Abstract: Simultaneous transient conduction and radiation heat
transfer with heat generation is investigated. Analysis is carried out
for both steady and unsteady situations. two-dimensional gray
cylindrical enclosure with an absorbing, emitting, and isotropically
scattering medium is considered. Enclosure boundaries are assumed
at specified temperatures. The heat generation rate is considered
uniform and constant throughout the medium. The lattice Boltzmann
method (LBM) was used to solve the energy equation of a transient
conduction-radiation heat transfer problem. The control volume finite
element method (CVFEM) was used to compute the radiative
information. To study the compatibility of the LBM for the energy
equation and the CVFEM for the radiative transfer equation, transient
conduction and radiation heat transfer problems in 2-D cylindrical
geometries were considered. In order to establish the suitability of the
LBM, the energy equation of the present problem was also solved
using the the finite difference method (FDM) of the computational
fluid dynamics. The CVFEM used in the radiative heat transfer was
employed to compute the radiative information required for the
solution of the energy equation using the LBM or the FDM (of the
CFD). To study the compatibility and suitability of the LBM for the
solution of energy equation and the CVFEM for the radiative
information, results were analyzed for the effects of various
parameters such as the boundary emissivity. The results of the LBMCVFEM
combination were found to be in excellent agreement with
the FDM-CVFEM combination. The number of iterations and the
steady state temperature in both of the combinations were found
comparable. Results are found for situations with and without heat
generation. Heat generation is found to have significant bearing on
temperature distribution.
Abstract: We present a simplified equalization technique for a
π/4 differential quadrature phase shift keying ( π/4 -DQPSK) modulated
signal in a multipath fading environment. The proposed equalizer is
realized as a fractionally spaced adaptive decision feedback equalizer
(FS-ADFE), employing exponential step-size least mean square
(LMS) algorithm as the adaptation technique. The main advantage of
the scheme stems from the usage of exponential step-size LMS algorithm
in the equalizer, which achieves similar convergence behavior
as that of a recursive least squares (RLS) algorithm with significantly
reduced computational complexity. To investigate the finite-precision
performance of the proposed equalizer along with the π/4 -DQPSK
modem, the entire system is evaluated on a 16-bit fixed point digital
signal processor (DSP) environment. The proposed scheme is found
to be attractive even for those cases where equalization is to be
performed within a restricted number of training samples.
Abstract: With the enormous growth on the web, users get easily
lost in the rich hyper structure. Thus developing user friendly and
automated tools for providing relevant information without any
redundant links to the users to cater to their needs is the primary task
for the website owners. Most of the existing web mining algorithms
have concentrated on finding frequent patterns while neglecting the
less frequent one that are likely to contain the outlying data such as
noise, irrelevant and redundant data. This paper proposes new
algorithm for mining the web content by detecting the redundant
links from the web documents using set theoretical(classical
mathematics) such as subset, union, intersection etc,. Then the
redundant links is removed from the original web content to get the
required information by the user..
Abstract: The weight constrained shortest path problem
(WCSPP) is one of most several known basic problems in
combinatorial optimization. Because of its importance in many areas
of applications such as computer science, engineering and operations
research, many researchers have extensively studied the WCSPP.
This paper mainly concentrates on the reduction of total search space
for finding WCSP using some existing Genetic Algorithm (GA). For
this purpose, some controlled schemes of genetic operators are
adopted on list chromosome representation. This approach gives a
near optimum solution with smaller elapsed generation than classical
GA technique. From further analysis on the matter, a new
generalized schema theorem is also developed from the philosophy
of Holland-s theorem.
Abstract: In this paper, we propose a reversible watermarking
scheme based on histogram shifting (HS) to embed watermark bits
into the H.264/AVC standard videos by modifying the last nonzero
level in the context adaptive variable length coding (CAVLC) domain.
The proposed method collects all of the last nonzero coefficients (or
called last level coefficient) of 4×4 sub-macro blocks in a macro
block and utilizes predictions for the current last level from the
neighbor block-s last levels to embed watermark bits. The feature of
the proposed method is low computational and has the ability of
reversible recovery. The experimental results have demonstrated that
our proposed scheme has acceptable degradation on video quality and
output bit-rate for most test videos.
Abstract: Classification of video sequences based on their contents is a vital process for adaptation techniques. It helps decide which adaptation technique best fits the resource reduction requested by the client. In this paper we used the principal feature analysis algorithm to select a reduced subset of video features. The main idea is to select only one feature from each class based on the similarities between the features within that class. Our results showed that using this feature reduction technique the source video features can be completely omitted from future classification of video sequences.
Abstract: Tofurther advance research on immune-related genes
from T. molitor, we constructed acDNA library and analyzed
expressed sequence taq (EST) sequences from 1,056 clones. After
removing vector sequence and quality checkingthrough thePhred
program (trim_alt 0.05 (P-score>20), 1039 sequences were generated.
