Abstract: Imaging is defined as the process of obtaining
geometric images either two dimensional or three dimensional by scanning or digitizing the existing objects or products. In this research, it applied to retrieve 3D information of the human skin
surface in medical application. This research focuses on analyzing
and determining volume of leg ulcers using imaging devices. Volume
determination is one of the important criteria in clinical assessment of leg ulcer. The volume and size of the leg ulcer wound will give the
indication on responding to treatment whether healing or worsening.
Different imaging techniques are expected to give different result (and accuracies) in generating data and images. Midpoint projection
algorithm was used to reconstruct the cavity to solid model and compute the volume. Misinterpretation of the results can affect the
treatment efficacy. The objectives of this paper is to compare the
accuracy between two 3D data acquisition method, which is laser
triangulation and structured light methods, It was shown that using models with known volume, that structured-light-based 3D technique
produces better accuracy compared with laser triangulation data
acquisition method for leg ulcer volume determination.
Abstract: Mature landfill leachates contain some macromolecular organic substances that are resistant to biological degradation. Recently, Fenton-s oxidation has been investigated for chemical treatment or pre-treatment of mature landfill leachates. The aim of this study was to reduce the recalcitrant organic load still remaining after the complete treatment of a mature landfill leachate by Fenton-s oxidation post-treatment. The effect of various parameters such as H2O2 to Fe2+ molar ratio, dosage of Fe2+ reagent, initial pH, reaction time and initial chemical oxygen demand (COD) strength, that have an important role on the oxidation, was analysed. A molar ratio H2O2/Fe2+ = 3, a Fe2+ dosage of 4 mmol·L-1, pH 3, and a reaction time of 40 min were found to achieve better oxidation performances. At these favorable conditions, COD removal efficiency was 60.9% and 31.1% for initial COD of 93 and 743 mg·L-1 respectively (diluted and non diluted leachate). Fenton-s oxidation also presented good results for color removal. In spite of being extremely difficult to treat this leachate, the above results seem rather encouraging on the application of Fenton-s oxidation.
Abstract: The cardiovascular system has become the most
important subject of clinical research, particularly measurement of
arterial blood flow. Therefore correct determination of arterial
diameter is crucial. We propose a novel, semi-automatic method for
artery lumen detection. The method is based on Gaussian probability
function. Usability of our proposed method was assessed by
analyzing ultrasound B-mode CFA video sequences acquired from
eleven healthy volunteers. The correlation coefficient between the
manual and semi-automatic measurement of arterial diameter was
0.996. Our proposed method for detecting artery boundary is novel
and accurate enough for the measurement of artery diameter.
Abstract: Influence diagrams (IDs) are one of the most commonly used graphical decision models for reasoning under uncertainty. The quantification of IDs which consists in defining conditional probabilities for chance nodes and utility functions for value nodes is not always obvious. In fact, decision makers cannot always provide exact numerical values and in some cases, it is more easier for them to specify qualitative preference orders. This work proposes an adaptation of standard IDs to the qualitative framework based on possibility theory.
Abstract: Evolutionary robotics is concerned with the design of
intelligent systems with life-like properties by means of simulated
evolution. Approaches in evolutionary robotics can be categorized
according to the control structures that represent the behavior and the
parameters of the controller that undergo adaptation. The basic idea
is to automatically synthesize behaviors that enable the robot to
perform useful tasks in complex environments. The evolutionary
algorithm searches through the space of parameterized controllers
that map sensory perceptions to control actions, thus realizing a
specific robotic behavior. Further, the evolutionary algorithm
maintains and improves a population of candidate behaviors by
means of selection, recombination and mutation. A fitness function
evaluates the performance of the resulting behavior according to the
robot-s task or mission. In this paper, the focus is in the use of
genetic algorithms to solve a multi-objective optimization problem
representing robot behaviors; in particular, the A-Compander Law is
employed in selecting the weight of each objective during the
optimization process. Results using an adaptive fitness function show
that this approach can efficiently react to complex tasks under
variable environments.
Abstract: The environmental factors such as temperature and
relative humidity are very contribute to the effect of comfort, health,
performance and worker productivity. To ensure an ergonomics work
environment, it is possible to require a specific attention especially in
industries. The aim of this study is to show the effect of temperature
and relative humidity on worker productivity in automotive industry
by taking a workstation in an automotive plant as the location to
conduct the study. From the analysis of the data, there were
relationship between temperature and relative humidity on worker
productivity. Mathematical equation to represent the relationship
between temperatures and relative humidity on the production rate is
modelled. From the equation model, the production rate for the
workstation can be predicted base on the value of temperature and
relative humidity.
