Abstract: Hollow section for bridge columns has some
advantages. However, current seismic design codes do not provide
design regulations for hollow bridge piers. There have been many
experimental studied for hollow reinforced concrete piers in the world.
But, Study for hollow section for bridge piers in Korea has been begun
with approximately 2000s. There has been conducted experimental
study for hollow piers of flexural controlled sections by Yeungnam
University, Sung kyunkwan University, Korea Expressway
Corporation in 2009. This study concluded that flexural controlled
sections for hollow piers showed the similar behavior to solid sections.
And there have been conducted experimental study for hollow piers of
compression controlled sections by Yeungnam University, Korea
Institute of Construction Technology in 2012. This study concluded
that compression controlled sections for hollow piers showed
compression fracture of concrete in inside wall face. Samsung
Construction & Trading Corporation has been conducted study with
Yeungnam University for reduce the quantity of reinforcement details
about hollow piers. Reduce the quantity of reinforcement details are
triangular cross tie. This study concluded that triangular reinforcement
details showed the similar behavior as compared with existing
reinforcement details.
Abstract: Currently there are many use of threaded reinforcing
bars in construction fields because those do not need additional screw
processing when connecting reinforcing bar by threaded coupler. In
this study, reinforced concrete bridge piers using threaded rebar
coupler system at the plastic hinge area were tested to evaluate seismic
performance. The test results showed that threads of the threaded rebar
coupler system could be loosened while under tension-compression
cyclic loading because tolerance and rib face angle of a threaded rebar
coupler system are greater than that of a conventional ribbed rebar
coupler system. As a result, cracks were concentrated just outside of
the mechanical coupler and stiffness of reinforced concrete bridge pier
decreased. Therefore, it is recommended that connection ratio of
mechanical couplers in one section shall be below 50% in order that
cracks are not concentrated just outside of the mechanical coupler.
Also, reduced stiffness of the specimen should be considered when
using the threaded rebar coupler system.
Abstract: In order to manufacture short gap single Si nanowire
(NW) field effect transistor (FET) by imprinting and transferring
method, we introduce the method using Al2O3 sacrificial layer. The
diameters of cylindrical Si NW addressed between Au electrodes by
dielectrophoretic (DEP) alignment method are controlled to 106, 128,
and 148 nm. After imprinting and transfer process, cylindrical Si NW
is embedded in PVP adhesive and dielectric layer. By curing
transferred cylindrical Si NW and Au electrodes on PVP-coated p++ Si
substrate with 200nm-thick SiO2, 3μm gap Si NW FET fabrication
was completed. As the diameter of embedded Si NW increases, the
mobility of FET increases from 80.51 to 121.24 cm2/V·s and the
threshold voltage moves from –7.17 to –2.44 V because the ratio of
surface to volume gets reduced.
Abstract: This paper focuses on assessing sloshing-induced overflow of the seismically-isolated nuclear tanks based on Fluid-Structure Interaction (FSI) analysis. Typically, fluid motion in the seismically-isolated nuclear tank systems may be rather amplified and even overflowed under earthquake. Sloshing-induced overflow in those structures has to be reliably assessed and predicted since it can often cause critical damages to humans and environments. FSI analysis is herein performed to compute the total cumulative overflowed water volume more accurately, by coupling ANSYS with CFX for structural and fluid analyses, respectively. The approach is illustrated on a nuclear liquid storage tank, Spent Fuel Pool (SFP), forgiven conditions under consideration: different liquid levels, Peak Ground Accelerations (PGAs), and post earthquakes.
Abstract: The number of people using SNS with their mobile devices is soaring. This research focuses on the Twitter service that has the most third-party applications and delved into the fact that there were not sufficient studies on the UX design aspects of Twitter applications. Among social network services which have emerged as a major social topic lately, this research try to analyze the UX design of the Twitter application which is also called micro-blogging service. Therefore this research sets its goal to draw components of the UX design aspect of the Tweeter application on which there are not enough analysis yet. Moreover, this research suggests improvement of mobile application which will assure better users- experience. In order to analyze the UX design aspect of the mobile twitter application, with relevant document and user research, evaluating factors of the UX Design which would affect users- experience were organized. The subjects for cases were selected among six paid and free social networking applications that had been consistently ranked from 1st to 100th in the Korean application store during May, 2012 after closely monitoring the rank. From May 15th to May 11th in 2012, in accordance with the evaluating standard, surveys were conducted in a form of interviews with 20 subjects who have used the Twitter application to find out problems and solutions for the UX design of the mobile Twitter application.
