Abstract: This paper describes a 2.4 GHz passive switch mixer
and a 5/2.5 GHz voltage-controlled negative Gm oscillator (VCO)
with an inversion-mode MOS varactor. Both circuits are implemented
using a 1P8M 0.13 μm process. The switch mixer has an input
referred 1 dB compression point of -3.89 dBm and a conversion
gain of -0.96 dB when the local oscillator power is +2.5 dBm.
The VCO consumes only 1.75 mW, while drawing 1.45 mA from a
1.2 V supply voltage. In order to reduce the passives size, the VCO
natural oscillation frequency is 5 GHz. A clocked CMOS divideby-
two circuit is used for frequency division and quadrature phase
generation. The VCO has a -109 dBc/Hz phase noise at 1 MHz
frequency offset and a 2.35-2.5 GHz tuning range (after the frequency
division), thus complying with ZigBee requirements.
Abstract: Nowadays, new home appliances and office appliances
have been developed that communicate with users through the
Internet, for remote monitor and remote control. However, developments
and sales of these new appliances are just started, then,
many products in our houses and offices do not have these useful
functions. In few years, we add these new functions to the outlet,
it means multifunctional electrical power socket plug adapter. The
outlet measure power consumption of connecting appliances, and it
can switch power supply to connecting appliances, too. Using this
outlet, power supply of old appliances can be control and monitor.
And we developed the interface system using web browser to operate
it from users[1]. But, this system need to set up LAN cables between
outlets and so on. It is not convenience that cables around rooms. In
this paper, we develop the system that use wireless mobile ad hoc
network instead of wired LAN to communicate with the outlets.
Abstract: Firstly, research and development on RFID focuses on
manufacturing and retail sectors, because it can improve supply chain
efficiency. But, now a variety of field is considered the next research
area for Radio Frequency Identification (RFID). Although RFID is
infancy, RFID technology has great potential in power industry to
significantly reduce cost, and improve quality of power supply. To
complement the limitation of RFID, we adopt the WSN (Wireless
Sensor Network) technology. However, relevant experience is limited,
the challenge will be to derive requirement from business practice and
to determine whether it is possible or not. To explore this issue, we
conduct a case study on implementing power facility management
system using RFID/WSN in Korea Electric Power Corporation
(KEPCO). In this paper we describe requirement from power industry.
And we introduce design and implementation of the test bed.
Abstract: In this work a new platform for mobile-health systems is
presented. System target application is providing decision support to
rescue corps or military medical personnel in combat areas. Software
architecture relies on a distributed client-server system that manages a
wireless ad-hoc networks hierarchy in which several different types of
client operate. Each client is characterized for different hardware and
software requirements. Lower hierarchy levels rely in a network of
completely custom devices that store clinical information and patient
status and are designed to form an ad-hoc network operating in the
2.4 GHz ISM band and complying with the IEEE 802.15.4 standard
(ZigBee). Medical personnel may interact with such devices, that are
called MICs (Medical Information Carriers), by means of a PDA
(Personal Digital Assistant) or a MDA (Medical Digital Assistant),
and transmit the information stored in their local databases as well as
issue a service request to the upper hierarchy levels by using IEEE
802.11 a/b/g standard (WiFi). The server acts as a repository that
stores both medical evacuation forms and associated events (e.g., a
teleconsulting request). All the actors participating in the diagnostic
or evacuation process may access asynchronously to such repository
and update its content or generate new events. The designed system
pretends to optimise and improve information spreading and flow
among all the system components with the aim of improving both
diagnostic quality and evacuation process.
Abstract: This paper deals with the design, development & implementation of a temperature sensor using zigbee. The main aim of the work undertaken in this paper is to sense the temperature and to display the result on the LCD using the zigbee technology. ZigBee operates in the industrial, scientific and medical (ISM) radio bands; 868 MHz in Europe, 915 MHz in the USA and 2.4 GHz in most jurisdictions worldwide. The technology is intended to be simpler and cheaper than other WPANs such as Bluetooth. The most capable ZigBee node type is said to require only about 10 % of the software of a typical Bluetooth or Wireless Internet node, while the simplest nodes are about 2 %. However, actual code sizes are much higher, more like 50 % of the Bluetooth code size. ZigBee chip vendors have announced 128-kilobyte devices. In this work undertaken in the design & development of the temperature sensor, it senses the temperature and after amplification is then fed to the micro controller, this is then connected to the zigbee module, which transmits the data and at the other end the zigbee reads the data and displays on to the LCD. The software developed is highly accurate and works at a very high speed. The method developed shows the effectiveness of the scheme employed.
