Abstract: Recently ORC(Organic Rankine Cycle) has attracted
much attention due to its potential in reducing consumption of fossil
fuels and its favorable characteristics to exploit low-grade heat sources.
In this work thermodynamic performance of ORC with superheating of
vapor is comparatively assessed for various working fluids. Special
attention is paid to the effects of system parameters such as the evaporating
temperature and the turbine inlet temperature on the characteristics
of the system such as maximum possible work extraction from
the given source, volumetric flow rate per 1 kW of net work and
quality of the working fluid at turbine exit as well as thermal and
exergy efficiencies. Results show that for a given source the thermal
efficiency increases with decrease of the superheating but exergy
efficiency may have a maximum value with respect to the superheating
of the working fluid. Results also show that in selection of working
fluid it is required to consider various criteria of performance characteristics
as well as thermal efficiency.
Abstract: Aerospace vehicles are subjected to non-uniform
thermal loading that may cause thermal buckling. A study was
conducted on the thermal post-buckling of shape memory alloy
composite plates subjected to the non-uniform tent-like temperature
field. The shape memory alloy wires were embedded within the
laminated composite plates to add recovery stress to the plates. The
non-linear finite element model that considered the recovery stress of
the shape memory alloy and temperature dependent properties of the
shape memory alloy and composite matrix along with its source
codes were developed. It was found that the post-buckling paths of
the shape memory alloy composite plates subjected to various tentlike
temperature fields were stable within the studied temperature
range. The addition of shape memory alloy wires to the composite
plates was found to significantly improve the post-buckling behavior
of laminated composite plates under non-uniform temperature
distribution.
Abstract: A low-complexity, high-accurate frequency offset
estimation for multi-band orthogonal frequency division multiplexing (MB-OFDM) based ultra-wide band systems is presented regarding different carrier frequency offsets, different channel frequency
responses, different preamble patterns in different bands. Utilizing a
half-cycle Constant Amplitude Zero Auto Correlation (CAZAC) sequence as the preamble sequence, the estimator with a semi-cross
contrast scheme between two successive OFDM symbols is proposed. The CRLB and complexity of the proposed algorithm are derived.
Compared to the reference estimators, the proposed method achieves
significantly less complexity (about 50%) for all preamble patterns of the MB-OFDM systems. The CRLBs turn out to be of well performance.
Abstract: We have proposed an information filtering system
using index word selection from a document set based on the
topics included in a set of documents. This method narrows
down the particularly characteristic words in a document set
and the topics are obtained by Sparse Non-negative Matrix
Factorization. In information filtering, a document is often
represented with the vector in which the elements correspond
to the weight of the index words, and the dimension of the
vector becomes larger as the number of documents is
increased. Therefore, it is possible that useless words as index
words for the information filtering are included. In order to
address the problem, the dimension needs to be reduced. Our
proposal reduces the dimension by selecting index words
based on the topics included in a document set. We have
applied the Sparse Non-negative Matrix Factorization to the
document set to obtain these topics. The filtering is carried out
based on a centroid of the learning document set. The centroid
is regarded as the user-s interest. In addition, the centroid is
represented with a document vector whose elements consist of
the weight of the selected index words. Using the English test
collection MEDLINE, thus, we confirm the effectiveness of
our proposal. Hence, our proposed selection can confirm the
improvement of the recommendation accuracy from the other
previous methods when selecting the appropriate number of
index words. In addition, we discussed the selected index
words by our proposal and we found our proposal was able to
select the index words covered some minor topics included in
the document set.
Abstract: This paper presents a 2-D hydrodynamic model of the ablated plasma when irradiating a 50 μm Al solid target with a single pulsed ion beam. The Lagrange method is used to solve the moving fluid for the ablated plasma production and formation mechanism. In the calculations, a 10-ns-single-pulsed of ion beam with a total energy density of 120 J/cm2, is used. The results show that the ablated plasma was formed after 2 ns of ion beam irradiation and it started to expand right after 4-6 ns. In addition, the 2-D model give a better understanding of pulsed ion beam-solid target ablated plasma production and expansion process clearer.
