Abstract: The paper discusses a computationally efficient
method for the design of prototype filters required for the
implementation of an M-band cosine modulated filter bank. The
prototype filter is formulated as an optimum interpolated FIR filter.
The optimum interpolation factor requiring minimum number of
multipliers is used. The model filter as well as the image suppressor
will be designed using the Kaiser window. The method will seek to
optimize a single parameter namely cutoff frequency to minimize the
distortion in the overlapping passband.
Abstract: This paper studies dynamic stability of homogeneous
beams with piezoelectric layers subjected to periodic axial
compressive load that is simply supported at both ends lies on a
continuous elastic foundation. The displacement field of beam is
assumed based on Bernoulli-Euler beam theory. Applying the
Hamilton's principle, the governing dynamic equation is established.
The influences of applied voltage, foundation coefficient and
piezoelectric thickness on the unstable regions are presented. To
investigate the accuracy of the present analysis, a compression study
is carried out with a known data.
Abstract: The purpose of the study reported here was designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. A questionnaire was developed to designing Information Dissemination System. The questionnaire was distributed to 96 extension agents who work for Management of Extension and Farming System of Khuzestan province of Iran. Data collected were analyzed using the Statistical Package for the Social Sciences (SPSS). Appropriate statistical procedures for description (frequencies, percent, means, and standard deviations) were used. In this study there was a significant relationship between the age , IT skill and knowledge, years of extension work, the extend of information seeking motivation, level of job satisfaction and level of education with use of information technology by extension agent. According to extension agents five factors were ranked respectively as five top essential items to designing Information Dissemination System (IDS) based E-learning in agricultural of Iran. These factors include: 1) Establish communication between farmers, coordinators (extension agents), agricultural experts, research centers, and community by information technology. 2) The communication between all should be mutual. 3) The information must be based farmers need. 4) Internet used as a facility to transfer the advanced agricultural information to the farming community. 5) Farmers can be illiterate and speak a local and they are not expected to use the system directly. Knowledge produced by the agricultural scientist must be transformed in to computer understandable presentation. To designing Information Dissemination System, electronic communication, in the agricultural society and rural areas must be developed. This communication must be mutual between all factors.
Abstract: In this study an extensive experimental research is
carried out to develop a better understanding of the effects of Piano Key (PK) weir geometry on weir flow threshold submergence.
Experiments were conducted in a 12 m long, 0.4 m wide and 0.7 m deep rectangular glass wall flume. The main objectives were to
investigate the effect of the PK weir geometries including the weir
length, weir height, inlet-outlet key widths, upstream and
downstream apex overhangs, and slopped floors on threshold submergence and study the hydraulic flow characteristics. From the
experimental results, a practical formula is proposed to evaluate the flow threshold submergence over PK weirs.
Abstract: Automated material handling is given prime
importance in the semi automated and automated facilities since it
provides solution to the gigantic problems related to inventory and
also support the latest philosophies like just in time production JIT
and lean production. Automated storage and retrieval system is an
antidote (if designed properly) to the facility sufferings like getting
the right material , materials getting perished, long cycle times or
many other similar kind of problems. A working model of automated
storage and retrieval system (AS/RS) is designed and developed
under the design parameters specified by Material Handling Industry
of America (MHIA). Later on analysis was carried out to calculate
the throughput and size of the machine. The possible implementation
of this technology in local scenario is also discussed in this paper.
Abstract: The operating control parameters of injection
flushing type of electrical discharge machining process on stainless
steel 304 workpiece using copper tools are being optimized
according to its individual machining characteristic i.e. Electrode
Wear Ratio (EWR). Higher EWR would give bad dimensional
precision for the EDM machined workpiece because of high
electrode wear. Hence, the quality characteristic for EWR is set to
lower-the-better to achieve the optimum dimensional precision for
the machined workpiece. Taguchi method has been used for the
construction, layout and analysis of the experiment for EWR
machining characteristic. The use of Taguchi method in the
experiment saves a lot of time and cost of preparing and machining
the experiment samples. Therefore, an L18 Orthogonal array
which was the fundamental component in the statistical design of
experiments has been used to plan the experiments and Analysis of
Variance (ANOVA) is used to determine the optimum machining
parameters for this machining characteristic. The control
parameters selected for this optimization experiments are polarity,
pulse on duration, discharge current, discharge voltage, machining
depth, machining diameter and dielectric liquid pressure. The
result had shown that negative polarity machining parameter
setting will decreases EWR.
