Abstract: Wind turbine should be controlled to capture maximum
wind energy and to prevent the turbine from being stalled. To achieve
those two goals, wind turbine controller controls torque on generator
and limits input torque from wind by pitching blade. Usually, torque
on generator is controlled using inverter torque set point. However,
verifying a control algorithm in actual wind turbine needs a lot of
efforts to test and the actual wind turbine could be broken while testing
a control algorithm. So, several software have developed and
commercialized by Garrad Hassan, GH Bladed, and NREL, FAST.
Even though, those programs can simulate control system modeling
with subroutines or DLLs. However, those simulation programs are
not able to emulate detailed generator or PMSG. In this paper, a small
size wind turbine simulator is developed with induction motor and
small size drive train. The developed system can simulate wind turbine
control algorithm in the region before rated power.
Abstract: The Beshar River is one aquatic ecosystem,which is
affected by pollutants. This study was conducted to evaluate the
effects of human activities on the water quality of the Beshar river.
This river is approximately 190 km in length and situated at the
geographical positions of 51° 20' to 51° 48' E and 30° 18' to 30° 52'
N it is one of the most important aquatic ecosystems of Kohkiloye
and Boyerahmad province next to the city of Yasuj in southern Iran.
The Beshar river has been contaminated by industrial, agricultural
and other activities in this region such as factories, hospitals,
agricultural farms, urban surface runoff and effluent of wastewater
treatment plants. In order to evaluate the effects of these pollutants
on the quality of the Beshar river, five monitoring stations were
selected along its course. The first station is located upstream of
Yasuj near the Dehnow village; stations 2 to 4 are located east, south
and west of city; and the 5th station is located downstream of Yasuj.
Several water quality parameters were sampled. These include pH,
dissolved oxygen, biological oxygen demand (BOD), temperature,
conductivity, turbidity, total dissolved solids and discharge or flow
measurements. Water samples from the five stations were collected
and analysed to determine the following physicochemical
parameters: EC, pH, T.D.S, T.H, No2, DO, BOD5, COD during 2008
to 2009. The study shows that the BOD5 value of station 1 is at a
minimum (1.5 ppm) and increases downstream from stations 2 to 4 to
a maximum (7.2 ppm), and then decreases at station 5. The DO
values of station 1 is a maximum (9.55 ppm), decreases downstream
to stations 2 - 4 which are at a minimum (3.4 ppm), before increasing
at station 5. The amount of BOD and TDS are highest at the 4th
station and the amount of DO is lowest at this station, marking the
4th station as more highly polluted than the other stations. The
physicochemical parameters improve at the 5th station due to
pollutant degradation and dilution. Finally the point and nonpoint
pollutant sources of Beshar river were determined and compared to
the monitoring results.
Abstract: This paper proposes an analytical method for the
dynamics of generating firms- alliance networks along with business
phases. Dynamics in network developments have previously been
discussed in the research areas of organizational strategy rather than in
the areas of regional cluster, where the static properties of the
networks are often discussed. The analytical method introduces the
concept of business phases into innovation processes and uses
relationships called prior experiences; this idea was developed in
organizational strategy to investigate the state of networks from the
viewpoints of tradeoffs between link stabilization and node
exploration. This paper also discusses the results of the analytical
method using five cases of the network developments of firms. The
idea of Embeddedness helps interpret the backgrounds of the
analytical results. The analytical method is useful for policymakers of
regional clusters to establish concrete evaluation targets and a
viewpoint for comparisons of policy programs.
Abstract: Bandwidth allocation in wired network is less complex
and to allocate bandwidth in wireless networks is complex and
challenging, due to the mobility of source end system.This paper
proposes a new approach to bandwidth allocation to higher and lower
priority mobile nodes.In our proposal bandwidth allocation to new
mobile node is based on bandwidth utilization of existing mobile
nodes.The first section of the paper focuses on introduction to
bandwidth allocation in wireless networks and presents the existing
solutions available for allocation of bandwidth. The second section
proposes the new solution for the bandwidth allocation to higher and
lower priority nodes. Finally this paper ends with the analytical
evaluation of the proposed solution.
Abstract: The aim of this work was to study the in vitro effects
of δ-lactam 1 and its 4-chlorophenyl derivative 2, on the proliferative
responses of human lymphocytes and Th1 and Th2 cytokine
secretion. The possible protective role of vitamin E on intracellular
stress oxidative induced by these compounds was also investigated.
Peripheral blood lymphocytes were isolated using differential
centrifugation on a density gradient of Histopaque. They were
cultured with mitogen concanavalin A, vitamin E (10 μM) and with
different concentrations of the compounds 1 and 2 (0.1 to 10 μM).
Proliferation (MTT assay), IL-2, INFγ and IL-4 (Elisa kits),
intracellular superoxide anion were determined. 1 and 2 were
immunostimulant and increased cytokine secretion with a shift away
from Th1 response to Th2. These properties were however
accompanied by an increase in intracellular oxidative stress. The
presence of vitamin E exhibited protective effects by reducing δ-
lactam-induced superoxide anion generation in lymphocytes.