Abstract: In this paper, we describe a rule-based message passing method to support developing collaborative applications, in which multiple users share resources in distributed environments. Message communications of applications in collaborative environments tend to be very complex because of the necessity to manage context situations such as sharing events, access controlling of users, and network places. In this paper, we propose a message communications method based on unification of artificial intelligence and logic programming for defining rules of such context information in a procedural object-oriented programming language. We also present an implementation of the method as java classes.
Abstract: Text similarity measurement is a fundamental issue in
many textual applications such as document clustering, classification,
summarization and question answering. However, prevailing approaches
based on Vector Space Model (VSM) more or less suffer
from the limitation of Bag of Words (BOW), which ignores the semantic
relationship among words. Enriching document representation
with background knowledge from Wikipedia is proven to be an effective
way to solve this problem, but most existing methods still
cannot avoid similar flaws of BOW in a new vector space. In this
paper, we propose a novel text similarity measurement which goes
beyond VSM and can find semantic affinity between documents.
Specifically, it is a unified graph model that exploits Wikipedia as
background knowledge and synthesizes both document representation
and similarity computation. The experimental results on two different
datasets show that our approach significantly improves VSM-based
methods in both text clustering and classification.
Abstract: Customer-supplier collaboration enables firms to
achieve greater success than acting independently. Nevertheless, not
many firms have fully utilized the potential of collaboration. This
paper presents organizational and human related success factors for
collaboration in manufacturing supply chains in casting industry. Our
research approach was a case study including multiple cases. Data
was gathered by interviews and group discussions in two different
research projects. In the first research project we studied seven firms
and in the second five. It was found that the success factors are
interrelated, in other words, organizational and human factors
together enable success but not any of them alone. Some of the found
success factors are a culture of following agreements, and a speed of
informing the partner about changes affecting to the product or the
delivery chain.
Abstract: A solar powered air heating system using one ended evacuated tubes is experimentally investigated. A solar air heater containing forty evacuated tubes is used for heating purpose. The collector surface area is about 4.44 m2. The length and outer diameters of the outer glass tube and absorber tube are 1500, 47 and 37 mm, respectively. In this experimental setup, we have a header (heat exchanger) of square shape (190 mm x 190 mm). The length of header is 1500 mm. The header consists of a hollow pipe in the center whose diameter is 60 mm through which the air is made to flow. The experimental setup contains approximately 108 liters of water. Water is working as heat collecting medium which collects the solar heat falling on the tubes. This heat is delivered to the air flowing through the header pipe. This heat flow is due to natural convection and conduction. The outlet air temperature depends upon several factors along with air flow rate and solar radiation intensity. The study has been done for both up-flow and down-flow of air in header in similar weather conditions, at different flow rates. In the present investigations the study has been made to find the effect of intensity of solar radiations and flow rate of air on the out let temperature of the air with time and which flow is more efficient. The obtained results show that the system is highly effective for the heating in this region. Moreover, it has been observed that system is highly efficient for the particular flow rate of air. It was also observed that downflow configuration is more effective than up-flow condition at all flow rates due to lesser losses in down-flow. The results show that temperature differences of upper head and lower head, both of water and surface of pipes on the respective ends is lower in down-flow.
Abstract: The effect of autofrettage process in strain hardened
thick-walled pressure vessels has been investigated theoretically by
finite element modeling. Equivalent von Mises stress is used as yield
criterion to evaluate the optimum autofrettage pressure and the
optimum radius of elastic-plastic junction. It has been observed that
the optimum autofrettage pressure increases along with the working
pressure. For two different working pressures, the effect of the ratio
of outer to inner radius (b/a=k) value on the optimum autofrettage
pressure is also noticed. The Optimum autofrettage pressure solely
depends on K value rather than on the inner or outer radius.