Abstract: This study used positivist quantitative approach to examine the mathematical concepts acquisition of- KS4 (14-16) Special Education Needs (SENs) students within the school sector education in England. The research is based on a pilot study and the design is completely holistic in its approach with mixing methodologies. The study combines the qualitative and quantitative methods of approach in gathering formative data for the design process. Although, the approach could best be described as a mix method, fundamentally with a strong positivist paradigm, hence my earlier understanding of the differentiation of the students, student – teacher body and the various elements of indicators that is being measured which will require an attenuated description of individual research subjects. The design process involves four phases with five key stages which are; literature review and document analysis, the survey, interview, and observation; then finally the analysis of data set. The research identified the need for triangulation with Reid-s phases of data management providing scaffold for the study. The study clearly identified the ideological and philosophical aspects of educational research design for the study of mathematics by the special education needs (SENs) students in England using the virtual learning environment (VLE) platform.
Abstract: This paper presents the elastic buckling of
homogeneous beams with a pair of piezoelectric layers surface
bonded on both sides of the beams. The displacement field of beam is
assumed based on the Engesser-Timoshenko beam theory.
Applying the Hamilton's principle, the equilibrium equation is
established. The influences of applied voltage, dimensionless
geometrical parameter and piezoelectric thickness on the critical
buckling load of beam are presented. To investigate the accuracy of
the present analysis, a compression study is carried out with a known
data.
Abstract: The main issue in sweetening natural gas is H2S
dissociation. The present study is concerned with simulating thermal
dissociation of H2S in industrial natural gas carbon black furnace.
The comparison of calculated results against experimental
measurements shows good agreement. The results show that sulfur
derived from H2S thermal dissociation peaked at φ=0.95. H2S
thermal dissociation is enhanced in equivalence ratio upper than 1
and H2S oxidization is increased in equivalence ratio lower than 1.
H2 concentration of H2S thermal dissociation is increased with
increase of equivalence ratio up to 1. Also, H2S concentration
decreased in outlet as equivalence ratio increases. H2S thermal
dissociation to hydrogen and Sulfur reduces its toxic characteristics
and make economical benefits.
Abstract: The present work was conducted for Arsenic (III)
removal, which one of the most poisonous groundwater pollutants, by
synthetic nano size zerovalent iron (nZVI). Batch experiments were
performed to investigate the influence of As (III), nZVI
concentration, pH of solution and contact time on the efficiency of As
(III) removal. nZVI was synthesized by reduction of ferric chloride
by sodium borohydrid. SEM and XRD were used to determine
particle size and characterization of produced nanoparticles. Up to
99.9% removal efficiency for arsenic (III) was obtained by nZVI
dosage of 1 g/L at time equal to 10 min. and pH=7. It could be
concluded that the removal efficiency were enhanced with increasing
of ZVI dosage and reaction time, but decreased with increasing of
arsenic concentration and pH for nano sized ZVI. nZVI presented an
outstanding ability to remove As (III) due to not only a high surface
area and low particle size but also to high inherent activity.
Abstract: Data from 1731 Gentile di Puglia lambs, sired by 65 rams over a 5-year period were analyzed by a mixed model to estimate the variance components for heritability. The considered growth traits were: birth weight (BW), weight at 30 days of age (W30) and average daily gain from birth to 30 days of age (DG). Year of birth, sex of lamb, type of birth (single or twin), dam age at lambing and farm were significant sources of variation for all the considered growth traits. The average lamb weights were 3.85±0.16 kg at birth, 9.57±0.91 kg at 30 days of age and the average daily gain was 191±14 g. Estimates of heritability were 0.33±0.05, 0.41±0.06 and 0.16±0.05 respectively for the same traits. These values suggest there is a good opportunity to improve Gentile di Puglia lambs by selecting animals for growth traits.
Abstract: Air pollution is a major environmental health
problem, affecting developed and developing countries around the
world. Increasing amounts of potentially harmful gases and
particulate matter are being emitted into the atmosphere on a global
scale, resulting in damage to human health and the environment.
