Abstract: Thermoacoustic refrigerator is a cooling device which
uses the acoustic waves to produce the cooling effect. The aim of this
paper is to explore the experimental and numerical feasibility of a
standing-wave thermoacoustic refrigerator. The effects of the stack
length, position of stack and operating frequency on the cooling
performance are carried out. The circular pore stacks are tested under
the atmospheric pressure. A low-cost loudspeaker is used as an
acoustic driver. The results show that the location of stack installed in
resonator tube has a greater effect on the cooling performance, than
the stack length and operating frequency, respectively. The
temperature difference across the ends of stack can be generated up
to 13.7°C, and the temperature of cold-end is dropped down by 5.3°C
from the ambient temperature.
Abstract: A seizure prediction method is proposed by extracting
global features using phase correlation between adjacent epochs for
detecting relative changes and local features using fluctuation/
deviation within an epoch for determining fine changes of different
EEG signals. A classifier and a regularization technique are applied
for the reduction of false alarms and improvement of the overall
prediction accuracy. The experiments show that the proposed method
outperforms the state-of-the-art methods and provides high prediction
accuracy (i.e., 97.70%) with low false alarm using EEG signals in
different brain locations from a benchmark data set.
Abstract: The transesterification of dimethyl malonate (DMM)
with phenol has been studied in vapour phase over cordierite
honeycomb coated with solid acid catalysts such as ZrO2,
Mo(VI)/ZrO2 and SO42-/ZrO2. The catalytic materials were prepared
honeycomb coated, powder forms, and characterized for their total
surface acidity by NH3-TPD and crystalinity by powder XRD
methods. Phenyl methyl malonate (PMM) and diphenyl malonate
(DPM) were obtained as the reaction products. A good conversion of
DMM (up to 82%) of MPM with 95% selectivity was observed when
the reactions were carried out at a catalyst bed temperature of 200 °C
and flow-rate of 10 mL/h in presence of Mo(VI)/ZrO2 as catalyst.
However, over SO4^2-/ZrO2 catalyst, the yield of DPM was found to be
higher. The results have been interpreted based on the variation of
acidic properties and powder XRD phases of zirconia on
incorporation of Mo(VI) or SO42– ions. Transesterification reactions
were also carried out over powder forms of the catalytic materials
and the yield of the desired phenyl ester products were compared
with that of the HC coated catalytic materials. The solid acids were
found to be reusable when used for at least 5 reaction cycles.
Abstract: Considering the challenges of short product life cycles
and growing variant diversity, cost minimization and manufacturing
flexibility increasingly gain importance to maintain a competitive
edge in today’s global and dynamic markets. In this context, an
aerodynamic part feeding system for high-speed industrial assembly
applications has been developed at the Institute of Production
Systems and Logistics (IFA), Leibniz Universitaet Hannover. The
aerodynamic part feeding system outperforms conventional systems
with respect to its process safety, reliability, and operating speed. In
this paper, a multi-objective optimisation of the aerodynamic feeding
system regarding the orientation rate, the feeding velocity, and the
required nozzle pressure is presented.
Abstract: A model to predict the plastic zone size for material
under plane stress condition has been developed and verified
experimentally. The developed model is a function of crack size,
crack angle and material property (dislocation density). Simulation
and validation results show that the model developed show good
agreement with experimental results. Samples of low carbon steel
(0.035%C) with included surface crack angles of 45o, 50o, 60o, 70o
and 90o and crack depths of 2mm and 4mm were subjected to low
strain rate between 0.48 x 10-3 s-1 – 2.38 x 10-3 s-1. The mechanical
properties studied were ductility, tensile strength, modulus of
elasticity, yield strength, yield strain, stress at fracture and fracture
toughness. The experimental study shows that strain rate has no
appreciable effect on the size of plastic zone while crack depth and
crack angle plays an imperative role in determining the size of the
plastic zone of mild steel materials.
