Abstract: With the increasing number of on-chip components and the critical requirement for processing power, Chip Multiprocessor (CMP) has gained wide acceptance in both academia and industry during the last decade. However, the conventional bus-based onchip communication schemes suffer from very high communication delay and low scalability in large scale systems. Network-on-Chip (NoC) has been proposed to solve the bottleneck of parallel onchip communications by applying different network topologies which separate the communication phase from the computation phase. Observing that the memory bandwidth of the communication between on-chip components and off-chip memory has become a critical problem even in NoC based systems, in this paper, we propose a novel 3D NoC with on-chip Dynamic Random Access Memory (DRAM) in which different layers are dedicated to different functionalities such as processors, cache or memory. Results show that, by using our proposed architecture, average link utilization has reduced by 10.25% for SPLASH-2 workloads. Our proposed design costs 1.12% less execution cycles than the traditional design on average.
Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.
Abstract: Water recycling represents an important challenge for many countries, in particular in countries where this natural resource is rare. On the other hand, in many operations, water is used as a cooling medium, as a high proportion of water consumed in industry is used for cooling purposes. Generally this water is rejected directly to the nature. This reject will cause serious environment damages as well as an important waste of this precious element.. On way to solve these problems is to reuse and recycle this warm water, through the use of natural cooling medium, such as air in a heat exchanger unit, known as a cooling tower. A poor performance, design or reliability of cooling towers will result in lower flow rate of cooling water an increase in the evaporation of water, an hence losses of water and energy. This paper which presents an experimental investigate of thermal and hydraulic performances of a mechanical cooling tower, enables to show that the water evaporation rate, Mev, increases with an increase in the air and water flow rates, as well as inlet water temperature and for fixed air flow rates, the pressure drop (ΔPw/Z) increases with increasing , L, due to the hydrodynamic behavior of the air/water flow.
Abstract: Optical burst switching (OBS) has been proposed to
realize the next generation Internet based on the wavelength division
multiplexing (WDM) network technologies. In the OBS, the burst
contention is one of the major problems. The deflection routing has
been designed for resolving the problem. However, the deflection
routing becomes difficult to prevent from the burst contentions as the
network load becomes high. In this paper, we introduce a flow rate
control methods to reduce burst contentions. We propose new flow
rate control methods based on the leaky bucket algorithm and
deflection routing, i.e. separate leaky bucket deflection method, and
dynamic leaky bucket deflection method. In proposed methods, edge
nodes which generate data bursts carry out the flow rate control
protocols. In order to verify the effectiveness of the flow rate control in
OBS networks, we show that the proposed methods improve the
network utilization and reduce the burst loss probability through
computer simulations.
Abstract: In this paper we propose a novel RF LDMOS structure which employs a thin strained silicon layer at the top of the channel and the N-Drift region. The strain is induced by a relaxed Si0.8 Ge0.2 layer which is on top of a compositionally graded SiGe buffer. We explain the underlying physics of the device and compare the proposed device with a conventional LDMOS in terms of energy band diagram and carrier concentration. Numerical simulations of the proposed strained silicon laterally diffused MOS using a 2 dimensional device simulator indicate improvements in saturation and linear transconductance, current drivability, cut off frequency and on resistance. These improvements are however accompanied with a suppression in the break down voltage.
Abstract: A study was undertaken to investigate the effect of
liquid nitrogen aeration on mortalities of adult Cryptolestes
furrugineus, rusty grain beetles, in a prototype cardboard grain bin
equipped with an aeration system. The grain bin was filled with Hard
Red Spring wheat and liquid nitrogen was introduced from the bottom
of the bin. The survival of both cold acclimated and unacclimated C.
furrugineus was tested. The study reveals that cold acclimated insects
had higher survival than unacclimated insects under similar cooling
conditions. In most cases, mortalities of as high as 100% were
achieved at the bottom 100 cm of the grain bin for unacclimated
insects for most of the trials. Insect survival increased as the distance
from the bottom of the grain bin increased. There was no adverse
effect of liquid nitrogen aeration on wheat germination.
Abstract: Aiming at the problems existing in low-carbon technology of Chinese manufacturing industries, such as irrational energy structure, lack of technological innovation, financial constraints, this paper puts forward the suggestion that the leading role of the government is combined with the roles of enterprises and market. That is, through increasing the governmental funding the adjustment of the industrial structures and enhancement of the legal supervision are supported. Technological innovation is accelerated by the enterprises, and the carbon trading will be promoted so as to trigger the low-carbon revolution in Chinese manufacturing field.
