Abstract: A mechanically-resonant torsional spring scanner was developed in a recent study. Various methods were developed to improve the angular displacement of the scanner while maintaining the scanner frequency. However the effects of rotor magnet radial position on scanner characteristics were not well investigated. In this study, the relationships between the magnet position and the scanner characteristics such as natural frequency, angular displacement and stress level were studied. A finite element model was created and an average deviation of 3.18% was found between the simulation and experimental results, qualifying the simulation results as a guide for further investigations. Three magnet positions on the transverse oscillating suspended plate were investigated by finite element analysis (FEA) and one of the positions were selected as the design position. The magnet position with the longest distance from the twist axis of mirror was selected since it attains minimum stress level, while exceeding the minimum critical flicker frequency and delivering the targeted angular displacement to the scanner.
Abstract: In addition to the increase of the material removal rate or surface rate, or the improvement of the surface quality, which are the main aims of the development of manufacturing technology, a growing number of other manufacturing requirements have appeared in the machining of workpiece surfaces. Among these it is becoming increasingly dominant to generate a surface topography in finishing operations which meets more closely the needs of operational requirements.
These include the examination of the surface periodicity and/or ensuring that the twist-structure values are within the limits (or even preventing its occurrence) in specified cases such as on the sealing surfaces of rotating shafts or on the inside working surfaces of needle roller bearings. In the view of the measurement the twist has different parameters from surface roughness, which must be determined for the machining procedures. Therefore in this paper the alteration of the theoretical values of the parameters determining twist structure are studied as a function of the kinematic properties.
Abstract: Experimental investigation of heat transfer and
friction factor characteristics of circular tube fitted with 300 right-left helical screw inserts with 100 mm spacer of different twist ratio has
been presented for laminar and turbulent flow.. The experimental data obtained were compared with those obtained from plain tube
published data. The heat transfer coefficient enhancement for 300 RL
inserts with 100 mm spacer is quite comparable with for 300 R-L
inserts. Performance evaluation analysis has been made and found
that the performance ratio increases with increasing Reynolds number
and decreasing twist ration with the maximum for the twist ratio 2.93.
Also, the performance ratio of more than one indicates that the type
of twist inserts can be used effectively for heat transfer augmentation.
Abstract: In this study, we propose the chaotic cipher combined with Mersenne Twister that is an extremely good pseudo-random number generator for the secure communications. We investigate the Lyapunov exponent of the proposed system, and evaluate the randomness performance by comparing RC4 and the chaotic cipher. In these results, our proposed system gets high chaotic property and more randomness than the conventional ciphers.
Abstract: The contribution deals with problem of take-off phase of back somersault with twisting with various numbers of twists along longitudinal body axis. The aim was to evaluate the changes in angles during transition phase from back handspring to back somersault using 3D kinematic analysis of the somersaults. We used Simi Motion System for the 3D kinematic analysis of the observed gymnastic element performed by Czech Republic female representative and 2008 Summer Olympic Games participant. The results showed that the higher the number of twists, the smaller the touchdown angle in which the gymnasts lands on the pad in the beginning of take-off phase. In back somersault with one twist (180°) the average angle is 54°, in 1080° back somersault the average angle is 45.9°. These results may help to improve technical training of sports gymnasts.
Abstract: The major focus of this work was to characterize hydrodynamics in a packed-bed with and without static mixer by using Computational Fluid Dynamic (CFD). The commercial software: COMSOL MULTIPHYSICSTM Version 3.3 was used to simulate flow fields of mixed-gas reactants i.e. CO and H2. The packed-bed was a single tube with the inside diameter of 0.8 cm and the length of 1.2 cm. The static mixer was inserted inside the tube. The number of twisting elements was 1 with 0.8 cm in diameter and 1.2 cm in length. The packed-bed with and without static mixer were both packed with approximately 700 spherical structures representing catalyst pellets. Incompressible Navier-Stokes equations were used to model the gas flow inside the beds at steady state condition, in which the inlet Reynolds Number (Re) was 2.31. The results revealed that, with the insertion of static mixer, the gas was forced to flow radially inward and outward between the central portion of the tube and the tube wall. This could help improving the overall performance of the packed-bed, which could be utilized for heterogeneous catalytic reaction such as reforming and Fischer- Tropsch reactions.
