Abstract: Recently, the advanced technologies that offer high
precision product, relative easy, economical process and also rapid
production are needed to realize the high demand of ultra precision
micro part. In our research, micromanufacturing based on soft
lithography and nanopowder injection molding was investigated. The
silicone metal pattern with ultra thick and high aspect ratio succeeds to
fabricate Polydimethylsiloxane (PDMS) micro mold. The process
followed by nanopowder injection molding (PIM) by a simple vacuum
hot press. The 17-4ph nanopowder with diameter of 100 nm, succeed
to be injected and it forms green sample microbearing with thickness,
microchannel and aspect ratio is 700μm, 60μm and 12, respectively.
Sintering process was done in 1200 C for 2 hours and heating rate
0.83oC/min. Since low powder load (45% PL) was applied to achieve
green sample fabrication, ~15% shrinkage happen in the 86% relative
density. Several improvements should be done to produce high
accuracy and full density sintered part.
Abstract: A concrete structure is designed and constructed for its
purpose of use, and is expected to maintain its function for the target
durable years from when it was planned. Nevertheless, as time elapses
the structure gradually deteriorates and then eventually degrades to the
point where the structure cannot exert the function for which it was
planned. The performance of concrete that is able to maintain the level
of the performance required over the designed period of use as it has
less deterioration caused by the elapse of time under the designed
condition is referred to as Durability. There are a number of causes of
durability degradation, but especially chloride damage, carbonation,
freeze-thaw, etc are the main causes. In this study, carbonation, one of
the main causes of deterioration of the durability of a concrete
structure, was investigated via a microstructure analysis technique.
The method for the measurement of carbonation was studied using the
existing indicator method, and the method of measuring the progress
of carbonation in a quantitative manner was simultaneously studied
using a FT-IR (Fourier-Transform Infrared) Spectrometer along with
the microstructure analysis technique.
Abstract: The production of a plant can be measured in terms of
seeds. The generation of seeds plays a critical role in our social and
daily life. The fruit production which generates seeds, depends on the
various parameters of the plant, such as shoot length, leaf number,
root length, root number, etc When the plant is growing, some leaves
may be lost and some new leaves may appear. It is very difficult to
use the number of leaves of the tree to calculate the growth of the
plant.. It is also cumbersome to measure the number of roots and
length of growth of root in several time instances continuously after
certain initial period of time, because roots grow deeper and deeper
under ground in course of time. On the contrary, the shoot length of
the tree grows in course of time which can be measured in different
time instances. So the growth of the plant can be measured using the
data of shoot length which are measured at different time instances
after plantation. The environmental parameters like temperature, rain
fall, humidity and pollution are also play some role in production of
yield. The soil, crop and distance management are taken care to
produce maximum amount of yields of plant. The data of the growth
of shoot length of some mustard plant at the initial stage (7,14,21 &
28 days after plantation) is available from the statistical survey by a
group of scientists under the supervision of Prof. Dilip De. In this
paper, initial shoot length of Ken( one type of mustard plant) has
been used as an initial data. The statistical models, the methods of
fuzzy logic and neural network have been tested on this mustard
plant and based on error analysis (calculation of average error) that
model with minimum error has been selected and can be used for the
assessment of shoot length at maturity. Finally, all these methods
have been tested with other type of mustard plants and the particular
soft computing model with the minimum error of all types has been
selected for calculating the predicted data of growth of shoot length.
The shoot length at the stage of maturity of all types of mustard
plants has been calculated using the statistical method on the
predicted data of shoot length.
Abstract: This paper investigates the problem of designing a robust state-feedback controller for a class of uncertain Markovian jump nonlinear systems that guarantees the L2-gain from an exogenous input to a regulated output is less than or equal to a prescribed value. First, we approximate this class of uncertain Markovian jump nonlinear systems by a class of uncertain Takagi-Sugeno fuzzy models with Markovian jumps. Then, based on an LMI approach, LMI-based sufficient conditions for the uncertain Markovian jump nonlinear systems to have an H performance are derived. An illustrative example is used to illustrate the effectiveness of the proposed design techniques.
Abstract: In this study, we experiment on precise control outlet
temperature of water from the water cooler with hot-gas bypass
method based on PI control logic for machine tool. Recently, technical
trend for machine tools is focused on enhancement of speed and
accuracy. High speedy processing causes thermal and structural
deformation of objects from the machine tools. Water cooler has to be
applied to machine tools to reduce the thermal negative influence with
accurate temperature controlling system. The goal of this study is to
minimize temperature error in steady state. In addition, control period
of an electronic expansion valve were considered to increment of
lifetime of the machine tools and quality of product with a water
cooler.
