Abstract: A two-dimensional numerical simulation of crossflow
around four cylinders in an in-line rectangular configuration is
studied by using the lattice Boltzmann method (LBM). Special
attention is paid to the effect of the spacing between the cylinders.
The Reynolds number ( Re ) is chosen to be e 100 R = and the
spacing ratio L / D is set at 0.5, 1.5, 2.5, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0
and 10.0. Results show that, as in the case of four cylinders in an inline
rectangular configuration , flow fields show four different
features depending on the spacing (single square cylinder, stable
shielding flow, wiggling shielding flow and a vortex shedding flow)
are observed in this study. The effects of spacing ratio on physical
quantities such as mean drag coefficient, Strouhal number and rootmean-
square value of the drag and lift coefficients are also presented.
There is more than one shedding frequency at small spacing ratios.
The mean drag coefficients for downstream cylinders are less than
that of the single cylinder for all spacing ratios. The present results
using the LBM are compared with some existing experimental data
and numerical studies. The comparison shows that the LBM can
capture the characteristics of the bluff body flow reasonably well and
is a good tool for bluff body flow studies.
Abstract: Developed tool is one of system tools for easier access to various scientific areas and real time interactive learning between
lecturer and for hearing impaired students. There is no demand for the lecturer to know Sign Language (SL). Instead, the new software
tools will perform the translation of the regular speech into SL, after
which it will be transferred to the student. On the other side, the
questions of the student (in SL) will be translated and transferred to
the lecturer in text or speech. One of those tools is presented tool. It-s
too for developing the correct Speech Visemes as a root of total communication method for hearing impared students.
Abstract: It has often been said that the strength of any country
resides in the strength of its industrial sector, and Progress in
industrial society has been accomplished by the creation of new
technologies. Developments have been facilitated by the increasing
availability of advanced manufacturing technology (AMT), in
addition the implementation of advanced manufacturing technology
(AMT) requires careful planning at all levels of the organization to
ensure that the implementation will achieve the intended goals.
Justification and implementation of advanced manufacturing
technology (AMT) involves decisions that are crucial for the
practitioners regarding the survival of business in the present days of
uncertain manufacturing world. This paper assists the industrial
managers to consider all the important criteria for success AMT
implementation, when purchasing new technology. Concurrently,
this paper classifies the tangible benefits of a technology that are
evaluated by addressing both cost and time dimensions, and the
intangible benefits are evaluated by addressing technological,
strategic, social and human issues to identify and create awareness of
the essential elements in the AMT implementation process and
identify the necessary actions before implementing AMT.
Abstract: Globalization and therefore increasing tight competition among companies, have resulted to increase the importance of making well-timed decision. Devising and employing effective strategies, that are flexible and adaptive to changing market, stand a greater chance of being effective in the long-term. In other side, a clear focus on managing the entire product lifecycle has emerged as critical areas for investment. Therefore, applying wellorganized tools to employ past experience in new case, helps to make proper and managerial decisions. Case based reasoning (CBR) is based on a means of solving a new problem by using or adapting solutions to old problems. In this paper, an adapted CBR model with k-nearest neighbor (K-NN) is employed to provide suggestions for better decision making which are adopted for a given product in the middle of life phase. The set of solutions are weighted by CBR in the principle of group decision making. Wrapper approach of genetic algorithm is employed to generate optimal feature subsets. The dataset of the department store, including various products which are collected among two years, have been used. K-fold approach is used to evaluate the classification accuracy rate. Empirical results are compared with classical case based reasoning algorithm which has no special process for feature selection, CBR-PCA algorithm based on filter approach feature selection, and Artificial Neural Network. The results indicate that the predictive performance of the model, compare with two CBR algorithms, in specific case is more effective.
Abstract: In this research a mathematical model for direct
oxidization of hydrogen sulfide into elemental sulfur in a fluidized
bed reactor with external circulation was developed. As the catalyst
is deactivated in the fluidized bed, it might be placed in a reduction
tank in order to remove sulfur through heating above its dew point.
