Abstract: By enhancing the applicatıon of grounds for
establishment and due to the lack of appropriate sites, engineers
attempt to seek out a new method to reduce the weakness of soils. İn
aspect of economic situation, various ways have been used to
decrease the weak grounds. Because of the rapid development of
infrastructural facilities, spreading the construction operation is an
obligation. Furthermore, in various sites with the really bad soil
situation, engineers have considered obvious problems. One of the
most essential ways for developing the weak soils is stone column.
Obviously, the method was introduced in France in 1830 to improve
a native soil initially. Stone columns have an expanding range of
usage in different rough foundation sites all over the world to
increase the bearing capacity, to reduce the whole and differential
settlements, to enhance the rate of consolidation, to stabilize slopes
stability of embankments and to increase the liquefaction resistance
as well. A recent procedure called installing vertical nails along the
round stone columns in order to make better the performance of
considered columns is offered. Moreover, thanks to the enhancing the
nail diameter, number and embedment nail depth, the positive points
of vertical circumferential nails increases. Based on the result of this
study, load caring capacity will be develop with enhancing the length
and the power of reinforcements in vertical encasement stone column
(CESC). In this study, the main purpose is comparing two methods of
stone columns (installed a nail surrounding the stone columns and
using geogrid on clay) for enhancing the bearing capacity, decreasing
the whole and various settlements.
Abstract: This paper presents a fully Lagrangian coupled
Fluid-Structure Interaction (FSI) solver for simulations of
fluid-structure interactions, which is based on the Moving Particle
Semi-implicit (MPS) method to solve the governing equations
corresponding to incompressible flows as well as elastic structures.
The developed solver is verified by reproducing the high velocity
impact loads of deformable thin wedges with three different materials
such as mild steel, aluminium and tin during water entry. The present
simulation results for aluminium are compared with analytical solution
derived from the hydrodynamic Wagner model and linear Wan’s
theory. And also, the impact pressure and strain on the water entry
wedge with three different materials, such as mild steel, aluminium
and tin, are simulated and the effects of hydro-elasticity are discussed.
Abstract: Batch production plants provide a wide range of
scheduling problems. In pharmaceutical industries a batch process
is usually described by a recipe, consisting of an ordering of tasks
to produce the desired product. In this research work we focused
on pharmaceutical production processes requiring the culture of
a microorganism population (i.e. bacteria, yeasts or antibiotics).
Several sources of uncertainty may influence the yield of the culture
processes, including (i) low performance and quality of the cultured
microorganism population or (ii) microbial contamination. For
these reasons, robustness is a valuable property for the considered
application context. In particular, a robust schedule will not collapse
immediately when a cell of microorganisms has to be thrown away
due to a microbial contamination. Indeed, a robust schedule should
change locally in small proportions and the overall performance
measure (i.e. makespan, lateness) should change a little if at all.
In this research work we formulated a constraint programming
optimization (COP) model for the robust planning of antibiotics
production. We developed a discrete-time model with a multi-criteria
objective, ordering the different criteria and performing a
lexicographic optimization. A feasible solution of the proposed
COP model is a schedule of a given set of tasks onto available
resources. The schedule has to satisfy tasks precedence constraints,
resource capacity constraints and time constraints. In particular
time constraints model tasks duedates and resource availability
time windows constraints. To improve the schedule robustness, we
modeled the concept of (a, b) super-solutions, where (a, b) are input
parameters of the COP model. An (a, b) super-solution is one in
which if a variables (i.e. the completion times of a culture tasks)
lose their values (i.e. cultures are contaminated), the solution can be
repaired by assigning these variables values with a new values (i.e.
the completion times of a backup culture tasks) and at most b other
variables (i.e. delaying the completion of at most b other tasks).
The efficiency and applicability of the proposed model is
demonstrated by solving instances taken from a real-life
pharmaceutical company. Computational results showed that
the determined super-solutions are near-optimal.
