Abstract: Within Rapid Prototyping technologies are used many
types of materials. Many of them are recyclable but there are still as
plastic like, so practically they do not degrade in the landfill.
Polylactic acid (PLA) is one of the special plastic materials, which
are biodegradable and available for 3D printing within Fused
Deposition Modeling (FDM) technology. The question is, if the
mechanical properties of produced models are comparable to similar
technical plastic materials which are usual for prototype production.
Presented paper shows the experiments results for tensile strength
measurements for specimens prepared with different 3D printer
settings and model orientation. Paper contains also the comparison of
tensile strength values with values measured on specimens produced
by conventional technologies as injection moulding.
Abstract: The analytical bright two soliton solution of the 3-
coupled nonlinear Schrödinger equations with variable coefficients in
birefringent optical fiber is obtained by Darboux transformation
method. To the design of ultra-speed optical devices, Soliton
interaction and control in birefringence fiber is investigated. Lax pair
is constructed for N coupled NLS system through AKNS method.
Using two-soliton solution, we demonstrate different interaction
behaviors of solitons in birefringent fiber depending on the choice of
control parameters. Our results shows that interactions of optical
solitons have some specific applications such as construction of logic
gates, optical computing, soliton switching, and soliton amplification
in wavelength division multiplexing (WDM) system.
Abstract: Broiler slaughter waste has become a major source of
pollution throughout the world. Utilization of broiler slaughter waste
by dry rendering process produced Rendered Chicken Oil (RCO), a
cheap raw material for biodiesel production and Carcass Meal a feed
ingredient for pets and fishes. Conversion of RCO into biodiesel may
open new vistas for generating wealth from waste besides controlling
the major havoc of environmental pollution. A two-step process to
convert RCO to good quality Biodiesel was invented. Acid catalysed
esterification of FFA followed by base catalysed transesterification of
triglycerides was carried out after meticulously standardizing the
methanol molar ratio, catalyst concentration, reaction temperature,
and reaction time to obtain the maximum biodiesel yield of 97.62%
and lowest glycerol yield of 6.96%. RCO biodiesel blend was tested
in a CRDI diesel engine. The results revealed that the blending of
commercial diesel with 20% RCO biodiesel (B20) lead to less engine
wear, a quieter engine and better fuel economy. The better lubricating
qualities of RCO B20 prevented over heating of engine, which
prolongs the engine life. RCO B20 can reduce the import of crude oil
and substantially reduce the engine emissions as proved by
significantly lower smoke levels, thus mitigating climatic changes.
Abstract: The main cause of Alzheimer disease (AD) was
believed to be mainly due to the accumulation of free radicals owing
to oxidative stress (OS) in brain tissue. The mechanism of the
neurotoxicity of Aluminum chloride (AlCl3) induced AD in
hippocampus Albino wister rat brain tissue, the curative & the
protective effects of Lipidium sativum group (LS) water extract were
assessed after 8 weeks by attenuated total reflection spectroscopy
ATR-IR and histologically by light microscope. ATR-IR results
revealed that the membrane phospholipid undergo free radical
attacks, mediated by AlCl3, primary affects the polyunsaturated fatty
acids indicated by the increased of the olefinic -C=CH sub-band area
around 3012 cm-1 from the curve fitting analysis. The narrowing in
the half band width (HBW) of the sνCH2 sub-band around 2852 cm-1
due to Al intoxication indicates the presence of trans form fatty acids
rather than gauch rotomer. The degradation of hydrocarbon chain to
shorter chain length, increasing in membrane fluidity, disorder, and
decreasing in lipid polarity in AlCl3 group indicated by the detected
changes in certain calculated area ratios compared to the control.