Abstract: This paper presents the development of analysis tools
for Home Agriculture project. The tools are required for monitoring
the condition of greenhouse which involves two components:
measurement hardware and data analysis engine. Measurement
hardware is functioned to measure environment parameters such as
temperature, humidity, air quality, dust and etc while analysis tool is
used to analyse and interpret the integrated data against the condition
of weather, quality of health, irradiance, quality of soil and etc. The
current development of the tools is completed for off-line data
recorded technique. The data is saved in MMC and transferred via
ZigBee to Environment Data Manager (EDM) for data analysis.
EDM converts the raw data and plot three combination graphs. It has
been applied in monitoring three months data measurement for
irradiance, temperature and humidity of the greenhouse..
Abstract: With increasing utilization of the wireless devices in
different fields such as medical devices and industrial fields, the
paper presents a method for simplify the Bluetooth packets with
throughput enhancing. The paper studies a vital issue in wireless
communications, which is the throughput of data over wireless
networks. In fact, the Bluetooth and ZigBee are a Wireless Personal
Area Network (WPAN). With taking these two systems competition
consideration, the paper proposes different schemes for improve the
throughput of Bluetooth network over a reliable channel. The
proposition depends on the Channel Quality Driven Data Rate
(CQDDR) rules, which determines the suitable packet in the
transmission process according to the channel conditions. The
proposed packet is studied over additive White Gaussian Noise
(AWGN) and fading channels. The Experimental results reveal the
capability of extension of the PL length by 8, 16, 24 bytes for classic
and EDR packets, respectively. Also, the proposed method is suitable
for the low throughput Bluetooth.
Abstract: In this paper, we proposed an efficient data
compression strategy exploiting the multi-resolution characteristic of
the wavelet transform. We have developed a sensor node called
“Smart Sensor Node; SSN". The main goals of the SSN design are
lightweight, minimal power consumption, modular design and robust
circuitry. The SSN is made up of four basic components which are a
sensing unit, a processing unit, a transceiver unit and a power unit.
FiOStd evaluation board is chosen as the main controller of the SSN
for its low costs and high performance. The software coding of the
implementation was done using Simulink model and MATLAB
programming language. The experimental results show that the
proposed data compression technique yields recover signal with good
quality. This technique can be applied to compress the collected data
to reduce the data communication as well as the energy consumption
of the sensor and so the lifetime of sensor node can be extended.
Abstract: This paper presents one of the best applications of wireless sensor network for campus Monitoring. With the help of PIR sensor, temperature sensor and humidity sensor, effective utilization of energy resources has been implemented in one of rooms of Sharda University, Greater Noida, India. The RISC microcontroller is used here for analysis of output of sensors and providing proper control using ZigBee protocol. This wireless sensor module presents a tremendous power saving method for any campus
Abstract: In this paper, we argue the security protocols of
ZigBee wireless sensor network in MAC layer. AES 128-bit
encryption algorithm in CCM* mode is secure transferred data;
however, AES-s secret key will be break within nearest future.
Efficient public key algorithm, ECC has been mixed with AES to
rescue the ZigBee wireless sensor from cipher text and replay attack.
Also, the proposed protocol can parallelize the integrity function to
increase system performance.
Abstract: A direct downconversion receiver implemented in 0.13 μm 1P8M process is presented. The circuit is formed by a single-end LNA, an active balun for conversion into balanced mode, a quadrature double-balanced passive switch mixer and a quadrature voltage-controlled oscillator. The receiver operates in the 2.4 GHz ISM band and complies with IEEE 802.15.4 (ZigBee) specifications. The circuit exhibits a very low noise figure of only 2.27 dB and dissipates only 14.6 mW with a 1.2 V supply voltage and is hence suitable for low-power applications.