Abstract: The goal of this paper is to identify the main
differences in the way men and women perceive TV ads. This paper
is based on a research project conducted partly as a review of relevant
papers, which deals with gender influence on the cognitive process
and postmodern perception of advertising. In addition to that,
qualitative research was conducted by means of interviews and
structured questionnaires. Furthermore, data acquired from the
research were used to evaluate our objectives and hypotheses. The
goal of this paper is to compare women's and men's perception of
advertisement. Although women are able to perceive more details
than men, men are more susceptible to sexual appeals in advertising.
Significant differences were also found in the perception of sexual
appeals in the context of gender.
Abstract: We have studied the temporal characteristics of
bistable perception of the stimuli of two types: one involves
alterations in a perceived depth and another one has an ambiguous
content. We used the Necker lattice and lines of shadowed circles
ambiguously perceived either as spheres or holes as stimuli of the
first type. The Winson figure (the Eskimo/Indian picture) was a
stimulus of the second type. We have analyzed how often the
reversals occurred (reversal rate) and for how long each of the two
interpretations, or percepts, was observed during one presentation
(stability durations). For all three ambiguous images the reversal rate
and the stability durations had similar values, which provide another
evidence for a significant role of top-down processes in multistable
perception.
Abstract: Production fluids are transported from the platform to
tankers or process facilities through transfer pipelines. Water being
one of the heavier phases tends to settle at the bottom of pipelines
especially at low flow velocities and this has adverse consequences
for pipeline integrity. On restart after a shutdown, this could result in
corrosion and issues for process equipment, thus the need to have the
heavier liquid dispersed into the flowing lighter fluid. This study
looked at the flow regime of low water cut and low flow velocity oil
and water flow using conductive film thickness probes in a large
diameter 4-inch pipe to obtain oil and water interface height and the
interface structural velocity. A wide range of 0.1–1.0 m/s oil and
water mixture velocities was investigated for 0.5–5% water cut. Two
fluid model predictions were used to compare with the experimental
results.
Abstract: Wind energy is rapidly emerging as the primary
source of electricity in the Philippines, although developing an
accurate wind resource model is difficult. In this study, Weather
Research and Forecasting (WRF) Model, an open source mesoscale
Numerical Weather Prediction (NWP) model, was used to produce a
1-year atmospheric simulation with 4 km resolution on the Ilocos
Region of the Philippines. The WRF output (netCDF) extracts the
annual mean wind speed data using a Python-based Graphical User
Interface. Lastly, wind resource assessment was produced using a
GIS software. Results of the study showed that it is more flexible to
use Python scripts than using other post-processing tools in dealing
with netCDF files. Using WRF Model, Python, and Geographic
Information Systems, a reliable wind resource map is produced.
Abstract: The underutilization of biomass resources in the
Philippines, combined with its growing population and the rise in
fossil fuel prices confirms demand for alternative energy sources. The
goal of this paper is to provide a comparison of MODIS-based and
Landsat-based agricultural land cover maps when used in the
estimation of rice hull’s available energy potential. Biomass resource
assessment was done using mathematical models and remote sensing
techniques employed in a GIS platform.
Abstract: This research aimed to investigate the relationship
between attitude towards marketing mix, brand image and consumer
behavior of the passengers of low-cost airlines service. This study
employed by quantitative research and the questionnaire was used to
collect the data from 400 sampled of the passengers who have ever
used the low-cost airline services based in Bangkok, Thailand. The
descriptive statistics and Pearson’s correlation analysis were used to
analyze data. The research results revealed that the attitude of the marketing mix
of the low-cost airline services including product, price, place,
promotion and process had related to the consumer behavior on the
aspects of duration of service and frequency of service. While, the
brand image of the low cost airline including the characteristics of
organization, service quality and company identity had related to the
consumer behavior on duration of service, frequency of service and
cost of service at the significant statistically acceptable levels.