Administration of LS was greatly improved these parameters
compared to the AlCl3 group. Al influences the Aβ aggregation and
plaque formation, which in turn interferes to and disrupts the
membrane structure. The results also showed a marked increase in
the β-parallel and antiparallel structure, that characterize the Aβ
formation in Al-induced AD hippocampal brain tissue, indicated by
the detected increase in both amide I sub-bands around 1674, 1692
cm-1. This drastic increase in Aβ formation was greatly reduced in the
curative and protective groups compared to the AlCl3 group and
approached nearly the control values. These results supported too by
the light microscope. AlCl3 group showed significant marked
degenerative changes in hippocampal neurons. Most cells appeared
small, shrieked and deformed. Interestingly, the administration of LS
in curative and protective groups markedly decreases the amount of
degenerated cells compared to the non-treated group. In addition, the
intensity of congo red stained cells was decreased. Hippocampal
neurons looked more/or less similar to those of control. This study showed a promising therapeutic effect of Lipidium
sativum group (LS) on AD rat model that seriously overcome the
signs of oxidative stress on membrane lipid and restore the protein
misfolding.
Abstract: Lagos urban mini bus drivers play a critical role in the
transportation sector. The current major mode of transportation
within Lagos metropolis remains road transportation and this
confirms the relevance of urban mini-bus drivers in transporting the
populace to their various destinations. Other modes of transportation
such as the train and waterways are currently inadequate. Various
threats to the well-being of urban bus drivers include congested
traffic typical of modern day lifestyles, dwindling financial returns
due to long hours in traffic, fewer hours of sleep, inadequate diet,
time pressure, and assaults related to fare disputes. Several healthrelated
problems have been documented to be associated with urban
bus driving. For instance, greater rates of hypertension, obesity and
cholesterol level have been reported. Research studies are yet to
identify the influence of age and marital status on the well-being of
urban mini-bus drivers in Lagos metropolis. A study of this nature is
necessary as it is culturally perceived in Nigeria that older and
married people are especially influenced by family affiliation and
would behave in ways that would project positive outcomes. The
study sample consisted of 150 urban mini-bus drivers who were
conveniently sampled from six (6) different terminuses where their
journey begins and terminates. The well-being questionnaire was
administered to participants. The criteria for inclusion in the study
included the ability to read in English language and the confirmation
that interested participants were on duty and suited to be driving
mini-buses. Due to the nature of the job of bus driving, the researcher
administered the questionnaires on participants who were free and
willing to respond to the survey. All participants were males of
various age groups and of different marital statuses. Results of
analyses conducted revealed no significant influence of age and
marital status on the well-being of urban mini-bus drivers. This
indicates that the well-being of urban mini bus drivers is not
influenced by age or marital status. The findings of this study have
cultural implications. It negates the popularly held belief that older
and married people care more about their well-being than younger
and single people. It brings to fore the need to also identify and
consider other factors when certifying people for the job of urban bus
driving.
Abstract: This study was aimed to measure effective transverse
relaxation rates (R2*) in the liver and muscle of normal New Zealand
White (NZW) rabbits. R2* relaxation rate has been widely used in
various hepatic diseases for iron overload by quantifying iron contents
in liver. R2* relaxation rate is defined as the reciprocal of T2*
relaxation time and mainly depends on the constituents of tissue.
Different tissues would have different R2* relaxation rates. The signal
intensity decay in Magnetic resonance imaging (MRI) may be
characterized by R2* relaxation rates. In this study, a 1.5T GE Signa
HDxt whole body MR scanner equipped with an 8-channel high
resolution knee coil was used to observe R2* values in NZW rabbit’s
liver and muscle. Eight healthy NZW rabbits weighted 2 ~ 2.5 kg were
recruited. After anesthesia using Zoletil 50 and Rompun 2% mixture,
the abdomen of rabbit was landmarked at the center of knee coil to
perform 3-plane localizer scan using fast spoiled gradient echo
(FSPGR) pulse sequence. Afterwards, multi-planar fast gradient echo
(MFGR) scans were performed with 8 various echo times (TEs) to
acquire images for R2* measurements. Regions of interest (ROIs) at
liver and muscle were measured using Advantage workstation.
Finally, the R2* was obtained by a linear regression of ln(sı) on TE.
