Abstract: The dramatic increasing of sea-freight container
transportations and the developing trends for using containers in the
multimodal handling systems through the sea, rail, road and land in
nowadays market cause general managers of container terminals to
face challenges such as increasing demand, competitive situation,
new investments and expansion of new activities and need to use new
methods to fulfil effective operations both along quayside and within
the yard. Among these issues, minimizing the turnaround time of
vessels is considered to be the first aim of every container port
system. Regarding the complex structure of container ports, this
paper presents a simulation model that calculates the number of
trucks needed in the Iranian Shahid Rajaee Container Port for
handling containers between the berth and the yard. In this research,
some important criteria such as vessel turnaround time, gantry crane
utilization and truck utilization have been considered. By analyzing
the results of the model, it has been shown that increasing the number
of trucks to 66 units has a significant effect on the performance
indices of the port and can increase the capacity of loading and
unloading up to 10.8%.
Abstract: The Multi-Layered Perceptron (MLP) Neural
networks have been very successful in a number of signal processing
applications. In this work we have studied the possibilities and the
met difficulties in the application of the MLP neural networks for the
prediction of daily solar radiation data. We have used the Polack-Ribière algorithm for training the neural networks. A comparison, in
term of the statistical indicators, with a linear model most used in
literature, is also performed, and the obtained results show that the
neural networks are more efficient and gave the best results.
Abstract: Condition monitoring of electrical power equipment
has attracted considerable attention for many years. The aim of this
paper is to use Labview with Fuzzy Logic controller to build a
simulation system to diagnose transformer faults and monitor its
condition. The front panel of the system was designed using
LabVIEW to enable computer to act as customer-designed
instrument. The dissolved gas-in-oil analysis (DGA) method was
used as technique for oil type transformer diagnosis; meanwhile
terminal voltages and currents analysis method was used for dry type
transformer. Fuzzy Logic was used as expert system that assesses all
information keyed in at the front panel to diagnose and predict the
condition of the transformer. The outcome of the Fuzzy Logic
interpretation will be displayed at front panel of LabVIEW to show
the user the conditions of the transformer at any time.
Abstract: Permanent rivers are the main sources of renewable
water supply for the croplands under the irrigation and drainage
schemes. They are also the major source of sediment loads transport
into the storage reservoirs of the hydro-electrical dams, diversion
weirs and regulating dams. Sedimentation process results from soil
erosion which is related to poor watershed management and human
intervention ion in the hydraulic regime of the rivers. These could
change the hydraulic behavior and as such, leads to riverbed and river
bank scouring, the consequences of which would be sediment load
transport into the dams and therefore reducing the flow discharge in
water intakes. The present paper investigate sedimentation process
by varying the Manning coefficient "n" by using the SHARC
software along the watercourse in the Dez River. Results indicated
that the optimum "n" within that river range is 0.0315 at which
quantity minimum sediment loads are transported into the Eastern
intake. Comparison of the model results with those obtained by those
from the SSIIM software within the same river reach showed a very
close proximity between them. This suggests a relative accuracy with
which the model can simulate the hydraulic flow characteristics and
therefore its suitability as a powerful analytical tool for project
feasibility studies and project implementation.
Abstract: Breast motion and discomfort has been studied in
Australia, Britain and the United States, while little information was
known about the breast motion conditions of Chinese women. The aim
of this paper was to study the breast motion and discomfort of Chinese
women in no bra condition, daily bra condition and sports bra
condition. Breast motion and discomfort of 8 participants was assessed
during walking at 5km h-1 and running at 10km h-1. Statistical methods
were used to analyze the difference and relationship between breast
displacement, perceived breast motion and breast discomfort. Three
indexes were developed to evaluate the functions of bras on reducing
objective breast motion, subjective breast motion and breast
discomfort. The result showed that breast motion of Chinese women
was smaller than previous research, which may be resulted from
smaller breast size in Asian women.
Abstract: In current common research reports, salient regions
are usually defined as those regions that could present the main
meaningful or semantic contents. However, there are no uniform
saliency metrics that could describe the saliency of implicit image
regions. Most common metrics take those regions as salient regions,
which have many abrupt changes or some unpredictable
characteristics. But, this metric will fail to detect those salient useful
regions with flat textures. In fact, according to human semantic
perceptions, color and texture distinctions are the main characteristics
that could distinct different regions. Thus, we present a novel saliency
metric coupled with color and texture features, and its corresponding
salient region extraction methods. In order to evaluate the
corresponding saliency values of implicit regions in one image, three
main colors and multi-resolution Gabor features are respectively used
for color and texture features. For each region, its saliency value is
actually to evaluate the total sum of its Euclidean distances for other
regions in the color and texture spaces. A special synthesized image
and several practical images with main salient regions are used to
evaluate the performance of the proposed saliency metric and other
several common metrics, i.e., scale saliency, wavelet transform
modulus maxima point density, and important index based metrics.