Abstract: In this paper, we present an analytical framework for the evaluation of the uplink performance of multihop cellular networks based on dynamic time division duplex (TDD). New wireless broadband protocols, such as WiMAX, WiBro, and 3G-LTE apply TDD, and mobile communication protocols under standardization (e.g., IEEE802.16j) are investigating mobile multihop relay (MMR) as a future technology. In this paper a novel MMR TDD scheme is presented, where the dynamic range of the frame is shared to traffic resources of asymmetric nature and multihop relaying. The mobile communication channel interference model comprises of inner and co-channel interference (CCI). The performance analysis focuses on the uplink due to the fact that the effects of dynamic resource allocation show significant performance degradation only in the uplink compared to time division multiple access (TDMA) schemes due to CCI [1-3], where the downlink results to be the same or better.The analysis was based on the signal to interference power ratio (SIR) outage probability of dynamic TDD (D-TDD) and TDMA systems,which are the most widespread mobile communication multi-user control techniques. This paper presents the uplink SIR outage probability with multihop results and shows that the dynamic TDD scheme applying MMR can provide a performance improvement compared to single hop applications if executed properly.
Abstract: The paper proposes a way of parallel processing of
SURF and Optical Flow for moving object recognition and tracking.
The object recognition and tracking is one of the most important task
in computer vision, however disadvantage are many operations cause
processing speed slower so that it can-t do real-time object recognition
and tracking. The proposed method uses a typical way of feature
extraction SURF and moving object Optical Flow for reduce
disadvantage and real-time moving object recognition and tracking,
and parallel processing techniques for speed improvement. First
analyse that an image from DB and acquired through the camera using
SURF for compared to the same object recognition then set ROI
(Region of Interest) for tracking movement of feature points using
Optical Flow. Secondly, using Multi-Thread is for improved
processing speed and recognition by parallel processing. Finally,
performance is evaluated and verified efficiency of algorithm
throughout the experiment.
Abstract: In this study, we explore the use of information for inventory decision in the healthcare organization (HO). We consider the scenario when the HO can make use of the information collected from some correlated products to enhance its inventory planning. Motivated by our real world observations that HOs adopt RFID and bar-coding system for information collection purpose, we examine the effectiveness of these systems for inventory planning with Bayesian information updating. We derive the optimal ordering decision and study the issue of Pareto improvement in the supply chain. Our analysis demonstrates that RFID system will outperform the bar-coding system when the RFID system installation cost and the tag cost reduce to a level that is comparable with that of the barcoding system. We also show how an appropriately set wholesale pricing contract can achieve Pareto improvement in the HO supply chain.
Abstract: Motion estimation is the most computationally
intensive part in video processing. Many fast motion estimation
algorithms have been proposed to decrease the computational
complexity by reducing the number of candidate motion vectors.
However, these studies are for fast search algorithms themselves while
almost image and video compressions are operated with software
based. Therefore, the timing constraints for running these motion
estimation algorithms not only challenge for the video codec but also
overwhelm for some of processors. In this paper, the performance of
motion estimation is enhanced by using Intel's Streaming SIMD
Extension 2 (SSE2) technology with Intel Pentium 4 processor.
Abstract: The increasing interest on processing data created by
sensor networks has evolved into approaches to implement sensor
networks as databases. The aggregation operator, which calculates a
value from a large group of data such as computing averages or sums,
etc. is an essential function that needs to be provided when
implementing such sensor network databases. This work proposes to
add the DURING clause into TinySQL to calculate values during a
specific long period and suggests a way to implement the aggregation
service in sensor networks by applying materialized view and
incremental view maintenance techniques that is used in data
warehouses. In sensor networks, data values are passed from child
nodes to parent nodes and an aggregation value is computed at the root
node. As such root nodes need to be memory efficient and low
powered, it becomes a problem to recompute aggregate values from all
past and current data. Therefore, applying incremental view
maintenance techniques can reduce the memory consumption and
support fast computation of aggregate values.