Abstract: The aim of this study is to evaluate the effect of
supplementing broiler starter diet with different levels of an essential
oil blend (EOB) containing capsaicin, carvacrol and cinnamaldehyde
on the performance of broilers. A total of 300 day-old straight-run
Cobb broiler chicks were randomly assigned to three treatments after
7-day group brooding following a completely randomized design
(CRD). Birds assigned in treatment 1 were given starter basal diet
while those in treatments 2 and 3 were given starter basal diet with
400 mg/kg antibiotic growth promoter (AGP) and 150 mg/kg EOB,
respectively, until the 28th day. Basal finisher feed were given for all
the treatments until harvest. Following 37 d feeding, body weight
gain, feed consumption, feed efficiency, dressing percentage,
livability and jejunal villi height were determined. Results showed no
significant differences (P>0.05) in growth performance. However,
villi height and crypt depth was significantly lower for birds fed
EOB.
Abstract: Rotary entrainment is a phenomenon in which the
interface of two immiscible fluids are subjected to external flux by
means of rotation. Present work reports the experimental study on
rotary motion of a horizontal cylinder between the interface of air and
water to observe the penetration of gas inside the liquid. Experiments
have been performed to establish entrainment of air mass in water
alongside the cylindrical surface. The movement of tracer and seeded
particles has been tracked to calculate the speed and path of the
entrained air inside water. Simplified particle image velocimetry
technique has been used to trace the movement of particles/tracers at
the moment they are injected inside the entrainment zone and
suspended beads have been used to replicate the particle movement
with respect to time in order to determine the flow dynamics of the
fluid along the cylinder. Present paper establishes a thorough experimental analysis of the
rotary entrainment phenomenon between air and water keeping in
interest the extent to which we can intermix the two and also to study
its entrainment trajectories.
Abstract: This study investigates the influence of low
temperature thermo-chemical pretreatment of organic food waste on
performance of COD solubilisation. Both temperature and alkaline
agent were reported to have effect on solubilizing any possible
biomass including organic food waste. The three independent
variables considered in this pretreatment were temperature (50-90oC),
pretreatment time (30-120 minutes) and alkaline concentration,
sodium hydroxide, NaOH (0.7-15 g/L). The maximal condition
obtained were 90oC, 15 g/L NaOH for 2 hours. Solubilisation has
potential in enhancing methane production by providing high amount
of soluble components at early stage during anaerobic digestion.
Abstract: In this paper, we propose the variational EM inference
algorithm for the multi-class Gaussian process classification model
that can be used in the field of human behavior recognition. This
algorithm can drive simultaneously both a posterior distribution of a
latent function and estimators of hyper-parameters in a Gaussian
process classification model with multiclass. Our algorithm is based
on the Laplace approximation (LA) technique and variational EM
framework. This is performed in two steps: called expectation and
maximization steps. First, in the expectation step, using the Bayesian
formula and LA technique, we derive approximately the posterior
distribution of the latent function indicating the possibility that each
observation belongs to a certain class in the Gaussian process
classification model. Second, in the maximization step, using a derived
posterior distribution of latent function, we compute the maximum
likelihood estimator for hyper-parameters of a covariance matrix
necessary to define prior distribution for latent function. These two
steps iteratively repeat until a convergence condition satisfies.
Moreover, we apply the proposed algorithm with human action
classification problem using a public database, namely, the KTH
human action data set. Experimental results reveal that the proposed
algorithm shows good performance on this data set.
Abstract: The present research aimed at studying the awareness
and attitudes of teachers towards inclusive education. The sample
consisted of 60 teachers, teaching in the primary section (1st – 4th) of
regular schools affiliated to the SSC board in Mumbai. Sample was
selected by Multi-stage cluster sampling technique. A semi-structured
self-constructed interview schedule and a self-constructed attitude
scale was used to study the awareness of teachers about disability and
Inclusive education, and their attitudes towards inclusive education
respectively. Themes were extracted from the interview data and
quantitative data was analyzed using SPSS package. Results revealed
that teachers had some amount of awareness but an inadequate
amount of information on disabilities and inclusive education.
Disability to most (37) teachers meant “an inability to do something”.