The average length of insert was 792 bp. In addition, we identified 162
clusters, 167 contigs and 391 contigs after clustering and assembling
process using a TGICL package. EST sequences were searchedagainst
NCBI nr database by local BLAST (blastx, E
Abstract: The use of machine vision to inspect the outcome of
surgical tasks is investigated, with the aim of incorporating this
approach in robotic surgery systems. Machine vision is a non-contact
form of inspection i.e. no part of the vision system is in direct contact
with the patient, and is therefore well suited for surgery where
sterility is an important consideration,. As a proof-of-concept, three
primary surgical tasks for a common neurosurgical procedure were
inspected using machine vision. Experiments were performed on
cadaveric pig heads to simulate the two possible outcomes i.e.
satisfactory or unsatisfactory, for tasks involved in making a burr
hole, namely incision, retraction, and drilling. We identify low level
image features to distinguish the two outcomes, as well as report on
results that validate our proposed approach. The potential of using
machine vision in a surgical environment, and the challenges that
must be addressed, are identified and discussed.
Abstract: This paper outlines the development of a learning retrieval agent. Task of this agent is to extract knowledge of the Active Semantic Network in respect to user-requests. Based on a reinforcement learning approach, the agent learns to interpret the user-s intention. Especially, the learning algorithm focuses on the retrieval of complex long distant relations. Increasing its learnt knowledge with every request-result-evaluation sequence, the agent enhances his capability in finding the intended information.
Abstract: This work presents the results of a study carried out to
determine the sliding wear behavior and its effect on the process
parameters of components manufactured by direct metal laser
sintering (DMLS). A standard procedure and specimen had been used
in the present study to find the wear behavior. Using Taguchi-s
experimental technique, an orthogonal array of modified L8 had been
developed. Sliding wear testing using pin-on-disk machine was
carried out and analysis of variance (ANOVA) technique was used to
investigate the effect of process parameters and to identify the main
process parameter that influences the properties of wear behavior on
the DMLS components. It has been found that part orientation, one
of the selected process parameter had more influence on wear as
compared to other selected process parameters.
Abstract: This work presents the highly accurate numerical calculation
of the natural frequencies for functionally graded beams with
simply supported boundary conditions. The Timoshenko first order
shear deformation beam theory and the higher order shear deformation
beam theory of Reddy have been applied to the functionally
graded beams analysis. The material property gradient is assumed
to be in the thickness direction. The Hamilton-s principle is utilized
to obtain the dynamic equations of functionally graded beams. The
influences of the volume fraction index and thickness-to-length ratio
on the fundamental frequencies are discussed. Comparison of the
numerical results for the homogeneous beam with Euler-Bernoulli
beam theory results show that the derived model is satisfactory.
Abstract: In this paper, investigation of subsynchronous
resonance (SSR) characteristics of a hybrid series compensated
system and the design of voltage controller for three level 24-pulse
Voltage Source Converter based Static Synchronous Series
Compensator (SSSC) is presented. Hybrid compensation consists of
series fixed capacitor and SSSC which is a active series FACTS
controller. The design of voltage controller for SSSC is based on
damping torque analysis, and Genetic Algorithm (GA) is adopted for
tuning the controller parameters. The SSR Characteristics of SSSC
with constant reactive voltage control modes has been investigated.
The results show that the constant reactive voltage control of SSSC
has the effect of reducing the electrical resonance frequency, which
detunes the SSR.The analysis of SSR with SSSC is carried out based
on frequency domain method, eigenvalue analysis and transient
simulation. While the eigenvalue and damping torque analysis are
based on D-Q model of SSSC, the transient simulation considers both
D-Q and detailed three phase nonlinear system model using
switching functions.
Abstract: Convergence of power series solutions for a class of
non-linear Abel type equations, including an equation that arises
in nonlinear cooling of semi-infinite rods, is very slow inside their
small radius of convergence. Beyond that the corresponding power
series are wildly divergent. Implementation of nonlinear sequence
transformation allow effortless evaluation of these power series on
very large intervals..
Abstract: In this paper presented initial design of Low Speed
Axial Flux Permanent Magnet (AFPM) Machine with Non-Slotted
TORUS topology type by use of certain algorithm (Appendix).
Validation of design algorithm studied by means of selected data of
an initial prototype machine. Analytically design calculation carried
out by means of design algorithm and obtained results compared with
results of Finite Element Method (FEM).