Abstract: Repetitive systems stand for a kind of systems that
perform a simple task on a fixed pattern repetitively, which are
widely spread in industrial fields. Hence, many researchers have been
interested in those systems, especially in the field of iterative learning
control (ILC). In this paper, we propose a finite-horizon tracking
control scheme for linear time-varying repetitive systems with uncertain
initial conditions. The scheme is derived both analytically
and numerically for state-feedback systems and only numerically for
output-feedback systems. Then, it is extended to stable systems with
input constraints. All numerical schemes are developed in the forms
of linear matrix inequalities (LMIs). A distinguished feature of the
proposed scheme from the existing iterative learning control is that
the scheme guarantees the tracking performance exactly even under
uncertain initial conditions. The simulation results demonstrate the
good performance of the proposed scheme.
Abstract: This paper discusses a discrete event simulation model
for the availability analysis of weapon systems. This model
incorporates missions, operational tasks and system reliability
structures to analyze the availability of a weapon system. The
proposed simulation model consists of 5 modules: Simulation Engine,
Maintenance Organizations, System, its Mission Profile and RBD
which are based on missions and operational tasks. Simulation Engine
executes three kinds of discrete events in chronological order. The
events are mission events generated by Mission Profile, failure events
generated by System, and maintenance events executed by
Maintenance Organization. Finally, this paper shows the case study of
a system's availability analysis and mission reliability using the
simulation model.
Abstract: This paper presents an algorithm for the recognition
and tracking of moving objects, 1/10 scale model car is used to verify
performance of the algorithm. Presented algorithm for the recognition
and tracking of moving objects in the paper is as follows. SURF
algorithm is merged with Lucas-Kanade algorithm. SURF algorithm
has strong performance on contrast, size, rotation changes and it
recognizes objects but it is slow due to many computational
complexities. Processing speed of Lucas-Kanade algorithm is fast but
the recognition of objects is impossible. Its optical flow compares the
previous and current frames so that can track the movement of a pixel.
The fusion algorithm is created in order to solve problems which
occurred using the Kalman Filter to estimate the position and the
accumulated error compensation algorithm was implemented. Kalman
filter is used to create presented algorithm to complement problems
that is occurred when fusion two algorithms. Kalman filter is used to
estimate next location, compensate for the accumulated error. The
resolution of the camera (Vision Sensor) is fixed to be 640x480. To
verify the performance of the fusion algorithm, test is compared to
SURF algorithm under three situations, driving straight, curve, and
recognizing cars behind the obstacles. Situation similar to the actual is
possible using a model vehicle. Proposed fusion algorithm showed
superior performance and accuracy than the existing object
recognition and tracking algorithms. We will improve the performance
of the algorithm, so that you can experiment with the images of the
actual road environment.
Abstract: The problem of laminar fluid flow which results from
the shrinking of a permeable surface in a nanofluid has been
investigated numerically. The model used for the nanofluid
incorporates the effects of Brownian motion and thermophoresis. A
similarity solution is presented which depends on the mass suction
parameter S, Prandtl number Pr, Lewis number Le, Brownian motion
number Nb and thermophoresis number Nt. It was found that the
reduced Nusselt number is decreasing function of each dimensionless
number.
Abstract: The resident registration number was adopted for the purposes of enhanced services for resident convenience and effective performance of governmental administrative affairs. However, it has been used for identification purposes customarily and irrationally in line with the development and spread of the Internet. In response to the growing concern about the leakage of collected RRNs and possible abuses of stolen RRNs, e.g. identity theft, for crimes, the Korean Communications Commission began to take legal/regulatory actions in 2011 to minimize the online collection and use of resident registration numbers. As the use of the RRN was limited after the revision of the Act on Promotion of Information and Communications Network Utilization and Information Protection, etc., online business providers were required to have alternatives to the RRN for the purpose of identifying the user's identity and age, in compliance with the law, and settling disputes with customers. This paper presents means of verifying the personal identity by taking advantage of the commonly used infrastructure and simply replacing personal information entered and stored, without requiring users to enter their RRNs.
Abstract: Time full of changes which is associated with globalization, tougher competition, changes in the structures of markets and economic downturn, that all force companies to think about their competitive advantages. These changes can bring the company a competitive advantage and that can help improve competitive position in the market. Policy of the European Union is focused on the fast growing innovative companies which quickly respond to market demands and consequently increase its competitiveness. To meet those objectives companies need the right conditions and support of their state.
Abstract: This paper deals with efficient quadrature formulas involving functions that are observed only at fixed sampling points. The approach that we develop is derived from efficient continuous quadrature formulas, such as Gauss-Legendre or Clenshaw-Curtis quadrature. We select nodes at sampling positions that are as close as possible to those of the associated classical quadrature and we update quadrature weights accordingly. We supply the theoretical quadrature error formula for this new approach. We show on examples the potential gain of this approach.