Experiment results verified that the proposed saliency metric could
achieve more robust performance than those common saliency
metrics.
Abstract: The present paper presents a finite element model and
analysis for the interaction between a piezoresistive tactile sensor and
biological tissues. The tactile sensor is proposed for use in minimally
invasive surgery to deliver tactile information of biological tissues to
surgeons. The proposed sensor measures the relative hardness of soft
contact objects as well as the contact force. Silicone rubbers were
used as the phantom of biological tissues. Finite element analysis of
the silicone rubbers and the mechanical structure of the sensor were
performed using COMSOL Multiphysics (v3.4) environment. The
simulation results verify the capability of the sensor to be used to
differentiate between different kinds of silicone rubber materials.
Abstract: In this paper, creep constitutive equations of base
(Parent) and weld materials of the weldment for cold-drawn 304L
stainless steel have been obtained experimentally. For this purpose,
test samples have been generated from cold drawn bars and weld
material according to the ASTM standard. The creep behavior and
properties have been examined for these materials by conducting uniaxial
creep tests. Constant temperatures and constant load uni-axial
creep tests have been carried out at two high temperatures, 680 and
720 oC, subjected to constant loads, which produce initial stresses
ranging from 240 to 360 MPa. The experimental data have been used
to obtain the creep constitutive parameters using numerical
optimization techniques.
Abstract: Radio-frequency identification has entered as a beneficial means with conforming GS1 standards to provide the best solutions in the manufacturing area. It competes with other automated identification technologies e.g. barcodes and smart cards with regard to high speed scanning, reliability and accuracy as well. The purpose of this study is to improve production line-s performance by implementing RFID system in the manufacturing area on the basis of radio-frequency identification (RFID) system by 3D modeling in the program Cinema 4D R13 which provides obvious graphical scenes for users to portray their applications. Finally, with regard to improving system performance, it shows how RFID appears as a well-suited technology in a comparison of the barcode scanner to handle different kinds of raw materials in the production line base on logical process.
Abstract: Nowadays, the challenge in hydraulic turbine design is
the multi-objective design of turbine runner to reach higher
efficiency. The hydraulic performance of a turbine is strictly depends
on runner blades shape. The present paper focuses on the application
of the multi-objective optimization algorithm to the design of a small
Francis turbine runner. The optimization exercise focuses on the
efficiency improvement at the best efficiency operating point (BEP)
of the GAMM Francis turbine. A global optimization method based
on artificial neural networks (ANN) and genetic algorithms (GA)
coupled by 3D Navier-Stokes flow solver has been used to improve
the performance of an initial geometry of a Francis runner. The
results show the good ability of optimization algorithm and the final
geometry has better efficiency with initial geometry. The goal was to
optimize the geometry of the blades of GAMM turbine runner which
leads to maximum total efficiency by changing the design parameters
of camber line in at least 5 sections of a blade. The efficiency of the
optimized geometry is improved from 90.7% to 92.5%. Finally,
design parameters and the way of selection have been considered and
discussed.
Abstract: In this study we applied thermal lens (TL) technique
to study the effect of size on thermal diffusivity of cadmium sulphide
(CdS) nanofluid prepared by using γ-radiation method containing
particles with different sizes. In TL experimental set up a diode laser
of wavelength 514 nm and intensity stabilized He-Ne laser were used
as the excitation source and the probe beam respectively,
respectively. The experimental results showed that the thermal
diffusivity value of CdS nanofluid increases when the of particle size
increased.
Abstract: This paper employs a new approach to regulate the
blood glucose level of type I diabetic patient under an intensive
insulin treatment. The closed-loop control scheme incorporates
expert knowledge about treatment by using reinforcement learning
theory to maintain the normoglycemic average of 80 mg/dl and the
normal condition for free plasma insulin concentration in severe
initial state. The insulin delivery rate is obtained off-line by using Qlearning
algorithm, without requiring an explicit model of the
environment dynamics. The implementation of the insulin delivery
rate, therefore, requires simple function evaluation and minimal
online computations. Controller performance is assessed in terms of
its ability to reject the effect of meal disturbance and to overcome the
variability in the glucose-insulin dynamics from patient to patient.
Computer simulations are used to evaluate the effectiveness of the
proposed technique and to show its superiority in controlling
hyperglycemia over other existing algorithms
Abstract: In this paper stress and strain for two rotating thin
wall cylinder fitted together with initial interference and overlap are
computed. Also stress value for variation of initial interference is
calculated.
At first problem is considered without rotation and next angular
velocity increased from 0 to 50000 rev/min and stress in each stage
is calculated. The important point is that when stress become very
small in magnitude the angular velocity is critical and two cylinders
will separate. The critical speed i.e. speed of separation is calculated
in each step.