Abstract: The influence of twist arrangement on the temperature
distribution in an annular diffuser fitted with twisted rectangular hub
is investigated. Different pitches (Y = 120 mm, 100 mm, 80 mm, and
60 mm) for the twist arrangements are simulated to be compared. The
geometry of the annular diffuser and the inlet condition for the hub
arrangements are kept constant. The result reveals that using twisted
rectangular hub insert with different pitches will force the
temperature to distribute in a circular direction. However,
temperature distribution will be enhanced with the length pitch
increases.
Abstract: In this paper, an analytical approach is used to study the coupled lateral-torsional vibrations of laminated composite beam. It is known that in such structures due to the fibers orientation in various layers, any lateral displacement will produce a twisting moment. This phenomenon is modeled by the bending-twisting material coupling rigidity and its main feature is the coupling of lateral and torsional vibrations. In addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies. Then, the governing differential equations are derived using the Hamilton-s principle and the mathematical model matches the Timoshenko beam model when neglecting the effect of bending-twisting rigidity. The equations of motion which form a system of three coupled PDEs are solved analytically to study the free vibrations of the beam in lateral and rotational modes due to the bending, as well as the torsional mode caused by twisting. The analytic solution is carried out in three steps: 1) assuming synchronous motion for the kinematic variables which are the lateral, rotational and torsional displacements, 2) solving the ensuing eigenvalue problem which contains three coupled second order ODEs and 3) imposing different boundary conditions related to combinations of simply, clamped and free end conditions. The resulting natural frequencies and mode shapes are compared with similar results in the literature and good agreement is achieved.
Abstract: The dynamic model of a drill in drilling process was
proposed and investigated in this study. To assure a good drilling quality, the vibration variation on the drill tips during high speed
drilling is needed to be investigated. A pre-twisted beam is used to
simulate the drill. The moving Winkler-Type elastic foundation is used to characterize the tip boundary variation in drilling. Due to the
variation of the drill depth, a time dependent dynamic model for the drill is proposed. Results simulated from this proposed model indicate that an abrupt natural frequencies drop are experienced as the drill tip
tough the workpiece, and a severe vibration is induced. The effects of parameters, e.g. drilling speed, depth, drill size and thrust force on the
drill tip responses studied.
Abstract: Without uncertainty by applying external loads on
beams, bending is created. The created bending in I-beams, puts one
of the flanges in tension and the other one in compression. With increasing of bending, compression flange buckled and beam in out
of its plane direction twisted, this twisting well-known as Lateral Torsional Buckling. Providing bending moment varieties along the
beam, the critical moment is greater than the case its under pure bending. In other words, the value of bending gradient coefficient is
always greater than unite. In this article by the use of " ANSYS 10.0" software near 80 3-D finite element models developed for the
propose of analyzing beams` lateral torsional buckling and surveying influence of slenderness on beams' bending gradient coefficient.
Results show that, presented Cb coefficient via AISC is not correct for some of beams and value of this coefficient is smaller than what proposed by AISC. Therefore instead of using a constant Cb for each
case of loading , a function with two criterion for calculation of Cb coefficient for some cases is proposed.
Abstract: This paper deals with the problem of non-uniform
torsion in thin-walled elastic beams with asymmetric cross-section,
removing the basic concept of a fixed center of twist, necessary in the
Vlasov-s and Benscoter-s theories to obtain a warping stress field
equivalent to zero. In this new torsion/flexure theory, despite of the
classical ones, the warping function will punctually satisfy the first
indefinite equilibrium equation along the beam axis and it wont- be
necessary to introduce the classical congruence condition, to take into
account the effect of the beam restraints. The solution, based on the
Fourier development of the displacement field, is obtained assuming
that the applied external torque is constant along the beam axis and
on both beam ends the unit twist angle and the warping axial
displacement functions are totally restrained.
Finally, in order to verify the feasibility of the proposed method
and to compare it with the classical theories, two applications are
carried out. The first one, relative to an open profile, is necessary to
test the numerical method adopted to find the solution; the second
one, instead, is relative to a simplified containership section,
considered as full restrained in correspondence of two adjacent
transverse bulkheads.
Abstract: Optical 1x12 fused-taper-twisted polymer optical fiber (POF) couplers has been fabricated by a perform technique. Characterization of the coupler which proposed to be used in passive night vision application to tracking a blind sport area was reported. During the development process of fused-taper-twisted POF couplers was carried out, red LED fully utilized to be injected into the couplers to test the quality of fabricated couplers. Some characterization parameters, such as optical output power, POFs attenuation characteristics and power losses on the network were observed. The maximum output power efficiency of the coupler is about 40%, but it can be improved gradually through experience and practice.