Abstract: Antiseismic property of telecommunication equipment
is very important for the grasp of the damage and the restoration after
earthquake. Telecommunication business operators are regulating
seismic standard for their equipments. These standards are organized
to simulate the real seismic situations and usually define the minimum
value of first natural frequency of the equipments or the allowable
maximum displacement of top of the equipments relative to bottom.
Using the finite element analysis, natural frequency can be obtained
with high accuracy but the relative displacement of top of the
equipments is difficult to predict accurately using the analysis.
Furthermore, in the case of simulating the equipments with access
floor, predicting the relative displacement of top of the equipments
become more difficult.
In this study, using enormous experimental datum, an empirical
formula is suggested to forecast the relative displacement of top of the
equipments. Also it can be known that which physical quantities are
related with the relative displacement.
Abstract: The accuracy of estimated stability and control
derivatives of a light aircraft from flight test data were evaluated. The light aircraft, named ChangGong-91, is the first certified aircraft from
the Korean government. The output error method, which is a maximum likelihood estimation technique and considers measurement
noise only, was used to analyze the aircraft responses measures. The
multi-step control inputs were applied in order to excite the short period mode for the longitudinal and Dutch-roll mode for the lateral-directional motion. The estimated stability/control derivatives of Chan Gong-91 were analyzed for the assessment of handling
qualities comparing them with those of similar aircraft. The accuracy of the flight derivative estimates derived from flight test measurement
was examined in engineering judgment, scatter and Cramer-Rao bound, which turned out to be satisfactory with minor defects..
Abstract: In the stadium structure, the significant dynamic
responses such as resonance or similar behavior can be occurred by
spectator rhythmical activities. Thus, accurate analysis and precise
investigation of stadium structure that is subjected to dynamic loads
are required for practical design and serviceability check of stadium
structures. Moreover, it is desirable to measure and analyze the
dynamic loads of spectator activities because these dynamic loads can
not be easily expressed in numerical formula. In this study, various
dynamic loads induced by spectator movements are measured and
analyzed. These dynamic loads induced by spectators movement of
stadium structure can be classified into the impact load and the
periodic load. These dynamic loads can be expressed as Fourier
harmonic load. And, these dynamic loads could be applied for the
accurate vibration analysis of a stadium structure.
Abstract: This paper presents the design and implements the prototype of an intelligent data processing framework in ubiquitous sensor networks. Much focus is put on how to handle the sensor data stream as well as the interoperability between the low-level sensor data and application clients. Our framework first addresses systematic middleware which mitigates the interaction between the application layer and low-level sensors, for the sake of analyzing a great volume of sensor data by filtering and integrating to create value-added context information. Then, an agent-based architecture is proposed for real-time data distribution to efficiently forward a specific event to the appropriate application registered in the directory service via the open interface. The prototype implementation demonstrates that our framework can host a sophisticated application on the ubiquitous sensor network and it can autonomously evolve to new middleware, taking advantages of promising technologies such as software agents, XML, cloud computing, and the like.
Abstract: A talking head system (THS) is presented to animate
the face of a speaking 3D avatar in such a way that it realistically
pronounces the given Korean text. The proposed system consists of
SAPI compliant text-to-speech (TTS) engine and MPEG-4 compliant
face animation generator. The input to the THS is a unicode text that is
to be spoken with synchronized lip shape. The TTS engine generates a
phoneme sequence with their duration and audio data. The TTS
applies the coarticulation rules to the phoneme sequence and sends a
mouth animation sequence to the face modeler. The proposed THS can
make more natural lip sync and facial expression by using the face
animation generator than those using the conventional visemes only.
The experimental results show that our system has great potential for
the implementation of talking head for Korean text.
Abstract: Understanding road features such as lanes, the color
of lanes, and sidewalks in a live video captured from a moving
vehicle is essential to build video-based navigation systems. In this
paper, we present a novel idea to understand the road features using
support vector machines. Various feature vectors including color
components of road markings and the difference between two
regions, i.e., chosen AOIs, and so on are fed into SVM, deciding
colors of lanes and sidewalks robustly. Experimental results are
provided to show the robustness of the proposed idea.
Abstract: Image target detection and tracking methods based on
target information such as intensity, shape model, histogram and
target dynamics have been proven to be robust to target model
variations and background clutters as shown by recent researches.
However, no definitive answer has been given to occluded target by
counter measure or limited field of view(FOV). In this paper, we
will present a novel tracking method using filtering and computational
geometry. This paper has two central goals: 1) to deal with vulnerable
target measurements; and 2) to maintain target tracking out of FOV
using non-target-originated information. The experimental results,
obtained with airborne images, show a robust tracking ability with
respect to the existing approaches. In exploring the questions of target
tracking, this paper will be limited to consideration of airborne image.