The results showed that the longer the echo time, the smaller the signal
intensity. The R2* values of liver and muscle were 44.8 ± 10.9 s-1 and
37.4 ± 9.5 s-1, respectively. It implies that the iron concentration of
liver is higher than that of muscle. In conclusion, the more the iron
contents in tissue, the higher the R2*. The correlations between R2*
and iron content in NZW rabbits might be valuable for further
exploration.
Abstract: Various nanomaterials can be used as a drug delivery
vehicles in nanomedicine, called nanocarriers. They can either be
organic or inorganic, synthetic or natural-based. Although synthetic
nanocarriers are easier to produce, they can often be toxic for the
organism and thus not suitable for use in treatment. From naturalbased
nanocarriers, the most commonly used are protein cages or
viral capsids. In this work, virus bacteriophage λ was used for
delivery of different cytotoxic drugs (cisplatin, carboplatin,
oxaliplatin and doxorubicin). Large quantities of phage λ were
obtained from phage λ-producing strain of E. coli cultivated in
medium with 0.2% maltose. After killing of E. coli with chloroform
and its removal by centrifugation, the phage was concentrated by
ultracentrifugation at 130 000×g and 4°C for 3 h. The encapsulation
of the drugs was performed by infusion method and four different
concentrations of the drugs were encapsulated (200; 100; 50; 25
μg·mL-1). Free drug molecules were removed by filtration. The
encapsulation was verified using the absorbance for doxorubicin and
atomic absorption spectrometry for platinum cytostatics. The amount
of encapsulated drug linearly increased with the increasing
concentration of applied drug with the determination coefficient
R2=0.989 for doxorubicin; R2=0.967 for cisplatin; R2=0.989 for
carboplatin and R2=0.996 for oxaliplatin. The overall encapsulation
efficiency was calculated as 50% for doxorubicin; 8% for cisplatin;
6% for carboplatin and 10% for oxaliplatin.
Abstract: According to IR, 13C and 1H NMR, APT, 1D NOE,
2D heteronuclear 1H/13C HSQC and 2D DOSY experiments the main
chemical constituent of high-molecular preparations from Symphytum
asperum, S. caucasicum, S. officinale and Anchusa italica
(Boraginaceae) was found to be caffeic acid-derived polyether,
namely poly[3-(3,4-dihydroxyphenyl)glyceric acid] (PDPGA) or
poly[oxy-1-carboxy-2-(3,4-dihydroxyphenyl)ethylene]. Most
carboxylic groups of this polymer of A. italica are methylated.
Abstract: Millions of girls are forcibly married during the
transitional period between puberty and adulthood. At a stage of
vulnerability cultural practices, religious rights and social standards
place her in a position where she is catapult into womanhood. An
advocate against forced child marriage could argue that child rights,
cultural rights, religious rights, right to marry, right to life, right to
health, right to education, right to be free from slavery, right to be
free from torture, right to consent to marriage are all violated by the
practice of child marriage. The author is this advocate and this paper
will present how some of these rights are violated and establish the
need for change.
Abstract: Noninvasive diagnostics of diseases via breath
analysis has attracted considerable scientific and clinical interest for
many years and become more and more promising with the rapid
advancements in nanotechnology and biotechnology. The volatile
organic compounds (VOCs) in exhaled breath, which are mainly
blood borne, particularly provide highly valuable information about
individuals’ physiological and pathophysiological conditions.
Additionally, breath analysis is noninvasive, real-time, painless, and
agreeable to patients. We have developed a wireless sensor array
based on single-stranded DNA (ssDNA)-functionalized single-walled
carbon nanotubes (SWNT) for the detection of a number of
physiological indicators in breath. Seven DNA sequences were used
to functionalize SWNT sensors to detect trace amount of methanol,
benzene, dimethyl sulfide, hydrogen sulfide, acetone, and ethanol,
which are indicators of heavy smoking, excessive drinking, and
diseases such as lung cancer, breast cancer, and diabetes. Our test
results indicated that DNA functionalized SWNT sensors exhibit
great selectivity, sensitivity, and repeatability; and different
molecules can be distinguished through pattern recognition enabled
by this sensor array. Furthermore, the experimental sensing results
are consistent with the Molecular Dynamics simulated ssDNAmolecular
target interaction rankings. Thus, the DNA-SWNT sensor
array has great potential to be applied in chemical or biomolecular
detection for the noninvasive diagnostics of diseases and personal
health monitoring.
