Abstract: Reliable information about tool temperature
distribution is of central importance in metal cutting. In this study,
tool-chip interface temperature was determined in cutting of ST37
steel workpiece by applying HSS as the cutting tool in dry turning.
Two different approaches were implemented for temperature
measuring: an embedded thermocouple (RTD) in to the cutting tool
and infrared (IR) camera. Comparisons are made between
experimental data and results of MSC.SuperForm and FLUENT
software.
An investigation of heat generation in cutting tool was performed
by varying cutting parameters at the stable cutting tool geometry and
results were saved in a computer; then the diagrams of tool
temperature vs. various cutting parameters were obtained. The
experimental results reveal that the main factors of the increasing
cutting temperature are cutting speed (V ), feed rate ( S ) and depth
of cut ( h ), respectively. It was also determined that simultaneously
change in cutting speed and feed rate has the maximum effect on
increasing cutting temperature.
Abstract: Nowadays use of a new structural bracing system
called 'Knee Bracing System' have taken the specialists attention too
much. On the other hand nonlinear static analysis procedures in
estimate structures performance in earthquake time have taken
attention too much. One of these procedure is modal pushover
analysis (MPA) procedure. The accuracy of MPA procedure for
simple steel moment resisting frame has been verified and considered
in Chintanapakdee and Chopra-s article in 2003. Since the accuracy
of MPA procedure has not verified for semi-rigid steel frames with
knee bracing, we are going to get through with this matter in this
study. For this purpose, the selected structures are four frames with
different heights, 5 to 20 stories, will be designed according to AISC
criteria. Then MPA procedure is used for the same frames with
different rigidity percentiles of connections. The results of seismic
responses are compared with dynamic nonlinear response history
analysis as exact procedure and accuracy of MPA procedure is
evaluated. It seems that MPA procedure accuracy will come down by
reduction of the rigidity percentiles of semi-rigid connections.
Abstract: Some physical properties of musk lime (Citrus
microcarpa) were determined in this study. The average moisture
content (wet basis) of the fruit was found to be 85.10 (±0.72) %. The
mean of length, width and thickness of the fruit was 26.36 (±0.97),
26.40 (±1.04) and 25.26 (±0.94) mm respectively. The average value
for geometric mean diameter, sphericity, aspect ratio, mass, surface
area, volume, true density, bulk density and porosity was 26.00
(±0.82) mm, 98.67 (±2.04) %, 100.23 (±3.28) %, 10.007 (±0.878) g,
2125.07 (±133.93) mm2, 8800.00 (±731.82) mm3, 1002.87 (±39.16)
kgm-3, 501.70 (±22.58) kgm-3 and 49.89 (±3.15) % respectively.
The coefficient of static friction on four types of structural surface
was found to be varying from 0.238 (±0.025) for glass to 0.247
(±0.024) for steel surface.
Abstract: This paper investigates the performance of a speech
recognizer in an interactive voice response system for various coded
speech signals, coded by using a vector quantization technique namely
Multi Switched Split Vector Quantization Technique. The process of
recognizing the coded output can be used in Voice banking application.
The recognition technique used for the recognition of the coded speech
signals is the Hidden Markov Model technique. The spectral distortion
performance, computational complexity, and memory requirements of
Multi Switched Split Vector Quantization Technique and the
performance of the speech recognizer at various bit rates have been
computed. From results it is found that the speech recognizer is
showing better performance at 24 bits/frame and it is found that the
percentage of recognition is being varied from 100% to 93.33% for
various bit rates.
Abstract: Data mining (DM) is the process of finding and extracting frequent patterns that can describe the data, or predict unknown or future values. These goals are achieved by using various learning algorithms. Each algorithm may produce a mining result completely different from the others. Some algorithms may find millions of patterns. It is thus the difficult job for data analysts to select appropriate models and interpret the discovered knowledge. In this paper, we describe a framework of an intelligent and complete data mining system called SUT-Miner. Our system is comprised of a full complement of major DM algorithms, pre-DM and post-DM functionalities. It is the post-DM packages that ease the DM deployment for business intelligence applications.
