Abstract: Quality of 2D and 3D cross-sectional images produce
by Computed Tomography primarily depend upon the degree of
precision of primary and secondary X-Ray intensity detection.
Traditional method of primary intensity detection is apt to errors.
Recently the X-Ray intensity measurement system along with smart
X-Ray sensors is developed by our group which is able to detect
primary X-Ray intensity unerringly. In this study a new smart X-Ray
sensor is developed using Light-to-Frequency converter TSL230
from Texas Instruments which has numerous advantages in terms of
noiseless data acquisition and transmission. TSL230 construction is
based on a silicon photodiode which converts incoming X-Ray
radiation into the proportional current signal. A current to frequency
converter is attached to this photodiode on a single monolithic CMOS
integrated circuit which provides proportional frequency count to
incoming current signal in the form of the pulse train. The frequency
count is delivered to the center of PICDEM FS USB board with
PIC18F4550 microcontroller mounted on it. With highly compact
electronic hardware, this Demo Board efficiently read the smart
sensor output data. The frequency output approaches overcome
nonlinear behavior of sensors with analog output thus un-attenuated
X-Ray intensities could be measured precisely and better
normalization could be acquired in order to attain high resolution.
Abstract: In this work study the location of interface in a stirred vessel with a Concave impeller by computational fluid dynamic was presented. To modeling rotating the impeller, sliding mesh (SM) technique was used and standard k-ε model was selected for turbulence closure. Mean tangential, radial and axial velocities and also turbulent kinetic energy (k) and turbulent dissipation rate (ε) in various points of tank was investigated. Results show sensitivity of system to location of interface and radius of 7 to 10cm for interface in the vessel with existence characteristics cause to increase the accuracy of simulation.
Abstract: We introduce an adaptive technique for the joint mitigation of transients and continuous-wave radio-frequency co-channel interference (CW RFI) in high-frequency (HF) over-the-horizon radars (OTHRs). The performance of this technique is illustrated using data from an operational surface-wave radar (SECAR) and from recent experimental trials with sky-wave (SW) and sky-wave–line-of-sight (SKYLOS) HF OTHRs.
Abstract: Particle boards were prepared from Maize cob (MC) and urea-formaldehyde resin (UFR) on compression moulding machine. The amount of MC was varied from 50-120g while 30g of UFR was kept constant. Some mechanical properties of the particle boards were tested using the standard ASM methods. The results show that as the MC content increased from 50- 120g in 30g UFR, the hardness increased from about 6.89 x 102 to7.51 x 102MPa. Impact strength decreased from 3.3x 10-2 to 0.45 x 10-2J/M2, while tensile strength initially increased from 2.63 x 102 to 3.14 x 102 MPa as the MC increased from 50 to 60g in 30g UFR, thereafter, it decreased to about 1.35 x 102MPa at 120g in 30g content.
Abstract: Pretreatment of oil palm empty fruit bunch (OPEFB) with N-Methylmorpholine-N-oxide (NMMO) to enhance biogas production was investigated. The pretreatments were performed at 90 and 120ºC for 1, 3, and 5 h using three different concentrations of NMMO of 73%, 79%, and 85%. The pretreated OPEFB was subsequently anaerobically digested to produce biogas. After pretreatment, there were no significant changes of the main composition of OPEFB and the maximum total solid recovery was 92%. The amorphous phase was increased up to 78% at pretreatment condition using 85% NMMO solution for 3 h at 120oC. In general, higher concentration of NMMO and higher temperature resulted in increased amorphous form and higher biogas production. The best results of biogas production reached enhancement of methane yield of 148% compared to the untreated OPEFB and increased in digestion of 94% compared to starch as reference.