Abstract: An investigation has been presented to analyze the
effect of internal heat source on the onset of Hadley-Prats flow in
a horizontal fluid saturated porous medium. We examine a better
understanding of the combined influence of the heat source and mass
flow effect by using linear stability analysis. The resultant eigenvalue
problem is solved by using shooting and Runga-Kutta methods for
evaluate critical thermal Rayleigh number with respect to various
flow governing parameters. It is identified that the flow is switch from
stabilizing to destabilizing as the horizontal thermal Rayleigh number
is enhanced. The heat source and mass flow increases resulting a
stronger destabilizing effect.
Abstract: The aim of this work was to characterize a potential
target group of people interested in participating into a training
program in organic farming in the context of mobile-learning. The
information sought addressed in particular, but not exclusively,
possible contents, formats and forms of evaluation that will
contribute to define the course objectives and curriculum, as well as
to ensure that the course meets the needs of the learners and their
preferences. The sample was selected among different European
countries. The questionnaires were delivered electronically for
answering on-line and in the end 135 consented valid questionnaires
were obtained. The results allowed characterizing the target group
and identifying their training needs and preferences towards m-learning
formats, giving valuable tools to design the training offer.
Abstract: Sewer deposits have been identified as a major cause
of dysfunctions in combined sewer systems regarding sewer
management, which induces different negative consequents resulting
in poor hydraulic conveyance, environmental damages as well as
worker’s health. In order to overcome the problematics of
sedimentation, flushing has been considered as the most operative
and cost-effective way to minimize the sediments impacts and
prevent such challenges. Flushing, by prompting turbulent wave
effects, can modify the bed form depending on the hydraulic
properties and geometrical characteristics of the conduit. So far, the
dynamics of the bed-load during high-flow events in combined sewer
systems as a complex environment is not well understood, mostly due
to lack of measuring devices capable to work in the “hostile” in
combined sewer system correctly. In this regards, a one-episode
flushing issue from an opening gate valve with weir function was
carried out in a trunk sewer in Paris to understand its cleansing
efficiency on the sediments (thickness: 0-30 cm). During more than
1h of flushing within 5 m distance in downstream of this flushing
device, a maximum flowrate and a maximum level of water have
been recorded at 5 m in downstream of the gate as 4.1 m3/s and 2.1
m respectively. This paper is aimed to evaluate the efficiency of this
type of gate for around 1.1 km (from the point -50 m to +1050 m in
downstream from the gate) by (i) determining bed grain-size
distribution and sediments evolution through the sewer channel, as
well as their organic matter content, and (ii) identifying sections that
exhibit more changes in their texture after the flush. For the first one,
two series of sampling were taken from the sewer length and then
analyzed in laboratory, one before flushing and second after, at same
points among the sewer channel. Hence, a non-intrusive sampling
instrument has undertaken to extract the sediments smaller than the
fine gravels. The comparison between sediments texture after the
flush operation and the initial state, revealed the most modified zones
by the flush effect, regarding the sewer invert slope and hydraulic
parameters in the zone up to 400 m from the gate. At this distance,
despite the increase of sediment grain-size rages, D50 (median grainsize)
varies between 0.6 mm and 1.1 mm compared to 0.8 mm and 10
mm before and after flushing, respectively. Overall, regarding the
sewer channel invert slope, results indicate that grains smaller than
sands (< 2 mm) are more transported to downstream along about 400
m from the gate: in average 69% before against 38% after the flush
with more dispersion of grain-sizes distributions. Furthermore, high
effect of the channel bed irregularities on the bed material evolution
has been observed after the flush.
Abstract: A large amount of software products offer a wide
range and number of features. This is called featuritis or creeping
featurism and tends to rise with each release of the product. Feautiris
often adds unnecessary complexity to software, leading to longer
learning curves and overall confusing the users and degrading their
experience. We take a look to a new design approach tendency that
has been coming up, the so-called “What You Get is What You
Need” concept that argues that products should be very focused,
simple and with minimalistic interfaces in order to help users conduct
their tasks in distraction-free ambiences. This isn’t as simple to
implement as it might sound and the developers need to cut down
features. Our contribution illustrates and evaluates this design method
through a novel distraction-free diagramming tool named Delineato
Pro for Mac OS X in which the user is confronted with an empty
canvas when launching the software and where tools only show up
when really needed.