Abstract: High Performance Liquid Chromatography (HPLC)
method was developed and validated for simultaneous estimation of
6-Gingerol(6G) and 6-Shogaol(6S) in joint pain relief gel containing
ginger extract. The chromatographic separation was achieved by
using C18 column, 150 x 4.6mm i.d., 5μ Luna, mobile phase
containing acetonitrile and water (gradient elution). The flow rate
was 1.0 ml/min and the absorbance was monitored at 282 nm. The
proposed method was validated in terms of the analytical parameters
such as specificity, accuracy, precision, linearity, range, limit of
detection (LOD), limit of quantification (LOQ), and determined
based on the International Conference on Harmonization (ICH)
guidelines. The linearity ranges of 6G and 6S were obtained over 20-
60 and 6-18 μg/ml respectively. Good linearity was observed over the
above-mentioned range with linear regression equation Y= 11016x-
23778 for 6G and Y = 19276x-19604 for 6S (x is concentration of
analytes in μg/ml and Y is peak area). The value of correlation
coefficient was found to be 0.9994 for both markers. The limit of
detection (LOD) and limit of quantification (LOQ) for 6G were
0.8567 and 2.8555 μg/ml and for 6S were 0.3672 and 1.2238 μg/ml
respectively. The recovery range for 6G and 6S were found to be
91.57 to 102.36 % and 84.73 to 92.85 % for all three spiked levels.
The RSD values from repeated extractions for 6G and 6S were 3.43
and 3.09% respectively. The validation of developed method on
precision, accuracy, specificity, linearity, and range were also
performed with well-accepted results.
Abstract: This research paper portrays a comparative analysis of
thermomechanical behaviour of Shielded Metal Arc Welding
(SMAW) and Gas Tungsten Arc Welding (GTAW) of low carbon
steel of AISI 1020 grade butt joints. The thermal history has been
obtained by experimental work. We have focused on temperature
dependent cooling rate as depicted by Adam’s two-dimensional
model. The effect of moving point heat source of SMAW and GTAW
on mechanical properties has been judged by optical and scanning
electron micrographs of different regions in weld joints. The
microhardness study has been carried to visualize the joint strength
due to formation of different phases.
Abstract: The effects of the contact ball-lens on the soda lime
glass in laser thermal cleavage with a cw Nd-YAG laser were
investigated in this study. A contact ball-lens was adopted to generate
a bending force on the crack formation of the soda-lime glass in the
laser cutting process. The Nd-YAG laser beam (wavelength of 1064
nm) was focused through the ball-lens and transmitted to the soda-lime
glass, which was coated with a carbon film on the surface with a
bending force from a ball-lens to generate a tensile stress state on the
surface cracking. The fracture was controlled by the contact ball-lens
and a straight cutting was tested to demonstrate the feasibility.
Experimental observations on the crack propagation from the leading
edge, main section and trailing edge of the glass sheet were compared
with various mechanical and thermal loadings. Further analyses on the
stress under various laser powers and contact ball loadings were made
to characterize the innovative technology. The results show that the distributions of the side crack at the
leading and trailing edges are mainly dependent on the boundary
condition, contact force, cutting speed and laser power. With the
increase of the mechanical and thermal loadings, the region of the side
cracks might be dramatically reduced with proper selection of the
geometrical constrains. Therefore the application of the contact
ball-lens is a possible way to control the fracture in laser cleavage with
improved cutting qualities.
