Abstract: In the past many uneconomic solutions for limitation
and interruption of short-circuit currents in low power applications
have been introduced, especially polymer switch based on the
positive temperature coefficient of resistance (PCTR) concept.
However there are many limitations in the active material, which
consists of conductive fillers. This paper presents a significantly
improved and simplified approach that replaces the existing current
limiters with faster switching elements. Its elegance lies in the
remarkable simplicity and low-cost processes of producing the device
using polyaniline (PANI) doped with methane-sulfonic acid (MSA).
Samples characterized as lying in the metallic and critical regimes of
metal insulator transition have been studied by means of electrical
performance in the voltage range from 1V to 5 V under different
environmental conditions. Moisture presence is shown to increase the
resistivity and also improved its current limiting performance.
Additionally, the device has also been studied for electrical resistivity
in the temperature range 77 K-300 K. The temperature dependence of
the electrical conductivity gives evidence for a transport mechanism
based on variable range hopping in three dimensions.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: In this paper, we proposed the effects of Mo thickness
on the properties of AZO/Mo/AZO multilayer thin films for
opto-electronics applications. The structural, optical and electrical
properties of AZO/Mo/AZO thin films were investigated.
Optimization of the thin films coatings resulted with low resistivity of
9.98 × 10-5 )-cm, mobility of 12.75 cm2/V-s, carrier concentration of
1.05 × 1022 cm-3, maximum transmittance of 79.13% over visible
spectrum of 380 – 780 nm and Haacke figure of merit (FOM) are 5.95
× 10-2 )-1 under Mo layer thickness of 15 nm. These results indicate an
alternative candidate for use as a transparent electrode in solar cells
and various displays applications.
Abstract: Steel corrosion in concrete is considered as a main
engineering problems for many countries and lots of expenses has been paid for their repair and maintenance annually. This problem
may occur in all engineering structures whether in coastal and offshore or other areas. Hence, concrete structures should be able to
withstand corrosion factors existing in water or soil. Reinforcing
steel corrosion enhancement can be measured by use of concrete
electrical resistance; and maintaining high electric resistivity in concrete is necessary for steel corrosion prevention. Lots of studies
devoted to different aspects of the subjects worldwide. In this paper, an evaluation of the effects of W/C ratio, cementitious materials, and
percent increase in silica fume were investigated on electric resistivity of high strength concrete. To do that, sixteen mix design
with one aggregate grading was planned. Five of them had varying amount of W/C ratio and other eleven mixes was prepared with
constant W/C ratio but different amount of cementitious materials.
Silica fume and super plasticizer were used with different proportions
in all specimens. Specimens were tested after moist curing for 28 days. A total of 80 cube specimens (50 mm) were tested for concrete
electrical resistance. Results show that concrete electric resistivity can be increased with increasing amount of cementitious materials
and silica fume.
Abstract: In projects like waterpower, transportation and
mining, etc., proving up the rock-mass structure and hidden tectonic
to estimate the geological body-s activity is very important.
Integrating the seismic results, drilling and trenching data,
CSAMT method was carried out at a planning dame site in southwest
China to evaluate the stability of a deformation. 2D and imitated 3D
inversion resistivity results of CSAMT method were analyzed. The
results indicated that CSAMT was an effective method for defining
an outline of deformation body to several hundred meters deep; the
Lung Pan Deformation was stable in natural conditions; but uncertain
after the future reservoir was impounded.
This research presents a good case study of the fine surveying and
research on complex geological structure and hidden tectonic in
engineering project.