Furthermore, percentage reduction of von Mises stresses is compared
for different working pressures and different k values. Maximum von
Mises stress developed at different autofrettage pressure is equated
for elastic perfectly plastic and elastic-plastic material with different
slope of strain hardening segment. Cylinder material having higher
slope of strain hardening segment provides better benedictions in the
autofrettage process.
Abstract: Nowadays, the importance of energy saving is clearance to everyone. By attention to increasing price of fuels and also the problems of environment pollutions, there are the most efforts for using fuels littler and more optimum in everywhere. This essay studies optimizing of gas consumption in gas-burner space heaters. In oven of each gas-burner space heaters there is two snags to prevent the hot air (the result of combustion of natural gas) to go out of oven of the gas-burner space heaters directly without delivering its heat to the space of favorite environment like a room. These snags cause a excess circulating that helps hot air deliver its heat to the space of favorite environment. It means the exhaust air temperature will be decreased then when there are no snags. This is the aim of this essay to use maximum potential energy of the natural gas to make heat. In this study, by the help of a finite volume software (FLUENT) consumption of the gas-burner space heaters is simulated and optimized. At the end of this writing, by comparing the results of software and experimental results, it will be proved the authenticity of this method.
Abstract: Breast cancer is one of the most frequent occurring cancers in women throughout the world including U.K. The grading of this cancer plays a vital role in the prognosis of the disease. In this paper we present an overview of the use of advanced computational method of fuzzy inference system as a tool for the automation of breast cancer grading. A new spectral data set obtained from Fourier Transform Infrared Spectroscopy (FTIR) of cancer patients has been used for this study. The future work outlines the potential areas of fuzzy systems that can be used for the automation of breast cancer grading.
Abstract: Using strength Pulse Electrical Field (PEF) in food
industries is a non-thermal process that can deactivate
microorganisms and increase penetration in plant and animals tissues
without serious impact on food taste and quality. In this paper designing and fabricating of a PEF generator has been presented. Pulse generation methods have been surveyed and the best of them
selected. The equipment by controller set can generate square pulse with adjustable parameters such as amplitude 1-5kV, frequency 0.1-10Hz, pulse width 10-100s, and duty cycle 0-100%. Setting the number of pulses, and presenting the output voltage and current
waveforms on the oscilloscope screen are another advantages of this
equipment. Finally, some food samples were tested that yielded the satisfactory results. PEF applying had considerable effects on potato, banana and purple cabbage. It caused increase Brix factor from 0.05
to 0.15 in potato solution. It is also so effective in extraction color material from purple cabbage. In the last experiment effects of PEF
voltages on color extraction of saffron scum were surveyed (about 6% increasing yield).
Abstract: The construction of original functional sample of the portable device for fast analysis of energetic materials has been described in the paper. The portable device consisting of two parts – an original miniaturized microcolumn liquid chromatograph and a unique chemiluminescence detector – has been proposed and realized. In a very short time, this portable device is capable of identifying selectively most of military nitramine- and nitroesterbased explosives as well as inorganic nitrates occurring in trace concentrations in water or in soil. The total time required for the identification of extracts is shorter than 8 minutes.
Abstract: For improving the efficiency of human 3D tracking, we
present an algorithm to track 3D Arm Motion. First, the Hierarchy
Limb Model (HLM) is proposed based on the human 3D skeleton
model. Second, via graph decomposition, the arm motion state space,
modeled by HLM, can be discomposed into two low dimension
subspaces: root nodes and leaf nodes. Finally, Rao-Blackwellised
Particle Filter is used to estimate the 3D arm motion. The result of
experiment shows that our algorithm can advance the computation
efficiency.
Abstract: The study investigated the educational implications
that can be derived from the work of a variety of celebrated figures
such as Piaget, Vygotsky, and Bruner that will be helpful in the field
of language learning. However, the writer believed these views were
previously expressed not full–fledged by Comenius who has been
described by Howatt (1984) as a genius–the one that the history of
language teaching can claim. And we owe to him more than anyone.