Abstract: Field experiment was conducted to investigate the combine use of animal manure and inorganic fertilizer on growth and yield performance of vegetable cowpea. The experiment was laid out in a Randomized Complete Block Design (RCBD) with seven treatments. Poultry manure, cattle manure and goat manure were evaluated with recommended level of inorganic fertilizer for vegetable cowpea. The highest crop yield was obtained by the application of poultry manure combined with the recommended level of inorganic fertilizer. The lowest yield was obtained by the application of goat manure only. In addition, the results revealed that the goat manure and cattle manure were inferior to poultry manure as a source of organic manure for vegetable cowpea cultivation. The animal manure combine with chemical fertilizer gave a higher yield when compared to the sole application of animal manure. The soil analysis showed that the nitrogen content and phosphorus content of poultry manure treated plots were higher than other treatments tested. But potassium content was higher in goat manure treated plots. The results further revealed that the poultry manure has a beneficial effect on crop growth and yield compared with other treatments. Therefore, the combined use of poultry manure with inorganic fertilizer application has been recognized as the most suitable way of ensuring high crop yield.
Abstract: Self-sensing estimates the air gap within an electro
magnetic path by analyzing the bearing coil current and/or voltage
waveform. The self-sensing concept presented in this paper has been
developed within the research project “Active Magnetic Bearings
with Supreme Reliability" and is used for position sensor fault
detection.
Within this new concept gap calculation is carried out by an alldigital
analysis of the digitized coil current and voltage waveform.
For analysis those time periods within the PWM period are used,
which give the best results. Additionally, the concept allows the
digital compensation of nonlinearities, for example magnetic
saturation, without degrading signal quality. This increases the
accuracy and robustness of the air gap estimation and additionally
reduces phase delays.
Beneath an overview about the developed concept first
measurement results are presented which show the potential of this
all-digital self-sensing concept.
Abstract: This paper analyses the torsional efforts in gas turbine-generator shafts caused by high speed automatic reclosing of transmission lines. This issue is especially important for cases of three phase short circuit and unsuccessful reclosure of lines in the vicinity of the thermal plant. The analysis was carried out for the thermal plant TERMOPERNAMBUCO located on Northeast region of Brazil. It is shown that stress level caused by lines unsuccessful reclosing can be several times higher than terminal three-phase short circuit. Simulations were carried out with detailed shaft torsional model provided by machine manufacturer and with the “Alternative Transient Program – ATP" program [1]. Unsuccessful three phase reclosing for selected lines in the area closed to the plant indicated most critical cases. Also, reclosing first the terminal next to the gas turbine gererator will lead also to the most critical condition. Considering that the values of transient torques are very sensible to the instant of reclosing, simulation of unsuccessful reclosing with statistics ATP switch were carried out for determination of most critical transient torques for each section of the generator turbine shaft.
Abstract: The aim of this study was to determine noise level of
six different types of machines in printing companies in Novi Sad.
The A-weighted levels on Leq, Lmax and Lmin Sound Pressure Level
(SPL) in dBA were measured. It was found that the folders, offset
printing presses and binding machines are the predominant noise
sources. The noise levels produced by 12 of 38 machines exceed the
limiting threshold level of 85 dBA, tolerated by law. Since it was
determined that the average noise level for folders (87.7 dB) exceeds
the permitted value the octave analysis of noise was performed.
Abstract: This paper develops a critical perspective on using
culture and creativity as tools for urban regeneration. Following a
brief assessment of the evolution of cultural policy in recent decades
and different urban regeneration scheme, the concepts of creativity
and creative cities are discussed. This is followed by an attempt to
clarify the relationship between the concepts of creativity and culture.
A more detailed critique of cultural and creative initiatives in Serbian
cities is then undertaken. These attempts show that the potential for
development of urban regeneration driven by culture and creativity
exist. But, these initiatives failed to produce adequate results because
they did not take root as a comprehensive urban regeneration
strategy, therefore, recommendations for further development are
offered.
Abstract: The interrelationship between international stock
markets has been a key study area among the financial market
researchers for international portfolio management and risk
measurement. The characteristics of security returns and their
dynamics play a vital role in the financial market theory. This study
is an attempt to find out the dynamic linkages among the equity
market of USA and emerging markets of Pakistan and India using
daily data covering the period of January 2003–December 2009. The
study utilizes Johansen (Journal of Economic Dynamics and Control,
12, 1988) and Johansen and Juselius (Oxford Bulletin of Economics
and Statistics, 52, 1990) cointegration procedure for long run
relationship and Granger-causality tests based on Toda and
Yamamoto (Journal of Econometrics, 66, 1995) methodology.
No cointegration was found among stock markets of USA, Pakistan
and India, while Granger-causality test showed the evidence of
unidirectional causality running from New York stock exchange to
Bombay and Karachi stock exchanges.
