Abstract: This study investigates the capacity of granular
activated carbon (GAC) for the storage of methane through the
equilibrium adsorption. An experimental apparatus consist of a dual
adsorption vessel was set up for the measurement of equilibrium
adsorption of methane on GAC using volumetric technique (pressure
decay). Experimental isotherms of methane adsorption were
determined by the measurement of equilibrium uptake of methane in
different pressures (0-50 bar) and temperatures (285.15-328.15°K).
The experimental data was fitted to Freundlich and Langmuir
equations to determine the model isotherm. The results show that the
experimental data is equally well fitted by the both model isotherms.
Using the experimental data obtained in different temperatures the
isosteric heat of methane adsorption was also calculated by the
Clausius-Clapeyron equation from the Sips isotherm model. Results
of isosteric heat of adsorption show that decreasing temperature or
increasing methane uptake by GAC decrease the isosteric heat of
methane adsorption.
Abstract: Fly ash is a significant waste that is released of
thermal power plants and defined as very fine particles that are drifted upward with up taken by the flue gases due to the burning of
used coal [1]. The fly-ash is capable of removing organic
contaminants in consequence of high carbon content, a large surface area per unit volume and contained heavy metals. Therefore, fly ash
is used as an effective coagulant and adsorbent by pelletization [2, 3].
In this study, the possibility of use of fly ash taken from Turkey like low-cost adsorbent for adsorption of zinc ions found in waste
water was investigated. The fly ash taken from Turkey was pelletized with bentonite and molass to evaluate the adsorption capaticity. For
this purpose; analyses such as sieve analysis, XRD, XRF, FTIR and SEM were performed. As a result, it was seen that pellets prepared
from fly ash, bentonite and molass would be used for zinc adsorption.
Abstract: Arthrobacter viscosus biomass was used for Cr(VI)
biosorption. The effect of pH on Cr(VI) reduction and removal from
aqueous solution was studied in the range of 1-4. The Cr(VI) removal
involves both redox reaction and adsorption of metal ions on biomass
surface. The removal rate of Cr(VI) was enhanced by very acid
conditions, while higher solution pH values favored the removal of
total chromium. The best removal efficiency and uptake were
reached at pH 4, 72.5 % and 12.6 mgCr/gbiomass, respectively.
Abstract: In this study the adsorption of Cu (II) ions from aqueous solutions on synthetic zeolite NaA was evaluated. The effect of solution temperature and the determination of the kinetic parameters of adsorption of Cu(II) from aqueous solution on zeolite NaA is important in understanding the adsorption mechanism. Variables of the system include adsorption time, temperature (293- 328K), initial solution concentration and pH for the system. The sorption kinetics of the copper ions were found to be strongly dependent on pH (the optimum pH 3-5), solute ion concentration and temperature (293 – 328 K). It was found, the pseudo-second-order model was the best choice among all the kinetic models to describe the adsorption behavior of Cu(II) onto ziolite NaA, suggesting that the adsorption mechanism might be a chemisorptions process The activation energy of adsorption (Ea) was determined as Cu(II) 13.5 kJ mol-1. The low value of Ea shows that Cu(II) adsorption process by zeolite NaA may be an activated chemical adsorption. The thermodynamic parameters (ΔG0, ΔH0, and ΔS0) were also determined from the temperature dependence. The results show that the process of adsorption Cu(II) is spontaneous and endothermic process and rise in temperature favors the adsorption.
Abstract: Brick is one of the most common masonry units used as building material. Due to the demand, different types of waste have been investigated to be incorporated into the bricks. Many types of sludge have been incorporated in fired clay brick for example marble sludge, stone sludge, water sludge, sewage sludge, and ceramic sludge. The utilization of these waste materials in fired clay bricks usually has positive effects on the properties such as lightweight bricks with improved shrinkage, porosity, and strength. This paper reviews on utilization of different types of sludge wastes into fired clay bricks. Previous investigations have demonstrated positive effects on the physical and mechanical properties as well as less impact towards the environment. Thus, the utilizations of sludge waste could produce a good quality of brick and could be one of alternative disposal methods for the sludge wastes.
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: Adsorption of Toluidine blue dye from aqueous solutions onto Neem Leaf Powder (NLP) has been investigated. The surface characterization of this natural material was examined by Particle size analysis, Scanning Electron Microscopy (SEM), Fourier Transform Infrared (FTIR) spectroscopy and X-Ray Diffraction (XRD). The effects of process parameters such as initial concentration, pH, temperature and contact duration on the adsorption capacities have been evaluated, in which pH has been found to be most effective parameter among all. The data were analyzed using the Langmuir and Freundlich for explaining the equilibrium characteristics of adsorption. And kinetic models like pseudo first- order, second-order model and Elovich equation were utilized to describe the kinetic data. The experimental data were well fitted with Langmuir adsorption isotherm model and pseudo second order kinetic model. The thermodynamic parameters, such as Free energy of adsorption (AG"), enthalpy change (AH') and entropy change (AS°) were also determined and evaluated.
Abstract: Three alumina-supported Pt-Sn catalysts have been
prepared by means of co-impregnation and characterized by XRD and
N2 adsorption. The influence of catalyst composition and reaction
conditions on the conversion and selectivity were investigated in the
hydrogenation of acetic acid in an isothermal integral fixed bed
reactor. The experiments were performed on the temperature interval
468-548 K, liquid hourly space velocity (LHSV) of 0.3-0.7h-1,
pressures between 1.0 and 5.0Mpa. A good compromise of
0.75%Pt-1.5%Sn can act as an optimized acetic acid hydrogenation
catalyst, and the conversion and selectivity can be tuned through the
variation of reaction conditions.
Abstract: The purpose of this research is to establish the experimental conditions for removal of Cibacron Brilliant Yellow 3G-P dye (CBY) from aqueous solutions by sorption onto coffee husks as a low-cost sorbent. The effects of various experimental parameters (e.g. initial CBY dye concentration, sorbent mass, pH, temperature) were examined and the optimal experimental conditions were determined. The results indicated that the removal of the dye was pH dependent and at initial pH of 2, the dye was removed effectively. The CBY dye sorption data were fitted to Langmuir, Freundlich, Temkin and Dubinin-Radushkevich equilibrium models. The maximum sorption capacity of CBY dye ions onto coffee husks increased from 24.04 to 35.04 mg g-1 when the temperature was increased from 293 to 313 K. The calculated sorption thermodynamic parameters including ΔG°, ΔH°, and ΔS° indicated that the CBY dye sorption onto coffee husks is a spontaneous, endothermic and mainly physical in nature.
Abstract: Mercury adsorption on soil was investigated at
different ionic strengths using Ca(NO3)2 as a background electrolyte.
Results fitted the Langmuir equation and the adsorption isotherms
reached a plateau at higher equilibrium concentrations. Increasing
ionic strength decreased the sorption of mercury, due to the
competition of Ca ions for the sorption sites in the soils. The
influence of ionic strength was related to the mechanisms of heavy
metal sorption by the soil. These results can be of practical
importance both in the agriculture and contaminated soils since the
solubility of mercury in soils are strictly dependent on the adsorption
and release process.