Abstract: Biomass is becoming a large renewable resource for
power generation; it is involved in higher frequency in
environmentally clean processes, and even it is used for biofuels
preparation. On the other hand, hydrogen – other energy source – can
be produced in a variety of methods including gasification of
biomass. In this study, the production of hydrogen by gasification of
biomass waste is examined. This work explores the production of a
gaseous mixture with high power potential from Amazonas´ specie
known as copoazu, using a counter-flow fixed-bed bioreactor.
Abstract: There are four challenges of sustainable development
and in corporate level sustainability management-s role is to answer
for ecological sustainability challenge, social sustainability challenge,
economic sustainability challenges to environment and social
management and integration challenge of corporate sustainable
challenges by the help of different concepts, methods, instruments,
which are in the toolbox of sustainability management. These
instruments, concepts have different relevance in these challenges,
and according to different literatures environmental management is
outside of social and integration challenge. Main aim of this paper is
to represent the answer for the question that: is it true that social and
integration point of view is outside of the concept environmental
accounting? Using literature review and primer research at the end of
the paper the answer will be confirmed.
Abstract: The development of renewable energies - particularly energy from wind, water, solar power and biomass - is a central aim of the European Commission's energy policy. There are several reasons for this choice: renewable energies are sustainable, nonpolluting, widely available and clean. Increasing the share of renewable energy in the energy balance enhances sustainability. It also helps to improve the security of energy supply by reducing the Community's growing dependence on imported energy sources.In this paper it was studied the possibility to realize three photovoltaic systems in the Italian Natural Park “Gola della Rossa e di Frasassi". The first photovoltaic system is a grid-connected system for Services and Documentation Center of Castelletta with a nominal power of about 6 kWp. The second photovoltaic system is a grid-connected integrated system on the ticket office-s roof with a nominal power of about 4 kWp. The third project is set up by five grid-connected systems integrated on the roofs of the bungalows in Natural Park-s tourist camping with a nominal power of about 10 kWp. The electricity which is generated by all these plants is purchased according to the Italian program called “Conto Energia". Economical analysis and the amount of the avoided CO2 emissions are elaborated for these photovoltaic systems.
Abstract: This research is part of a broad program aimed at
advancing the science and technology involved in the rescue and
rehabilitation of oiled wildlife. One aspect of this research involves
the use of oil-sequestering magnetic particles for the removal of
contaminants from plumage – so-called “magnetic cleansing". This
treatment offers a number of advantages over conventional
detergent-based methods including portability - which offers the
possibility of providing a “quick clean" to the animal upon first
encounter in the field. This could be particularly advantageous
when the contaminant is toxic and/or corrosive and/or where there
is a delay in transporting the victim to a treatment centre. The
method could also be useful as part of a stabilization protocol when
large numbers of affected animals are awaiting treatment. This
presentation describes the design, development and testing of a
prototype field kit for providing a “quick clean" to contaminated
wildlife in the field.
Abstract: Dense slurry flow through centrifugal pump casing
has been modeled using the Eulerian-Eulerian approach with
Eulerian multiphase model in FLUENT 6.1®. First order upwinding
is considered for the discretization of momentum, k and ε terms.
SIMPLE algorithm has been applied for dealing with pressurevelocity
coupling. A mixture property based k-ε turbulence model
has been used for modeling turbulence. Results are validated first
against mesh independence and experiments for a particular set of
operational and geometric conditions. Parametric analysis is then
performed to determine the effect on important physical quantities
viz. solid velocities, solid concentration and solid stresses near the
wall with various operational geometric conditions of the pump.
Abstract: State-based testing is frequently used in software testing. Test data generation is one of the key issues in software testing. A properly generated test suite may not only locate the errors in a software system, but also help in reducing the high cost associated with software testing. It is often desired that test data in the form of test sequences within a test suite can be automatically generated to achieve required test coverage. This paper proposes an Ant Colony Optimization approach to test data generation for the state-based software testing.