Abstract: The plastic industry plays very important role in the
economy of any country. It is generally among the leading share of
the economy of the country. Since metals and their alloys are very
rarely available on the earth. Therefore, to produce plastic products
and components, which finds application in many industrial as well
as household consumer products is beneficial. Since 50% plastic
products are manufactured by injection moulding process. For
production of better quality product, we have to control quality
characteristics and performance of the product. The process
parameters plays a significant role in production of plastic, hence the
control of process parameter is essential. In this paper the effect of
the parameters selection on injection moulding process has been
described. It is to define suitable parameters in producing plastic
product. Selecting the process parameter by trial and error is neither
desirable nor acceptable, as it is often tends to increase the cost and
time. Hence, optimization of processing parameter of injection
moulding process is essential. The experiments were designed with
Taguchi’s orthogonal array to achieve the result with least number of
experiments. Plastic material polypropylene is studied. Tensile
strength test of material is done on universal testing machine, which
is produced by injection moulding machine. By using Taguchi
technique with the help of MiniTab-14 software the best value of
injection pressure, melt temperature, packing pressure and packing
time is obtained. We found that process parameter packing pressure
contribute more in production of good tensile plastic product.
Abstract: Fading noise degrades the performance of cellular
communication, most notably in femto- and pico-cells in 3G and 4G
systems. When the wireless channel consists of a small number of
scattering paths, the statistics of fading noise is not analytically
tractable and poses a serious challenge to developing closed
canonical forms that can be analysed and used in the design of
efficient and optimal receivers. In this context, noise is multiplicative
and is referred to as stochastically local fading. In many analytical
investigation of multiplicative noise, the exponential or Gamma
statistics are invoked. More recent advances by the author of this
paper utilized a Poisson modulated-weighted generalized Laguerre
polynomials with controlling parameters and uncorrelated noise
assumptions. In this paper, we investigate the statistics of multidiversity
stochastically local area fading channel when the channel
consists of randomly distributed Rayleigh and Rician scattering
centers with a coherent Nakagami-distributed line of sight component
and an underlying doubly stochastic Poisson process driven by a
lognormal intensity. These combined statistics form a unifying triply
stochastic filtered marked Poisson point process model.
Abstract: Sub-Saharan Africa is described as the second fastest
growing in mobile phone penetration in the world more than in the
United States or the European Union. Mobile phones have been used
to provide a lot of opportunities to improve people’s lives in the
region such as in banking, marketing, entertainment, and paying for
various bills such as water, TV, and electricity. However, the
potential of mobile phones to enhance teaching and learning has not
been explored. This study presents an experience of developing and
delivering SMS based quiz questions used to assess mastery of
subject content knowledge of science and mathematics secondary
school teachers in Tanzania. The SMS quizzes were used as a follow
up support mechanism to 500 teachers who participated in a project
to upgrade subject content knowledge of teachers in science and
mathematics subjects in Tanzania. Quizzes of 10-15 questions were
sent to teachers each week for 8 weeks and the results were analyzed
using SPSS. Results show that teachers who participated in chemistry
and biology subjects have better performance compared to those who
participated in mathematics and physics subjects. Teachers reported
some challenges that led to poor performance, This research has
several practical implications for those who are implementing or
planning to use mobile phones in teaching and learning especially in
rural secondary schools in sub-Saharan Africa.
Abstract: This paper focuses on the questions raised through the
work of Unit 5: ‘In/Out Crisis, emergent and adaptive’; an
architectural research-based studio at [ARC] University of Nicosia. Students were asked to delve into state of Art Technologies in
order to propose sustainable Emergent and Adaptive Architectures
and Urbanities, the resulting unprecedented spatial conditions and
atmospheres of the emergent new ways of living are deemed to be the
ultimate aim of the investigation. Students explored a variety of sites
and crisis conditions seen through their primary ingredient identified
as soil, water and air and their paired combination. Within this
methodology, crisis is seen as a mechanism for allowing an
emergence of new and fascinating ultimate sustainable future cultures
and cities by taking advantage of the primary materiality of the sites.
Abstract: The paper will focus on the strategic development
deriving from the evolution of the traditional courtyard spatial
organization towards a new, contemporary sustainable way of living.
