Abstract: The paper presents coupled electromagnetic and
thermal field analysis of busbar system (of rectangular cross-section
geometry) submitted to short circuit conditions. The laboratory model
was validated against both analytical solution and experimental
observations. The considered problem required the computation of
the detailed distribution of the power losses and the heat transfer
modes. In this electromagnetic and thermal analysis, different
definitions of electric busbar heating were considered and compared.
The busbar system is a three phase one and consists of aluminum,
painted aluminum and copper busbar. The solution to the coupled
field problem is obtained using the finite element method and the
QuickField™ program. Experiments have been carried out using two
different approaches and compared with computed results.
Abstract: Tribological behavior and wear regimes of ascast
and heattreted Al-Cu-Mg matrix composites containing SiC
particles were studied using a pin-on-disc wear testing apparatus
against an EN32 steel counterface giving emphasis on wear rate as
a function of applied pressures (0.2, 0.6, 1.0 and 1.4 MPa) at
different sliding distances (1000, 2000, 3000, 4000 and 5000
meters) and at a fixed sliding speed of 3.35m/s. The results showed
that the composite exhibited lower wear rate than that of the matrix
alloy and the wear rate of the composites is noted to be invariant to
the sliding distance and is reducing by heat treatment. Wear
regimes such as low, mild and severe wear were observed as per the
Archard-s wear calculations. It is very interesting to note that the
mild wear is almost constant in all the wear regimes.
Abstract: Recent years, adaptive pushover methods have been
developed for seismic analysis of structures. Herein, the accuracy of
the displacement-based adaptive pushover (DAP) method, which is
introduced by Antoniou and Pinho [2004], is evaluated for Irregular
buildings. The results are compared to the force-based procedure.
Both concrete and steel frame structures, asymmetric in plan and
elevation are analyzed and also torsional effects are taking into the
account. These analyses are performed using both near fault and far
fault records. In order to verify the results, the Incremental Dynamic
Analysis (IDA) is performed.
Abstract: The modified Claus process is the major technology
for the recovery of elemental sulfur from hydrogen sulfide. The
chemical reactions that can occur in the reaction furnace are
numerous and many byproducts such as carbon disulfide and carbon
carbonyl sulfide are produced. These compounds can often contribute
from 20 to 50% of the pollutants and therefore, should be hydrolyzed
in the catalytic converter. The inlet temperature of the first catalytic
reactor should be maintained over than 250 °C, to hydrolyze COS
and CS2. In this paper, the various configurations for the first
converter reheating of sulfur recovery unit are investigated. As a
result, the performance of each method is presented for a typical
clause unit. The results show that the hot gas method seems to be
better than the other methods.
Abstract: This paper presents Simulation and experimental
study aimed at investigating the effectiveness of an adaptive artificial
neural network stabilizer on enhancing the damping torque of a
synchronous generator. For this purpose, a power system comprising
a synchronous generator feeding a large power system through a
short tie line is considered. The proposed adaptive neuro-control
system consists of two multi-layered feed forward neural networks,
which work as a plant model identifier and a controller. It generates
supplementary control signals to be utilized by conventional
controllers. The details of the interfacing circuits, sensors and
transducers, which have been designed and built for use in tests, are
presented. The synchronous generator is tested to investigate the
effect of tuning a Power System Stabilizer (PSS) on its dynamic
stability. The obtained simulation and experimental results verify the
basic theoretical concepts.
Abstract: Drinking water is one of the most valuable resources
available to mankind. The presence of pathogens in drinking water is
highly undesirable. Because of the Lateritic soil, the iron
concentrations were high in ground water. High concentration of iron
and other trace elements could restrict bacterial growth and modify
their metabolic pattern as well. The bacterial growth rate reduced in
the presence of iron in water. This paper presents the results of a
controlled laboratory study conducted to assess the inhibition of
micro-organism (pathogen) in well waters in the presence of
dissolved iron concentrations. Synthetic samples were studied in the
laboratory and the results compared with field samples. Predictive
model for microbial inhibition in the presence of iron is presented. It
was seen that the bore wells, open wells and the field results varied,
probably due to the nature of micro-organism utilizing the iron in
well waters.
Abstract: Uranium mining and processing in Brazil occur in a
northeastern area near to Caetité-BA. Several Non-Governmental
Organizations claim that uranium mining in this region is a pollutant
causing health risks to the local population,but those in charge of the
complex extraction and production of“yellow cake" for generating
fuel to the nuclear power plants reject these allegations. This study
aimed at identifying potential problems caused by mining to the
population of Caetité. In this, work,the concentrations of 238U, 232Th
and 40K radioisotopes in the teeth of the Caetité population were
determined by ICP-MS. Teeth are used as bioindicators of
incorporated radionuclides. Cumulative radiation doses in the
skeleton were also determined. The concentration values were below
0.008 ppm, and annual effective dose due to radioisotopes are below
to the reference values. Therefore, it is not possible to state that the
mining process in Caetité increases pollution or radiation exposure in
a meaningful way.