Abstract: Graphene-metal contact resistance limits the performance of graphene-based electrical devices. In this work, we have fabricated both graphene field-effect transistors (GFET) and transfer length measurement (TLM) test devices with titanium contacts. The purpose of this work is to compare the contact resistances that can be numerically extracted from the GFETs and measured from the TLM structures. We also provide a brief review of the work done in the field to solve the contact resistance problem.
Abstract: This research aims to study employment trends in
printing industry for prepress support by Suan Sunandha University
Fund. The objectives of this research are to explain the trends of the
employment in Thai Printing Industry for prepress in Bangkok and
the description of different personnel that prepress entrepreneur need
and also the problems of employment.
The population of prepress entrepreneurs is about 100
organizations in the area of Bangkok. The questionnaires has been
taken and analyzed with SPSS program by using the average
percentage and standard deviation.
This research is multiple case studies. The conceptual framework
is developed on the basis of the open systems theory.
The research result show that
1. The most of prepress entrepreneur have trend to choose the
employee by any sex, the age 25-29 years old, bachelor degree
and have 1-2 years experience.
2. The most problems are the understanding in job,
communication/relation and the understanding in new
technology.
3. The trends aims to employment in 1-3 years have 57.8% for
prepress industry in Bangkok.
This research suggests that:
1. Thai printing industry for prepress in Bangkok need quality
employee that expert in printing technology.
2. Prepress entrepreneur should have agreement to development
with university for practice the employee.
3. Prepress entrepreneur should support personal to fulfill the
knowledge.
Abstract: The European countries that during the past two
decades based their exchange rate regimes on currency board
arrangement (CBA) are usually analysed from the perspective of
corner solution choice’s stabilisation effects. There is an open
discussion on the positive and negative background of a strict
exchange rate regime choice, although it should be seen as part of the
transition process towards the monetary union membership. The
focus of the paper is on the Baltic countries that after two decades of
a rigid exchange rate arrangement and strongly influenced by global
crisis are finishing their path towards the euro zone. Besides the
stabilising capacity, the CBA is highly vulnerable regime, with
limited developing potential. The rigidity of the exchange rate (and
monetary) system, despite the ensured credibility, do not leave
enough (or any) space for the adjustment and/or active crisis
management. Still, the Baltics are in a process of recovery, with fiscal
consolidation measures combined with (painful and politically
unpopular) measures of internal devaluation. Today, two of them
(Estonia and Latvia) are members of euro zone, fulfilling their
ultimate transition targets, but de facto exchanging one fixed regime
with another.
The paper analyses the challenges for the CBA in unstable
environment since the fixed regimes rely on imported stability and
are sensitive to external shocks. With limited monetary instruments,
these countries were oriented to the fiscal policies and used a
combination of internal devaluation and tax policy measures. Despite
their rather quick recovery, our second goal is to analyse the long
term influence that the measures had on the national economy.
Abstract: For high-speed control of robots, a good knowledge of system modelling is necessary to obtain the desired bandwidth. In this paper, we present a cartesian robot with a pan/tilt unit in end-effector (5 dof). This robot is implemented with powerful direct drive AC induction machines. The dynamic model, parameter identification and model validation of the robot are studied (including actuators). This work considers the cartesian robot coupled and non linear (contrary to normal considerations for this type of robots). The mechanical and control architecture proposed in this paper is efficient for industrial and research application in which high speed, well known model and very high accuracy are required.
Abstract: Wheeled Mobile Robots (WMRs) are built with their
Wheels- drive machine, Motors. Depend on their desire design of
WMR, Technicians made used of DC Motors for motion control. In
this paper, the author would like to analyze how to choose DC motor
to be balance with their applications of especially for WMR.
