Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.
Abstract: Taro Scarab beetles (Papuana uninodis, Coleoptera:
Scarabaeidae) inflict severe damage on important root crops and
plants such as Taro or Cocoyam, yam, sweet potatoes, oil palm and
coffee tea plants across Africa and Asia resulting in economic
hardship and starvation in some nations. Scoliid wasps and
Metarhizium anisopliae fungus - bio-control agents; are shown to be
able to control the population of Scarab beetle adults and larvae using
a newly created simulation model based on non-linear ordinary
differential equations that track the populations of the beetle life
cycle stages: egg, larva, pupa, adult and the population of the scoliid
parasitoid wasps, which attack beetle larvae. In spite of the challenge
driven by the longevity of the scarab beetles, the combined effect of
the larval wasps and the fungal bio-control agent is able to control
and drive down the population of both the adult and the beetle eggs
below the environmental carrying capacity within an interval of 120
days, offering the long term prospect of a stable and eco-friendly
environment; where the population of scarab beetles is: regulated by
parasitoid wasps and beneficial soil saprophytes.
Abstract: Carbon Capture & Storage (CCS) is one of the various
methods that can be used to reduce the carbon footprint of the
energy sector. This paper focuses on the absorption of CO2 from
flue gas using packed columns, whose efficiency is highly dependent
on the structure of the liquid films within the column. To study the
characteristics of liquid films a CFD solver, OpenFOAM is utilised
to solve two-phase, isothermal film flow using the volume-of-fluid
(VOF) method. The model was validated using existing experimental
data and the Nusselt theory. It was found that smaller plate inclination
angles, with respect to the horizontal plane, resulted in larger wetted
areas on smooth plates. However, only a slight improvement in
the wetted area was observed. Simulations were also performed
using a ridged plate and it was observed that these surface textures
significantly increase the wetted area of the plate. This was mainly
attributed to the channelling effect of the ridges, which helped to
oppose the surface tension forces trying to minimise the surface area.
Rivulet formations on the ridged plate were also flattened out and
spread across a larger proportion of the plate width.
Abstract: The application of agro-industrial waste in Aluminum
Metal Matrix Composites has been getting more attention as they
can reinforce particles in metal matrix which enhance the strength
properties of the composites. In addition, by applying these agroindustrial
wastes in useful way not only save the manufacturing cost
of products but also reduce the pollutions on environment. This
paper represents a literature review on a range of industrial wastes
and their utilization in metal matrix composites. The paper describes
the synthesis methods of agro-industrial waste filled metal matrix
composite materials and their mechanical, wear, corrosion, and
physical properties. It also highlights the current application and
future potential of agro-industrial waste reinforced composites in
aerospace, automotive and other construction industries.
Abstract: Lung cancer accounts for the most cancer related deaths for men as well as for women. The identification of cancer associated genes and the related pathways are essential to provide an important possibility in the prevention of many types of cancer. In this work two filter approaches, namely the information gain and the biomarker identifier (BMI) are used for the identification of different types of small-cell and non-small-cell lung cancer. A new method to determine the BMI thresholds is proposed to prioritize genes (i.e., primary, secondary and tertiary) using a k-means clustering approach. Sets of key genes were identified that can be found in several pathways. It turned out that the modified BMI is well suited for microarray data and therefore BMI is proposed as a powerful tool for the search for new and so far undiscovered genes related to cancer.