Abstract: Soccer simulation is an effort to motivate researchers and practitioners to do artificial and robotic intelligence research; and at the same time put into practice and test the results. Many researchers and practitioners throughout the world are continuously working to polish their ideas and improve their implemented systems. At the same time, new groups are forming and they bring bright new thoughts to the field. The research includes designing and executing robotic soccer simulation algorithms. In our research, a soccer simulation player is considered to be an intelligent agent that is capable of receiving information from the environment, analyze it and to choose the best action from a set of possible ones, for its next move. We concentrate on developing a two-phase method for the soccer player agent to choose its best next move. The method is then implemented into our software system called Nexus simulation team of Ferdowsi University. This system is based on TsinghuAeolus[1] team that was the champion of the world RoboCup soccer simulation contest in 2001 and 2002.
Abstract: One of the main concerns in the Information Technology field is adoption with new technologies in organizations which may result in increasing the usage paste of these technologies.This study aims to look at the issue of culture-s role in accepting and using new technologies in organizations. The study examines the effect of culture on accepting and intention to use new technology in organizations. Studies show culture is one of the most important barriers in adoption new technologies. The model used for accepting and using new technology is Technology Acceptance Model (TAM), while for culture and dimensions a well-known theory by Hofsted was used. Results of the study show significant effect of culture on intention to use new technologies. All four dimensions of culture were tested to find the strength of relationship with behavioral intention to use new technologies. Findings indicate the important role of culture in the level of intention to use new technologies and different role of each dimension to improve adaptation process. The study suggests that transferring of new technologies efforts are most likely to be successful if the parties are culturally aligned.
Abstract: An ethnobotanical study was conducted to document
local knowledge and potentials of wild edible tubers that has been
reported and sighted and to investigate and record their distribution in
Pulau Redang and nearby islands of Terengganu, Malaysia.
Information was gathered from 42 villagers by using semi-structured
questionnaire. These respondents were selected randomly and no
appointment was made prior to the visits. For distribution, the
locations of wild edible tubers were recorded by using the Global
Positioning System (GPS). The wild edible tubers recorded were ubi
gadung, ubi toyo, ubi kasu, ubi jaga, ubi seratus and ubi kertas.
Dioscorea or commonly known as yam is reported to be one of the
major food sources worldwide. The majority of villagers used
Dioscorea hispida Dennst. or ubi gadung in many ways in their life
such as for food, medicinal purposes and fish poison. The villagers
have identified this ubi gadung by looking at the morphological
characteristics; that include leaf shape, stem and the color of the
tuber-s flesh.
Abstract: Business process management (BPM) has become
widely accepted within business community as a means for
improving business performance. However, it is of the highest
importance to incorporate BPM as part of the curriculum at the
university level education in order to achieve the appropriate
acceptance of the method. Goal of the paper is to determine the
current state of education in business process management (BPM) at
the Croatian universities and abroad. It investigates the applied forms
of instruction and teaching methods and gives several proposals for
BPM courses improvement. Since majority of undergraduate and
postgraduate students have limited understanding of business
processes and lack of any practical experience, there is a need for
introducing new teaching approaches. Therefore, we offer some
suggestions for further improvement, among which the introduction
of simulation games environment in BPM education is strongly
recommended.
Abstract: Toughening of polyamide 6 (PA6)/ Nanoclay (NC) nanocomposites with styrene-ethylene/butadiene-styrene copolymer (SEBS) using maleated styrene-ethylene/butadiene-styrene copolymer (mSEBS)/ as a compatibilizer were investigated by blending them in a co-rotating twin-screw extruder. Response surface method of experimental design was used for optimizing the material and processing parameters. Effect of four factors, including SEBS, mSEBS and NC contents as material variables and order of mixing as a processing factor, on toughness of hybrid nanocomposites were studied. All the prepared samples showed ductile behavior and low temperature Izod impact toughness of some of the hybrid nanocomposites demonstrated 900% improvement compared to the PA6 matrix while the modulus showed maximum enhancement of 20% compared to the pristine PA6 resin.
Abstract: Advent enhancements in the field of computing have
increased massive use of web based electronic documents. Current
Copyright protection laws are inadequate to prove the ownership for
electronic documents and do not provide strong features against
copying and manipulating information from the web. This has
opened many channels for securing information and significant
evolutions have been made in the area of information security.
Digital Watermarking has developed into a very dynamic area of
research and has addressed challenging issues for digital content.
Watermarking can be visible (logos or signatures) and invisible
(encoding and decoding). Many visible watermarking techniques
have been studied for text documents but there are very few for web
based text. XML files are used to trade information on the internet
and contain important information. In this paper, two invisible
watermarking techniques using Synonyms and Acronyms are
proposed for XML files to prove the intellectual ownership and to
achieve the security. Analysis is made for different attacks and
amount of capacity to be embedded in the XML file is also noticed.
A comparative analysis for capacity is also made for both methods.
The system has been implemented using C# language and all tests are
made practically to get the results.