Abstract: Differentiated impact of team sports (basketball, indoor soccer, handball) on general haemodynamics and aerobic potential of students who specialize in technical subjects is detected only on the fourth year of studies in the institute of higher education. Those who play basketball and indoor soccer have shown increase of stroke and minute volume of blood indices, pumping and contractile function of the heart, oxygenation of blood and oxygen delivery to tissues, aerobic energy supply and balance of sympathetic and parasympathetic activity of the nervous regulation mechanism of the circulatory system. Those who play handball have shown these indices statistically decreased. On the whole playing basketball and indoor soccer optimizes the strategy for adaptation of students to the studying process, but playing handball does the opposite thing. The leading factor for adaptation of students is: those who play basketball have increase of minute blood volume which stipulates velocity of the system blood circulation and well-timed oxygen delivery to tissues; those who play indoor soccer have increase of power and velocity of contractile function of the heart; those who play handball have increase of resistance of thorax to the system blood flow which minimizes contractile function of the heart, blood oxygen saturation and delivery of oxygen to tissues.
Abstract: The use of renewable energy sources becomes more
necessary and interesting. As wider applications of renewable energy
devices at domestic, commercial and industrial levels has not only
resulted in greater awareness, but also significantly installed
capacities. In addition, biomass principally is in the form of woods,
which is a form of energy by humans for a long time. Gasification is
a process of conversion of solid carbonaceous fuel into combustible
gas by partial combustion. Many gasifier models have various
operating conditions; the parameters kept in each model are different.
This study applied experimental data, which has three inputs, which
are; biomass consumption, temperature at combustion zone and ash
discharge rate. One output is gas flow rate. For this paper, neural
network was used to identify the gasifier system suitable for the
experimental data. In the result,neural networkis usable to attain the
answer.
Abstract: In July 2012, an indoor/outdoor monitoring
programme was undertaken in two university sports facilities: a
fronton and a gymnasium. Comfort parameters (temperature, relative
humidity, CO and CO2) and total volatile organic compounds
(VOCs) were continuously monitored. Concentrations of NO2,
carbonyl compounds and individual VOCs were obtained. Low
volume samplers were used to collect particulate matter (PM10). The
minimum ventilation rates stipulated for acceptable indoor air quality
were observed in both sports facilities. It was found that cleaning
activities may have a large influence on the VOC levels. Acrolein
was one of the most abundant carbonyl compounds, showing
concentrations above the recommended limit. Formaldehyde was
detected at levels lower than those commonly reported for other
indoor environments. The PM10 concentrations obtained during the
occupancy periods ranged between 38 and 43μgm-3 in the fronton and
from 154 to 198μgm-3 in the gymnasium.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: The microbiological and physicochemical
characteristics of wetland soils in Eket Local Government Area were
studied between May 2001 and June 2003. Total heterotrophic
bacterial counts (THBC), total fungal counts (TFC), and total
actinomycetes counts (TAC) were determined from soil samples
taken from four locations at two depths in the wet and dry seasons.
Microbial isolates were characterized and identified. Particle size and
chemical parameters were also determined using standard methods.
THBC ranged from 5.2 (+0.17) x106 to 1.7 (+0.18) x107 cfu/g and
from 2.4 (+0.02) x106 to 1.4 (+0.04) x107cfu/g in the wet and dry
seasons, respectively. TFC ranged from 1.8 (+0.03) x106 to 6.6 (+
0.18) x106 cfu/g and from 1.0 (+0.04) x106 to 4.2 (+ 0.01) x106 cfu/g
in the wet and dry seasons, respectively .TAC ranged from 1.2
(+0.53) x106 to 6.0 (+0.05) x106 cfu/g and from 0.6 (+0.01) x106 to
3.2 (+ 0.12) x106 cfu/g in the wet and dry season, respectively.
Acinetobacter, Alcaligenes, Arthrobacter, Bacillus, Beijerinckja,
Enterobacter, Micrococcus, Flavobacterium, Serratia, Enterococcus,
and Pseudomonas species were predominant bacteria while
Aspergillus, Fusarium, Mucor, Penicillium, and Rhizopus were the
dominant fungal genera isolated. Streptomyces and Norcadia were
the actinomycetes genera isolated. The particle size analysis showed
high sand fraction but low silt and clay. The pH and % organic
matter were generally acidic and low, respectively at all locations.
Calcium dominated the exchangeable bases with low electrical
conductivity and micronutrients. These results provide the baseline
data of Eket wetland soils for its management for sustainable
agriculture.