The difference between disability and handicap was stated by most as
former being cognitive while handicap being physical in nature. With
regard to Inclusive education, a large number (46) stated that they
were unaware of the term and did not know what it meant. Majority
(52) of them perceived maximum challenges for themselves in an
inclusive set up, and emphasized on the role of teacher training
courses in the area of providing knowledge (49) and training in
teaching methodology (53). Although, 83.3% of teachers held a
moderately positive attitude towards inclusive education, a large
percentage (61.6%) of participants felt that being in inclusive set up
would be very challenging for both children with special needs and
without special needs. Though, most (49) of the teachers stated that
children with special needs should be educated in regular classroom
but they further clarified that only those should be in a regular
classroom who have physical impairments of mild or moderate
degree.
Abstract: Selling has changed. Selling has taken on aspects of
relationship marketing and sales force play a critical role in
developing long-term relationships between buyers and sellers which
is seen to serve the company’s targets and create success for a long
run. The purpose of this study was to examine what really matters in
buyer-seller encounters and determine what expectations business
buyers have. We studied 17 business buyers by a qualitative
interview. We found that buyers appreciate encounters where the
salesperson face the buyer as a way he or she is as a person, map the
real needs to improve buyers’ business and build up cooperation for
long-term relationship. This study show that personality matters are a
key elements when satisfying business buyers’ expectations.
Abstract: In the Solid-State-Drive (SSD) performance, whether
the data has been well parallelized is an important factor. SSD
parallelization is affected by allocation scheme and it is directly
connected to SSD performance. There are dynamic allocation and
static allocation in representative allocation schemes. Dynamic
allocation is more adaptive in exploiting write operation parallelism,
while static allocation is better in read operation parallelism.
Therefore, it is hard to select the appropriate allocation scheme when
the workload is mixed read and write operations. We simulated
conditions on a few mixed data patterns and analyzed the results to
help the right choice for better performance. As the results, if data
arrival interval is long enough prior operations to be finished and
continuous read intensive data environment static allocation is more
suitable. Dynamic allocation performs the best on write performance
and random data patterns.
Abstract: The 1:1 cocrystal of 2-amino-4-chloro-6-
methylpyrimidine (2A4C6MP) with 4-methylbenzoic acid (4MBA)
(I) has been prepared by slow evaporation method in methanol,
which was crystallized in monoclinic C2/c space group, Z = 8, and a
= 28.431 (2) Å, b = 7.3098 (5) Å, c = 14.2622 (10) Å and β =
109.618 (3)°. The presence of unionized –COOH functional group in
cocrystal I was identified both by spectral methods (1H and 13C
NMR, FTIR) and X-ray diffraction structural analysis. The
2A4C6MP molecule interact with the carboxylic group of the
respective 4MBA molecule through N—H⋯O and O—H⋯N
hydrogen bonds, forming a cyclic hydrogen–bonded motif R2
2(8).
The crystal structure was stabilized by Npyrimidine—H⋯O=C and
C=O—H⋯Npyrimidine types hydrogen bonding interactions.
Theoretical investigations have been computed by HF and density
function (B3LYP) method with 6–311+G (d,p)basis set. The
vibrational frequencies together with 1H and 13C NMR chemical
shifts have been calculated on the fully optimized geometry of
cocrystal I. Theoretical calculations are in good agreement with the
experimental results. Solvent–free formation of this cocrystal I is
confirmed by powder X-ray diffraction analysis.
Abstract: In this paper, we calculate the two-photon ionization
(TPI) cross-section for pump-probe scheme in Ag neutral cluster. The
pump photon energy is assumed to be close to the surface plasmon
(SP) energy of cluster in dielectric media. Due to this choice, the
pump wave excites collective oscillations of electrons-SP and the
probe wave causes ionization of the cluster. Since the interband
transition energy in Ag exceeds the SP resonance energy, the main
contribution into the TPI comes from the latter. The advantage of Ag
clusters as compared to the other noble metals is that the SP
resonance in silver cluster is much sharper because of peculiarities of
its dielectric function. The calculations are performed by separating
the coordinates of electrons corresponding to the collective
oscillations and the individual motion that allows taking into account
the resonance contribution of excited SP oscillations. It is shown that
the ionization cross section increases by two orders of magnitude if
the energy of the pump photon matches the surface plasmon energy
in the cluster.