Abstract: This research paper presents guiding on how to design
social media into higher education courses. The research
methodology used a survey approach. The research instrument was a
questionnaire about guiding on how to design social media into
higher education courses. Thirty-one lecturers completed the
questionnaire. The data were scored by frequency and percentage.
The research results were the lecturers’ opinions concerning the
designing social media into higher education courses as follows: 1)
Lecturers deem that the most suitable learning theory is Collaborative
Learning. 2) Lecturers consider that the most important learning and
innovation Skill in the 21st century is communication and
collaboration skills. 3) Lecturers think that the most suitable
evaluation technique is authentic assessment. 4) Lecturers consider
that the most appropriate portion used as blended learning should be
70% in the classroom setting and 30% online.
Abstract: In this paper, we report the development of the device
for diagnostics of cardiovascular system state and associated
automated workstation for large-scale medical measurement data
collection and analysis. It was shown that optimal design for the
monitoring device is wristband as it represents engineering trade-off
between accuracy and usability. Monitoring device is based on the
infrared reflective photoplethysmographic sensor, which allows
collecting multiple physiological parameters, such as heart rate and
pulsing wave characteristics. Developed device uses BLE interface
for medical and supplementary data transmission to the coupled
mobile phone, which processes it and send it to the doctor's
automated workstation. Results of this experimental model
approbation confirmed the applicability of the proposed approach.
Abstract: Standard Gibbs energy of formation ΔGfor(298.15) of
lanthanide-iron double oxides of garnet-type crystal structure
R3Fe5O12 - RIG (R – are rare earth ions) from initial oxides are
evaluated. The calculation is based on the data of standard entropies
S298.15 and standard enthalpies ΔH298.15 of formation of compounds
which are involved in the process of garnets synthesis. Gibbs energy
of formation is presented as temperature function ΔGfor(T) for the
range 300-1600K. The necessary starting thermodynamic data were
obtained from calorimetric study of heat capacity – temperature
functions and by using the semi-empirical method for calculation of
ΔH298.15 of formation. Thermodynamic functions for standard
temperature – enthalpy, entropy and Gibbs energy - are
recommended as reference data for technological evaluations.
Through the structural series of rare earth-iron garnets the correlation
between thermodynamic properties and characteristics of lanthanide
ions are elucidated.
Abstract: There is currently a gap in the technology covering the
rapid establishment of control after a reconfiguration in a
Reconfigurable Manufacturing System. This gap involves the
detection of the factory floor state and the communication link
between the factory floor and the high-level software. In this paper, a
thin, hardware-supported Middleware Management System (MMS) is
proposed and its design and implementation are discussed. The
research found that a cost-effective localization technique can be
combined with intelligent software to speed up the ramp-up of a
reconfigured system. The MMS makes the process more intelligent,
more efficient and less time-consuming, thus supporting the
industrial implementation of the RMS paradigm.
Abstract: In this article, we deal with a variant of the classical
course timetabling problem that has a practical application in many
areas of education. In particular, in this paper we are interested in
high schools remedial courses. The purpose of such courses is to
provide under-prepared students with the skills necessary to succeed
in their studies. In particular, a student might be under prepared in
an entire course, or only in a part of it. The limited availability
of funds, as well as the limited amount of time and teachers at
disposal, often requires schools to choose which courses and/or which
teaching units to activate. Thus, schools need to model the training
offer and the related timetabling, with the goal of ensuring the
highest possible teaching quality, by meeting the above-mentioned
financial, time and resources constraints. Moreover, there are some
prerequisites between the teaching units that must be satisfied. We
first present a Mixed-Integer Programming (MIP) model to solve
this problem to optimality. However, the presence of many peculiar
constraints contributes inevitably in increasing the complexity of
the mathematical model. Thus, solving it through a general-purpose
solver may be performed for small instances only, while solving
real-life-sized instances of such model requires specific techniques
or heuristic approaches. For this purpose, we also propose a heuristic
approach, in which we make use of a fast constructive procedure
to obtain a feasible solution. To assess our exact and heuristic
approaches we perform extensive computational results on both
real-life instances (obtained from a high school in Lecce, Italy) and
randomly generated instances. Our tests show that the MIP model is
never solved to optimality, with an average optimality gap of 57%.