Abstract: This study developed a high efficient and combined
biological and chemical filter treatment process. This process used
PAC (Powder Activated Carbon), Alum and attached growth
treatment process. The system removals of total nitrogen and total
phosphorus ratio of two were as high as 70% and 73%, moreover, the
effluent water was suitable to urban and agricultural water. Also the
advantages of this process are not only occupies small place but is
simple, economic and easy operating. Besides, our developed process
can keep stable process efficiency even in relative low load level.
Therefore, this study judges that use of the high efficient and
combined biological and chemical filter treatment process, it is
expected that the effluent water in this system can be reused as urban
and agricultural water.
Abstract: This paper proposes a three-dimensional motion capture and feedback system of flying disc throwing action learners with use of Kinect device. Rather than conventional 3-D motion capture system, Kinect has advantages of cost merit, easy system development and operation. A novice learner of flying disc is trained to keep arm movement in steady height, to twist the waist, and to stretch the elbow according to the waist angle. The proposing system captures learners- body movement, checks their skeleton positions in pre-motion / motion / post-motion in several ways, and displays feedback messages to refine their actions.
Abstract: Optical Character Recognition (OCR) is a very old and of great interest in pattern recognition field. In this paper we introduce a very powerful approach to recognize Persian text. We have used morphological operators, especially Hit/Miss operator to descript each sub-word and by using a template matching approach we have tried to classify generated description. We used just one font in two different sizes to verify our approach. We achieved a very good rate, up to 99.9%.
Abstract: The general global behavior of particle S a non-linear (Q - xy)2 potential cannot be revealed a Poincare surface of section method (PSS) because inost trajectories take practically infinitely long time to integrate numerically before they come back to the surface. In this study as an alternative to PSS, a multiple scale perturbation is applied to analyze global adiabatic, non-adiabatic and chaotic behavior of particles in this potential. It was found that the results can be summarized as a form of a Fermi-like map. Additionally, this method gives a variation of global stochasticity criteria with Q.
Abstract: This paper presents the experimental results on effect of applied voltage stress frequency to the occurrence of electrical treeing in 22 kV cross linked polyethylene (XLPE) insulated cable.Hallow disk of XLPE insulating material with thickness 5 mm taken from unused high voltage cable was used as the specimen in this study. Stainless steel needle was inserted gradually into the specimen to give a tip to earth plane electrode separation of 2.50.2 mm at elevated temperature 105-110°C. The specimen was then annealed for 5 minute to minimize any mechanical stress build up around the needle-plane region before it was cooled down to room temperature. Each specimen were subjected to the same applied voltage stress level at 8 kV AC rms, with various frequency, 50, 100, 500, 1000 and 2000 Hz. Initiation time, propagation speed and pattern of electrical treeing were examined in order to study the effect of applied voltage stress frequency. By the experimental results, initial time of visible treeing decreases with increasing in applied voltage frequency. Also, obviously, propagation speed of electrical treeing increases with increasing in applied voltage frequency.Furthermore, two types of electrical treeing, bush-like and branch-like treeing were observed.The experimental results confirmed the effect of voltage stress frequency as well.
Abstract: Oral health is particular important to the hospitalized
patients with chronic schizophrenia for an extreme high potential of the respiratory infections. Due to the degeneration of physical capability, patients of this kind typically fall dependent in the activity of daily living (ADL). A very high percentage of patients had dental
problems of which mostly could be easily avoid by easy regular tooth brushing. Purpose of the project is to develop a mechanism in helping the schizophrenia patients in rebuilding a tooth-cleaning habit. The
project observed and evaluated the tooth-cleaning behavior of 100
male patients in a psychiatric hospital, and found the majority of them
ignored such an activity in a three-month period of time. In the meantime, the primary care-givers were not aware or not convinced
the importance of such a need of dental hygiene, and thus few if any
tooth cleaning training or knowledge on dental hygiene were given to
the patients. The project then developed a program based on the numerous observations and discussions. The improvement program
included patients- group education, care-givers- training, and a
tool-kit for tooth-brush holding was erected. The project launched
with some incentive package. The outcomes were encouraging with
87% of the patients had rebuilt their tooth-brushing habits against
previous 22%, and the tooth cleaning kits were 100% kept against 22%
in the past. This project had significantly improved the oral health of
the patients. The project, included the procedure and the tool-kit
holder specific for this purpose, was a good examples for psychiatric
hospitals.
Abstract: This paper presents features that characterize power
quality disturbances from recorded voltage waveforms using wavelet
transform. The discrete wavelet transform has been used to detect
and analyze power quality disturbances. The disturbances of interest
include sag, swell, outage and transient. A power system network has
been simulated by Electromagnetic Transients Program. Voltage
waveforms at strategic points have been obtained for analysis, which
includes different power quality disturbances. Then wavelet has been
chosen to perform feature extraction. The outputs of the feature
extraction are the wavelet coefficients representing the power quality
disturbance signal. Wavelet coefficients at different levels reveal the
time localizing information about the variation of the signal.