Abstract: The paper presents a technique suitable in robot
vision applications where it is not possible to establish the object position from one view. Usually, one view pose calculation methods
are based on the correspondence of image features established at a
training step and exactly the same image features extracted at the
execution step, for a different object pose. When such a
correspondence is not feasible because of the lack of specific features
a new method is proposed. In the first step the method computes
from two views the 3D pose of feature points. Subsequently, using a
registration algorithm, the set of 3D feature points extracted at the execution phase is aligned with the set of 3D feature points extracted
at the training phase. The result is a Euclidean transform which have
to be used by robot head for reorientation at execution step.
Abstract: Flour from Mucuna beans (Mucuna pruriens) were
used in producing texturized meat analogue using a single screw
extruder to monitor modifications on the proximate composition and
the functional properties at high moisture level. Response surface
methodology based on Box Behnken design at three levels of barrel
temperature (110, 120, 130°C), screw speed (100,120,140rpm) and
feed moisture (44, 47, 50%) were used in 17 runs. Regression models
describing the effect of variables on the product responses were
obtained. Descriptive profile analyses and consumer acceptability
test were carried out on optimized flavoured extruded meat analogue.
Responses were mostly affected by barrel temperature and moisture
level and to a lesser extent by screw speed. Optimization results
based on desirability concept indicated that a barrel temperature of
120.15°C, feed moisture of 47% and screw speed of 119.19 rpm
would produce meat analogue of preferable proximate composition,
functional and sensory properties which reveals consumers` likeness
for the product.
Abstract: Periodic vortex shedding in pulsating flow inside wavy
channel and the effect it has on heat transfer are studied using the
finite volume method. A sinusoidally-varying component is superimposed
on a uniform flow inside a sinusoidal wavy channel and
the effects on the Nusselt number is analyzed. It was found that a
unique optimum value of the pulsation frequency, represented by the
Strouhal number, exists for Reynolds numbers ranging from 125 to
1000. Results suggest that the gain in heat transfer is related to the
process of vortex formation, movement about the troughs of the wavy
channel, and subsequent ejection/destruction through the converging
section. Heat transfer is the highest when the frequencies of the
pulsation and vortex formation approach being in-phase. Analysis of
Strouhal number effect on Nu over a period of pulsation substantiates
the proposed physical mechanism for enhancement. The effect of
changing the amplitude of pulsation is also presented over a period
of pulsation, showing a monotonic increase in heat transfer with
increasing amplitude. The 60% increase in Nusselt number suggests
that sinusoidal fluid pulsation can an effective method for enhancing
heat transfer in laminar, wavy-channel flows.
Abstract: Uterine and oviducal fluids are necessary for
capacitation of the spermatozoa and early embryonic development.
The aim of the present study was to determine the effects of estrous
cycle phases (follicular and luteal) on some biological parameters
(enzymes, electrolytes and total proteins) in uterine and oviducal
secretions of ewes. Oviducal and uterine fluids were collected,
diluted and centrifuged. According to our results, concentrations of
GPT, G6PDH, total proteins, K and Na were significantly (P
Abstract: Asiatic Houbara ( Chlamydotis macqueenii ) is a
flagship and vulnerable species. In-situ conservation of this
threatened species demands for knowledge of its habitat selection.
The aim of this study was to determine habitat variables influencing
birds wintering and breeding selection in semi- arid central Iran.
Habitat features of the detected nest and pellet sites were compared
with paired and random plots by quantifying a number of habitat
variables. In wintering habitat use at micro scale houbara selected
sites where vegetation cover was significantly lower compard to
control sites( p< 0.001). Areas with low number of larger plant
species (p=0.03) that were not too close to a vegetation
patch(p
Abstract: This study presents the performance of membrane
bioreactor in treating high phosphate wastewater. The laboratory
scale MBR was operated at permeate flux of 25 L/m2.h with a hollow
fiber membrane (polypropylene, approx. pore size 0.01 - 0.2 μm) at
hydraulic retention time (HRT) of 12 hrs. Scanning electron
microscopy (SEM) and energy diffusive X-ray (EDX) analyzer were
used to characterize the membrane foulants. Results showed that the
removal efficiencies of COD, TSS, NH3-N and PO4
3- were 93, 98, 80
and 30% respectively. On average 91% of influent soluble microbial
products (SMP) were eliminated, with the eliminations of
polysaccharides mostly above 80%. The main fouling resistance was
cake resistance. It should be noted that SMP were found in major
portions of mixed liquor that played a relatively significant role in
membrane fouling. SEM and EDX analyses indicated that the
foulants covering the membrane surfaces comprises not only organic
substances but also inorganic elements including Mg, Ca, Al, K and
P.