Abstract: The present work is motivated by the idea that the
layer deformation in anisotropic elasticity can be estimated from the
theory of interfacial dislocations. In effect, this work which is an
extension of a previous approach given by one of the authors
determines the anisotropic displacement fields and the critical
thickness due to a complex biperiodic network of MDs lying just
below the free surface in view of the arrangement of dislocations.
The elastic fields of such arrangements observed along interfaces
play a crucial part in the improvement of the physical properties of
epitaxial systems. New results are proposed in anisotropic elasticity
for hexagonal networks of MDs which contain intrinsic and extrinsic
stacking faults. We developed, using a previous approach based on
the relative interfacial displacement and a Fourier series formulation
of the displacement fields, the expressions of elastic fields when
there is a possible dissociation of MDs. The numerical investigations
in the case of the observed system Si/(111)Si with low twist angles
show clearly the effect of the anisotropy and thickness when the
misfit networks are dissociated.
Abstract: In this paper the Differential Quadrature Method (DQM) is employed to study the coupled lateral-torsional free vibration behavior of the laminated composite beams. In such structures due to the fiber orientations in various layers, the lateral displacement leads to a twisting moment. The coupling of lateral and torsional vibrations is modeled by the bending-twisting material coupling rigidity. In the present study, in addition to the material coupling, the effects of shear deformation and rotary inertia are taken into account in the definition of the potential and kinetic energies of the beam. The governing differential equations of motion which form a system of three coupled PDEs are solved numerically using DQ procedure under different boundary conditions consist of the combinations of simply, clamped, free and other end conditions. The resulting natural frequencies and mode shapes for cantilever beam are compared with similar results in the literature and good agreement is achieved.
Abstract: A complete CAD procedure to model a twisted-bladed
vertical-axis wind turbine (VAWT) is presented with the aim of
determining some practical guidelines to be used for the generation
of an easily-meshable CAD geometry to be adopted as the basis of
both CFD and FEM numerical simulations.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.
Abstract: For smaller mechatronic device, especially for micro
Electronic system, a micro machining is a must. However, most
investigations on vibration of a mill have been limited to the
traditional type mill. In this article, vibration and dynamic
characteristics of a micro mill were investigated in this study. The
trend towards higher precision manufacturing technology requires
producing miniaturized components. To improve micro-milled
product quality, obtain a higher production rate and avoid milling
breakage, the dynamic characteristics of micro milling must be
studied. A stepped pre-twisted mill is used to simulate the micro mill.
The finite element analysis is employed in this work. The flute length
and diameter effects of the micro mill are considered. It is clear that
the effects of micro mill shape parameters on vibration in a micro mill
are significant.
Abstract: In recent five decades, textured yarns of polyester fiber produced by false twist method are the most
important and mass-produced manmade fibers. There are
many parameters of cross section which affect the physical and mechanical properties of textured yarns. These parameters
are surface area, perimeter, equivalent diameter, large
diameter, small diameter, convexity, stiffness, eccentricity, and hydraulic diameter. These parameters were evaluated by
digital image processing techniques. To find trends between production criteria and evaluated parameters of cross section, three criteria of production line have been adjusted and different types of yarns were produced. These criteria are
temperature, drafting ratio, and D/Y ratio. Finally the relations between production criteria and cross section parameters were
considered. The results showed that the presented technique can recognize and measure the parameters of fiber cross section in acceptable accuracy. Also, the optimum condition
of adjustments has been estimated from results of image analysis evaluation.
Abstract: An experimental campaign of measurements for a
Darrieus vertical-axis wind turbine (VAWT) is presented for open
field conditions. The turbine is characterized by a twisted bladed
design, each blade being placed at a fixed distance from the rotational
shaft. The experimental setup to perform the acquisitions is described.
The results are lower than expected, due to the high influence of the
wind shear.
Abstract: This paper proposes a three-dimensional motion capture and feedback system of flying disc throwing action learners with use of Kinect device. Rather than conventional 3-D motion capture system, Kinect has advantages of cost merit, easy system development and operation. A novice learner of flying disc is trained to keep arm movement in steady height, to twist the waist, and to stretch the elbow according to the waist angle. The proposing system captures learners- body movement, checks their skeleton positions in pre-motion / motion / post-motion in several ways, and displays feedback messages to refine their actions.