Abstract: The objectives of this research are to search the
management pattern of Bang Khonthi lodging entrepreneurs for
sufficient economy ways, to know the threat that affects this sector
and design fit arrangement model to sustain their business with
Samut Songkram style. What will happen if they do not use this
approach? Will they have a financial crisis? The data and information
are collected by informal discussions with 8 managers and 400
questionnaires. A mixed methods of both qualitative research and
quantitative research are used. Bent Flyvbjerg-s phronesis is utilized
for this analysis. Our research will prove that sufficient economy can
help small business firms to solve their problems. We think that the
results of our research will be a financial model to solve many
problems of the entrepreneurs and this way will can be a model for
other provinces of Thailand.
Abstract: The use of additions in cement in manufacturing,
mortar and concrete offers economic and ecological advantages. Cements with additions such as limestone, slag and natural
pouzzolana are produced in cement factories in Algeria. Several studies analyzed the effect of these additions on the physical and
mechanical properties as well as the durability of concrete. However,
few studies were conducted on the effect of local metakaolin on
mechanical properties and durability of concrete. The main purpose
of this paper is to analyze the performance of mortar and concrete with local metakaolin. The preparation of the metakaolin was carried
out by calcination of kaolin at a temperature of 850 °C for a period of 3 hours. The experimental results have shown that the rates of
substitutions of 10 and 15% metakaolin increases the compressive
strength and flexural strength at both early age and long term. The durability and the permeability were also improved by reducing the
coefficient of sorptivity.
Abstract: This paper presents a constrained valley detection
algorithm. The intent is to find valleys in the map for the path planning
that enables a robot or a vehicle to move safely. The constraint to the
valley is a desired width and a desired depth to ensure the space for
movement when a vehicle passes through the valley. We propose an
algorithm to find valleys satisfying these 2 dimensional constraints.
The merit of our algorithm is that the pre-processing and the
post-processing are not necessary to eliminate undesired small valleys.
The algorithm is validated through simulation using digitized
elevation data.
Abstract: This paper presents a portable robot that is to use for
welding process in shipbuilding yard. It has six degree of freedom and
3kg payload capability. Its weight is 21.5kg so that human workers can
carry it to the work place. Its body mainly made of magnesium alloy
and aluminum alloy for few parts that require high strength. Since the
distance between robot and controller should be 50m at most, the robot
controller controls the robot through EtherCAT. RTX and KPA are
used for real time EtherCAT control on Windows XP. The
performance of the developed robot was satisfactory, in welding of U
type cell in shipbuilding yard.
Abstract: The analysis of electromagnetic environment using
deterministic mathematical models is characterized by the
impossibility of analyzing a large number of interacting network
stations with a priori unknown parameters, and this is characteristic,
for example, of mobile wireless communication networks. One of the
tasks of the tools used in designing, planning and optimization of
mobile wireless network is to carry out simulation of electromagnetic
environment based on mathematical modelling methods, including
computer experiment, and to estimate its effect on radio
communication devices. This paper proposes the development of a
statistical model of electromagnetic environment of a mobile
wireless communication network by describing the parameters and
factors affecting it including the propagation channel and their
statistical models.
Abstract: Buildings are considered as significant part in the
cities, which plays main role in organization and arrangement of city
appearance, which is affects image of that building facades, as an
connective between inner and outer space, have a main role in city
image and they are classified as rich image and poor image by people
evaluation which related to visual architectural and urban elements in
building facades. the buildings in Karimi street , in Lahijan city
where, lies in north of Iran, contain the variety of building's facade
types which, have made a city image in Historical part of Lahijan
city, while reflected the Iranian cities identity. The study attempt to
identify the architectural and urban elements that impression the
image of building facades in historical area, based on public
evaluation. Quantitative method were used and the data was collected
through questionnaire survey, the result presented architectural style,
color, shape, and design evaluated by people as most important factor
which should be understate in future development. in fact, the rich
architectural style with strong design make strong city image as weak
design make poor city image.