The reactor model demonstrated via MATLAB software. It was
shown that variations of H2S conversion as well as; products formed
were reasonable in comparison with corresponding results of a fixed
bed reactor. Through analyzing results of this model, it became
possible to propose the main optimized operating conditions for the
process considered. These conditions included; the temperature range
of 100-130ºC and utilizing the catalyst as much as possible providing
the highest bed density respect to dimensions of bed, economical
aspects that the bed ever remained in fluidized mode. A high active
and stable catalyst under the optimum conditions exhibited 100%
conversion in a fluidized bed reactor.
Abstract: Macrophomina phaseolina is a devastating soil-borne
fungal plant pathogen that causes charcoal rot disease in many
economically important crops worldwide. So far, no registered
fungicide is available against this plant pathogen. This study was
planned to examine the antifungal activity of an allelopathic grass
Cenchrus pennisetiformis (Hochst. & Steud.) Wipff. for the
management of M. phaseolina isolated from cowpea [Vigna
unguiculata (L.) Walp.] plants suffering from charcoal rot disease.
Different parts of the plants viz. inflorescence, shoot and root were
extracted in methanol. Laboratory bioassays were carried out using
different concentrations (0, 0.5, 1.0, …, 3.0 g mL-1) of methanolic
extracts of the test allelopathic grass species to assess the antifungal
activity against the pathogen. In general, extracts of all parts of the
grass exhibited antifungal activity. All the concentrations of
methanolic extracts of shoot and root significantly reduced fungal
biomass by 20–73% and 40–80%, respectively. Methanolic shoot
extract was fractionated using n-hexane, chloroform, ethyl acetate
and n-butanol. Different concentrations of these fractions (3.125,
6.25, …, 200 mg mL-1) were analyzed for their antifungal activity.
All the concentrations of n-hexane fraction significantly reduced
fungal biomass by 15–96% over corresponding control treatments.
Higher concentrations (12.5–200 mg mL-1) of chloroform, ethyl
acetate and n-butanol also reduced the fungal biomass significantly
by 29–100%, 46–100% and 24–100%, respectively.
Abstract: Photo-crosslinked rice starch-based biodegradable
films were prepared by casting film-solution on leveled trays and
ultra violet (UV) irradiation was applied for 10 minute. The effect of
the content (3%, 6% and 9 wt. %)of photosensitiser (sodium
benzoate) on mechanical properties, water vapor permeability (WVP)
and structural properties of rice starch films were investigated. The
tensile strength increased while elongation at break and water
resistance properties of rice starch films decreased with addition and
increasing content of photosensitiser. The % crystallinity of rice
starch films were decreased when the content of photosensitiser
increased and UV were applied. The results showed that the
carboxylate group band of sodium benzoate was found in the FTIR
spectrum of rice starch films and found that incorporation of 6% of
photosensitiser into the films showed a higher absorption band of
resulted films. This result pointed out the highest interaction between
starch molecules was occurred.
Abstract: The gases generated in oil filled transformers can be
used for qualitative determination of incipient faults. The Dissolved
Gas Analysis has been widely used by utilities throughout the world
as the primarily diagnostic tool for transformer maintenance. In this
paper, various Artificial Intelligence Techniques that have been used
by the researchers in the past have been reviewed, some conclusions
have been drawn and a sequential hybrid system has been proposed.
The synergy of ANN and FIS can be a good solution for reliable
results for predicting faults because one should not rely on a single
technology when dealing with real–life applications.
Abstract: This paper deals with condition monitoring of electric switch machine for railway points. Point machine, as a complex electro-mechanical device, switch the track between two alternative routes. There has been an increasing interest in railway safety and the optimal management of railway equipments maintenance, e.g. point machine, in order to enhance railway service quality and reduce system failure. This paper explores the development of Kolmogorov- Smirnov (K-S) test to detect some point failures (external to the machine, slide chairs, fixing, stretchers, etc), while the point machine (inside the machine) is in its proper condition. Time-domain stator Current signatures of normal (healthy) and faulty points are taken by 3 Hall Effect sensors and are analyzed by K-S test. The test is simulated by creating three types of such failures, namely putting a hard stone and a soft stone between stock rail and switch blades as obstacles and also slide chairs- friction. The test has been applied for those three faults which the results show that K-S test can effectively be developed for the aim of other point failures detection, which their current signatures deviate parametrically from the healthy current signature. K-S test as an analysis technique, assuming that any defect has a specific probability distribution. Empirical cumulative distribution functions (ECDF) are used to differentiate these probability distributions. This test works based on the null hypothesis that ECDF of target distribution is statistically similar to ECDF of reference distribution. Therefore by comparing a given current signature (as target signal) from unknown switch state to a number of template signatures (as reference signal) from known switch states, it is possible to identify which is the most likely state of the point machine under analysis.