On the other hand, the heuristic algorithm is much faster (in about the
50% of the considered instances it converges in approximately half of
the time limit) and in many cases allows achieving an improvement
on the objective function value obtained by the MIP model. Such an
improvement ranges between 18% and 66%.
Abstract: Low Temperature Matrix Isolation - Electron
Paramagnetic Resonance (LTMI-EPR) Spectroscopy was utilized to
identify the species of iron oxide nanoparticles generated during the
oxidative pyrolysis of 1-methylnaphthalene (1-MN). The otherwise
gas-phase reactions of 1--MN were impacted by a polypropylenimine
tetra-hexacontaamine dendrimer complexed with iron (III) nitrate
nonahydrate diluted in air under atmospheric conditions. The EPR
fine structure of Fe (III)2O3 nanoparticles clusters, characterized by gfactors
of 2.00, 2.28, 3.76 and 4.37 were detected on a cold finger
maintained at 77 K after accumulation over a multitude of
experiments. Additionally, a high valence Fe (IV) paramagnetic
intermediate and superoxide anion-radicals, O2•- adsorbed on
nanoparticle surfaces in the form of Fe (IV) --- O2•- were detected
from the quenching area of Zone 1 in the gas-phase.
Abstract: An approach was evaluated for the retrieval of soil
moisture of bare soil surface using bistatic scatterometer data in the
angular range of 200 to 700 at VV- and HH- polarization. The
microwave data was acquired by specially designed X-band (10
GHz) bistatic scatterometer. The linear regression analysis was done
between scattering coefficients and soil moisture content to select the
suitable incidence angle for retrieval of soil moisture content. The 250
incidence angle was found more suitable. The support vector
regression analysis was used to approximate the function described
by the input output relationship between the scattering coefficient and
corresponding measured values of the soil moisture content. The
performance of support vector regression algorithm was evaluated by
comparing the observed and the estimated soil moisture content by
statistical performance indices %Bias, root mean squared error
(RMSE) and Nash-Sutcliffe Efficiency (NSE). The values of %Bias,
root mean squared error (RMSE) and Nash-Sutcliffe Efficiency
(NSE) were found 2.9451, 1.0986 and 0.9214 respectively at HHpolarization.
At VV- polarization, the values of %Bias, root mean
squared error (RMSE) and Nash-Sutcliffe Efficiency (NSE) were
found 3.6186, 0.9373 and 0.9428 respectively.
Abstract: Determination of genetic variation is useful for plant
breeding and hence production of more efficient plant species under
different conditions, like drought stress. In this study a sample of 28
recombinant inbred lines (RILs) of wheat developed from the cross of
Norstar and Zagross varieties, together with their parents, were
evaluated for two years (2010-2012) under normal and water stress
conditions using split plot design with three replications. Main plots
included two irrigation treatments of 70 and 140 mm evaporation
from Class A pan and sub-plots consisted of 30 genotypes. The effect
of genotypes and interaction of genotypes with years and water
regimes were significant for all characters. Significant genotypic
effect implies the existence of genetic variation among the lines
under study. Heritability estimates were high for 1000 grain weight
(0.87). Biomass and grain yield showed the lowest heritability values
(0.42 and 0.50, respectively). Highest genotypic and phenotypic
coefficients of variation (GCV and PCV) belonged to harvest index.
Moderate genetic advance for most of the traits suggested the
feasibility of selection among the RILs under investigation. Some
RILs were higher yielding than either parent at both environments.
