the urban waterfronts in Egypt. This paper establishes the
importance of developing the design of urban environments in Egypt,
as well as identifying the methods of sustainability application for
urban waterfronts.
Abstract: In this article the problem of distributional moments estimation is considered. The new approach of moments estimation based on usage of the characteristic function is proposed. By statistical simulation technique author shows that new approach has some robust properties. For calculation of the derivatives of characteristic function there is used numerical differentiation. Obtained results confirmed that author’s idea has a certain working efficiency and it can be recommended for any statistical applications.
Abstract: In this paper, for detection of inclined eccentricity in an induction motor, time–frequency analysis of the stator startup current is carried out. For this purpose, the discrete wavelet transform is used. Data are obtained from simulations, using winding function approach. The results show the validity of the approach for detecting the fault and discriminating with respect to other faults.
Abstract: The Ballast Water Convention requires less than 5% of the world tonnage for ratification. Consequently, ships will have to comply with the requirements. Compliance evaluation and enforcement will become mandatory. Ship owners have to invest in treatment systems and shipboard personnel have to operate them and ensure compliance. The monitoring and enforcement will be the responsibilities of the Administrations. Herein, a review of the current status of the Ballast Water Management and the issues faced by these are projected. Issues range from efficacy and economics of the treatment systems to sampling and testing. Health issues of chemical systems, paucity of data for decision support etc., are other issues. It is emphasized that management of ballast water must be extended to ashore and sustainable solutions must be researched upon. An exemplar treatment system based on ship’s waste heat is also suggested.
Abstract: As a developing country, The Kingdom of Saudi Arabia (KSA) needs to make the best possible use of its workforce for social and economic reasons. The workforce is diverse, calling for appropriate diversity management (DM). The thesis focuses on the banking sector in KSA. To date, there have been no studies on DM in the banking sector in this country. Many organizations have introduced specific policies and programmes to improve the recruitment, inclusion, promotion, and retention of diverse employees, in addition to the legal requirements existing in many countries. However, Western-centric models of DM may not be applicable, at least not in their entirety, in other regions.
The aim of the study is to devise a framework for understanding gender, age and disability DM in the banking sector in KSA in order to enhance DM in this sector. A sample of 24 managers, 2 from each of the 12 banks, was interviewed to obtain their views on DM in the banking sector in KSA. Thematic analysis was used to analyze the data. These themes were used to develop the questionnaire, which was administered to 10 managers in each of the 12 banks. After analysis of these data, and completion of the study, the research will make a theoretical contribution to the knowledge on DM and a practical contribution to the management of diversity in Saudi banks. This paper concerns a work in progress.
Abstract: Accurate Short Term Load Forecasting (STLF) is essential for a variety of decision making processes. However, forecasting accuracy can drop due to the presence of uncertainty in the operation of energy systems or unexpected behavior of exogenous variables. Interval Type 2 Fuzzy Logic System (IT2 FLS), with additional degrees of freedom, gives an excellent tool for handling uncertainties and it improved the prediction accuracy. The training data used in this study covers the period from January 1, 2012 to February 1, 2012 for winter season and the period from July 1, 2012 to August 1, 2012 for summer season. The actual load forecasting period starts from January 22, till 28, 2012 for winter model and from July 22 till 28, 2012 for summer model. The real data for Iraqi power system which belongs to the Ministry of Electricity.
Abstract: In this study, Electrical Discharge Machining (EDM) is used to modify the surface of high carbon steel En31 with the help of tool electrode (Copper-Chromium-Nickel) manufactured by powder metallurgy (PM) process. The effect of EDM on surface roughness during surface alloying is studied. Taguchi’s Design of experiment (DOE) and L18 orthogonal array is used to find the best level of input parameters in order to achieve high surface finish. Six input parameters are considered and their percentage contribution towards surface roughness is investigated by analysis of variances (ANOVA). Experimental results show that an hard alloyed surface (1.21% carbon, 2.14% chromium and 1.38% nickel) with surface roughness of 3.19µm can be generated using EDM with PM tool. Additionally, techniques like Scanning Electron Microscope (SEM) and Energy Dispersive Spectroscopy (EDS) are used to analyze the machined surface and EDMed layer composition, respectively. The increase in machined surface micro-hardness (101%) may be related to the formation of carbides containing chromium.
Abstract: In this paper, fractional order feedback control of a ball
beam model is investigated. The ball beam model is a particular
example of the double Integrator system having strongly nonlinear
characteristics and unstable dynamics which make the control of
such system a challenging task. Most of the work in fractional order
control systems are in theoretical nature and controller design and its
implementation in practice is very small. In this work, a successful
attempt has been made to design a fractional order PIλDμcontroller
for a benchmark laboratory ball and beam model. Better performance
can be achieved using a fractional order PID controller and it is
demonstrated through simulations results with a comparison to the
classic PID controller.