Specification of DC Motor that can be used with desire WMR is to
be determined by using MATLAB Simulink model. Therefore, this
paper is mainly focus on software application of MATLAB and
Control Technology. As the driving system of DC motor, a
Peripheral Interface Controller (PIC) based control system is
designed including the assembly software technology and H-bridge
control circuit. This Driving system is used to drive two DC gear
motors which are used to control the motion of WMR. In this
analyzing process, the author mainly focus the drive system on
driving two DC gear motors that will control with Differential Drive
technique to the Wheeled Mobile Robot . For the design analysis of
Motor Driving System, PIC16F84A is used and five inputs of sensors
detected data are tested with five ON/OFF switches. The outputs of
PIC are the commands to drive two DC gear motors, inputs of Hbridge
circuit .In this paper, Control techniques of PIC
microcontroller and H-bridge circuit, Mechanism assignments of
WMR are combined and analyzed by mainly focusing with the
“Modeling and Simulink of DC Motor using MATLAB".
Abstract: This paper describes studies carried out to investigate
the viability of using wireless cameras as a tool in monitoring
changes in air quality. A camera is used to monitor the change in
colour of a chemically responsive polymer within view of the camera
as it is exposed to varying chemical species concentration levels. The
camera captures this image and the colour change is analyzed by
averaging the RGB values present. This novel chemical sensing
approach is compared with an established chemical sensing method
using the same chemically responsive polymer coated onto LEDs. In
this way, the concentration levels of acetic acid in the air can be
tracked using both approaches. These approaches to chemical plume
tracking have many applications for air quality monitoring.
Abstract: A reduced-bit multiplication algorithm based on the ancient Vedic multiplication formulae is proposed in this paper. Both the Vedic multiplication formulae, Urdhva tiryakbhyam and Nikhilam, are first discussed in detail. Urdhva tiryakbhyam, being a general multiplication formula, is equally applicable to all cases of multiplication. It is applied to the digital arithmetic and is shown to yield a multiplier architecture which is very similar to the popular array multiplier. Due to its structure, it leads to a high carry propagation delay in case of multiplication of large numbers. Nikhilam Sutra, on the other hand, is more efficient in the multiplication of large numbers as it reduces the multiplication of two large numbers to that of two smaller numbers. The framework of the proposed algorithm is taken from this Sutra and is further optimized by use of some general arithmetic operations such as expansion and bit-shifting to take advantage of bit-reduction in multiplication. We illustrate the proposed algorithm by reducing a general 4x4-bit multiplication to a single 2 x 2-bit multiplication operation.
Abstract: A research effort to find the reality of the business of Japan-s software globalization of enterprise-level business software systems has found that while the number of Japan-made enterpriselevel software systems is comparable with those of the other G7 countries, the business is limited to the East and Southeast Asian markets. This indicates that this business has a problem in the European and USA markets. Based on the knowledge that the research has established, the research concludes that the communication problems arise from the lack of individualists' communication styles and foreign language skills in Japan's software globalization is compensated by similarities in certain Japanese cultural factors and Japan's cultural power in the East and Southeast Asian markets and that this business does not have this compensation factor in the European and American markets due to dissimilarities and no cultural power.
Abstract: There is increasing pressure on, and decline of
mopane woodlands due to increasing use and competition for
mopane resources in Zimbabwe in Namibia. Community management strategies, based largely on local knowledge are
evidently unable to cope. Research has generated potentially useful
information for mopane woodland management, but this information
has not been utilized. The work reported in this paper sought to add value to research work conducted on mopane woodlands by
developing effective community-based mopane woodland
management regimes that were based on both local and scientific
knowledge in Zimbabwe and Namibia. The conditions under which research findings were likely to be adopted for mopane woodland management by communities were investigated. The study was conducted at two sites each in Matobo and Omusati Districts in Zimbabwe and Namibia respectively. The mopane woodland
resources in the two study areas were assessed using scientific
ecological methods. A range of participatory methods was used to collect information on use of mopane woodland resources by communities, institutional arrangements governing access to and use
of these resources and to evaluate scientific knowledge for
applicability in local management regimes. Coppicing, thinning and
pollarding were the research generated management methods evaluated. Realities such as availability of woodland resources and
social roles and responsibilities influenced preferences for woodland
management interventions