Abstract: New environmental regulations and the increasing
market preference for companies that respect the ecosystem had
encouraged the industry to look after new treatments for its effluents.
The sugar industry, one of the largest emitter of environmental
pollutants, follows this tendency. Membrane technology is
convenient for separation of suspended solids, colloids and high
molecular weight materials that are present in a wastewater from
sugar industry. The idea is to microfilter the wastewater, where the
permeate passes through the membrane and becomes available for
recycle and re-use in the sugar manufacturing process. For
microfiltration of this effluent a tubular ceramic membrane was used
with a pore size of 200 nm at transmembrane pressure in range of 1–3
bars and in range of flow rate of 50–150 l/h. Kenics static mixer was
used for permeate flux enhancement. Turbidity and suspended solids
were removed and the permeate flux was continuously monitored
during the microfiltration process. The flux achieved after 90 minutes
of microfiltration was in a range of 50–70 l/m2h. The obtained
turbidity decrease was in the range of 50-99 % and total amount of
suspended solids was removed.
Abstract: The possibility of application the dietary fibers in
production of crackers was observed in this work, as well as their
influence on rheological and textural properties on the dough for
crackers and influence on sensory properties of obtained crackers.
Three different dietary fibers, oat, potato and pea fibers, replaced
10% of wheat flour. Long fermentation process and baking test
method were used for crackers production. The changes of dough for
crackers were observed by rheological methods of determination the
viscoelastic dough properties and by textural measurements. Sensory
quality of obtained crackers was described using quantity descriptive
method (QDA) by trained members of descriptive panel. Additional
analysis of crackers surface was performed by videometer. Based on
rheological determination, viscoelastic properties of dough for
crackers were reduced by application of dietary fibers. Manipulation
of dough with 10% of potato fiber was disabled, thus the recipe
modification included increase in water content at 35%. Dough
compliance to constant stress for samples with dietary fibers
decreased, due to more rigid and stiffer dough consistency compared
to control sample. Also, hardness of dough for these samples
increased and dough extensibility decreased. Sensory properties of
final products, crackers, were reduced compared to control sample.
Application of dietary fibers affected mostly hardness, structure and
crispness of the crackers. Observed crackers were low marked for
flavor and taste, due to influence of fibers specific aroma. The sample
with 10% of potato fibers and increased water content was the most
adaptable to applied stresses and to production process. Also this
sample was close to control sample without dietary fibers by
evaluation of sensory properties and by results of videometer method.
Abstract: In insulation and cooling of power transformers
various liquids are used. Mineral oils have wide availability and low
cost. However, they have a poor biodegradability potential and lower
fire point in comparison with other insulating liquids. Use of a liquid
having high biodegradability is important due to environmental
consideration. This paper investigates edible corn oil as an alternative
to mineral oil. Various properties of mineral and corn oil like
breakdown voltage, dissipation factor, relative dielectric constant,
power loss and resistivity were measured according to different
standards.
Abstract: This report presents an alternative technique of
application of contrast agent in vivo, i.e. before sampling. By this
new method the electron micrograph of tissue sections have an
acceptable contrast compared to other methods and present no artifact
of precipitation on sections. Another advantage is that a small amount
of contrast is needed to get a good result given that most of them are
expensive and extremely toxic.
Abstract: A compact Ultra Wide Band (UWB) antenna with coplanar
waveguide feed has been designed and results are verified in
this paper. The antenna has been designed on FR4 substrate with
dielectric constant (εr) of 4.4 and dimensions of 32mm x 26mm x
0.8mm. The presented antenna shows return loss characteristics in the
band of 3.1 to 10.6 GHz as prescribed by FCC, USA. Parametric
studies have been done and results thus obtained have been
presented. Simulated results have been verified on Rohde & Swartz
VNA. The measured results are in good agreement with simulated
results which make the presented antenna suitable to be used for
wearable applications. Performance analysis of antenna has also been
shown in the presence of three layered Human Arm model. Results
obtained in presence of Human Arm model has been compared with
that in free space.