Abstract: Requirement engineering has been the subject of large
volume of researches due to the significant role it plays in the
software development life cycle. However, dynamicity of software
industry is much faster than advances in requirements engineering
approaches. Therefore, this paper aims to systematically review and
evaluate the current research in requirement engineering and identify
new research trends and direction in this field. In addition, various
research methods associated with the Evaluation-based techniques
and empirical study are highlighted for the requirements engineering
field. Finally, challenges and recommendations on future directions
research are presented based on the research team observations
during this study.
Abstract: Wireless sensor networks are consisted of hundreds or
thousands of small sensors that have limited resources.
Energy-efficient techniques are the main issue of wireless sensor
networks. This paper proposes an energy efficient agent-based
framework in wireless sensor networks. We adopt biologically
inspired approaches for wireless sensor networks. Agent operates
automatically with their behavior policies as a gene. Agent aggregates
other agents to reduce communication and gives high priority to nodes
that have enough energy to communicate. Agent behavior policies are
optimized by genetic operation at the base station. Simulation results
show that our proposed framework increases the lifetime of each node.
Each agent selects a next-hop node with neighbor information and
behavior policies. Our proposed framework provides self-healing,
self-configuration, self-optimization properties to sensor nodes.
Abstract: In recent years, the number of natural disasters in Laos has a trend to increase, especially the disaster of flood. To make a flood plan risk management in the future, it is necessary to understand and analyze the characteristics of the rainfall and Mekong River level data. To reduce the damage, this paper presents the flood risk analysis in Luangprabang and Vientiane, the prefecture of Laos. In detail, the relationship between the rainfall and the Mekong River level has evaluated and appropriate countermeasure for flood was discussed.
Abstract: The morphology, mineralogical and chemical
composition of a low-grade nickel ore from Mpumalanga, South
Africa, were studied by scanning electron microscope (SEM), X-ray
diffraction (XRD) and X-ray fluorescence (XRF), respectively. The
ore was subjected to atmospheric agitation leaching using sulphuric
acid to investigate the effects of acid concentration, leaching
temperature, leaching time and particle size on extraction of nickel
and cobalt. Analyses results indicated the ore to be a saprolitic nickel
laterite belonging to the serpentine group of minerals. Sulphuric acid
was found to be able to extract nickel from the ore. Increased acid
concentration and temperature only produced low amounts of nickel
but improved cobalt extraction. As high as 77.44% Ni was achieved
when leaching a -106+75μm fraction with 4.0M acid concentration at
25oC. The kinetics of nickel leaching from the saprolitic ore were
studied and the activation energy was determined to be 18.16kJ/mol.
This indicated that nickel leaching reaction was diffusion controlled.
Abstract: This paper proposed high level feature for online Lao handwritten recognition. This feature must be high level enough so that the feature is not change when characters are written by different persons at different speed and different proportion (shorter or longer stroke, head, tail, loop, curve). In this high level feature, a character is divided in to sequence of curve segments where a segment start where curve reverse rotation (counter clockwise and clockwise). In each segment, following features are gathered cumulative change in direction of curve (- for clockwise), cumulative curve length, cumulative length of left to right, right to left, top to bottom and bottom to top ( cumulative change in X and Y axis of segment). This feature is simple yet robust for high accuracy recognition. The feature can be gather from parsing the original time sampling sequence X, Y point of the pen location without re-sampling. We also experiment on other segmentation point such as the maximum curvature point which was widely used by other researcher. Experiments results show that the recognition rates are at 94.62% in comparing to using maximum curvature point 75.07%. This is due to a lot of variations of turning points in handwritten.