Abstract: The study applied a combination of organisational learning models (Senge, 1994: Pedler, Burgoyne and Boydell, 1991) and later adopted fifteen organisational learning principles with one of the biggest energy providers in South East Asia. The purposes of the current study were to: a) investigate the company-s practices on fifteen organisational learning principles; b) explore the perceptions and expectations of its employees in relations to the principles; and c) compare the perceptions and expectations between management and non-management staff toward the fifteen factors. One hundred and ten employees responded on a designed questionnaire and the results indicated that the company was practicing activities that associated with organisational learning principles. Also, according to the T-test results, significant differences between management and non-management respondents were found. Research implications are also provided.
Abstract: in dissimilar material joints, failure often occurs
along the interface between two materials due to stress singularity.
Stress distribution and its concentration depend on materials and
geometry of the junction. Inhomogenity of stress distribution at the
interface of junction of two materials with different elastic modules
and stress concentration in this zone are the main factors resulting in
rupture of the junction. Effect of joining angle in the interface of
aluminum-polycarbonate will be discussed in this paper. Computer
simulation and finite element analysis by ABAQUS showed that
convex interfacial joint leads to stress reduction at junction corners in
compare with straight joint. This finding is confirmed by photoelastic
experimental results.
Abstract: This paper proposes a scheduling scheme using feedback
control to reduce the response time of aperiodic tasks with soft
real-time constraints. We design an algorithm based on the proposed
scheduling scheme and Total Bandwidth Server (TBS) that is a
conventional server technique for scheduling aperiodic tasks. We then
describe the feedback controller of the algorithm and give the control
parameter tuning methods. The simulation study demonstrates that the
algorithm can reduce the mean response time up to 26% compared
to TBS in exchange for slight deadline misses.
Abstract: Human computer interaction has progressed
considerably from the traditional modes of interaction. Vision based
interfaces are a revolutionary technology, allowing interaction
through human actions, gestures. Researchers have developed
numerous accurate techniques, however, with an exception to few
these techniques are not evaluated using standard HCI techniques. In
this paper we present a comprehensive framework to address this
issue. Our evaluation of a computer vision application shows that in
addition to the accuracy, it is vital to address human factors
Abstract: Road Traffic Accidents are a major cause of disability and death throughout the world. The control of intelligent vehicles in order to reduce human error and boost ease congestion is not accomplished solely by the aid of human resources. The present article is an attempt to introduce an intelligent control system based on RFID technology. By the help of RFID technology, vehicles are connected to computerized systems, intelligent light poles and other available hardware along the way. In this project, intelligent control system is capable of tracking all vehicles, crisis management and control, traffic guidance and recording Driving offences along the highway.
Abstract: Capacitive electrocardiogram (ECG) measurement is an attractive approach for long-term health monitoring. However, there is little literature available on its implementation, especially for multichannel system in standard ECG leads. This paper begins from the design criteria for capacitive ECG measurement and presents a multichannel limb-lead capacitive ECG system with conductive fabric tapes pasted on a double layer PCB as the capacitive sensors. The proposed prototype system incorporates a capacitive driven-body (CDB) circuit to reduce the common-mode power-line interference (PLI). The presented prototype system has been verified to be stable by theoretic analysis and practical long-term experiments. The signal quality is competitive to that acquired by commercial ECG machines. The feasible size and distance of capacitive sensor have also been evaluated by a series of tests. From the test results, it is suggested to be greater than 60 cm2 in sensor size and be smaller than 1.5 mm in distance for capacitive ECG measurement.
Abstract: The three steps of the standard one-way nested grid
for a regional scale of the third generation WAve Model Cycle 4
(WAMC4) is scrutinized. The model application is enabled to solve
the energy balance equation on a coarse resolution grid in order to
produce boundary conditions for a smaller area by the nested grid
technique. In the present study, the model takes a full advantage of the
fine resolution of wind fields in space and time produced by the available
U.S. Navy Global Atmospheric Prediction System (NOGAPS)
model with 1 degree resolution. The nested grid application of the
model is developed in order to gradually increase the resolution from
the open ocean towards the South China Sea (SCS) and the Gulf of
Thailand (GoT) respectively. The model results were compared with
buoy observations at Ko Chang, Rayong and Huahin locations which
were obtained from the Seawatch project. In addition, the results were
also compared with Satun based weather station which was provided
from Department of Meteorology, Thailand. The data collected from
this station presented the significant wave height (Hs) reached 12.85
m. The results indicated that the tendency of the Hs from the model
in the spherical coordinate propagation with deep water condition in
the fine grid domain agreed well with the Hs from the observations.