Abstract: Majority of pepper farmers in Malaysia are using the
open-sun method for drying the pepper berries. This method is time
consuming and exposed the berries to rain and contamination. A
maintenance-friendly and properly enclosed dryer is therefore
desired. A dryer design with a solar collector and a chimney was
studied and adapted to suit the needs of small-scale pepper farmers in
Malaysia. The dryer will provide an environment with an optimum
operating temperature meant for drying pepper berries. The dryer
model was evaluated by using commercially available computational
fluid dynamic (CFD) software in order to understand the heat and
mass transfer inside the dryer. Natural convection was the only mode
of heat transportation considered in this study as in accordance to the
idea of having a simple and maintenance-friendly design. To
accommodate the effect of low buoyancy found in natural convection
driers, a biomass burner was integrated into the solar dryer design.
Abstract: This paper utilizes a finite element analysis to study
the bearing capacity of ring footings on a two-layered soil. The upper
layer, that the footing is placed on it, is soft clay and the underneath
layer is a cohesionless sand. For modeling soils, Mohr–Coulomb
plastic yield criterion is employed. The effects of two factors, the
clay layer thickness and the ratio of internal radius of the ring footing
to external radius of the ring, have been analyzed. It is found that the
bearing capacity decreases as the value of ri / ro increases.
Although, as the clay layer thickness increases the bearing capacity
was alleviated gradually.
Abstract: The present work was conducted for Arsenic (III)
removal, which one of the most poisonous groundwater pollutants, by
synthetic nano size zerovalent iron (nZVI). Batch experiments were
performed to investigate the influence of As (III), nZVI
concentration, pH of solution and contact time on the efficiency of As
(III) removal. nZVI was synthesized by reduction of ferric chloride
by sodium borohydrid. SEM and XRD were used to determine
particle size and characterization of produced nanoparticles. Up to
99.9% removal efficiency for arsenic (III) was obtained by nZVI
dosage of 1 g/L at time equal to 10 min. and pH=7. It could be
concluded that the removal efficiency were enhanced with increasing
of ZVI dosage and reaction time, but decreased with increasing of
arsenic concentration and pH for nano sized ZVI. nZVI presented an
outstanding ability to remove As (III) due to not only a high surface
area and low particle size but also to high inherent activity.
Abstract: The concentrations of aliphatic and polycyclic aromatic hydrocarbons (PAH) were determined in atmospheric aerosol samples collected at a rural site in Hungary (K-puszta, summer 2008), a boreal forest (Hyytiälä,
April 2007) and a polluted rural area in Italy (San Pietro Capofiume, Po Valley, April 2008). A clear distinction between “clean" and “polluted" periods was observed. Concentrations obtained for Hyytiälä are significantly lower than those for the other two sites. Source reconciliation was performed using diagnostic parameters, such as the carbon preference index and ratios between PAH. The presence of an unresolved complex mixture of hydrocarbons, especially for the Finnish and Italian samples, is indicative of petrogenic inputs. In K-puszta, the aliphatic hydrocarbons are dominated by leaf wax n-alkanes. The long range transport of anthropogenic pollution contributed to the Finnish aerosol. Industrial activities and vehicular emissions represent major sources in San Pietro Capofiume. PAH in K-puszta consist of both pyrogenic and petrogenic compounds.
Abstract: In present communication, we have developed the
suitable constraints for the given the mean codeword length and the
measures of entropy. This development has proved that Renyi-s
entropy gives the minimum value of the log of the harmonic mean
and the log of power mean. We have also developed an important
relation between best 1:1 code and the uniquely decipherable code by
using different measures of entropy.
Abstract: Tread design has evolved over the years to achieve the common tread pattern used in current vehicles. However, to meet safety and comfort requirements, tread design considers more than one design factor. Tread design must consider the grip and drainage, and the manner in which to reduce rolling noise, which is one of the main factors considered by manufacturers. The main objective of this study was the application the computational fluid dynamics (CFD) technique to simulate the contact surface of the tire and ground. The results demonstrated an air-Pumping and large pressure drop effect in the process of contact surface. The results also revealed that the pressure can be used to analyze sound pressure level (SPL).