Petroleum-related air pollutants can have a wide variety of adverse
environmental impacts. In the crude oil production sectors, there is a
strong need for a thorough knowledge of gaseous emissions resulting
from the flaring of associated gas of known composition on daily
basis through combustion activities under several operating
conditions. This can help in the control of gaseous emission from
flares and thus in the protection of their immediate and distant
surrounding against environmental degradation.
The impacts of methane and non-methane hydrocarbons emissions
from flaring activities at oil production facilities at Kuwait Oilfields
have been assessed through a screening study using records of flaring
operations taken at the gas and oil production sites, and by analyzing
available meteorological and air quality data measured at stations
located near anthropogenic sources. In the present study the
Industrial Source Complex (ISCST3) Dispersion Model is used to
calculate the ground level concentrations of methane and nonmethane
hydrocarbons emitted due to flaring in all over Kuwait
Oilfields.
The simulation of real hourly air quality in and around oil
production facilities in the State of Kuwait for the year 2006,
inserting the respective source emission data into the ISCST3
software indicates that the levels of non-methane hydrocarbons from
the flaring activities exceed the allowable ambient air standard set by
Kuwait EPA. So, there is a strong need to address this acute problem
to minimize the impact of methane and non-methane hydrocarbons
released from flaring activities over the urban area of Kuwait.
Abstract: Due to the stringent legislation for emission of diesel
engines and also increasing demand on fuel consumption, the
importance of detailed 3D simulation of fuel injection, mixing and
combustion have been increased in the recent years. In the present
work, FIRE code has been used to study the detailed modeling of
spray and mixture formation in a Caterpillar heavy-duty diesel
engine. The paper provides an overview of the submodels
implemented, which account for liquid spray atomization, droplet
secondary break-up, droplet collision, impingement, turbulent
dispersion and evaporation. The simulation was performed from
intake valve closing (IVC) to exhaust valve opening (EVO). The
predicted in-cylinder pressure is validated by comparing with
existing experimental data. A good agreement between the predicted
and experimental values ensures the accuracy of the numerical
predictions collected with the present work. Predictions of engine
emissions were also performed and a good quantitative agreement
between measured and predicted NOx and soot emission data were
obtained with the use of the present Zeldowich mechanism and
Hiroyasu model. In addition, the results reported in this paper
illustrate that the numerical simulation can be one of the most
powerful and beneficial tools for the internal combustion engine
design, optimization and performance analysis.
Abstract: Environment-assisted cracking (EAC) is one of the most serious causes of structural failure over a broad range of industrial applications including offshore structures. In EAC condition there is not a definite relation such as Paris equation in Linear Elastic Fracture Mechanics (LEFM). According to studying and searching a lot what the researchers said either a material has contact with hydrogen or any other corrosive environment, phenomenon of electrical and chemical reactions of material with its environment will be happened. In the literature, there are many different works to consider fatigue crack growing and solve it but they are experimental works. Thus, in this paper, authors have an aim to evaluate mathematically the pervious works in LEFM. Obviously, if an environment is more sour and corrosive, the changes of stress intensity factor is more and the calculation of stress intensity factor is difficult. A mathematical relation to deal with the stress intensity factor during the diffusion of sour environment especially hydrogen in a marine pipeline is presented. By using this relation having and some experimental relation an analytical formulation will be presented which enables the fatigue crack growth and critical crack length under cyclic loading to be predicted. In addition, we can calculate KSCC and stress intensity factor in the pipeline caused by EAC.
Abstract: This study presents the performance of membrane
bioreactor in treating high phosphate wastewater. The laboratory
scale MBR was operated at permeate flux of 25 L/m2.h with a hollow
fiber membrane (polypropylene, approx. pore size 0.01 - 0.2 μm) at
hydraulic retention time (HRT) of 12 hrs. Scanning electron
microscopy (SEM) and energy diffusive X-ray (EDX) analyzer were
used to characterize the membrane foulants. Results showed that the
removal efficiencies of COD, TSS, NH3-N and PO4
3- were 93, 98, 80
and 30% respectively. On average 91% of influent soluble microbial
products (SMP) were eliminated, with the eliminations of
polysaccharides mostly above 80%. The main fouling resistance was
cake resistance. It should be noted that SMP were found in major
portions of mixed liquor that played a relatively significant role in
membrane fouling. SEM and EDX analyses indicated that the
foulants covering the membrane surfaces comprises not only organic
substances but also inorganic elements including Mg, Ca, Al, K and
P.