Abstract: Plasmodium vivax malaria differs from P. falciparum malaria in that a person suffering from P. vivax infection can suffer relapses of the disease. This is due the parasite being able to remain dormant in the liver of the patients where it is able to re-infect the patient after a passage of time. During this stage, the patient is classified as being in the dormant class. The model to describe the transmission of P. vivax malaria consists of a human population divided into four classes, the susceptible, the infected, the dormant and the recovered. The effect of a time delay on the transmission of this disease is studied. The time delay is the period in which the P. vivax parasite develops inside the mosquito (vector) before the vector becomes infectious (i.e., pass on the infection). We analyze our model by using standard dynamic modeling method. Two stable equilibrium states, a disease free state E0 and an endemic state E1, are found to be possible. It is found that the E0 state is stable when a newly defined basic reproduction number G is less than one. If G is greater than one the endemic state E1 is stable. The conditions for the endemic equilibrium state E1 to be a stable spiral node are established. For realistic values of the parameters in the model, it is found that solutions in phase space are trajectories spiraling into the endemic state. It is shown that the limit cycle and chaotic behaviors can only be achieved with unrealistic parameter values.
Abstract: This paper presents a unified approach based graph
theory and system theory postulates for the modeling and analysis
of Simple open cycle Gas turbine system. In the present paper, the
simple open cycle gas turbine system has been modeled up to its subsystem
level and system variables have been identified to develop the
process subgraphs. The theorems and algorithms of the graph theory
have been used to represent behavioural properties of the system like
rate of heat and work transfers rates, pressure drops and temperature
drops in the involved processes of the system. The processes have
been represented as edges of the process subgraphs and their limits
as the vertices of the process subgraphs. The system across variables
and through variables has been used to develop terminal equations of
the process subgraphs of the system. The set of equations developed
for vertices and edges of network graph are used to solve the system
for its process variables.
Abstract: Although lots of experiments have been done in enhanced oil recovery, the number of experiments which consider the effects of local and global heterogeneity on efficiency of enhanced oil recovery based on the polymer-surfactant flooding is low and rarely done. In this research, we have done numerous experiments of water flooding and polymer-surfactant flooding on a five spot glass micromodel in different conditions such as different positions of layers. In these experiments, five different micromodels with three different pore structures are designed. Three models with different layer orientation, one homogenous model and one heterogeneous model are designed. In order to import the effect of heterogeneity of porous media, three types of pore structures are distributed accidentally and with equal ratio throughout heterogeneous micromodel network according to random normal distribution. The results show that maximum EOR recovery factor will happen in a situation where the layers are orthogonal to the path of mainstream and the minimum EOR recovery factor will happen in a situation where the model is heterogeneous. This experiments show that in polymer-surfactant flooding, with increase of angles of layers the EOR recovery factor will increase and this recovery factor is strongly affected by local heterogeneity around the injection zone.
Abstract: In this paper, the experimental design of using the
Taguchi method is employed to optimize the processing parameters in
the plasma arc surface hardening process. The processing parameters
evaluated are arc current, scanning velocity and carbon content of
steel. In addition, other significant effects such as the relation between
processing parameters are also investigated. An orthogonal array,
signal-to-noise (S/N) ratio and analysis of variance (ANOVA) are
employed to investigate the effects of these processing parameters.
Through this study, not only the hardened depth increased and surface
roughness improved, but also the parameters that significantly affect
the hardening performance are identified. Experimental results are
provided to verify the effectiveness of this approach.