Abstract: In this paper, we show that the association of the PI
regulators for the speed and stator currents with a control strategy
using the linearization by state feedback for an induction machine
without speed sensor, and with an adaptation of the rotor resistance.
The rotor speed is estimated by using the model reference adaptive
system approach (MRAS). This method consists of using two
models: The first is the reference model and the second is an
adjustable one in which two components of the stator flux, obtained
from the measurement of the currents and stator voltages are
estimated. The estimated rotor speed is then obtained by canceling
the difference between stator-flux of the reference model and those
of the adjustable one. Satisfactory results of simulation are obtained
and discussed in this paper to highlight the proposed approach.
Abstract: This paper gives an overview of a deep drawing
process by pressurized liquid medium separated from the sheet by a
rubber diaphragm. Hydroforming deep drawing processing of sheet
metal parts provides a number of advantages over conventional
techniques. It generally increases the depth to diameter ratio possible
in cup drawing and minimizes the thickness variation of the drawn
cup. To explore the deformation mechanism, analytical and
numerical simulations are used for analyzing the drawing process of
an AA6061-T4 blank. The effects of key process parameters such as
coefficient of friction, initial thickness of the blank and radius
between cup wall and flange are investigated analytically and
numerically. The simulated results were in good agreement with the
results of the analytical model. According to finite element
simulations, the hydroforming deep drawing method provides a more
uniform thickness distribution compared to conventional deep
drawing and decreases the risk of tearing during the process.
Abstract: The intrusion detection problem has been frequently studied, but intrusion detection methods are often based on a single point of view, which always limits the results. In this paper, we introduce a new intrusion detection model based on the combination of different current methods. First we use a notion of distance to unify the different methods. Second we combine these methods using the Pearson correlation coefficients, which measure the relationship between two methods, and we obtain a combined distance. If the combined distance is greater than a predetermined threshold, an intrusion is detected. We have implemented and tested the combination model with two different public data sets: the data set of masquerade detection collected by Schonlau & al., and the data set of program behaviors from the University of New Mexico. The results of the experiments prove that the combination model has better performances.
Abstract: In this paper, fully developed flow and heat transfer of
viscoelastic materials in curved ducts with square cross section under
constant heat flux have been investigated. Here, staggered mesh is
used as computational grids and flow and heat transfer parameters
have been allocated in this mesh with marker and cell method.
Numerical solution of governing equations has being performed with
FTCS finite difference method. Furthermore, Criminale-Eriksen-
Filbey (CEF) constitutive equation has being used as viscoelastic
model. CEF constitutive equation is a suitable model for studying
steady shear flow of viscoelastic materials which is able to model
both effects of the first and second normal stress differences. Here, it
is shown that the first and second normal stresses differences have
noticeable and inverse effect on secondary flows intensity and mean
Nusselt number which is the main novelty of current research.
Abstract: The Deoxyribonucleic Acid (DNA) which is a doublestranded helix of nucleotides consists of: Adenine (A), Cytosine (C), Guanine (G) and Thymine (T). In this work, we convert this genetic code into an equivalent digital signal representation. Applying a wavelet transform, such as Haar wavelet, we will be able to extract details that are not so clear in the original genetic code. We compare between different organisms using the results of the Haar wavelet Transform. This is achieved by using the trend part of the signal since the trend part bears the most energy of the digital signal representation. Consequently, we will be able to quantitatively reconstruct different biological families.
Abstract: In this article, a mathematical programming model
for choosing an optimum portfolio of investments is developed.
The investments are considered as investment projects. The
uncertainties of the real world are associated through fuzzy
concepts for coefficients of the proposed model (i. e. initial
investment costs, profits, resource requirement, and total available
budget). Model has been coded by using LINGO 11.0 solver. The
results of a full analysis of optimistic and pessimistic derivative
models are promising for selecting an optimum portfolio of
projects in presence of uncertainty.