Abstract: We consider a two-way relay network where two sources exchange information. A relay helps the two sources exchange information using the decode-and-XOR-forward protocol. We investigate the power minimization problem with minimum rate constraints. The system needs two time slots and in each time slot the required rate pair should be achievable. The power consumption is minimized in each time slot and we obtained the closed form solution. The simulation results confirm that the proposed power allocation scheme consumes lower total power than the conventional schemes.
Abstract: This paper presented a MATLAB-based system named Smart Access Network Testing, Analyzing and Database (SANTAD), purposely for in-service transmission surveillance and self restoration against fiber fault in fiber-to-the-home (FTTH) access network. The developed program will be installed with optical line terminal (OLT) at central office (CO) to monitor the status and detect any fiber fault that occurs in FTTH downwardly from CO towards residential customer locations. SANTAD is interfaced with optical time domain reflectometer (OTDR) to accumulate every network testing result to be displayed on a single computer screen for further analysis. This program will identify and present the parameters of each optical fiber line such as the line's status either in working or nonworking condition, magnitude of decreasing at each point, failure location, and other details as shown in the OTDR's screen. The failure status will be delivered to field engineers for promptly actions, meanwhile the failure line will be diverted to protection line to ensure the traffic flow continuously. This approach has a bright prospect to improve the survivability and reliability as well as increase the efficiency and monitoring capabilities in FTTH.
Abstract: Educational institutions increasingly adopt the
students-as-customers concept to satisfy their students.
Understanding students- perspectives on the use of this business
concept in educational institutions is necessary for the institutions to
effectively align these perspectives with their management practice.
The study investigates whether students in technology and business
disciplines have significantly different attitudes toward using the
students-as-customers concept in educational institutions and
explores the impact of treating students as customers in technology
disciplines under students- perspectives. The results from
quantitative and qualitative data analyses show that technology
students, in contrast to business students, fairly disagree with
educational institutions to treat students as customers. Treating
students as customers in technology disciplines will have a negative
influence on teaching performance, instructor-student relationships
and educational institutions- aim, but a positive influence on service
quality in educational institutions. The paper discusses the findings
and concludes with implications and limitations of the study.
Abstract: A theoretical study of the rigidities of slabs with
circular voids oriented in the longitudinal and in the transverse
direction is discussed. Equations are presented for predicting the
bending and torsional rigidities of the voided slabs. This paper
summarizes the results of an extensive literature search and initial
review of the current methods of analyzing voided slab. The various
methods of calculating the equivalent plate parameters, which are
necessary for two-dimensional analysis, are also reviewed. Static
deflections on voided slabs are shown to be in good agreement with
proposed equation.
Abstract: This paper focuses on creating a component model of information system under uncertainty. The paper identifies problem in current approach of component modeling and proposes fuzzy tool, which will work with vague customer requirements and propose components of the resulting component model. The proposed tool is verified on specific information system and results are shown in paper. After finding suitable sub-components of the resulting component model, the component model is visualised by tool.
Abstract: The realization of current-mode quadrature oscillators
using current controlled current conveyor transconductance
amplifiers (CCCCTAs) and grounded capacitors is presented. The
proposed oscillators can provide 2 sinusoidal output currents with 90º
phase difference. It is enabled non-interactive dual-current control for
both the condition of oscillation and the frequency of oscillation.
High output impedances of the configurations enable the circuit to be
cascaded without additional current buffers. The use of only
grounded capacitors is ideal for integration. The circuit performances
are depicted through PSpice simulations, they show good agreement
to theoretical anticipation.
Abstract: This paper is the tomographic images reconstruction
simulation for defects detection in specimen. The specimen is the
thin cylindrical steel contained with low density materials. The
defects in material are simulated in three shapes.The specimen image
function will be transformed to projection data. Radon transform and
its inverse provide the mathematical for reconstructing tomographic
images from projection data. The result of the simulation show that
the reconstruction images is complete for defect detection.
Abstract: Lutein is a dietary oxycarotenoid which is found
to reduce the risks of Age-related Macular Degeneration
(AMD). Supercritical fluid extraction of lutein esters from
marigold petals was carried out and was found to be much
effective than conventional solvent extraction. The
saponification of pre-concentrated lutein esters to produce free
lutein was studied which showed a composition of about 88%
total carotenoids (UV-VIS spectrophotometry) and 90.7%
lutein (HPLC). The lipase catalyzed hydrolysis of lutein esters
in conventional medium was investigated. The optimal
temperature, pH, enzyme concentration and water activity
were found to be 50°C, 7, 15% and 0.33 respectively and the
activity loss of lipase was about 25% after 8 times re-use in at
50°C for 12 days. However, the lipase catalyzed hydrolysis of
lutein esters in conventional media resulted in poor
conversions (16.4%).