Abstract: With major technological advances and to reduce the
cost of training apprentices for real-time critical systems, it was
necessary the development of Intelligent Tutoring Systems for
training apprentices in these systems. These systems, in general, have
interactive features so that the learning is actually more efficient,
making the learner more familiar with the mechanism in question. In
the home stage of learning, tests are performed to obtain the student's
income, a measure on their use. The aim of this paper is to present a
framework to model an Intelligent Tutoring Systems using the UML
language. The various steps of the analysis are considered the
diagrams required to build a general model, whose purpose is to
present the different perspectives of its development.
Abstract: Chess is one of the indoor games, which improves the
level of human confidence, concentration, planning skills and
knowledge. The main objective of this paper is to help the chess
players to improve their chess openings using data mining
techniques. Budding Chess Players usually do practices by analyzing
various existing openings. When they analyze and correlate
thousands of openings it becomes tedious and complex for them. The
work done in this paper is to analyze the best lines of Blackmar-
Diemer Gambit(BDG) which opens with White D4... using data
mining analysis. It is carried out on the collection of winning games
by applying association rules. The first step of this analysis is
assigning variables to each different sequence moves. In the second
step, the sequence association rules were generated to calculate
support and confidence factor which help us to find the best
subsequence chess moves that may lead to winning position.
Abstract: Data from 1731 Gentile di Puglia lambs, sired by 65 rams over a 5-year period were analyzed by a mixed model to estimate the variance components for heritability. The considered growth traits were: birth weight (BW), weight at 30 days of age (W30) and average daily gain from birth to 30 days of age (DG). Year of birth, sex of lamb, type of birth (single or twin), dam age at lambing and farm were significant sources of variation for all the considered growth traits. The average lamb weights were 3.85±0.16 kg at birth, 9.57±0.91 kg at 30 days of age and the average daily gain was 191±14 g. Estimates of heritability were 0.33±0.05, 0.41±0.06 and 0.16±0.05 respectively for the same traits. These values suggest there is a good opportunity to improve Gentile di Puglia lambs by selecting animals for growth traits.
Abstract: We developed a non-contact method for the in-situ
monitoring of the thermal forming of glass and Si foils to optimize
the manufacture of mirrors for high-resolution space x-ray
telescopes. Their construction requires precise and light-weight
segmented optics with angular resolution better than 5 arcsec. We
used 75x25 mm Desag D263 glass foils 0.75 mm thick and 0.6 mm
thick Si foils. The glass foils were shaped by free slumping on a
frame at viscosities in the range of 109.3-1012 dPa·s, the Si foils by
forced slumping above 1000°C. Using a Nikon D80 digital camera,
we took snapshots of a foil-s shape every 5 min during its isothermal
heat treatment. The obtained results we can use for computer
simulations. By comparing the measured and simulated data, we can
more precisely define material properties of the foils and optimize
the forming technology.
Abstract: A number of routing algorithms based on learning
automata technique have been proposed for communication
networks. How ever, there has been little work on the effects of
variation of graph scarcity on the performance of these algorithms. In
this paper, a comprehensive study is launched to investigate the
performance of LASPA, the first learning automata based solution to
the dynamic shortest path routing, across different graph structures
with varying scarcities. The sensitivity of three main performance
parameters of the algorithm, being average number of processed
nodes, scanned edges and average time per update, to variation in
graph scarcity is reported. Simulation results indicate that the LASPA
algorithm can adapt well to the scarcity variation in graph structure
and gives much better outputs than the existing dynamic and fixed
algorithms in terms of performance criteria.
Abstract: In this work, study the location of interface in a stirred vessel with Rushton impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: Most electrical distribution systems are incurring large
losses as the loads are wide spread, inadequate reactive power
compensation facilities and their improper control. A typical static
VAR compensator consists of capacitor bank in binary sequential
steps operated in conjunction with a thyristor controlled reactor of the
smallest step size. This SVC facilitates stepless control of reactive
power closely matching with load requirements so as to maintain
power factor nearer to unity. This type of SVC-s requiring a
appropriately controlled TCR. This paper deals with an air cored
reactor suitable for distribution transformer of 3phase, 50Hz, Dy11,
11KV/433V, 125 KVA capacity. Air cored reactors are designed,
built, tested and operated in conjunction with capacitor bank in five
binary sequential steps. It is established how the delta connected TCR
minimizes the harmonic components and the operating range for
various electrical quantities as a function of firing angle is
investigated. In particular firing angle v/s line & phase currents, D.C.
components, THD-s, active and reactive powers, odd and even triplen
harmonics, dominant characteristic harmonics are all investigated and
range of firing angle is fixed for satisfactory operation. The harmonic
spectra for phase and line quantities at specified firing angles are
given. In case the TCR is operated within the bound specified in this
paper established through simulation studies are yielding the best
possible operating condition particularly free from all dominant
harmonics.