Abstract: Finding synchronizing sequences for the finite automata is a very important problem in many practical applications (part orienters in industry, reset problem in biocomputing theory, network issues etc). Problem of finding the shortest synchronizing sequence is NP-hard, so polynomial algorithms probably can work only as heuristic ones. In this paper we propose two versions of polynomial algorithms which work better than well-known Eppstein-s Greedy and Cycle algorithms.
Abstract: The paper presents the applications of artificial
intelligence technique called adaptive tabu search to design the
controller of a buck converter. The averaging model derived from the
DQ and generalized state-space averaging methods is applied to
simulate the system during a searching process. The simulations
using such averaging model require the faster computational time
compared with that of the full topology model from the software
packages. The reported model is suitable for the work in the paper in
which the repeating calculation is needed for searching the best
solution. The results will show that the proposed design technique
can provide the better output waveforms compared with those
designed from the classical method.
Abstract: Complex statistical analysis of stresses in concrete
slab of the real type of rigid pavement is performed. The
computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method
that respects the structural nonlinearity, enables to model different arrangement of joints, and the entire model can be loaded by the
thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with help of special
contact elements. Four concrete slabs separated by transverse and
longitudinal joints and the additional subgrade layers and soil to the depth of about 3m are modeled. The thickness of individual layers,
physical and mechanical properties of materials, characteristics of
joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique
Updated Latin Hypercube Sampling with 20 simulations is used for statistical analysis. As results, the estimates of basic statistics of the
principal stresses s1 and s3 in 53 points on the upper and lower surface of the slabs are obtained.
Abstract: The objective was to determine the single gene and
interaction effect of composite genotype of beta-kappa casein and
DGAT1 gene on milk yield (MY) and milk composition, content of
milk fat (%FAT), milk protein (%PRO), solid not fat (%SNF), and
total solid (%TS) in crossbred Holstein cows. Two hundred and
thirty- one cows were genotyped with PCR-RFLP for DGAT1 and
composite genotype data of beta-kappa casein from previous work
were used. Two model, (1), and (2), was used to estimate single gene
effect, and interaction effect on the traits, respectively. The
significance of interaction effects on all traits were detected. Most
traits have consistent pattern of significant when model (1), and (2)
were compared, except the effect of composite genotype of betakappa
casein on %FAT, and the effect of DGAT1 on MY, which the
significant difference was detected in only model (1).The results
suggested that when the optimum of all traits was necessary,
interaction effect should be concerned.
Abstract: Mixed Model Production is the practice of assembling
several distinct and different models of a product on the same
assembly line without changeovers and then sequencing those models
in a way that smoothes the demand for upstream components. In this
paper, we consider an objective function which minimizes total
stoppage time and total idle time and it is presented sequence
dependent set up time. Many studies have been done on the mixed
model assembly lines. But in this paper we specifically focused on
reducing the idle times. This is possible through various help policies.
For improving the solutions, some cases developed and about 40 tests
problem was considered. We use scatter search for optimization and
for showing the efficiency of our algorithm, experimental results
shows behavior of method. Scatter search and help policies can
produce high quality answers, so it has been used in this paper.
Abstract: Tablet computers and Multifunctional Hardcopy Devices (MHDs) are common devices in daily life. Though, many scientific studies have not been published. The tablet computers are straightforward to use whereas the MHDs are comparatively difficult to use. Thus, to assist different levels of users, we propose combining these two devices to achieve straightforward intelligent user interface (UI) and versatile What You See Is What You Get (WYSIWYG) document management and production. Our approach to this issue is to design an intelligent user dependent UI for a MHD applying a tablet computer. Furthermore, we propose hardware interconnection and versatile intelligent software between these two devices. In this study, we first provide a state-of-the-art survey on MHDs and tablet computers, and their interconnections. Secondly we provide a comparative UI survey on two state-of-the-art MHDs with a proposal of a novel UI for the MHDs using Jakob Nielsen-s Ten Usability Heuristics Evaluation.
Abstract: The aim of this paper is to identify the most suitable
model for churn prediction based on three different techniques. The
paper identifies the variables that affect churn in reverence of
customer complaints data and provides a comparative analysis of
neural networks, regression trees and regression in their capabilities
of predicting customer churn.
Abstract: The adoption of building information modeling (BIM)
is increasing in the construction industry. However, quantity
surveyors are slow in adoption compared to other professions due to
lack of awareness of the BIM’s potential in their profession. It is still
unclear on how BIM application can enhance quantity surveyors’
work performance and project performance. The aim of this research
is to identify the capabilities of BIM in quantity surveying practices
and examine the relationship between BIM capabilities and project
performance. Questionnaire survey and interviews were adopted for
data collection. Literature reviews identified there are eleven BIM
capabilities in quantity surveying practice. Questionnaire results
showed that there are several BIM capabilities significantly
correlated with project performance in time, cost and quality aspects
and the results were validated through interviews. These findings
show that BIM has the capabilities to enhance quantity surveyors’
performances and subsequently improved project performance.