Abstract: Traffic Management and Information Systems, which rely on a system of sensors, aim to describe in real-time traffic in urban areas using a set of parameters and estimating them. Though the state of the art focuses on data analysis, little is done in the sense of prediction. In this paper, we describe a machine learning system for traffic flow management and control for a prediction of traffic flow problem. This new algorithm is obtained by combining Random Forests algorithm into Adaboost algorithm as a weak learner. We show that our algorithm performs relatively well on real data, and enables, according to the Traffic Flow Evaluation model, to estimate and predict whether there is congestion or not at a given time on road intersections.
Abstract: In recent years there has been renewal of interest in the
relation between Green IT and Cloud Computing. The growing use of
computers in cloud platform has caused marked energy consumption,
putting negative pressure on electricity cost of cloud data center. This
paper proposes an effective mechanism to reduce energy utilization in
cloud computing environments. We present initial work on the
integration of resource and power management that aims at reducing
power consumption. Our mechanism relies on recalling virtualization
services dynamically according to user-s virtualization request and
temporarily shutting down the physical machines after finish in order
to conserve energy. Given the estimated energy consumption, this
proposed effort has the potential to positively impact power
consumption. The results from the experiment concluded that energy
indeed can be saved by powering off the idling physical machines in
cloud platforms.
Abstract: Primary barrier of membrane type LNG containment system consist of corrugated 304L stainless steel. This 304L stainless steel is austenitic stainless steel which shows different material behaviors owing to phase transformation during the plastic work. Even though corrugated primary barriers are subjected to significant amounts of pre-strain due to press working, quantitative mechanical behavior on the effect of pre-straining at cryogenic temperatures are not available. In this study, pre-strain level and pre-strain temperature dependent tensile tests are carried to investigate mechanical behaviors. Also, constitutive equations with material parameters are suggested for a verification study.
Abstract: In this paper, we propose an energy efficient cluster
based communication protocol for wireless sensor network. Our
protocol considers both the residual energy of sensor nodes and the
distance of each node from the BS when selecting cluster-head. This
protocol can successfully prolong the network-s lifetime by 1)
reducing the total energy dissipation on the network and 2) evenly
distributing energy consumption over all sensor nodes. In this
protocol, the nodes with more energy and less distance from the BS
are probable to be selected as cluster-head. Simulation results with
MATLAB show that proposed protocol could increase the lifetime of
network more than 94% for first node die (FND), and more than 6%
for the half of the nodes alive (HNA) factor as compared with
conventional protocols.
Abstract: This paper presents a reliability-based approach to select appropriate wind turbine types for a wind farm considering site-specific wind speed patterns. An actual wind farm in the northern region of Iran with the wind speed registration of one year is studied in this paper. An analytic approach based on total probability theorem is utilized in this paper to model the probabilistic behavior of both turbines- availability and wind speed. Well-known probabilistic reliability indices such as loss of load expectation (LOLE), expected energy not supplied (EENS) and incremental peak load carrying capability (IPLCC) for wind power integration in the Roy Billinton Test System (RBTS) are examined. The most appropriate turbine type achieving the highest reliability level is chosen for the studied wind farm.
Abstract: Utilities use operating reserve for frequency regulation.To ensure that the operating frequency and system security are well maintained, the operating grid codes always specify that the reserve quantity and response rate should meet some prescribed levels. This paper proposes a methodology to evaluate system's contingency reserve for an isolated power network. With the presented algorithm to estimate system's frequency response characteristic, an online allocation of contingency reserve would be feasible to meet the grid codes for contingency operation. Test results from the simulated conditions, and from the actual operating data verify the merits of the proposed methodology to system's frequency control, and security.
Abstract: The world's population continues to grow at a quarter of a million people per day, increasing the consumption of energy. This has made the world to face the problem of energy crisis now days. In response to the energy crisis, the principles of renewable energy gained popularity. There are much advancement made in developing the wind and solar energy farms across the world. These energy farms are not enough to meet the energy requirement of world. This has attracted investors to procure new sources of energy to be substituted. Among these sources, extraction of energy from the waves is considered as best option. The world oceans contain enough energy to meet the requirement of world. Significant advancements in design and technology are being made to make waves as a continuous source of energy. One major hurdle in launching wave energy devices in a developing country like Pakistan is the initial cost. A simple, reliable and cost effective wave energy converter (WEC) is required to meet the nation-s energy need. This paper will present a novel design proposed by team SAS for harnessing wave energy. This paper has three major sections. The first section will give a brief and concise view of ocean wave creation, propagation and the energy carried by them. The second section will explain the designing of SAS-2. A gear chain mechanism is used for transferring the energy from the buoy to a rotary generator. The third section will explain the manufacturing of scaled down model for SAS-2 .Many modifications are made in the trouble shooting stage. The design of SAS-2 is simple and very less maintenance is required. SAS-2 is producing electricity at Clifton. The initial cost of SAS-2 is very low. This has proved SAS- 2 as one of the cost effective and reliable source of harnessing wave energy for developing countries.