Abstract: This paper examines economic and Information and Communication Technology (ICT) development influence on recently increasing Internet purchases by individuals for European Union member states. After a growing trend for Internet purchases in EU27 was noticed, all possible regression analysis was applied using nine independent variables in 2011. Finally, two linear regression models were studied in detail. Conducted simple linear regression analysis confirmed the research hypothesis that the Internet purchases in analyzed EU countries is positively correlated with statistically significant variable Gross Domestic Product per capita (GDPpc). Also, analyzed multiple linear regression model with four regressors, showing ICT development level, indicates that ICT development is crucial for explaining the Internet purchases by individuals, confirming the research hypothesis.
Abstract: Service life of existing reinforced concrete (RC)
structures in coastal towns of Sabah has been affected very much.
Concrete crack, spalling of concrete cover and reinforcement rusting
of RC buildings are seen even within 5 years of construction in
Sabah. Hence, in this study a new mix design of concrete grout was
developed using locally available materials and investigated under
two curing conditions and workability, compressive strength,
Accelerated Mortar Bar Test (AMBT), water absorption, volume of
permeable voids (VPV), Sorptivity and 90-days salt ponding test
were conducted. The compressive strength of concrete grout at the
age 90 days was found to be 44.49 N/mm2 under water curing. It was
observed that the percentage of mortar bar length change was below
1% for developed concrete grout. The water absorption of the
concrete grout was in between the range of 0.88 % to 3.60 % under
two different curing up to the age 90 days. It was also observed that
the VPV of concrete was in the range of 0 % to 9.75 and 2.44% to
13.05% under water curing and site curing respectively. It was found
that the Sorptivity of the concrete grout under water curing at the age
of 28 days is 0.211mm/√min and at the age 90 day are 0.067
mm/√min. The chloride content decreased greatly, 90% after a depth
of 15 mm. It was noticed that the site cured samples showed higher
chloride contents near surface compared to water cured samples.
This investigation suggested that the developed mix design of
concrete grout using locally available construction materials can be
used for crack repairing of existing RC structures in Sabah.
Abstract: The complex shape of the human pelvic bone was
successfully imaged and modeled using finite element FE processing.
The bone was subjected to quasi-static and dynamic loading
conditions simulating the effect of both weight gain and impact.
Loads varying between 500 – 2500 N (~50 – 250 Kg of weight) was
used to simulate 3D quasi-static weight gain. Two different 3D
dynamic analyses, body free fall at two different heights (1 and 2 m)
and forced side impact at two different velocities (20 and 40 Km/hr)
were also studied. The computed resulted stresses were compared for
the four loading cases, where Von Misses stresses increases linearly
with the weight gain increase under quasi-static loading. For the
dynamic models, the Von Misses stress history behaviors were
studied for the affected area and effected load with respect to time.
The normalization Von Misses stresses with respect to the applied
load were used for comparing the free fall and the forced impact load
results. It was found that under the forced impact loading condition
an over lapping behavior was noticed, where as for the free fall the
normalized Von Misses stresses behavior was found to nonlinearly
different. This phenomenon was explained through the energy
dissipation concept. This study will help designers in different
specialization in defining the weakest spots for designing different
supporting systems.
Abstract: Sixteen selected deep-sea fish obtained from Southern
Java Ocean and Western Sumatra Ocean was analyzed to determine
its proximate, fatty acid and mineral composition. The moisture
content was ranged from 64.38 to 86.04 %, ash from 0.17 to 0.69 %,
the fat content was 1.54 – 13.30 % while the protein content varied
from 15.84 to 23.60%. Among the fatty acids, oleic acid and palmitic
acid was the dominant MUFA and SFA. Linoleic acid was the
highest PUFA found at the selected deep-sea fish. Phospor was the
highest macroelement concentration on selected deep-sea fish,
followed by K, Ca, Mg and Iod, Fe and Zn among microelement. The
trace concentration was found at Se microelement.