New sustainable approaches that engulf the social issues, the notion
of place, the understanding of weather architecture blended together
with the bioclimatic behavior will be seen through a series of
experimental case studies in the island of Cyprus, inspired and
originated from its traditional wisdom, ranging from small scale of
living to urban interventions. Weather and nature will be seen as co-architectural authors with
architects. Furthermore, the building will be seen not as an object but
rather as a vessel of human activities. This will further enhance the
notion of merging the material and immaterial, the built and unbuilt,
subject-human, and the object-building. This eventually will enable
to generate the discussion of the understanding of the building in
relation to the place and its inhabitants, where the human topography
is more important than the material topography. The specificities of
the divided island and the dealing with sites that are in vicinity with
the diving Green Line will further trigger explorations dealing with
the regeneration issues and the social sustainability offering
unprecedented opportunities for innovative sustainable ways of
living. Opening up a discourse with premises of weather-nature, materialimmaterial,
human-material topographies in relation to the contested
sites of the borders will lead us to develop innovative strategies for a
profound, both technical and social sustainability, which fruitfully
yields to innovative living built environments, responding to the ever
changing environmental and social needs. As a starting point, a case study in Kaimakli in Nicosia, a
refurbishment with an extension of a traditional house, already
engulfs all the traditional/ vernacular wisdom of the bioclimatic
architecture. The project focusses on the direct and quite obvious
bioclimatic features such as south orientation and cross ventilation.
Furthermore, it tries to reinvent the adaptation of these parameters in
order to turn the whole house to a contemporary living environment.
In order to succeed this, evolutions of traditional architectural
elements and spatial conditions are integrated in a way that does not
only respond to some certain weather conditions, but they integrate
and blend the weather within the built environment. A series of
innovations aiming at maximum flexibility is proposed. The house
can finally be transformed into a winter enclosure, while for the most
part of the year it turns into a ‘camping’ living environment. Parallel to experimental interventions in existing traditional units,
we will proceed examining the implementation of the same
developed methodology in designing living units and complexes.
Malleable courtyard organizations that attempt to blend the
traditional wisdom with the contemporary needs for living, the
weather and nature with the built environment will be seen tested in
both horizontal and vertical developments. Social activities are seen as directly affected and forged by the
weather conditions thus generating a new social identity of people where people are directly involved and interacting with the weather.
The human actions and interaction with the built, material
environment in order to respond to weather will be seen as the result
of balancing the social with the technological sustainability, the
immaterial, and the material aspects of the living environment.
Abstract: Internal circulation two-platen clamping system for
injection molding machine (IMM) has many potential advantages on
energy-saving. In order to estimate its properties, experiments were
carried out in this paper. Displacement and pressure of the components
were measured. In comparison, the model of hydraulic clamping
system was established by using AMESim. The related parameters as
well as the energy consumption could be calculated. According to the
analysis, the hydraulic system was optimized in order to reduce the
energy consumption.
Abstract: Experience is what makes a man perfect. Though we
tend to learn many a different things in life through practice still we
need to go an extra mile to gain experience which would be profitable
only when it is integrated with regular practice. A clear phenomenal
idea is that every teacher is a learner. The centralized idea of this paper would focus on the integrated
practices carried out among the students of Jizan University which
enhances learning through experiences. Integrated practices like
student-directed activities, balanced curriculum, phonological based
activities and use of consistent language would enlarge the vision and
mission of students to earn experience through learning. Students
who receive explicit instruction and guidance could practice the skills
and strategies through student-directed activities such as peer tutoring
and cooperative learning. The second effective practice is to use
consistent language. Consistent language provides students a model
for talking about the new concepts which also enables them to
communicate without hindrances. Phonological awareness is an
important early reading skill for all students. Students generally have
phonemic awareness in their home language can often transfer that
knowledge to a second language. And also a balanced curriculum
requires instruction in all the elements of reading. Reading is the
most effective skill when both basic and higher-order skills are
included on a daily basis. Computer based reading and listening skills
will empower students to understand language in a better way.
English language learners can benefit from sound reading instruction
even before they are fully proficient in English as long as the
instruction is comprehensible. Thus, if students have to be well
equipped in learning they should foreground themselves in various
integrated practices through multifarious experience for which
teachers are moderators and trainers. This type of learning prepares
the students for a constantly changing society which helps them to
meet the competitive world around them for better employability
fulfilling the vision and mission of the institution.