Abstract: Combustion phenomenon will be accomplished
effectively by the development of low emission combustor. One of the
significant factors influencing the entire Combustion process is the
mixing between a swirling angular jet (Primary Air) and the
non-swirling inner jet (fuel). To study this fundamental flow, the
chamber had to be designed in such a manner that the combustion
process to sustain itself in a continuous manner and the temperature of
the products is sufficiently below the maximum working temperature
in the turbine. This study is used to develop the effective combustion
with low unburned combustion products by adopting the concept of
high swirl flow and motility of holes in the secondary chamber. The
proper selection of a swirler is needed to reduce emission which can be
concluded from the emission of Nox and CO2. The capture of CO2 is
necessary to mitigate CO2 emissions from natural gas. Thus the
suppression of unburned gases is a meaningful objective for the
development of high performance combustor without affecting turbine
blade temperature.
Abstract: Solid lipid nanoparticles (SLNs) have gained great attention for the topical treatment of skin associated fungal infection as they facilitate the skin penetration of loaded drugs. Our work deals with the preparation of nystatin loaded solid lipid nanoparticles (NystSLNs) using the hot homogenization and ultrasonication method. The prepared NystSLNs were characterized in terms of entrapment efficiency, particle size, zeta potential, transmission electron microscopy, differential scanning calorimetry, rheological behavior and in vitro drug release. A stability study for 6 months was performed. A microbiological study was conducted in male rats infected with Candida albicans, by counting the colonies and examining the histopathological changes induced on the skin of infected rats. The results showed that SLNs dispersions are spherical in shape with particle size ranging from 83.26±11.33 to 955.04±1.09 nm. The entrapment efficiencies are ranging from 19.73±1.21 to 72.46±0.66% with zeta potential ranging from -18.9 to -38.8 mV and shear-thinning rheological Behavior. The stability studies done for 6 months showed that nystatin (Nyst) is a good candidate for topical SLN formulations. A least number of colony forming unit/ ml (cfu/ml) was recorded for the selected NystSLN compared to the drug solution and the commercial Nystatin® cream present in the market. It can be fulfilled from this work that SLNs provide a good skin targeting effect and may represent promising carrier for topical delivery of Nyst offering the sustained release and maintaining the localized effect, resulting in an effective treatment of cutaneous fungal infection.
Abstract: The use of biodiesel in conventional diesel engines results in substantial reduction of unburned hydrocarbon, carbon monoxide and particulate matters. The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio engine when fueled with Karanja (Pongamia) methyl ester and its 10-50 % blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of karanja methyl ester as a biofuel has been established in this study. The useful brake power obtained is similar to diesel fuel for all loads. Experiment has been conducted at a fixed engine speed of 1500 rpm, variable load and at compression ratios of 17.5:1 and 18.5:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for pongamia oil methyl ester when compared to that of diesel. The brake thermal efficiency for pongamia oil methyl ester blends and diesel has been calculated and the blend B20 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions. PME as an oxygenated fuel generated more complete combustion, which means increased torque and power. This is also supported with higher thermal efficiencies of the PME blends. NOx is slightly increased due to the higher combustion temperature and the presence of fuel oxygen with the blend at full load. PME as a new Biodiesel and its blends can be used in diesel engines without any engine modification.
Abstract: Chittagong is the commercial capital of Bangladesh.
Here Agrabad is one of the most commercial activity centers of
Chittagong. Due to many light industry and commercial land use,
Agrabad to CEPZ road at Agrabad is the only major road of
Chittagong port city which encompasses a huge number of vehicles
every day. It has many junctions which distribute traffic flow in
different roads. In these junctions vehicles gather at some conflict
point to create traffic jam and make the performance of the road
downward. This study is parallel focused on the existing level of
service with traffic volume, capacity, and speed by traffic survey.
After all of these analyses the performance of the road is determined
with finding the factors that influences the performance.
Abstract: Generally, distributed generation units refer to small-scale electric power generators that produce electricity at a site close to the customer or an electric distribution system (in parallel mode). From the customers’ point of view, a potentially lower cost, higher service reliability, high power quality, increased energy efficiency, and energy independence can be the key points of a proper DG unit. Moreover, the use of renewable types of distributed generations such as wind, photovoltaic, geothermal or hydroelectric power can also provide significant environmental benefits. Therefore, it is of crucial importance to study their impacts on the distribution networks. A marked increase in Distributed Generation (DG), associated with medium voltage distribution networks, may be expected. Nowadays, distribution networks are planned for unidirectional power flows that are peculiar to passive systems, and voltage control is carried out exclusively by varying the tap position of the HV/MV transformer. This paper will compare different DG control methods and possible network reconfiguration aimed at assessing their effect on voltage profiles.